Search Documents

By Ulf B. Andersson, Christina Dahnér-Lindkvist, Bruno Figueiredo, Jessa Vatcher, Jonny Sjöberg, Joel Andersson

Hydraulic fracturing to precondition the rock mass in high seismic risk environments has great potential. Unfortunately, there are many unanswered questions about how to best implement a hydraulic fracturing program at individual mine sites, and even how to best use our engineering tools to evaluate these plans. To give the hydraulic fracturing field tests at LKAB’s Kiirunavaara Mine the best chance of success, fully-coupled, discontinuum numerical modelling Itasca’s 3DEC code was used together with statistical simulations of the fracture network. For modelling purposes, it was assumed that hydraulic fracturing successfully reduces seismic risk through 1) the creation of hydraulic fractures along a plane at each injection site, and 2) activation of existing discontinuities. A variety of scenarios for the mine were evaluated, which focused on site specific uncertainties (such as the spacing of the pre-existing discontinuities) and practical solutions (such as the hydraulic fracture spacing, selection of injection medium, and hydraulic fracture site location relative to production). The discrete fracture network (DFN) realizations were developed using available statistical data for discontinuities near where hydraulic fracturing was planned.

Apr 26, 2022

By F. X. Prins, L. R. Nelson

Tight control of electrode paste additions, hard and soft paste levels, baked zone position and electrode temperatures are integral to superior Söderberg electrode management practices. Paste addition is typically effected through briquettes, cylinders or large blocks. Each electrode paste form has its advantages and disadvantages, but probably a more crucial element from an electrode control perspective is the frequency and amount of electrode paste addition into a Söderberg electrode column. The detrimental effects of excessive soft paste levels leading to Stokes? Law segregation of paste in the electrode column are well documented, while several operators have effectively implemented the use of electrode thermocouples to monitor paste temperatures and automated slipping algorithms to control baking conditions within electrodes. Somewhat less well appreciated are the negative influences of inadequate soft paste levels, especially when coupled with excessive paste cylinder or block additions and resulting high hard paste levels. The alternative of insufficient hard paste levels and associated overheated electrode paste must also be considered, and can contribute to paste segregation directly. This condition also has the potential to generate gas mixtures in the electrode column that are concurrently a potential health hazard, while being prone to spontaneous combustion. Results of industrial trials on electric furnaces using Söderberg electrodes in a variety of applications from ferrochromium, to ferromanganese and even platinum-bearing base metal sulphides smelting are presented to illustrate the influence of paste loading practices on the dynamics of hard and soft paste levels. Possible electrode failure mechanisms attributable to inadequate paste level control will be discussed through some industrial examples. Suitable paste loading practices to mitigate the risks of inappropriate paste levels and associated electrode incidents are presented.

Jan 1, 2004

By Alejandro Rubio-Lopetegui, Gonzalo Montes-Atenas

The occurrence of Enargite (Cu3AsS4) in hydrometallurgical plants bears a number of challenges. One question lies on how Copper and Arsenic can be selectively extracted from the solid surface structure when immersed in aqueous solution. The leaching of Enargite in ambient conditions has been extensively studied; nevertheless, challenges regarding the process kinetics and surface structures enabling the extraction process remain ill-understood. Prior knowledge indicates that different conditions of pH, Eh, temperature, speciation of the aqueous phase or variations of these parameters defines the overall rate at which metals and other elements will be transferred to the solution. One aspect that the research studies have seldom addressed involves studying the main features of the surface structures formed during the leaching process at the outmost surface atomic layer. Such structures will mediate between the solid bulk and the solution to undertake subsequent stages of leaching process. The aim of this research work is to critically analyze the state of the art of Enargite electrochemistry from the mediator formation-dissolution mechanisms standpoint occurring at the mineral-solution interface. The most probable mediator species reported in the literature were found to be: Arsenolite and Sulfur (acidic media), Covellite (acidic and alkaline media) and Tenorite (alkaline media). As a result of this analysis, it was observed that the surface speciation was not in full agreement with the previous knowledge suggested to explain Enargite leaching reactions and, therefore, modified Eh-pH diagrams are presented. The acquired insights on the surface structures rising from the Enargite-aqueous solution interactions is further revised to provide new experimental protocols towards selectively separating Copper and Arsenic through hydrometallurgical paths.

