Search Documents

By Hans E. Madeisky, Bruce W. Downing

The acid rock drainage (ARD) buffering capacity of mine waste is governed by its bulk chemical composition and its mineral assemblage. Conventional acid base accounting (ABA) tests can be used to predict short-term buffering, but should be used with caution to model or predict the long-term ARD buffering capacity of mine waste. ABA data for mine waste samples from four different deposit types: an orthosite-hosted magmatic sul?de nickel, dunite-hosted magmatic sul?denickel, porphyry copper-gold, and volcanic-hosted high sul?dation epithermal silver, were compared with whole-rock geochemical and petrographic data obtained from the same samples. Our objective was to devise and test a method of predicting ARD buffering capacity based on bulk chemistry and modal mineralogy. In other words, we developed a quantitative theoretical method for calculating neutralizing potential, relying on easily obtainable and relatively inexpensive whole-rock and sulfur XRF analyses, which could substitute for conventional ABA procedures in situations where these procedures are either too costly or too time consuming. For each deposit type, models were devised that reasonably approximate the net neutralization potential estimated by the ABA data obtained from laboratory tests. Once an appropriate model has been developed and tested, portable X-ray ?uorescence equipment, already used for grade control at many mine sites, could provide the whole-rock and sulfur analyses required to estimate the ARD potential of the waste material. Although this approach is not intended as a substitute for the legally mandated ABA test procedure, it could facilitate the timely and cost-effective management and mitigation of ARD at a mine site.

Jan 1, 1997

By L. K. Mireku

"Abstract - The Halfmile Lake South Deep zone, Bathurst Mining Camp, New Brunswick, was discovered by Noranda Inc. (Exploration) as a result of a 3-D seismic survey in 1998 and the subsequent drilling of ten diamond-drill cores. The deposit consists of massive, breccia, and stockwork Pb-Zn-Cu sulfide minerals, and is hosted by a volcano-sedimentary sequence belonging to the overturned Ordovician Tetagouche Group. Epiclastic rocks and interbedded fine-grained felsic pyroclastic rocks dominate the stratigraphic footwall. Locally, crystal-rich felsic tuffs and subordinate epiclastic rocks comprise the immediate stratigraphic hanging wall. The entire stratigraphic sequence was intruded by quartz-feldspar porphyritic intrusions, and cut by intermediate and basic dikes. The volcanic and sedimentary rocks can be discriminated geochemically using trace element ratios such as Zr/TiO2 and Nb/TiO2, despite intensive alteration and cleavage development. These ratios indicate that four protolith volcanic compositions exist: rhyolite, dacite, andesite, and basalt. The aphyric and feldspar- and quartz-phyric volcanic rocks are dacitic and rhyolitic in composition; epiclastic rocks have trace element ratios consistent with dacitic compositions. Pearce element ratio diagrams, general element ratio diagrams, and petrographic observations demonstrate that the rhyolitic volcanic rocks exhibit evidence of albite, potassium feldspar, and quartz fractionation, dacitic volcanic rocks exhibit little evidence of any fractionation, and epiclastic sedimentary rocks exhibit evidence of quartz sorting only. Hydrothermal alteration is best represented by the presence of phengitic muscovite and daphnitic chlorite. Minor calcite occurs in the stratigraphic hanging wall, deep in the stratigraphic footwall, and in post-mineralization dikes, and thus is not interpreted to be part of the causative hydrothermal event. Element additions and losses during alteration have been used to determine net alteration reactions, and these have been used to identify alteration parameters that are independent of other forms of alteration and fractionation/sorting, and which can be used to guide exploration. These parameters include: a bulk hydrolysis measure, (2Ca+Na+K-2CO2)/Al; a muscovite alteration measure, K/Al; an albite destruction measure, Na/Al; a chlorite alteration measure, (Fe+Mg-S/2)/Al; a chlorite composition measure, (Fe-S/2)/Mg; a sulfidization measure, S/Ti; and a carbonatization measure, CO2/Ti. With the exception of the carbonatization measure, these alteration parameters define a distinct lateral and vertical zone of intense hydrothermal alteration in the stratigraphic footwall of the deposit, and demonstrate that the epiclastic rocks are predominantly chlorite altered, and the volcanic rocks are predominantly muscovite altered. Within the alteration halo, element additions of Fe and H, and element losses of Na are characteristic. Potassium was added to muscovite-altered rocks, but subsequently removed from chlorite-altered rocks. The results from this study demonstrate that metamorphism and deformation have not significantly obscured hydrothermal alteration signatures."

