Search Documents

By L. K. Witika, J. H. Masinja

"Investigations of flotation characteristics of Lumwana and Kansanshi ores using formulated frothers were carried out. Of the six frothers tested, two came from the alcohol family, two from the glycol family and last two were formulated products. The initial work involved determining the optimum mesh of grind and frother dosage for Lumwana and Kansanshi ores. Further work involved carrying out surface tension, bubble size and froth stability measurements. Finally, water recovery tests were conducted at Lumwana and Kansanshi mine sites. For froth stability tests, six frothers were tested on a two-phase (water–air) system using the Bikerman column flotation cell, while water recovery tests were conducted using a total of seven frothers, including the standards for each plant. The results of the testwork showed that (i) although a stable froth is essential for optimum recovery of valuable minerals, a higher molecular weight frother, like Dowfroth 250, caused poor selectivity when used on fine ores and (ii) a lower molecular weight frother was suited for Lumwana ore, while a mid to higher molecular weight formulated product was suitable for Kansanshi sulphide ore. INTRODUCTION Investigations of flotation characteristics of Lumwana and Kansanshi ores using formulated frothers were carried out. The initial work of this project involved determining the optimum mesh of grind and frother dosage for Lumwana and Kansanshi ores. Further work involved carrying out surface tension, bubble size and froth stability measurements. Finally, water recovery tests were conducted at Lumwana and Kansanshi mine sites. In order to investigate the gangue entrainment levels in the Lumwana and Kansanshi sulphide ores, two well-known methods (froth stability and water recovery) were used. Firstly, froth stability tests were conducted using six frothers, two from the glycol family (Dowfroth 200 and Dowfroth 250), two from alcohol family (MIBC and pine oil) and other two from the formulated family (Betafroth 20 and Betafroth 245), at the University of Cape Town’s Centre for Mineral Research (CMR) laboratories. Froth formation and stability measurements were conducted using the Bikerman column flotation cell."

Jan 1, 2015

By K. C. Corin, M. S. Manono, J. G. Wiese

Depressants play a crucial role in the flotation of PGM bearing ores as they prevent naturally floatable gangue (NFG) from reporting to the concentrate. This action is regarded as critically important because less dilution of the concentrate means lower costs for downstream processes. However, abnormal water conditions (such as high concentrations of ions) in the flotation system can modify the selectivity of these depressants. It is well known that the existence of selected electrolytes in water can alter the behaviour of some polysaccharide depressants by enhancing their adsorption onto gangue minerals and thereby prevent naturally floatable gangue from moving into the froth phase. Concurrently these same electrolytes may enhance frothability, owing to their stabilising effect on the bubbles within the system. Plant water at various ionic strengths was investigated against depressant type and dosage in order to understand electrolyte-depressant interactive effects during the flotation of a Merensky ore, using entrainment, rate of NFG recovery, and total gangue recovery as proxies. The study showed that the rate of NFG recovery per unit mass of water decreased with increasing ionic strength at all dosages, however the total amount of gangue reporting to the concentrate increased with increasing ionic strength at all depressant dosages. Thus, this paper attempts to consider the effects of both ionic strength and depressant dosage as individual factors within flotation. It further looks to investigate whether any interactive effects exists between these two factors when considered simultaneously.

Jan 1, 2016

By N Esmaeili, M Saghaeian, L Hosseini, V Sheikhzadeh, R Hejazi

Ore roasting has long been used for beneficiation and assay upgrading of different ores. In this process, which is mainly used for sulfide ores, the ore is heated to a high temperature. More specifically, it is a metallurgical process involving gas-solid reactions at elevated temperatures. Some types of Iron ore are weak in magnetic properties. Hematite, goethite and limonite are classified in this group. Unlike magnetite, which shows strong magnetic susceptibility, these ores are hard to beneficiate through magnetic separation route. Many researches have focused on gravity separation and flotation routes for upgrading these ores and these methods have also been utilised in the industry. One of the methods to whose industrial application less attention has been paid is magnetising roasting in which the non-magnetic iron ore is transformed to magnetite which is further beneficiated through magnetic separation. In this study, magnetising roasting tests have been performed on one goethite sample in order to check the feasibility of using this method for this specific ore in industrial scale. It is worth mentioning that high intensity magnetic separation have been performed on this sample before but the achieved results were not promising. Results have revealed that through magnetising roasting magnetite content of the ore could be increased from 1.7 per cent up to about 25 per cent. FeO content of the feed sample was increased from 1.03 per cent up to around 9.25 per cent. Also optimum size distribution for achieving the best results in magnetising roasting for this sample has been determined through this study. The best results were achieved when the ore size was 0–10 mm. The effect of coal ratio, time and temperature on the process have also be studied. A coal ratio of 5 per cent, time of 30 min and a temperature of 850°C were determined to be the optimum conditions. Finally, the technical feasibility of utilising magnetising roasting for this specific ore has been confirmed.

