Search Documents

By D. M. McFarland

A FEW years ago a novel electric detonator known as the split-second or millisecond delay electric blasting cap was introduced for use in quarry blasting. Regular electric blasting caps fired in series may be depended upon to fire within a millisecond or so from the first to the last in a series. Regular delay electric blasting caps are provided that fire one period after the other period in intervals of 1/2 to possibly 11/2 sec. Most split-second or millisecond delays are designed to fire one period after the other period in possibly 25 to 50 millisecond intervals. The ear is not capable of detecting time intervals of this magnitude. The primary thought at the time millisecond delays were introduced was to investigate the results on rock breakage by firing a line of holes in a quarry face so that charges in adjacent holes would not be detonated simultaneously. This could not be accomplished satisfactorily with regular delays. The time interval between successive periods of 1/2 to 1 sec was sufficient to permit considerable movement of the burden. If the burden of one hole was reduced to a great extent by the firing of an adjacent hole, the firing of the hole with the reduced burden would likely reveal this lack of confinement by a terrific report and wild throw of rock. In the early blasts with millisecond delays it was observed that instead of the usual sharp report, the blast had a muffled sound and vibration was not as perceptible as when simultaneous firing was used. Because many quarry operators were being threatened with injunctions or suits for damages by neighbors who claimed structural damage to their buildings, millisecond delays were tried extensively in quarries. In the majority of these trials, the results were very satisfactory. The seismologists recorded the ground movement created by many blasts and verified the initial observations that millisecond delays could be used to reduce vibrations appreciably. In the past few years the advantages of this principle of nonsimultaneous firing of the charges in blasts has become generally accepted. Today the quarry operator who has vibration troubles, inadequate breakage, and excessive backbreak and has not investigated the possibilities of millisecond delay blasting is ignoring a remedy that has proved satisfactory for many. His complacency may be costing him money. Because of the results attained in quarry blasting, it was logical that millisecond delays should be tried in construction work such as in road cuts. As formations in this type of work are likely to change rapidly with advance of the cut, it is more difficult to evaluate results than in quarry blasting. However, this improved control over timing has been beneficial in limiting throw, promoting fragmentation, and reducing overbreak. In blasting near buildings the reduction in vibration and in throw has been especially helpful. As blasters employed in construction work learn what may be accomplished by closer control over the time of firing of explosives charges, more and more millisecond delays are being used to supplant instantaneous electric blasting caps. Improved Fragmentation Underground With this background of promising results, it was not surprising that millisecond delays should go underground. In limestone mining use of millisecond delays as compared with use of cap and fuse or electric blasting caps showed improved fragmentation in stopes and in slabbing operations. Then an opportunity developed to use millisecond delays in some tunnels being driven in a limestone mine (fig. 1). Using the normal charge employed and merely substituting three millisecond delay periods for three regular delay periods, there was a noticeable difference in the appearance and the position of the pile of rock after a blast. A greater portion of the face was exposed, the crest of the pile was farther from the face, and the pile was heaped high along the center line of the tunnel leaving room to walk along the ribs to the face. Fragmentation was appreciably increased. It gave the impression that the slabs had been thrown against each other with tremendous force, promoting the movement of the broken rock along the center line of the tunnel away from the face. Because the drilling and the charge weights were unchanged, the evidence was convincing that the difference in timing was responsible for the difference in results. Probably a greater portion of the energy from the explosives had been expended in doing useful work on the rock. Zeros followed by two periods of millisecond delays were used in the V cut and in two slabs to either side of the cut in this simple round. When millisecond delays, substituted period for period for regular delays, are first tried in a drift round in a mine, and the usual charge of explosives