Jan 1, 2006

By Michel Mellinger

This paper presents preliminary results of a project aimed at obtaining a better understanding of the genesis of gold mineralization in northern Saskatchewan using lithogeochemistry. The properties sampled were: Weedy Lake (B Zone), Waddy Lake (Komis Zone) and Wedge Lake (Twin Zone) in the La Range belt, and the Rio mine in the Flin Flon area. Although the three vein-type deposits rudied here (Weedy Lake. Waddy Lake, Rio deposit) occur in different geological situation . a common gold deposition mechanism appears to have been active at all three location . Hydrothermal fluids carrying sulphur in solution in exces of gold thio-complexes moved through fractured host-rocks until they reached a site where pyrite precipitation wa triggered. As pyrite precipitated, the a/ aAu activity ratio of the fluid decreased. until a critical thre hold was reached and gold thio-complexe were de tabilized . resulting in the co-precipitation of gold and pyrite. The conditions triggering the precipitation of pyrite appear to have been: the abundance of iron in host-rock ~ilicates at Waddy Lake. and temperature decrease upon the reaching of structural trap~ at both Weedy Lake and the Rio deposit. with additional involvement of carbonatizationrelated reactions between fluid and host-rocks for the latter. In addition to pyrite precipitation , potassic alteration of the mafic metavolcanics is observed at Waddy Lake. while at the Rio deposit, the extensive carbonatization of the host-rocks i coupled with the deposition of chlorite that may have been remobilized from the altered mafic host rocks. In both the B Zone at Weedy Lake and the Komis Zone at Waddy Lake, a di tinct vanadium signature give some clue about the direction in which the hydrothermal fluids have moved . and the interpretation made is con istent with the geological ituation in either case. As for the Wedge Lake deposits, the distinct base metals-precious metals a sociation within a sulphide-facies iron formation confirm the volcanic exhalative origin of this gold mineralization .

Jan 1, 1986

By Jr. Abel

Subsidence is controlled by a complex combination of mining and geologic factors. For example, a world-wide compilation of data shows that, as the percentage of shale in the overying rock mass decreases and the amount of sandstone increases, the angle of draw (and the area affected by subsidence) decreases. Limestone in the overburden appears to cause as much as a three-fold decrease in the angle of draw compared to a like amount of sandstone. Increased amounts of sandstone were accompanied by a greater surface subsidence relative to the mining height. The total thickness of overburden did not appear to influence the subsidence magnitude above super-critical panels. The greater the thickness extracted the smaller percentage of that thickness that shows up at the surface as subsidence. The greater the percent of the seam extracted, the greater the subsidence reaching the surface. The maximum subsidence above room and pillar panels is dependent on the pillar height and minimum width as well as the other factors listed.