Aug 24, 2022

By K. Awuah-Offei, A. U. Rehman

"Information diffusion potential of a social media user affects how quickly information about a mineral project can diffuse through that user. If management can use social media and network analysis, in community engagement program, to understand how fast and how far information will diffuse to communities and followers of particular social media users, it can selectively focus on the most influential users. This paper proposes a method to examine the information diffusion potential of social media accounts. The work uses Gephi, an open source software, to extract and analyze data from different Twitter handles to predict their information diffusion potential. The work uses case studies of real Twitter users (e.g. mining news organizations and bloggers) associated with mining to illustrate the approach. The case study results show that there are significant disparities in information diffusion potential that will demand selective attention. This research will help mines develop effective social media engagement strategies. INTRODUCTION The mineral industry provides raw material for industrial activity to support our society (Martens and Rattmann, 2001). Mines have changed conventional mining practices to sustainable ones because of the negative impacts of mining and increased public awareness (Wang et al 2016). The concept of sustainable mining is getting mature as stakeholders (e.g., governments, investors and host communities) are getting involved in mining projects (World Economic Forum, 2014). The failure of mining companies to address the demands of these stakeholders might result in failure to acquire social license to operate (Thomson and Boutilier, 2011). The social license to operate (SLO), if granted, is mutually beneficial to all stakeholders. Mines prefer being granted SLO and keeping it to avoid any kind of social unrest due to their operation (Prno, 2013; Moffat and Zhang, 2014). Mining communities can grant different levels of SLO; ranging from withholding SLO to psychologically identifying with the project (Joyce and Thomson, 2000; Thomsan and Boutilier, 2011). Most of the previous work to understand community perceptions and SLO in mining is generally qualitative (ICMM, 2012a; Thomson and Boutilier, 2011; Prno, 2013; Moffat and Zhang, 2014; IFC, 2014). In particular, there is limited work on how community perceptions change over time due to information diffusion (Boateng and Awuah-Offei, 2017). However, SLO changes with respect to time (Yates and Horvath, 2013), which can result in risks that are not easy to predict. Mine managers and engineers have a desire to understand these changes so as to mitigate these risks (Que and Awuah-Offei, 2014; Que et al., 2015)."

Jan 1, 2018

By N. Bat, N. Sarantsatsral

Blasthole sampling practices were investigated at the Erdenet copper and molybdenum mine in Mongolia to address grade reconciliation issues. The goal of the study was to determine if the particle size distribution (PSD) of blasthole cuttings was accurately reflected in the samples. The study additionally examined if the measured grade was related to the particle size of samples. Using a sector sampler specifically designed to collect samples for the study, six large samples were collected from three blocks following a specialized protocol. Each sample was split into nine size fractions, ranging from larger than 12 mm to smaller than 63 µm. Copper and molybdenum grades were determined for each of the size fractions. For comparison, nine samples were collected from the same blocks following the standard mine sampling protocol. These samples were also split into the same nine size fractions. As with the other samples, grades were determined for each of the size fractions. The results showed that the PSD in the samples collected following the standard operating procedure varied significantly from sample to sample. This variation was much lower for the samples collected following the specialized protocol. Loss of fines was also indicated in the standard mine sampling process. These observations suggest that the standard sampling protocol did not consistently capture the PSD. The copper and molybdenum grades increased as particle size decreased, regardless of the sampling protocol used. This observation underscores the importance of the PSD of a sample being representative of the true PSD. Given the low number of samples in the study, it is not a strong conclusion that the standard sampling protocol captures the PSD inconsistently. However, it could be taken as a caution. On the other hand, the grade versus PSD relationship is more certain, given that it was observed regardless of the sampling method used.