Jan 1, 1951

By W. S. Row

This mine is operated at 4000 to 4500 tons daily through a single shaft, with one rock hoist and one senice hoist. Latest shaft construction is concrete with wooden dividers. Economics of drifters and air-leg drills are compared, as well as costs of shrinkage and sub-level stoping. Economy of large haulage equipment and underground crushing is shown. THE property of Kerr-Addison Gold Mines is located in the Larder Lake district of Ontario about 3 miles from the Quebec boundary on the highway between Kirkland Lake and Noranda. It is roughly 320 miles due north of Toronto and 365 miles north of Buffalo, N. Y. The property was staked in 1906 and after several development efforts finally came into continuous production at 500 tons per day in 1937. In 1939 the daily tonnage -was increased to 1200 and in 1941 to 2100 tons. At the end of the war, because of the shortage of labor, tonnage was down to 1100 tons per day, rising to 2200 in February 1947. A further plant expansion inaugurated in 1946 was completed by December 1948, bringing the capacity of the mine and mill to a production rate of 4000 tons per day. Current production, with 880 men employed, is 4400 tons per day. Changes in mining methods and equipment, required by the recently completed expansion program, have yielded interesting comparative results, some of which are described in this paper. Hoisting of ore and waste from the mine, as well as all service facilities for handling men and supplies underground, are provided for in a single vertical five-compartment shaft. Ore and waste are hoisted in 12½-ton skips in balance by a 14-ft diam hoist with drums 115 in. wide, grooved for 2?-in. wire ropes. This hoist, with a total rope pull of 85,000 lb, was designed to operate at a speed of 2600 ft per min to a depth of 4000 ft, hoisting 15 tons of ore in each skip. It is amplidyne-controlled and powered with dual drive dc motors of 2250-hp each, through flexible couplings to two pinion shafts, one on each side of the main gear. Each motor has a peak load rating of 4500-hp at point of greatest duty. Direct current power to the hoist motors is supplied from a motor generator set consisting of a 5000-hp synchronous motor driving two 1750-kw dc generators. The loading pockets used so far are at depths of 1500 and 2725 ft respectively. Consequently the present hoisting speed is 2000 ft per min and the skips capacity only 12½ tons. Now that the shaft has been deepened the new pockets at 3934 ft will be increasingly used so that the speed and the skip size will be increased up to original specifications as required. Some difficulty in meeting the required hoisting cycle is expected because of the shape of the skips. As now in use the cross-sectional dimensions of the inside of the skip are 4 ft 6 in. x 3 ft 8 in. To hold 121/2 tons, therefore, they are 14 ft 10 in. deep. Since the skips are the conventional overturning or Kim-berley type, considerable hoisting time is lost in retardation in entering the headframe dump and in acceleration when leaving. It is expected that to obtain the specified tonnage from this hoist when the skip size is increased to 15 tons it may be necessary to resort to bottom dump skips. This type of skip could reduce considerably the present excessive acceleration and retardation times. Analyses of the skip-hoisting operation are made monthly, and every effort is made to reduce controllable delays. For a nine-month period in 1951 such an analysis shows that the hoist was in operation 92.5 pct of the available time, which was allotted as shown in Table I. Overall hoisting costs, cage and skip, for the year 1951, averaged $0.168 per ton of ore milled. The mine is serviced entirely by means of a single cage, capacity 35 men or 15,700 lb, operating in con-

Jan 1, 1954

By George C. Lipsey

FOR many years the mining of coal and other minerals occurring in sedimentary formation has been planned according to information obtained by diamond drilling. Placer mines have used churn drills for sampling and estimating deposits, and some metal mines have used the method either wholly or in part. The diamond drill method, therefore, although not entirely new, has come into more prominence in the last few years. Several large-scale developments now being planned or in the production stage have used this method in varying degree. This paper will describe the operations of the Howe Sound Exploration Co., Ltd. at Snow Lake, Manitoba, where a gold mine was developed and equipped for mining and milling wholly on the basis of diamond drilling results. The property has been in operation nearly 3 years, so that results can be compared with the estimates and assumptions made from the diamond drilling. In developing the subject it is necessary to outline as briefly as possible the normal method of mining, from discovery to production stage. Table I sets forth these various stages, the methods of financing, the percentage of total cost, and the relative time interval required for each section of the work. The plan presented in this table cannot be applied to all mining developments, but it gives a basis on which to work. In Stages 2 and 3 the investment is moderate, and if the property does not respond favorably the options or interests can be terminated. Stage 4 represents a sizeable investment, and it is more difficult to drop the property after this part of the operation is completed. Stages 2, 3, and 4 may be repeated several times by diflerent groups or companies before Stage 5 is reached, but when Stage 5 has been started the total capital investment must be provided and there can be no turning back. It will be noted that there is a total of 116 units of investment in the overall cost if one company proceeds with Stages 2, 3, 4, and 5 in order. Stage 4, however, consumes time which is important when markets are being considered. Bringing a property into production when metal prices are low is much more difficult than when the prices are high, and if this stage can be set aside production is attained more quickly. When Stage 4 is eliminated the total becomes 86 units of cost for Stages 2, 3, and 5, but an adjustment of 14 units must be added to Stage 5. These 14 units represent the useable value of Stage 4. Thus Stage 4 represents an investment of 30 units if carried on before Stage 5, but 14 units if included with Stage 5. This is accounted for by the fact that development work can be accomplished more cheaply under Stage 5, since everything that is done is planned on a production basis with permanent services. Stage 4 must of necessity be governed by expenditures, and a great many temporary services, including housing and power plants, must be provided. The prospect shaft is a small one, and drifts,