Jan 1, 2014

By Philippe De Donato, Odile Barres, Mukendi Kongolo, Stoyan Gaydardzhiev, David Bastin, Jean-Marie Kanda

The adsorption patterns of potassium amylxanthate on the surface of high purity malachite subjected to prior sulfidization with NaSH have been followed and elucidated. DRIFTS spectroscopy has been used to trace the associated physicochemical alterations as well as the chemical species present on the mineral surface. Varying the collector concentration from 5.10-4 to 1.10-2 mol/L has led to different degree of surface coverage of the alkyl groups and to formation of organometallic hydrophobic complexes of CuX or CuX - X2 type. The results reveal that the CuX complex formed on the malachite surface without sulfidizing agent is more unstable and prone to dissolution-precipitation phenomena. Based upon the constructed adsorption isotherms and upon the degree of statistical coverage, different zones of mineral-reagent interactions could be distinguished. They correspond respectively to the monolayer, bi-layer and tridimensional condensation domains. In each of the identified zones mono or double layer adsorption patterns of the collector are proposed leading respectively to formation of surface compounds with different degree of hydrophobicity. The results suggest that sulfidisation remains an important prerequisite in view achieving efficient flotation of the malachite from the studied copper ore.

Jan 1, 2014

By Peter J. Nicholson

The methods of reinforcement to be discussed in this paper are all insitu methods, ones that can be used on the soil structure as it exists in the ground, and do not rely on excavation and replacement of the soil. Current practice in the United States, as well as new ideas and methods, will be discussed as they relate to slope stability, retaining walls, and to other uses such as control of mine or cavity related subsidence and to liquefaction control under existing structures. The method is based on the concept of "nailing" or reinforcing the soil in place, and thereby causing a mass of soil to act as a coherent unit. When performed properly, a true gravity structure can be constructed, one that will remain intact under both horizontal and vertical loadings and that will also resist vibrational and seismic loadings.

Jan 1, 1991

By S. C. Termes, P. E. Richardson, R. L. Wilfong

This paper discusses recent Federal Bureau of Mines research on the selective flocculation of various minerals with insoluble cross-linked starch xanthate (ISX). ISX is insoluble, has a shelf life of more than a year when kept cold, and has a higher molecular weight due to cross-linking than the soluble, non-cross-linked starch xanthate used in previous flocculation studies on nonsulfide minerals. ISX readily flocculates a number of sulfide mineral fines, but no silicious gangue. Floc formation, floc size, and settling rate are dependent on pH. The pH dependence, however, differs for each mineral. Bornite has been selectively flocculated from bornite-quartz mixtures, and the bornite-containing flocs were separated from the unflocculated quartz using decantation and washing procedures.

Jan 1, 1984

By S. C. Termes

This paper discusses recent Federal Bureau of Mines research on the selective flocculation of various minerals with insoluble crosslinked starch xanthate (ISX). ISX is insoluble, has a shelf life of over a year when kept cold, and has a higher molecular weight due to cross linking than the soluble noncrosslinked starch xanthate used in previous flocculation studies on nonsulfide minerals. ISX readily flocculates a number of sulfide mineral fines but not silicious gangue. Floc formation, floc size, and settling rate are strongly dependent on pH, with the pH dependence differing for each mineral. Bornite has been selectively flocculated from bornite-quartz mixtures, and the bornite-containing flocs were separated from the unflocculated quartz using decantation and washing procedures.