Feb 1, 2017

By Joshua Hoffman, Braden Lusk, David McLane, John Rathbun

The research conducted previously on Shock-Tunnel Waveform Analysis gave a brief insight into the propagation of a shockwave within a shock-tunnel compared to that of an open air arena test. As a refresher, a shock-tunnel is an energy channeling device used to simulate the effects of a large scale detonation with significantly smaller charge weights; having the ability to conduct tests in this fashion can greatly reduce the costs of testing products.

Jan 1, 2012

By D Flint, K Vague

The Work Health and Safety Act 2020 (WA) (WHS Act; DMIRS, 2020) and associated Work Health and Safety (Mines) Regulations 2022 (WA) (WHS Regulations; DMIRS, 2022), supporting guidance materials and other laws, such as the Sex Discrimination Act 1984 (Cth) (SD Act), have imposed new duties on every person or business conducting an undertaking (PCBU) in Western Australia, including those operating in the mining industry. These laws and associated guidance materials combine to require owners, operators and contractors to discharge positive duties and better report and manage psychosocial hazards in the workplace. For mine operators, there is a positive duty to not only identify and eliminate hazards relating to psychological harm, sexual harassment and gendered violence at work, but to also report incidents to the safety regulator that could result in serious harm, even while internal and police investigations are ongoing. Traditional mines safety teams are navigating the evolving frontier of psychological and gendered safety as the duties relating to psychosocial safety and sexual harassment at work continue to expand. This paper will review the legal obligations on PCBUs to conduct internal investigations into critical psychosocial incidents and gendered violence on mines, whilst balancing the demands and sensitivities of investigations by the safety regulator and police. There are emerging approaches to safety investigations that can aid PCBUs in managing their investigations of psychosocial incidents and gendered violence, including trauma-informed investigation techniques, collaboration with psychological experts and the use of limited legal privilege. Well managed and sensitive investigations can foster trust amongst workers, result in improved incident reporting by workers and lead to enhanced safety outcomes for the resources industry whilst preserving the legal positions of involved PCBUs. Specifically traversing the new duty to consult, cooperate and coordinate, this practical session will arm mine managers, safety professionals and human resources professionals, from mine operators and mining contractors alike, with tools and processes to bring to safety investigations, particularly on residential mine sites.

Apr 16, 2024

By C. Guney Olgun, Mohammad Khosravi, Daniel W. Wilson, Deepak Rayamajhi, Scott A. Ashford, Shuji Tamura, Ross W. Boulanger

"Dynamic centrifuge tests were performed on unimproved and improved soil with soil-cement column models. The reinforcing effect of isolated soil-cement columns for reducing liquefaction potential and ground deformation in improved soil were investigated. This paper presents the observed acceleration, pore pressure, and settlement responses under an earthquake base motion for both unimproved and improved soil models. In addition, lateral reinforcing effects of soil-cement columns were also investigated in terms of site stiffening effects and the increasing natural frequency of improved soil. The test results show that the soil-cement columns were rather ineffective in preventing liquefaction triggering in improved soil and in significantly reducing the magnitude of the resulting soil settlement compared to the model with unimproved soil profile. Furthermore, the predicted natural frequency of the improved soil profile estimated using existing design equations is shown to be significantly higher than the observed natural frequency inferred from centrifuge tests results. These design equations assume shear strain compatibility between the columns and the surrounding soil. On the other hand, revised design equations that account for shear strain incompatibility between column and surrounding soil are shown to give reasonable estimates compared to the observed natural frequency of the improved soil model.INTRODUCTIONGround improvement using stiff columns (e.g., stone columns, deep-soil-mixing columns, and jet-grout columns), are often used in practice to reduce liquefaction potential (and associated deformations) in loose soil sites. Typically, saturated silty soils are difficult to densify or drain rapidly due to their lower hydraulic conductivity, so densification and drainage techniques of improvement are often found to be ineffective. Instead, the shear reinforcing mechanisms of stiff columns are considered effective for reducing the seismic stresses and strains, and thereby reducing liquefaction potential in the enclosed saturated silty soils (Baez 1995, Adalier and Elgamal 2004, Mitchell 2008)."