Jan 1, 1953

By George C. Lipsey

FOR many years the mining of coal and other minerals occurring in sedimentary formation has been planned according to information obtained by diamond drilling. Placer mines have used churn drills for sampling and estimating deposits, and some metal mines have used the method either wholly or in part. The diamond drill method, therefore, although not entirely new, has come into more prominence in the last few years. Several large-scale developments now being planned or in the production stage have used this method in varying degree. This paper will describe the operations of the Howe Sound Exploration Co., Ltd. at Snow Lake, Manitoba, where a gold mine was developed and equipped for mining and milling wholly on the basis of diamond drilling results. The property has been in operation nearly 3 years, so that results can be compared with the estimates and assumptions made from the diamond drilling. In developing the subject it is necessary to outline as briefly as possible the normal method of mining, from discovery to production stage. Table I sets forth these various stages, the methods of financing, the percentage of total cost, and the relative time interval required for each section of the work. The plan presented in this table cannot be applied to all mining developments, but it gives a basis on which to work. In Stages 2 and 3 the investment is moderate, and if the property does not respond favorably the options or interests can be terminated. Stage 4 represents a sizeable investment, and it is more difficult to drop the property after this part of the operation is completed. Stages 2, 3, and 4 may be repeated several times by diflerent groups or companies before Stage 5 is reached, but when Stage 5 has been started the total capital investment must be provided and there can be no turning back. It will be noted that there is a total of 116 units of investment in the overall cost if one company proceeds with Stages 2, 3, 4, and 5 in order. Stage 4, however, consumes time which is important when markets are being considered. Bringing a property into production when metal prices are low is much more difficult than when the prices are high, and if this stage can be set aside production is attained more quickly. When Stage 4 is eliminated the total becomes 86 units of cost for Stages 2, 3, and 5, but an adjustment of 14 units must be added to Stage 5. These 14 units represent the useable value of Stage 4. Thus Stage 4 represents an investment of 30 units if carried on before Stage 5, but 14 units if included with Stage 5. This is accounted for by the fact that development work can be accomplished more cheaply under Stage 5, since everything that is done is planned on a production basis with permanent services. Stage 4 must of necessity be governed by expenditures, and a great many temporary services, including housing and power plants, must be provided. The prospect shaft is a small one, and drifts,

Jan 1, 1953

By Robert Y. Grant

This study outlines the history of metal mining in Japan and the characteristics of the industry as they existed from 1925 to 1945. Mining and milling operations are described together with the role of the Japanese Government. A description of post-hostilities conditions and the present state of the industry is included. MANY of Japan's larger and better known mines date back to the early centuries of the Christian Era. The first stimulus to mining in Japan came through the growth of Buddhism, A. D. 600 to 700, and the attendant need for copper and other metals for temple ornaments and statues. During the Feudal period, 1333 to 1568, mine operations were expanded to meet the demand for ornament metal and for financing of campaigns. After removal of the seat of government from Kyoto to Tokyo, about 1600, the Tokugawa Shogunate placed great emphasis on mining, and many new mines were opened, some of which are still operating. Toward the end of the Tokugawa period, mining had declined sharply from its earlier peak. The easily worked, high grade portions of the orebodies had been exhausted, and the mining techniques then available could not exploit the deeper, lower grade ores. Similarly, extraction of metal from the sulphide ores presented a major problem. With the Meiji Restoration in 1868 and the rapid opening of the country to western ideas came a rejuvenation of the mining industry. Mining, milling, and smelting processes were greatly improved, resulting in the extension of development work into hitherto inaccessible portions of orebodies. The demand for metal during World War I stimulated activity throughout the industry; copper mining, particularly, expanded to a point where Japan ranked second among world producers.* During the depression following the war, mining underwent a severe contraction in activity, recovering slowly during the late 1920's only to undergo a further setback in the worldwide depression which started in 1929. Mineral output declined in 1930, but the beginning of Japanese expansion, 1931 to 1932, brought about an increase in the output of mine products starting between 1932 to 1934. Production continued to rise, the peak output being attained 1939 to 1943 in virtually all commodities. The greatest production of iron ore, chromite, and manganese was not experienced until 1944 when blocked imports, coupled with strong demands for steel, provided the needed incentive. Through necessity, Japan produced much of her mineral needs from her own mines at high cost during World War 11. Taking the 1932 to 1936 period as an average, however, Japanese mines produced only 16 pct of the iron available to industry, 8 pct of the lead, 33 pct of the zinc, and 68 pct of the copper. Nearly all of Japan's output of gold, silver, copper, lead, and zinc between 1925 and 1945 came from 30 to 49 pct of the mines for which production data are available; for example, 66 of 174 gold-silver mines accounted for 98 pct of the output of this group. Further analysis of mine output indicates that a large part of Japan's metal output was derived from a few large mines; about 10 gold-silver, 15 copper, 3 lead-zinc, 5 manganese, and 2 iron mines account for most of the production. Many of these mines have been operated for 200 to 400 years. With the