Jan 1, 1982

"Full time inspection of drilled shafts by qualified personnel is a necessary part of construction. Detailed inspection procedures for routine inspection are provided in the Drilled Shaft Inspector’s Manual, published jointly by the DFI and ADSC: the International Association of Drilled Shaft Contractors.The use of NDT methods or other observation methods, such as probes, video camera inspection, remote shaft wall inspection devices or various calipers are not suitable substitutes for routine "topside" construction inspection as described in the Drilled Shaft Inspector’s Manual. However, these NDT and other "remote" or indirect observation methods are valuable alternatives to direct entry of personnel into drilled shaft excavations. They should be considered whenever appropriate to reduce the risks of direct entry of personnel into drilled shaft excavations.As described in the Drilled Shaft Inspector’s Manual, observations made during construction are essential for quality construction of drilled shafts. The shaft depth, diameter, plumbness, bottom conditions, reinforcement, concrete continuity, and bearing conditions are most easily checked during construction. Some of these observation methods include excavation around the shaft for relatively shallow inspection, down-hole inspection for end bearing conditions or rock sockets, and video camera devices for remote inspection. In rare circumstances, a drilled shaft can be extracted for inspection. Before concrete placement, the bottom of the shaft can also be probed by drilling or coring to determine if there are voids or soft zones in the material at the base of the shaft.The Drilled Shaft Inspector’s Manual focuses on traditional "topside" inspection for routine drilled shaft construction."

Jan 1, 2004

The Daly-Judge Tunnel, begun in 1887 to drain mine workings, is now a source of potable water for the Municipality of Park City. The water is exceptionally clean; however, when roof falls occur, suspended solids levels become too high and water from the tunnel cannot be used in the treatment plant. In 2001, the tunnel was inspected and rehabilitated to ensure that the water supply for the 2002 Winter Olympic Games would be uninterrupted. Twenty-five timber tunnel sets were removed, and 86 steel sets were installed. Timber lagging was installed or replaced over about 230 m (750 ft) of tunnel length.

Jan 1, 2006

By Yadong Xue, Fei Wang, Hongwei Huang, Yan Sun

"Increasing attention to subway tunnel maintenance is being paid with the high speed development of urban rail transit system in China. A novel moving tunnel inspection equipment based on machine vision is developed in this paper. High resolution image acquisition system is proposed for tunnel crack and leakage inspection. The main components of this image acquisition system includes high speed CCD cameras, linear lights and high performance computer. To inspect the crack less than 0.3mm with a 3-5km/h speed in subway tunnel, we need to consider resolution and line rate of camera, pixels of cameras, range of inspection and illumination intensity of lights simultaneously. The optimization design is proposed to make the equipment more convenient for tunnel use. Entire tunnel situation can be detected and recorded in a single inspection process. This equipment has already been verified in Shanghai subway tunnel for defects inspection.1. INTRODUCTION In China, the quantity of subway tunnel has reached a large scale in recent years. Until 2014, there had been more than 2300km of subway tunnel in China which accounted for nearly three quarters of Chinese urban railway system (Zhang Chen,2015). In some metropolises like Beijing and Shanghai, most of the metro tunnels has already run over 20 years which within maintenance phase. This has brought about plenty of inspection work and maintenance work to guarantee the tunnel under the serviceability limit states. The increase of running mileage of subway tunnels in China has been displayed in Fig 1."

Jan 1, 2016

By O. Tranbarger

In aging tunnels, wall and roof deterioration can eventually result in defects that must be detected and repaired to maintain safe structural conditions. In investigating tunnel defect conditions, a specialized FM radar system was developed with a programmable VHF and UHF operating sweep range for optimizing the penetration and measurement capabilities. The new FM radar technology was tested in two aging brick-lined tunnels in New York City. Test results showed that FM radar signals could penetrate eight courses of water-saturated brick and that the original steel liner outside the tunnel walls was intact.

Jan 1, 1985

This manual provides basic practical instruction on the inspection of driven piles. It covers the essential components of pile driving, such as the pile driving hammer, hammer accessories, the pile and soil, and frequently encountered test methods in an uncomplicated, yet knowledgeable, and practical manner. Insight is given into the methods of installing the foundation, dealing with the cranes which do the lifting, the hammers which do the driving, the leads that guide the hammer and pile, the compressors which provide the external power when required, and finally prevalent analysis tools and testing instrumentation and procedures which enable you, the Inspector, to do your job. This DFI Inspector's Manual for Pile Foundations will help the Pile Inspector who has limited knowledge of pile foundations. Perhaps this Inspector has been pressed into service at a moments notice; a few helpful hints and suggestions to him are desperately needed and he can look here for the basics. It is also useful for the experienced Pile Inspector as a reference guide. However, this manual is not a detailed check list of every possible scenario and detail which could ever be encountered. There are other sources available which give more detailed descriptions (and should be consulted by the Inspector when appropriate; a list of this additional reference material is provided and suggestions made in appropriate chapters of this text). The current manual is more a brief "textbook overview" with some of the more important aspects given at least some emphasis so that the Inspector has some direction and hopefully helps to produce a safe, yet economical, foundation.