Jan 1, 1980

By Pierre J. Goossens

Since Guild 1 and Snelgrove 2 attracted our attention to the relationships between certain endogenic ore deposits and plate boundaries, an abundant flow of papers appeared in the metallogenic literature concerned with this problem and its application to mineral exploration. Some of the papers only speculate with the formation of specific type of ore deposit 3, 4, 5, 6, 7, 8, 9, 10, 11, 12 Other papers are more concerned with genetic and structural relationships between plate tectonics and mineralization 13, 14, 15, 16, 17, 18, 19, 20 They are philosophical, in that they are generalized and refer to no specific area. Yet it is true that a large part of the world mineral potential is concentrated at the convergence of oceanic and continental plates, for example, around the Pacific. Therefore, the interaction of two plates by either subduction, obduction or slippage likely has an important role for the genesis and/or the (structural) control of these "orogenic" ore deposits. If subduction is the driving mechanism for the generation of igneous rocks 21, 22 and endogenic ore deposits 18, volcanic activity and the nature of volcanic products certainly are the major geologic processes and events to be tested. Fonteilles 23 and Alsac 24 have already emphasized the important relationship between mineralization and the talc-alkaline affinity of the volcanics. The Andean orogen is one of the best areas for testing such genetic relationships. Rich and varied endogenic and volcanogenic ore deposits occur there and plate interaction is still active.

Jan 1, 1975

By Luc Harnois, Gabriel Voicu, Marc Bardoux, Robert Crépeau

"Abstract-Detailed petrographical and geochemical studies have been carried out on the igneous and sedimentary rocks in the Omai area, part of the Paleoproterozoic Barama-Mazaruni greenstone belt, Guyana. The stratigraphic succession at Omai begins with basalts, associated with mafic-ultramafic intrusives and poorly-sorted conglomerates; these are overlain by andesites and quartzfeldspar porphyries, with pelites and tuffaceous sediments at the top. The volcanic-sedimentary succession was intruded by a quartz-monzodioritic stock (Omai stock) and granophyric rhyolite dikes. Several generations of mafic dikes were intruded discontinuously from the Mesoproterozoic to the Permo-Triassic. Volcanic rocks range in composition from subalkaline basalt to high-silica rhyolites, with a gap between 60% to 70% SiO2, which suggests the suite is bimodal. Major, trace, and rare earth element criteria were used to subdivide the rocks into tholeiitic and calc-alkaline types. The tholeiitic rocks are characterized by flat to moderately sloping chondrite-normalized REE patterns. On the basis of immobile trace-element ratios, the tholeiitic mafic rocks from Omai have characteristics of immature intra-oceanic island arcs, or of E-MORB basalts affected by a strong arc signature, as is commonly reported for back-arc basin basalts. The andesites, quartz-feldspar porphyries, rhyolites and quartz monzodioritic stock are calc-alkaline, with strongly sloping REE patterns, enrichments in the large-ion lithophile elements, and depletions in the heavy REE and high-field-strength elements, features which are typical of more mature island-arc settings.At Omai, two types of gold-bearing veins can be distinguished: vein sets (± stockworks) and tension veins, both post-dating the regional metamorphic peak at the level they were emplaced. The relationship between the gold mineralization and its host lithologies does not seem to be genetic. Rather, the emplacement of mineralization was strongly influenced by the rheological contrasts between the intrusive/subvolcanic bodies and the volcanic/sedimentary country rocks. These contrasts helped to focus the regional stress upon the more competent intrusive subvolcanic bodies, resulting in brittle fracturing, and therefore in greatly enhanced permeability to hydrothermal fluids. The Omai gold mineralization can be classified as late tectonic, with its emplacement controlled by the last brittle to brittle-ductile stages of the Trans-Amazonian orogeny."