Jan 1, 1952

By L. E. Snow, L. F. Pett

AT the Utah Copper Pit of Kennecott Copper Corp. a versatile mobile drill unit has been developed and tested. Through increased drilling speed and additional available drilling time, an improvement of 233 pct in drill performance has been realized. Operators using drill power can quickly and easily convert the unit from a vertical to a toe hole drill. Drilling is done with the machine in line with the unit or at right angles to it. Table I covers the 1950 drill record at the mine, showing the types of machines used and the footage obtained. Development of the new units was prompted by a desire for solution of the following problems: 1—The ever-expanding operations within the Utah Pit, requiring some 65 miles of transmission pipe lines radiating from a central compressed air plant, have now taxed this compressor plant beyond capacity. While 100 lb per sq in. pressure is maintained at compressors, transmission losses from innumerable small leaks result in low terminal pressure at the drills. Fig. 1 illustrates that while terminal pressure varies according to size of air hose and fittings used, the average drill is operating on air pressures within the 60 to 70-lb range. The compressor plant is operated primarily for air rock drills. All drilling is done on day shift, but it is necessary to run two of the three 3720 cu ft capacity compressors during night shift in order to prevent drastic loss of pressure through leaks. On day shift all three compressor units are operated at capacity, so that there is no reserve safeguard available for extensive repairs to any compressor. The calculated volume of compressed air required for operation of 25 drills is but 33 pct of three day-shift compressors. While compressed air is being used to a minor extent for purposes other than drilling, it is felt that satisfactory substitute facilities could be pro- vided in the event that air lines were no longer available. 2—Drill performance has increased beyond the capacity of present 3-in. drifter machines. 3—The installation, maintenance, and moving of air lines in routine mining is a growing problem. The 2-in. level lines are placed outside electrification towers and must be moved to new location upon completion of each shovel cut. In addition to these moves it is often necessary to dismantle level lines so that excessive shovel spillage, or material covering track following a blast, can be pushed in the clear with bulldozers. Where level room is limited, it is often necessary to remove air lines in giving bulldozers room to prepare grades for wagon drills. In spite of precautions taken, many level lines become buried, twisted, and constricted, with excessive air loss resulting. Excessive back break in blasting often leaves several sections of air line suspended in mid-air. Occasionally air lines come in contact with defective electric transmission towers, so that holes are burned through pipe. 4—Rail-handling of drilling equipment such as wagon drills from one location to another requires considerable locomotive crane crew time. Any new unit developed should travel under its own power. 5—Present practice requires accessory material including hose, water pressure tanks, water barrels, drill steel, and bits to be transported by means of push cars when drill locations are changed on any level. 6—In order to supply numerous drill locations with material, many stock piles of new drill rods, drill bits, and other essentials must be left at strategic points, usually in the vicinity of powder magazines. This practice makes for poor housekeeping and contributes to the loss of supplies. Planning the Unit It was felt that a mobile drill unit which would rectify the foregoing problems should meet certain demands: 1—It must furnish compressed air to operate a 4-in. rock drill at a pressure of 90 to 100 lb.