Jan 1, 2015

By K. Luxbacher, D. T. Hristopulos, S. Schafrik, J. Diaz, Z. Agioutantis

Big data is generated from both surface and underground mining operations. Such data contain a wealth of information concerning safety and health in the workplace and production parameters. This paper will discuss the progress towards developing an accurate forecasting model for methane gas concentration based on the analysis of data collected from Atmospheric Monitoring Systems in underground coal mines employing time series models. Several procedures need to be applied to raw data, such as data cleaning and filtering for outlier removal, data homogenization and segmentation, and exploratory statistical analysis. The data analyzed were retrieved from two coal operations in the Eastern US. A negative correlation between barometric pressure and methane gas concentration was established, at least for certain data segments. Such correlations raise the possibility that barometric pressure data can predict variations of gas concentration in the mine. The datasets will be further investigated to establish the robustness of barometric pressure and gas concentration correlation and explore the dependence of gas concentration on other factors related to mine design and operations

Mar 2, 2022

By Yuting Xue, Alper Kirmaci, Taghi Sherizadeh, Dogukan Guner, Khaled Mohamed

Rib brows present a significant safety hazard in underground coal mines in the United States. To address this issue, researchers at the National Institute for Occupational Safety and Health (NIOSH) and Missouri University of Science and Technology (MST) are developing a practical tool to assess both the potential of rib brow formation and the stability of any formed brows. As part of this effort, a monitoring study was conducted to assess the potential for rib brow formation in coal pillar ribs. This study was conducted in a room-and-pillar coal mine where coal pillar ribs are prone to developing rib brows. Although no rib brows formed in the instrumented pillar, data from monitoring and visual observations provided valuable insights into the loading mechanisms impacting the instrumented pillar. These findings helped identify factors that may reduce rib brow formation, including the cavability of the roof in mined areas, the applied rib support, the strength of rock partings, and the overall integrity of the coal seam. The scientific findings published in the case study aid in assessing the potential of brow formation, offering additional evidence for the need to improve rib control methods in underground coal mines.

Feb 1, 2025

By D. Collins, J. Winfield, V. Gangrade, B. Slaker, S. Braganza

"Researchers at the National Institute for Occupational Safety and Health (NIOSH) are investigating the unique pillar stability issues associated with room-and-pillar mining in dipping underground stone mines. The objective of this paper is to study the post-blast impact in and around a pillar, using microseismic monitoring. To accomplish this, a microseismic monitoring system has been installed at a dipping underground stone mine in central Pennsylvania. The microseismic system is comprised of 18 uniaxial accelerometers; 12 sensors are installed in a single pillar and 6 sensors are installed in the surrounding area. More than 4,400 microseismic events have been located near the study pillar following the blasts. The number of triggers increased significantly following the blast, and the trigger rate in the first five minutes was 60 triggers per minute and three triggers per minute over the next three hours. The processing of high-quality triggers indicated a large number of low magnitude microseismic events near the blasting face. The event locations were identified more accurately by using a 3D-velocity model, with an average 9 m expected location accuracy for this array calculated using the system data. Seismicity was absent from the core of the pillar, but significant numbers of events were found following cutter roof along a crosscut as it was developed as well as in the location of a rib failure event. Additionally, the events were located in the roof, showing high number of microseismic events within 0–10 m of the roof line compared to 10–30 m above the roof line.INTRODUCTIONGround control stability is essential to any mining operation for ensuring mineworker safety and health and preventing catastrophic failures of underground structures. The National Institute for Occupational Safety and Health (NIOSH) has conducted research in stone pillar design and has established fundamental pillar design guidelines for the underground stone industry, which resulted in the development of the S-Pillar program (Esterhuizen et al., 2011; Esterhuizen and Murphy, 2018). However, the data that makes up the S-Pillar database consists of shallow depth, flat-lying, single-level mining operations. Therefore, to expand this dataset and to develop guidelines for challenging conditions such as dipping and multi-level mines, NIOSH is currently conducting detailed pillar response investigations at mines with these characteristics. The study is being conducted using multiple research approaches, including seismic modeling and tomography, numerical modeling (Sears et al., 2019), stress monitoring, and LiDAR-based laser scanning (Slaker, Murphy, and Winfield, 2019). This paper discusses the findings from the microseismic monitoring system installed at the Pleasant Gap Mine, a steeply dipping underground limestone mine in central Pennsylvania."