Jan 1, 1997

By Gabriel Voicu, Harnois Luc, Marc Bardoux, Robert Crépeau

"Detailed petrographical and geochemical studies have been carried out on the igneous and sedimentary rocks in the Omai area, part of the Paleoproterozoic Barama-Mazaruni greenstonebelt, Guyana. The stratigraphic succession at Omai begins with basalts, associated with ma?c-ultrama?c intrusives and poorly-sorted conglomerates; these are overlain by andesites and quartz-feldspar porphyries, with pelites and tuffaceous sediments at the top. The volcanic-sedimentary succession was intruded by a quartz-monzodioritic stock (Omai stock) and granophyric rhyolitedikes. Several generations of ma?c dikes were intruded discontinuously from the Mesoproterozoicto the Permo-Triassic. Volcanic rocks range in composition from subalkaline basalt to high-silicarhyolites, with a gap between 60% to 70% SiO2, which suggests the suite is bimodal. Major, trace, and rare earth element criteria were used to subdivide the rocks into tholeiitic and calc-alkaline types. The tholeiitic rocks are characterized by ?at to moderately sloping chondrite-normalized REE patterns. On the basis of immobile trace-element ratios, the tholeiitic ma?c rocks from Omai have characteristics of immature intra-oceanic island arcs, or of E-MORB basalts affected by a strong arcsignature, as is commonly reported for back-arc basin basalts. The andesites, quartz-feldspar porphyries, rhyolites and quartz monzodioritic stock are calc-alkaline, with strongly sloping REE pat-terns, enrichments in the large-ion lithophile elements, and depletions in the heavy REE and high-?eld-strength elements, features which are typical of more mature island-arc settings.At Omai, two types of gold-bearing veins can be distinguished: vein sets (± stockworks) and tension veins, both post-dating the regional metamorphic peak at the level they were emplaced. The relationship between the gold mineralization and its host lithologies does not seem to be genetic. Rather, the emplacement of mineralization was strongly in?uenced by the rheological contrasts between the intrusive/subvolcanic bodies and the volcanic/sedimentary country rocks. These con-trasts helped to focus the regional stress upon the more competent intrusive subvolcanic bodies,resulting in brittle fracturing, and therefore in greatly enhanced permeability to hydrothermal ?uids.The Omai gold mineralization can be classi?ed as late tectonic, with its emplacement controlled by the last brittle to brittle-ductile stages of the Trans-Amazonian orogeny."

Jan 1, 1997

By V Salamakha, K Tang, G Si, J Oh, X Wu, Z Yu

The development of machine learning (ML) algorithms has led to promising advances in lithology classification from geophysical logs, which is indispensable in various underground engineering applications. Due to the resolution and availability of logging data, ML models can recognise lithology change in a definitive form at a fine scale (0.01 m). While the results from previous models indicated promising performance in the classification, the robust capability of generalising lithology prediction to unseen data may not be true for those models due to: (1) data bias caused by borehole selections, and (2) logging data mismatches among boreholes. To this end, this paper aims to investigate the generalisability of ML models and seek potential improvements. Four ML models were selected to be trained on single reference boreholes to test the other (as unseen) in the same region, which includes Support Vector Classifier (SVC), Random Forest (RF), eXtreme Gradient Boosting (XGBoost) and Residual Neural Network (ResNet10). The data set involves 11 boreholes from a coalmine in north-western Bowen Basin (Queensland, Australia): density, gamma ray, neutron, and sonic logs are selected as inputs. Additionally, a data adaptation method is applied for better generalisability. The results show that there is an accuracy trade-off between the same borehole and unseen boreholes across the models. It also indicates a 16–43 per cent reduction in model performance when generalising the predictions (in marco-F1 score), while the adapted data sets can contribute to a around 12 per cent improvement. This study provides a fundamental understanding of the model generalisability when using a single borehole, essential for further correlating boreholes for regional lithology classification; the adaptation method can improve the generalised accuracy, and reduces the labour to label lithology, which facilitates the identification of gas storage mechanisms, geological/geophysical modelling, and stratigraphic analysis.

Sep 1, 2024

By Thon T. Gin

The lithologic, mineralogic, and magnetic beneficiation characteristics of the iron formation at U. S. Steel's Atlantic City Ore Mine, Fremont County, Wyoming, have been determined. The iron formation averages about 30 percent Fe content, and varies from 125 feet to about 500 feet in thickness. It is composed of interbedded magnetite-rich quartzites, magnetite-quartz-amphibole schists, and amphibole-chlorite schists. Quartz, actinolite-tremolite, chlorite, and magnetite are the essential mineral constituents. These rocks are differentiated into four major ore types on the basis of their relative quartz and amphibole content. The iron content of the magnetic concentrate decreases and the silica content increases with decreasing grain size and increasing amphibole content in each ore type at the same fineness of grind. Criteria were developed to enable the mine operator to recognize the ore types and to blend them to produce a more uniform concentrator feed. This results in less variation in product quality and requires fewer changes in operating conditions-in the concentrator.