Jan 1, 1997

By Matthew E. Meyer

The intent of this manual is to provide guidelines for observing and documenting the installation of ACIP piles. The manual may also serve as a guide for the training of inspection personnel. It is expected that the general guidelines and procedures described in this manual for the inspection and installation of ACIP piles will be supplemented by engineering judgment, local practice, and experience. ACIP pile construction procedures will vary depending on soil, rock, and groundwater conditions. This manual represents a wide range of possible applications in a variety of projects. It is not intended to be applicable in all situations nor replace engineering judgment for any given project. Therefore, an all-inclusive inspection manual is not considered practical or desirable. This manual should not be used to interpret or replace project specifications. It has, however, been prepared to complement the Augered Castin- Place (ACIP) Piles Manual model specification (DFI, 2003).

Jan 1, 2010

This manual is limited to Augered Cast-in-Place (ACIP) piles constructed using a hollow stem continuous flight auger. 1.1SCOPE AND LIMITATIONS The intent of this manual is to provide guidelines for observing and documenting the installation of ACIP piles. The manual may also serve as a guide for the training of inspection personnel. It is expected that the general guidelines and procedures described in this manual for the inspection and installation of ACIP piles will be supplemented by engineering judgment, local practice, and experience. ACIP pile construction procedures will vary depending on soil, rock, and groundwater conditions. This manual represents a wide range of possible applications in a variety of projects. It is not intended to be applicable in all situations nor replace engineering judgment for any given project. Therefore, an all-inclusive inspection manual is not considered practical or desirable. This manual should not be used to interpret or replace project specifications. It has, however, been prepared to complement the Augered Cast-in-Place (ACIP) Piles Manual model specification (DFI, 2003).

Jan 1, 2010

AMONG the features that make Inspiration of outstanding A interest, particularly to the engineer, is the fact that at various times it has used, as a major method of production, three more or less distinct methods of mining and three distinct methods of treating its ores. The following chronology is of interest : Major Mining Methods: 1915-194 7 Underground block-caving, exclusively 1948-1952 Underground block-caving and opencut mining 1953-1954 Underground block-caving, opencut mining, and "glory-hole caved-block transfer" mining 1955 on Opencut mining and "glory-hole caved-block transfer" mining. Major Ore Treatment Methods: 1915-1925 Flotation concentration exclusively 1926-1930 Flotation concentration and ferric sulphate leaching 1931-1955 Ferric sulphate leaching (the so-called "Dual Process" was used for eleven months in 1937 when demand for copper was phenomenal; and the "leach-float" process was used for 24 months in 1942-44 as an expedient to help meet war demands for copper). 1956 on "Dual Process" combining a sulphuric acid leach followed by fine grinding and flotation of the residue from the leaching vats.

Jan 1, 1957

AMONG the fellow prospectors of Black Jack Newman, locator of the claims that became the Miami mine, were J. D. Coplen and Bud Woodson. Woodson was in the district when the Bloody Tanks Indian massacre occurred, near the present town of Miami. He was a prospector long before Jack Newman worked in a mine, and for years he had done assessment work on some of the claims that Coplen acquired for his Inspiration company. Woodson recalls that a Scotch geologist from Morenci once visited his claims; and that the geologist tried to get the Phelps Dodge company interested in the property, but without success. Coplen interested some people in Kansas City in his claims that lay west of Newman's. He induced them to organize the Inspiration Mining Co., and by 1908 this company controlled 23 claims, which had been prospected in desultory fashion by a series of adits. One of these, near the Keystone property, encountered some lean copper-bearing rock, but later development failed to disclose any substantial quantity of ore at this particular point. Coplen, as general manager, in September, 1908, was negotiating with several exploration companies which at the time were on the lookout for low-grade copper properties. As a matter of fact, when J. Parke Channing visited Globe, in December, 1906, F. C. Alsdorf showed him the Inspiration claims as well as Newman's. Channing evinced little interest in an option on Inspiration because he could get so much better terms from Newman. He decided to concentrate his work on the Newman claims, with the idea that if he were successful in developing ore, he could later get Inspiration on terms at least equally good. Subsequently, the United States Smelting & Refining Co., which has since added "Mining" to its corporate name, took an option on Inspiration.