Jan 1, 2019

By J. Lindström, J. Hamuyuni, M. Lundström, J. Aromaa

"The rising demand for metals today, coupled with the scarcity of primary sources for raw materials threatens both technological advancements and industrial manufacturing. In order to meet the demand, metals and other resources trapped in waste streams, have to be harnessed. This philosophy supports circular economy, where metals and other resources are kept in a closed loop. The pickling acid recovery system of most stainless steel production is one such example where the dissolved metals such as iron, nickel and chromium are currently not completely recovered due to the limitations of the current technologies. The aim of this study was to assess the available metals recovery methods from extremely concentrated acids. The main aim is to simultaneously recover metals and keep sulphuric acid reusable in acid circulation process. From the available literature, the most promising methods were chosen for laboratory experiments. Based on experimental work, the results and observations of electrodeposition, solvent extraction, and freeze crystallization are provided. KEYWORDS Pickling acid, metal recovery, solvent extraction, cathodic polarization, Freeze crystallization. INTRODUCTION Pickling in stainless steel production is an essential surface treatment process (Regel-Rosocka, M. (2010); Agrawal and Sahu, 2009). It is applied for removing surface films such as oxides and chromium-depleted layers to improve the corrosion resistance and surface finish of steel (Regel-Rosocka, 2010). Whilst the process greatly improves the surface finish of the stainless steel, it generates large amount of used acid, containing dissolved metals including chromium, iron, and nickel (Agrawal and Sahu, 2009). Recovery of acid is common practice for most steel producing industries (Nyman and Koivunen, 1986). In this work, acid regeneration process is investigated so as to simultaneously reusing sulfuric acid and recovering the dissolved metals. Recovery of valuable metals even in very small amounts would also bring additional revenue to the steel production industry. At a time when metal production has also been challenged by lack of natural resources for raw materials, secondary sources for metals such as the acid pickling process therefore, have greater potential as supplements. From earlier studies, electrodeposition (Giovanardi and Orlando, 2011; Kuznetsov et al., 200; Rögener et al., 2012; Surviliene et al., 2006), solvent extraction (Alguacil and López 1996; Haghshenas et al., 2009; Kesieme et al., 2013) and freeze crystallization (Beyer et al.,2003; Hasan et al.,2017; Van der Ham et al., 1999) are some of the most established potential methods. Earlier studies have also shown that simultaneous recovery of acid and metals would require combination of different methods. This is primarily due to the nature of very stable metal containing complex compounds formed during pickling. These complexes must be broken down to free the metals for further recovery processes."

Jan 1, 2018

By Muhammad Azeem Raza, Muhammad Zaka Emad, Muhammad Usman Tahir, Saqib Ahmad Saki, Muhammad Usman Khan

Shotcrete is a key initial rock support component used in underground mining and civil projects. The strength of shotcrete plays a vital role in providing and deciding the support adequacy. The strength of shotcrete is evaluated by its uniaxial compressive strength (UCS) test that is usually conducted on extracted core samples. Shotcrete cores are commonly extracted from the test panels along the direction of its application; thus, its strength perpendicular to the direction of application is often neglected. The true bearing strength of shotcrete is thereby ignored despite the fact that higher stresses act normal to the direction of its application. Although the anisotropic behavior of shotcrete is well reported, no study has reported extensive testing of this scale and nature. This study reports extensive testing of shotcrete cores extracted from tunnels of a mega hydroelectric project in Pakistan. The study reports 7- and 28-days strength tests of shotcrete cores. The research also investigates the anisotropic behavior of steel fiber reinforced shotcrete and suggests that shotcrete exhibits higher strength perpendicular to the direction of its application.

Dec 26, 2022

By Deniz Akbay

The strength of rocks and soil is a crucial design parameter in engineering projects, and it can be determined through various test methods such as uniaxial compressive strength, tensile strength, and shear strength. The point load index test is a popular indirect test method for predicting the uniaxial compressive strength of rocks. However, the reliability of the point load index’s estimation of uniaxial compressive strength of rocks is questioned due to the wide range of coefficients that are used to predict uniaxial compressive strength of rocks using point load index values. Factors such as the shape and type of rock specimen, practitioner, and test apparatus used can affect the accuracy of the point load index test. This study investigated the effect of four different specimen shapes used in point load index test (diametral, axial, block, and irregular lump tests) in predicting the uniaxial compressive strength. The rock samples were tested using four test procedures which are called diametral, axial, block, and irregular lump tests. The results showed that the irregular lump test was the most accurate in predicting uniaxial compressive strength, with the highest correlation coefficients and lowest mean absolute percentage errors. The point load index test can be used as a reliable predictor of uniaxial compressive strength of rocks when the irregular lump test is preferred.