Jan 1, 1965

Potassic alteration domains of greenstone belt lode gold deposits are characterized by systematic partitioning between different groups of incompatible elements, such that Al, Ga, Th, U, Ti and V are decoupled from K, Rb, Ba, Cs and Tl. The former group of elements have concentrations and interelement ratios in alteration domains which reflect host rock control, implying approximately isochemical behaviour. In contrast, K, Rb, and Ba are strongly coenriched, and linearly correlated over th4ee orders of magnitude in abundance, where K/Rb = 260, and K/Ba = 40: K/Cs (-10 ) and K/T1 (-2x10 ) are also correlated, though more weakly. Lithium abundances, and Rb/Sr ratios are erratic in altered rocks. These interelement trends, collectively, are present in deposits variously hosted by ultramafic, mafic, or felsic volcanic rocks, and sediments or granitoids.

Jan 1, 1988

By Alan A. Barton

Introduction The Little Long Lac mine is situated in the Thunder Bay mining district, township of Errington, Ontario. The mine is located on the south side of the most westerly bay of Little Long Lac. The property consists of 36 claims, which comprise some 1,400 acres. This group of claims was staked in August, 1932, by Tony Oklend and Tom Johnson, and, after surface sampling, was optioned by the present controlling interests, who diamond-drilled it during the winter of 1932-33. In early spring, a small steam-driven plant was installed, and shaft sinking commenced on June 1st, 1933. During the summer, all supplies are transported to the mine from Hardrock station, at mileage 18 on the Canadian National Railway line from Longlac to Port Arthur. At Hardrock, which is seven miles from the mine, the railway skirts a bay of Little Long Lac, and supplies are loaded directly from railway cars to scows. Two scows are used, of 30-and 45-ton capacity, respectively. A 36-ft. pointer, powered by a 35 h.p. engine, is used as a tug. A good winter-road has been cut out from Geraldton to the mine, for winter transportation. Geraldton is about two miles north of the mine, and is also located on the Canadian National railway. A hard-surface road is now being constructed for summer as well as winter use. Geology The Little Long Lac gold area covers the northern limits of a large synclinal structure, the contact of the Keewatin flows and sediments, striking about twenty degrees north of west, with the dip of the sediments varying from eighty degrees north to seventy degrees south, the average being around eighty degrees south. The vein worked by Little Long Lac Gold Mines occurs in massive sedimentary rock of about the composition of arkosic or quartzitic greywacke, and consists of a shear-zone up to fifteen feet in width, striking N.75°E. and dipping steeply to the south, which has been filled by numerous narrow, parallel quartz veins and. veinlets. These are well mineralized. with arsenopyrite, pyrite, and some chalcopyrite and stibnite, and carry considerable quantities of visible gold. They show more than one age of quartz deposition, the quartz being fractured and re-cemented. The arkosic rocks separating the veins and veinlets are also slightly mineralized with pyrite. Work to date has indicated the probability that the vein-shear is controlled by local drag-folding.