Jan 1, 1933

By H. C., Weed

THE Inspiration Consolidated Copper Co., located in the Globe-Miami district at Inspiration, Ariz., became a producer of copper in 1915. From 1915 until 1948, 116,278,000 tons of ore were produced from underground workings by the block-caving system of mining. In April 1948, open-pit ore production from portions of the ore body was started and earlier plans for block-caving in these areas were abandoned. The change was due to economic conditions. Prior to the war years Inspiration's costs of mining by block-caving methods were comparable to, or even below, the costs of some open-pit operations. By the end of the war these conditions were completely changed. Underground costs had risen steadily for labor and supplies. Difficulty was being experienced in finding competent underground men and underground development was almost hopelessly behind schedule. On the other hand, open-pit costs had been sharply reduced through the development of modern earth-moving machinery and plenty of labor was available for surface work.

Jan 1, 1950

By H. C. Weed

THE Inspiration Consolidated Copper Co., located in the Globe-Miami district at Inspiration, Ariz., became a producer of copper in 1915. From 1915 until 1948, 116,278,000 tons of ore were produced from underground workings by the block-caving system of mining. In April 1948, open-pit ore production from portions of the ore body was started and earlier plans for block-caving in these areas were abandoned. The change was due to economic conditions.

Jan 8, 1950

By D. L. Ealy

At the Beckley Mine in southern West Virginia, forecasting unstable roof conditions in advance of mining is accomplished by using a rating system that combines historical information on mine roof failures with known mine geology. Failure frequency rates are derived for each category of roof rock composition, unit thickness, structure, and extraction ratio. In this manner, known geological environments are rated according to instability based on actual experience. Drill hole control and geological interpretation provide the basis for forecasting unstable conditions beyond working faces. The forecasting technique has assisted mine management in reducing fall frequencies by 80% over the past two years compared to the first five years of operation. This reduction in fall frequency was accomplished by modifying the plan of advancing sections to minimize mining exposure to unstable roof conditions.

Jan 1, 1980

By Panshi Xie, Yingyi Zhang, JIANJIE DUAN, Shenghu Luo

A multi-layer gangue roof of a steeply dipping coal seam with a large mining height face area was analyzed using physical simulation, numerical simulation, theoretical analysis, and field measurement methods to evaluate the roof deformation and the mechanisms associated with the instability of the hard gangue and soft coal interlayer. The results indicated that the first weighting step of the multi-gangue roof was larger than that of a non-gangue roof, but periodic weighting steps were similar. The overburden collapse height was lower in the multi-gangue roof than in the non-gangue roof due to the buffering and supporting function of the collapsed gangue. Moreover, the failure of the coal interlayer was the key factor in the collapse of the multi-layer gangue. A mechanical model was established for the hard gangue and soft coal interlayer based on a revised Prandtl squeezing theory. The limited load of the interlayer and maximum resistance of the shield support was thusmodeled. The maximum resistance of the support increased with the dip angle of the seam and burial depth. It also increased with the interlayer thickness at thicknesses below 2.75 m. It reached a peak when the interlayer thickness was between 2.75 and 3 m and exhibited a decreasing trend when the thickness was greater than 3 m. The results were confirmed using physical simulation and a field test. Certain measures were proposed to control the stability of the gangue roof, including zoning control of the mining height and resistance and advancing the support while maintaining roof contact, thus ensuring the integrity of the support and surrounding rock system.

Jun 30, 2020