Oct 18, 2023

By Md. Z. Quadir, M. Ashraf, A. A. H. Ameri, J. P. Escobedo-Diaz

The quasi-static mechanical response of hot rolled lean duplex stainless steel 2101 (LDSS 2101) in rolling, transverse and normal directions under compression loading has been investigated for its perceived anisotropic behaviour. Microstructural characterization is performed by optical microscopy and Electron Back Scatter Diffraction (EBSD) to qualitatively define the influence of the texture by using Taylor factor and grain sizes, and phase boundaries by utilizing the modified Hall-Petch formula. It was observed that LDSS2101 does not show anisotropic behaviour in terms of the mechanical strength but it has a clear anisotropy in the lateral strains; the microstructural explanation of this response may result from the phase boundaries strengthening.

Mar 1, 2017

By D. Georgiou

Direct sulphuric acid leaching of nickeliferous limonites is the process of choice to recover nickel and cobalt from equatorially located lateritic ores. These ores are rich-in-iron (-45 wt%) existing in the form of goethite enriched with nickel. The merit of this process is due to its high nickel selectivity because of simultaneous iron separation and acid regeneration. Under acid leaching conditions (-250 to 270°C) iron follows an acid dissolution-hydrolytic precipitation path yielding a very low concentration level depending on temperature and acidity of the final leach liquor. The primary precipitation product of iron is hematite which also forms as a scale on reactor internals along with co-existing aluminum. In this paper, an overview of the behaviour of iron solid products under process conditions is made. The evolution of goethite to hematite transformation, as well as the role of iron in reactor scale production, are studied using SEM/EDX characterization techniques.

Jan 1, 1995

By R. Hewer

Transition metals have been widely used in medicine throughout history. The medicinal use of metals extends back to the earliest recorded history when the Chinese used gold as treatment for a variety of ailments. The ancient Egyptians used copper to sterilize water and mercury was reportedly used by Hippocrates in 400BC. Thereafter, numerous other metals have been used as treatment throughout the centuries. For example, zinc sulphate was used as an emetic in the 17th century and zinc oxide was used to treat epilepsy in the 18th century. This use of metals, and numerous other instances, which have been well described in Sneader 2008,1 make for interesting reading but largely occurred prior to the advent of rigorous scientific method. Therefore, although there are exemptions, most therapeutic applications of metals prior to the modern age lack scientific grounding and have been found to be mostly ineffective. Of more relevance are metal-based medicines approved by regulatory bodies (i.e. Food and Drug Administration; FDA) that are in current use as therapeutic drugs. There are presently a large number of metal-based drugs that are approved for use by the FDA ranging from over the counter medicines, such as bismuth subsalicylate for gastrointestinal problems, to prescription drugs such as lithium carbonate for the treatment of manic depression. The list of metal-based medicines approved by the FDA not only incorporates base metals but also includes precious metals. Platinum complexes have been found to be potently active against several different types of cancers while gold complexes have shown application as treatment for rheumatoid arthritis (RA). With the well-established foundation that exists for metal-based medicines, it is imperative to continue exploration into new therapeutic areas. The precious metals; gold, ruthenium and platinum, continue to attract scientific interest in the field of biomedicine and have been widely researched. Scientific studies conducted on gold complexes have demonstrated the potential of this metal for the treatment of HIV/AIDS, cancer and malaria. These diseases are also specific health concerns for developing nations; countries where disease has devastating impact. Within South Africa alone, an estimated 5.7 million people are infected with HIV/AIDS,2 approximately 7 000 new cases of malaria are reported annually, and it is projected that 1 in 4 persons will develop cancer. Continuous development of therapeutic drugs to combat these diseases is therefore apriority, and the exploration of gold-based compounds for this purpose is warranted.