Jan 1, 1935

By J Schrank

Double-stack trains in the United States date back to the early 1980s, starting about the time deregulation of the rail industry occurred. Freight rail became increasingly more competitive to trucking and barge or ship, and led to major investments in railroad infrastructure. Since most railroad tunnels in the United States were constructed between 1880 and 1930, they were not built tall enough to accommodate modern double-stack intermodal railcars. Therefore, as double-stack trains became the norm, existing tunnels became bottlenecks, and railroads wanted the tunnels made larger without impacting traffic. This need to increase the clearance while not impacting rail traffic launched a very specialised industry: the design and construction of replacement lining systems in existing tunnels.Several large multitunnel railroad clearance improvement projects have been completed in the country in the last decade, and they have all been done under ‘live track’ conditions. Live track conditions consist of work windows, often anywhere from four to 12 hours, that are provided to the contractor to complete the construction work. By the end of each work window, the tunnel must be secured so that the railroad can run trains.In addition to improving the clearance, these projects provided the railroads with an opportunity to improve the general condition of the tunnels, including structural, seepage, drainage and icing conditions. This paper discusses the design considerations, tunnel assessments and construction methods used for these live track railroad tunnel projects. Seepage and drainage improvements that were incorporated into the clearance improvement projects are also discussed.CITATION:Schrank, J, 2014. Live track railroad tunnel repair and clearance improvement in the United States, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 619–628 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By Warnett Kennedy

"GENUINE CONCERN for the environment is a built-in attitude of mind. If you do not have it by age 40 you probably never will. Some people speak the jargon of 'environment' and 'ecology' for political reasons, others because it feeds their need and bias toward attitudes of moral indignation or dissent. Others pay lip-service for purely business reasons. Complete reactionaries equate conservationists, ecologists and environmentalists as either 'commies' or 'pinkos'. Their real credo is the old saying, ""Where there's muck there's brass."" Those who have genuine concern for good environment are not only romantics like Thoreau but realists who sense the danger to our planet if human greed is rampant and unchallenged. The cities are in real trouble. Almost 75 per cent of the population already live in and around cities. Even mining men live in cities or bring up their children in the new 'instant' towns. The ecology of cities is the concern of all. Our distinguished guest Stewart Udall, in his book ""The-Quiet Crisis,"" quoted Thoreau in 1859 as having written ""each town should have a miniature wilderness park, a primitive forest of five hundred or a thousand acres where a stick should never be cut for fuel, a common possession forever."" Mr. Udall will be glad to know that this advice was taken in at least one instance known to me. I refer to Stanley Park in Vancouver. It is a primitive forest of 1000 acres right inside our small downtown peninsula. It remains unmanicured. This month we celebrated the completion of a seawall of 4%, miles along its perimeter. The construction of this wonderful walkway started in 1910. We are very, very proud of our park."

Jan 1, 1972

By E. R. DeMen

In late 1965 General Mills announced the availability of a new liquid ion exchange reagent, LIX®-64, for the recovery of copper from various solutions, such as dump leach liquors. Acceptance of this material by the copper industry has been gratifying. A number of pilot plants have been operated, and at this writing there are four commercial plants either in operation or under construction. The properties and operating characteristics of this reagent have been described in previous papers.1,2 LIX-64 is quite effective and selective for copper extractions although partially limited in pH ranges, losing extraction efficiency as the acidity of the feed solution increases to below pH 1.0. Also, the LIX-64 content in the kerosine carrier was limited to about 10 volume percent (except for special cases) because of rapidly decreasing phase disengagement rates above this content. This in turn led to large plant capital costs, as the organic flow rates had to be in- creased (rather than LIX-64 content) to extract the copper from high content liquors. This was true in all circuits where the feed copper content ran above 2.0 g/l copper. A reagent was needed which would extract copper from more acidic liquors (or higher copper content liquors) and which exhibited improved phase disengagement characteristics with reagent contents up to 30 volume percent. General Mills is pleased to announce the availability in commercial quantities of a new and improved reagent, L+-64~. This reagent broadens the pH range in which copper can be extracted, and exhibits superior phase disengagement characteristics. The improvement in the reagent has been noted in laboratory circuits, as well as pilot plant runs and commercial operations.