Jan 1, 1953

By L. E. Snow, L. F. Pett

AT the Utah Copper Pit of Kennecott Copper Corp. a versatile mobile drill unit has been developed and tested. Through increased drilling speed and additional available drilling time, an improvement of 233 pct in drill performance has been realized. Operators using drill power can quickly and easily convert the unit from a vertical to a toe hole drill. Drilling is done with the machine in line with the unit or at right angles to it. Table I covers the 1950 drill record at the mine, showing the types of machines used and the footage obtained. Development of the new units was prompted by a desire for solution of the following problems: 1—The ever-expanding operations within the Utah Pit, requiring some 65 miles of transmission pipe lines radiating from a central compressed air plant, have now taxed this compressor plant beyond capacity. While 100 lb per sq in. pressure is maintained at compressors, transmission losses from innumerable small leaks result in low terminal pressure at the drills. Fig. 1 illustrates that while terminal pressure varies according to size of air hose and fittings used, the average drill is operating on air pressures within the 60 to 70-lb range. The compressor plant is operated primarily for air rock drills. All drilling is done on day shift, but it is necessary to run two of the three 3720 cu ft capacity compressors during night shift in order to prevent drastic loss of pressure through leaks. On day shift all three compressor units are operated at capacity, so that there is no reserve safeguard available for extensive repairs to any compressor. The calculated volume of compressed air required for operation of 25 drills is but 33 pct of three day-shift compressors. While compressed air is being used to a minor extent for purposes other than drilling, it is felt that satisfactory substitute facilities could be pro- vided in the event that air lines were no longer available. 2—Drill performance has increased beyond the capacity of present 3-in. drifter machines. 3—The installation, maintenance, and moving of air lines in routine mining is a growing problem. The 2-in. level lines are placed outside electrification towers and must be moved to new location upon completion of each shovel cut. In addition to these moves it is often necessary to dismantle level lines so that excessive shovel spillage, or material covering track following a blast, can be pushed in the clear with bulldozers. Where level room is limited, it is often necessary to remove air lines in giving bulldozers room to prepare grades for wagon drills. In spite of precautions taken, many level lines become buried, twisted, and constricted, with excessive air loss resulting. Excessive back break in blasting often leaves several sections of air line suspended in mid-air. Occasionally air lines come in contact with defective electric transmission towers, so that holes are burned through pipe. 4—Rail-handling of drilling equipment such as wagon drills from one location to another requires considerable locomotive crane crew time. Any new unit developed should travel under its own power. 5—Present practice requires accessory material including hose, water pressure tanks, water barrels, drill steel, and bits to be transported by means of push cars when drill locations are changed on any level. 6—In order to supply numerous drill locations with material, many stock piles of new drill rods, drill bits, and other essentials must be left at strategic points, usually in the vicinity of powder magazines. This practice makes for poor housekeeping and contributes to the loss of supplies. Planning the Unit It was felt that a mobile drill unit which would rectify the foregoing problems should meet certain demands: 1—It must furnish compressed air to operate a 4-in. rock drill at a pressure of 90 to 100 lb.

Jan 1, 1953

By E. R. Borcherdt

IT is notable that the first large-scale mine operation equipped entirely with detachable bits was the Badger State mine of the Anaconda Copper Mining Co. in Butte, Montana, just 30 years ago. This mine in 1922 was producing approximately 1200 tons of ore per day. Much of the data presented in C. L. Berrien's article' describing the development and installation of the Hawkesworth detachable drill bit were obtained from these operations. As in any pioneering effort, no precedent existed and many difficult problems required solution, so that the changeover to detachable bits at all Butte hill mines was not completed for 6 years. There was widespread disbelief as to the probable efficiency of the new installation. Some attempts were made in 1931 by the owners of the Hawkesworth patents to interest Ontario gold mine operators in the bit. These efforts were not successful, but they undoubtedly stimulated thinking which resulted in the invention and patenting of several well-known Canadian detachable bits, one of which is now a widely used throwaway bit. The success of the Butte installation also led to the development of the threaded type of bit connections by several well-known manufacturers, and in 1935 these bits were introduced to the mining industry on a national scale. The original Hawkesworth bit was not provided with a water hole but, depended upon water passing through the clearance opening between the tongue in the bit and the groove in the rod to flush cuttings from the drill hole, see Fig. 1. In December 1935 it was found that this method of introducing drilling water to the bit face resulted in high dust counts. To correct this a water hole was drilled on the central axis of the bit, passing through the tongue. Unfortunately, quenching water would rise through the small water hole, spot-hardening the tongue to cause breakage, never completely eliminated. In the fall of 1936 large-scale tests indicated that savings would be effected by use of a threaded type of bit, which was therefore adopted as standard for all Butte mines. This type of bit was used until 1947, when it was superseded by a one-use slip-on type. Since the first use of the Hawkesworth bit every detachable bit of importance has been investigated, and where advantages which might reduce costs or increase efficiency were indicated, substantial tests of the bit were carried on in the Butte mines. When tests demonstrated the advisability of changing from one kind of detachable bit to another the change was made at one level or in one area each day until the new rod and bit equipment was used throughout the mine. This involved a minimum of cost and disruption of drilling. Intelligent selection of a detachable bit to obtain optimum results requires careful consideration to achieve a balance between the three principal types of equipment used in the drilling process: 1—drill bits, 2—drill steel, and 3—drilling machines. Optimum results imply maximum output and minimum cost per unit of output. Since every rock type differs in drillability and it is generally impractical to provide equipment for more than one or two types of rock which may occur in one operation, selection of equipment must encompass average drilling conditions. However, on exceptional occasions several widely differing conditions may make it mandatory to provide equipment best suited to each condition. The choice of rock-drilling equipment is a most controversial subject and one that is further complicated by unreliable and frequently misleading performance claims. Small operators without the means for making accurate evaluations of equipment frequently suffer from these over-enthusiastic claims. It is apparent from experience in rock drilling throughout the world that rock drillability is not alike in any two places, and that selection of proper equipment can only be made after conducting thorough trials of various types of equipment. Some recent drilling tests in tactite and hornstone at the Darwin, California mine of the Anaconda Co. present some interesting clues on rock drillability. Microscopic examination of thin sections of these rocks reveals that mineral composition and rock texture are equally important in governing drillability. The Darwin hornstone is at times so abrasive that the carbide bit cutting edges become flattened to 3/32 in. in 2 to 4 ft of drilling, and some carbide bits were dulled to this point after 9 to 10 in. of drilling. This wear was determined to be the proper point for resharpening to eliminate carbide insert breakage or breakage of the steel rod when drilling with 1½ to 1?-in. bits, with a drifter of 2 3/4-in. diam and 90 to 100 psi air pressure, see Supplement A. Before considering the merits of various bit designs it may be well to review the mechanics of drilling rock with percussion drills. A sharp bit cuts by penetration and chipping. The amount of penetration governs the amount of chipping and depends upon the contact area of the cutting edge, the foot-