Jan 1, 2009

By Tristan H. Jones

Rib-related accidents in underground coal mines continue to cause injuries and take lives at a rate of 1.3 fatalities per year for the last 17 years. Prevention of these accidents cannot simply be a matter of installing more rib support, though the eventual final solution will undoubtedly include that component. Ultimately, rib safety will be brought about through an understanding of the causes and mechanisms that cause rib fatalities, and by fine-tuning mining methods and procedures that are currently in place. This paper investigates the factors likely to be most influential in the occurrence of rib fatalities. A careful analysis has been conducted of the rib fatality reports documented by the Mine Safety and Health Administration between 1996 and 2013. The primary outcome is the determination of the relative impact of each type of rib fatality factor and a better understanding of the impact each factor has. Among the rib fatality factors considered, the influence of rib profileis considered for the first time. Mining height, rib stratigraphy, mining cycle, and the standing position of a miner next to a pillar are also considered. Questions are also raised about the current interpretation of rib fatalities due to mining depth, with the indication being that mines operating at the greatest depths may actually have the most respectable rib fatality record among all mining depths. Additionally, a new method of considering rib exposure is developed. Based on the results, recommendations are made for future work. By gaining a better understanding of how particular factors contribute to rib fatalities as opposed to rib failure or stability, it is hoped that future efforts can be more precisely directed towards the desired outcome of fatality reduction.

Jan 1, 2014

By David Hanson, Sean Warren, Chaparral Berry

"Coal bumps, also referred to as dynamic failure events or coal bursts (Lawson, Weakley, and Miller, 2016), continue to be a hazard in underground coal mines. While current design methods have significantly reduced the occurrence of coal bumps, they have not been completely eliminated. This paper investigates a correlation between coal compositional components, coal molecular structure, and probability of coal bumps in an effort to deepen understanding of coal behavior in an effort to reduce hazards in underground coal mines.Samples from the Penn State Office of Coal (PSOC) Department of Energy Coal Samples (DECS) were obtained for Fourier Transform Infrared Spectroscopy (FTIR) analysis using the KBr pellet method. Peaks indicative of the coal molecular structures were obtained using spectral integration software. These data, combined with published elemental data, were compared to historic bump occurrence in order to establish a possible correlation. Finally, results based on multivariate analysis of the elemental and FTIR data with bump status as the dependent variable suggest that elemental sulfur and molecular structure can be used as an indicator of bump susceptibility within the sample set considered.INTRODUCTIONThe study of coal requires consideration of multiple variables: percentages of organic and inorganic components, organic component origins, coal age, pore structure, cleat density, elemental composition, etc. Examining coal in situ increases the number of variables, such as coal depth, seam thickness, surrounding stratigraphy, and so forth. This collection of variables influences the subsequent behavior of coal simultaneously, and weighing their relative impact is a challenge for researchers. “A problem never exists in isolation; it is surrounded by other problems in space and time” (Ackoff, 1956). Having a substance such as coal that we know so much about, and yet so little, we have to ask what can be learned.An experimental study using Fourier Transform Infrared Spectroscopy (FTIR) was undertaken to determine if the chemical structure of coal contains information which may lead to a better understanding of triggers or attributes which may, in turn, lead to an increased probability of a dynamic failure event. While a full analysis of the factors driving dynamic failure are beyond the scope of this study, it is possible that a better understanding of the chemical structure of coal will lead to an increased knowledge of its inherent behavior, including its propensity to burst."

Jan 1, 2019

By M. Mathiba

High CO2 fluxes associated with reclaimed coal mine spoils pose an environmental hazard where such sites are used for building. CO2 concentrations in excess of 25% have been reported in homes constructed on or down gradient of such spoils. The objective of this study was to investigate the effect of a mitigation trench used at one mine site on CO2 fluxes across the trench using chamber?based trace gas measurement. LI8100 automated CO2 flux system was used to measure CO2 fluxes from 32 sample points located across a deep mitigation trench on June 8 and 9. The maximum recorded fluxes were 7.29 and 8.18 µmol/m2/s, with averages of 4.15 and 5.50 µmol/m2/s, up and down-dip respectively. These preliminary results show CO2 flux is higher up-hill than down-hill at 95% significant level. This work shows that flux measurement can be used to investigate CO2 migration on reclaimed mine land. Further work is necessary to allow geostatistical modeling of the spatial variability of CO2 fluxes over reclaimed coal mine spoils. Knowledge gained would assist mining practitioners and regulators in reclamation planning for envisaged post-mining land uses.

Jan 1, 2010