Jan 1, 1970

In early 1970, General Mills Chemicals, Inc. announced the availability of en improved liquid ion exchange reagent, LIX® 64N, for the recovery of copper from various solutions, such as dump leach liquors. LIX 64N has been shown to be a considerable advance over LIX 64, and is presently in use in three commercial plants. Results have been very gratifying. For example, one of the plants was designed for operational production of 40,000 pounds copper per day, and in fact reached this output within the third week following startup of the plant. In addition to the operating plants, another is scheduled to come on stream this month with L D( 64N being used to extract and recover both copper and nickel. The chemical properties and operating characteristics of this reagent have been fully described in a previous paper. 1 LIX 64N is quite an effective and selective extractint for copper, even with copper contents as high as 15 g/l, but the reagent is somewhat limited in pH range, and loses some of its extraction efficiency as the pH drops below 0.8. Liquors derived from vat leaching, electrolytic tankhouae bleed streams, or some of the new leach schemes derived to solubilize copper from sulfide concentrates are examples of the liquors that present major problems when treated via liquid ion exchange. LIX 64N could extract some of the copper from such streams, but recovery was limited to about 75 percent. Also, in some parts of the world there are streams which are relatively low in copper (-5 g/l) but which are very high in acid (25-50 g/1 H2SO4). Again, LIX 64N can attain only about 75 percent recovery from such streams. For effective treatment, these streams require a reagent which will maintain the excellent selectivity of LIX 64N, and will

Jan 1, 1971

By D. W. Agers

This paper is an extension of previous work evaluating a new extractant, LIX®-64, for recovery of copper from dilute acidic solutions. Large scale pilot plant operations have confirmed the technical and economic feasibility of the process and, with minor exceptions, scale up parameters obtained by previous laboratory work. Operating problems encountered in the pilot plants are discussed. Design parameters for-scale-up to commercial plants are presented and discussed along with a revised capital cost estimate. The future pilot program is discussed, including minor design changes and the effect of entrained organic on dump leaching efficiency.

Jan 1, 1967

The Autogenous milling of ores holds an increasing attraction as the focus moves towards reducing energy usage, both direct and embodied in grinding media. However, most of the early AG mills were converted to SAG for improved stability and increased throughput. This imposes a huge penalty in steel grinding media consumption. The LKAB iron ore operations in Sweden process highgrade magnetite through fully-autogenous milling lines to a final product P80 of about 45µm. The outcomes of P9O AMIRA research surveys, covering a wide range of mill fillings and throughputs and with different feed blends, are presented. Insights are provided on operational strategies, opportunities, the influence of feed size control and balancing the blend of competent gangue and softer magnetite. Areas of importance in the successful operation and control of energy-efficient autogenous circuits are highlighted.

Jan 1, 2012

By Martti E. Maliniemi

The Svappavaara mine is located 47 km southeast of Kiruna C. The ore deposit now being worked, Leveäniemi, belongs to Luossavaara- Kiirunavaara AB (LKAB) and is the company's, and also Sweden's, third biggest mine after Kiirunavaara and Malmberget. The distance by rail to the Norwegian port of Narvik is 214 km and to Lulei on the Gulf of Bothnia 340 km (Fig. 1). The village of Svappavaara has about 800 inhabitants. The climate is arctic in character. The temperature during the months of December to February is about -20º to -35ºC, and the ground is covered by a blanket of snow for about eight months of the year. The brief, intensive summer often arrives with startling speed, bringing both sunshine and warmth. HISTORICAL BACKGROUND Mining operations took place in Svappavaara as far back as 300 years ago. During the period 1655-1684, copper ore was taken from the deposit called Gruvberget in the vicinity of the village. The total production of raw copper was probably about 1,045 tons. During the 18th and 19th centuries, several attempts were made to extract iron ore from the numerous deposits found within the district. These brave attempts, however, were foiled by the high phosphorus contents and the enormous transport difficulties. The present-day mine fields in Leveäniemi were discovered in 1897. At that time, it was difficult to determine the size and value of the deposit because of the thickness of the soil cover (3 to 15 m) and the