Jan 1, 1954

By Gerald C. Mathis

FERGUS County, Mont., shown in Fig. 1, is known for its once famous gold mines near the old towns of Gilt Edge, Maiden, and Kendall. But at Heath, a small farming community near the foothills of the Snowy Mountains, thousands of tons of gypsum have been mined since 1916. The value of the gold taken from the mines of Fergus County runs into millions of dollars; the value of the products made from the gypsum of the Heath mine is also in the millions. The gypsum mine will continue to produce for many years, while the gold mines are closed today. The Heath gypsum mine was developed by the Northwest Gypsum Co. in 1916. The products of the small mill built by this company were plaster, agricultural gypsum, and raw gypsum for cement manufacturing. The United States Gypsum Co. prospected the adjacent property in 1916 and 1917 by means of two adits and some exploration drill holes. During World War I, the company abandoned operations at Heath, but again became active in this area in 1928 hen it purchased all the property of the Northwest Gypsum Co. A long range program of expansion was begun with the building of a block plant and the purchase of additional land and mineral rights. A modern wall board plant was built in 1936. When the old wooden mill purchased from the Northwest Gypsum Co. burned in 1937, an all-metal calcining plant located at Blue Rapids, Kansas, was dismantled, moved to Heath, and erected on the site of the mill. In August 1951 a new mine was opened 3000 ft north of the mill. Rock is conveyed from the mine to the mill by an 18-in. belt conveyor. The Heath gypsum deposit lies at the base of the Ellis formation of Jurassic Age. The Ellis at Heath lies unconformably on the black fissle shale of the Heath formation of the Big Snowy Group, which is Mississippian in age. The strike of the gypsum bed is N45°E and the dip approximately 3" NW; the regional strike and dip of the area. The gypsum lies in a series of six layers separated from each other by thin seams of shale. The lower layer is composed of' gypsum and shale intermingled and is not of commercial grade. The upper five layers are high in purity, but only the middle four layers are mined on the advance, as the top layer is left for roof support. This top layer is mined on retreating operations at the same time the pillars are robbed. Total thickness of the gypsum layers varies from 12 to 14 ft. Fig. 2 shows the average thickness and arrangement of the layers. Mining Methods The mine was originally developed by driving an adit into the gypsum horizon. The Northwest Gypsum Co. mined in the top four layers, the top layer being split, leaving about 12 in. for roof support. A modified room and pillar method was used: entries were 15 ft wide and rooms varied between 20 and 30 ft and were turned on 90" from the entries. Crosscuts between the rooms left pillars from 10 to 20 ft square. The rock was loaded by hand into 1-ton mine cars and pulled to a central gathering point by mules; from the gathering point, mules or horses were used to pull the string of cars to the mill tipple. This method was continued by the United States Gypsum Co. from 1928 to 1937.

Jan 1, 1954

By Carville E. Sparks, Rollin Farmin

TRIAL installations of rock bolts, of the slit-rod-and-wedge type, were under way at several units of Day Mines, Inc., when Korean hostilities interrupted the already slow deliveries of steel bars to the Coeur d'Alene district. Factory-made bolts had not yet been put on the local market, so the program was halted for lack of supplies. Interest was revived by a visitor's description of wooden roof bolts. These were said to have been used briefly with apparent success in a coal mine, until apprehension voiced by the U. S. Bureau of Mines caused the practice to be suspended. To make wooden bolts for trial in ground support, Day Mines acquired a second-hand doweling machine equipped with two cutting heads, one to turn out the desired round rods of 2-in. diam, the other to turn out 1-in. rods to be used as powder-tamping sticks. This machine was installed in the all-weather sawmill of the Hercules mine unit at Burke, Idaho, where fabrication of the wooden bolts commenced early in 1951. Most of the mining in the Coeur d'Alene district is along steeply dipping veins in shaly quartzite and argillite of Algonkian age. Ground support commonly is required in zones where the rocks have been sheared, brecciated, and hydrothermally altered. Pressure from the sidewalls is more troublesome than weight overhead, but both increase with the size of the mine opening. Caving may come from a progressive sloughing of irregular rock fragments or from an exfoliation and buckling of the layered wall rocks. The disintegration is thought to develop from an initial elastic expansion of the rock toward the newly-created mine opening, followed by the dilation of many tiny partings in the rock by absorption of water. As the partings widen, masses of rock develop weight and become free to fall. The function of rock bolts is to prevent or retard widening of partings in the rock supported. Wooden Bolts, Wedges and Headboards Bolt assembly used by Day Mines consists of a bolt 4 or 6 ft long, two wedges 16 in. long, and a headboard 30 in. long, Fig. 1. All four pieces are made of local red (Douglas) fir, either green or well-soaked in the mill pond before it enters the sawmill. Bolts are fabricated from cants, 2 1/4 in. sq, cut from relatively straight-grained timber with a minimum of knots and trimmed to 4- and 6-ft lengths. The bolt then is turned in the doweling machine from 21/4 in. sq to 2 in. diam round, except for a 4-in. length at one end which is left full square to provide the striking head and the shoulder that holds the headboard in position for wedging. The foot end of the bolt is slit with a thin saw for a length of about 16 in., thereby making a slot to receive the wedge against which the bolt is driven for anchorage at the bottom of the rock hole. A similar slit, 12 in. long, is made in the opposite (head) end of the bolt to receive the second wedge, which crowds the headboard against the ground at the collar of the rock hole and puts the bolt in tension. The second slot is aligned 90" from the plane of the first slot to avoid Longitudinal splitting and is notched out slightly to allow easier insertion of the collar wedge after the bolt has been driven to bottom. To prevent splitting the headboard by spreading action of the head wedge, this slot is oriented at 90" to the grain of the headboard when the pieces are assembled, Fig. 2. The wedges are similar to standard mine wedges, but more slender; they are cut 1 7/8 in. wide and 1 in. thick at the heel and taper out in 16 in. of length. The headboard, or bearing plate, is not necessary for some types of ground but generally is desirable because it helps the bolt to support an area of loose, friable rock and reduces the tendency for the rock at the collar of the hole to split away from the wedged head by distributing the pressure over a wider rock surface. The headboard may be a 24-to 30-in. length of 3-in. plank, 8 to 12 in. wide, but a similar length of rounded sawmill slab serves equally well at 20 pct of the cost. A hole of 2-in. diam is bored or punched through the center of the headboard, either at 90" or at various high angles to its surface. The bolt is inserted to its shoulder through this hole, then driven into the rock hole. Bolts, wedges, and headboards are given a full timber preservative treatment to inhibit rot. Bundles of each are immersed in a warm saturated solution of Osmose salts in water for 48 hr, removed, dripped dry, and stored in a relatively humid underground depot to cure. Most wooden rock bolts used by Day Mines are 4 ft long. Holes to receive them, about 42 in deep and 2 1/8 in. in diam, are drilled into the rock' to be supported, nearly normal to the periphery of the mine opening. The type of drill used is dictated by convenience: stoper, jackleg, or jumbo-mounted drifter. Correct depth of the hole is assured by use of a measuring stick that has been cut to the proper distance from drill chuck to the ground at the collar of the hole when a standard length drill rod is at the bottom. The bolt is seated to the shoulder through the hole in the headboard, the foot-end wedge is placed in its slot, and the assembly is inserted into the rock hole. Then the bolt is driven until it is seated solidly on the wedge against the bottom of the rock hole. Driving may be by hand with a sledge, or