Jan 1, 1969

By Silas C. Nichols, Jennifer E. Nicks

"Limit states design (LSD), or load and resistance factor design (LRFD), is a method to account for the uncertainty in loads and resistance through a reliability calibration that requires all applicable limit states (strength, service and extreme) to be checked during foundation design. LRFD has been in use internationally for several decades; however it wasn’t until recently that engineers working on highway projects were required to use the method for the design of highway bridges and other appurtenances. Although the bridge community has been using a form of limit states design for structural components since the early 1970s, the design of foundations for bridges, walls and other geotechnical features had long been performed using allowable stress design (ASD), whereby all uncertainty in loads and material resistance is combined in a single factor of safety. While the move to LRFD was viewed as a more rational approach for the design of bridges and structures, the transition to its use for geotechnical engineering has been met by many with confusion and difficulties in application. This article will revisit the history of transition from ASD to LRFD for geotechnical engineering, summarize the status of the transition and issues with its use, and briefly discuss some emerging research opportunities for improving and advancing the design platform.Background and HistoryUntil about a decade ago, foundations and substructures for bridges were traditionally designed using ASD, while the superstructure was designed using load factor design (LFD), a precursor to LRFD that incorporated factored design loads but no risk assessment. This combination led to uncertain and incompatible safety margins in design for the various bridge components. In 1986, the American Association of State Highway Transportation Officials (AASHTO) Subcommittee on Bridges and Structures (SCOBS) concluded that the standard bridge specifications in use at the time for U.S. transportation projects had significant inconsistencies and gaps, wasn’t up to date with emerging technology and that the development of new specifications was warranted. The proposed solution by the subcommittee was to transition to a more coherent method of design where applicable failure and serviceability conditions could be evaluated considering the uncertainties associated with loads and resistance."

Jan 1, 2015

By T. M. Klemetti, T. J. Batchler, T. J. Matthews

"From 2011–2016 there were 1,511 documented injures, including 7 fatalities, from ground falls in U.S. underground coal mines. The majority of these ground fall injuries were not caused by a major roof collapse, but from falls of smaller rocks from the immediate roof. Roof screen can significantly reduce the number of these injuries and has been widely utilized in underground coal mines for surface control. Because of the potential of reducing ground-fall injuries, the National Institute for Occupational Safety and Health (NIOSH) is further evaluating the performance characteristics of welded wire screen as used in underground coal mines by conducting a laboratory testing program at the Mine Roof Simulator (MRS) in Pittsburgh, PA. The load-displacement characteristics of a 2.4-m x 3.7-m panel of 8-gauge welded screen were evaluated using a newly designed, large laboratory screen test frame with multiple load pull locations. This screen was tested in a configuration that simulates current installation practices in U.S. coal mines. In this study, the effects of displacement loading rate, load pull surface geometry, and the inclusion of roof channel on the screen performance were evaluated. Ultimately, the type of information obtained in this and similar studies can be used to aid in developing wire roof screen design criteria and to assist mine operators in the selection and use of roof screen in underground mines. INTRODUCTION Over 1,500 injures, including 7 fatalities, occurred from 2011–2016 from ground falls in U.S. underground mines with the majority of these ground-fall injuries caused by falls of smaller rocks from the immediate roof. Various controls are currently being used in mines to control this surface rock, including the use of wire roof screen. In mines where wire roof screen has been installed, injuries from rock falls have been reduced dramatically (Robertson and Hinshaw, 2001). Roof screen has the potential to prevent hundreds of injuries caused by the fall of small rocks between permanent roof supports (Comptonet al., 2007). Because of this potential for reducing ground-fall injuries, the National Institute for Occupational Safety and Health (NIOSH) is evaluating the performance characteristics of welded wire screen as used in underground coal mines by conducting a laboratory testing program at the Pittsburgh Research Laboratory (PRL)."

Jan 1, 2018