Jan 1, 1954

By A. E. Lillstrom

IN the development of iron mines and production of iron ore from the Marquette range, drilling blast-holes is an important phase of the mining cycle. The ground drilled in ore production can be classified into two main categories, soft hematite and hard hematite or magnetite. Within these categories the material exhibits a wide range of penetrability by percussion drills. Development work encounters various types of rock. Slate and altered basic intrusives constitute the softer types commonly encountered. Harder materials are represented mainly by greywacke, quartzite, iron formation, and diorite. Prior to the first tungsten carbide trials in late 1947 and early 1948, hard-rock and ore drilling was done with steel jackbits starting at 21/4-in. diam. These were reconditioned by hot milling. Automatic or handcrank 31/2-in. drifters were employed, mounted on Jumbos, posts and arms, or tripods, depending upon the working place. With the exception of shaft sinking jobs where 55-lb sinker machines were and still are used with 1-in. quarter octagon steel, the other production and development mining utilized 11/4-in. round and Leyner-lugged steel. The following properties have been selected as typical examples wherein carbide bit applications have proved economical. The Mather mine "A" and "B" shafts and Cleveland-Cliffs Iron Co. mines are soft ore mines where insert bits are used in rock development only. The Greenwood mine, Inland Steel Co., Champion mine, North Range Mining Co., and Cliffs shaft mine, Cleveland-Cliffs Iron Co., are hard ore mines where all drilling is done with tungsten carbide bits. Mother Mine "A" Shaft In the Mather mine "A" shaft and other soft ore properties where only rock development work is done with the tungsten carbide bits, several types and makes of bits have been tried since early 1948. The greatest proportion of failures have been at the connection end, although the early trials with the 13 Series Carset 11/2-in. bit used in conjunction with 31/2 -in. automatic-feed drifters, showed an equal amount of shattered inserts. To combat this shattering, the 31/2 -in. drifters were replaced by 3-in. drifters, thus eliminating, for the most part, insert failures. However, the attachment end of the rod continued to be the main source of trouble. The greatest amount of failure was in the stud or at the upset section approximately 2 in. behind the drive shoulder of the rod. Heat treatment was changed several times as well as the composition of the alloy studs. Since this failed to correct the trouble, a decision was made to change to a heavier attachment section. Timken 11/2-in., type M, bits were then employed and showed an exceptional improvement. The rods are discarded when the thread contour shows sharpening or wear on the shoulder. It was also learned that the Timken insert did not show as rapid gage and cutting edge wear as did competitive makes, and footage per use increased by approximately 50 pct. Prior to the Timken trials the average life per bit at the Mather mine "A" shaft on 6-ft change chain-feed drifters was 500 ft, and the rod life at the connection end was 50 ft. The Timken bit with chrome-plated thread averaged 1200 ft, and rod life increased to as much as 500 ft. However, the life of the connection end was much better on shorter length drill rods or in places where machines with 34-in. change were used. The bit thread continued to be the point of ultimate failure with thread strippage, constituting the cause for discard of bits. In one of the new development headings, harder rock was encountered for approximately 800 ft, dropping the life per bit to a low of 90 ft with shank and thread life of rods dropping to approximately 125 ft average. The stripped bits were then welded to the rods, increasing the life per bit by 75 to 100 pct. The rod transportation for main level development was not a problem so intraset rods were tried. Intraset rods have tungsten carbide inserts set into the rods proper by the manufacturer and can be obtained with chisel or four point bits. This type of rod eliminates the need for any connection and the steel being a special alloy will show more feet drilled per rod. The first trial was made with eight rods, and final results averaged 350 ft per rod, six of the rods worked the life of the bit end, and two broke shanks at less than 50 ft. The preceding example showed a considerable improvement, so additional steel of the same type was purchased, but its use has been limited to main level drifting only, because of the handling problem involved in transportation of the complete rod to mine shops for resharpening. Further trials are being made on improving the life per detachable bit by chrome plating. To date, the chrome plating shows an improvement of approximately 100 pct. However, final results will not be known until the present long term trials have been completed. Mother Mine "B" Shaft In November 1947, tungsten carbide bits were first tried at the Mather mine "B" shaft. The use of 1%-in. Carset 13 Series bits, for drilling the 72-hole, 7-ft shaft round, decreased the drilling time from an average of 41/2 hr per round required with steel bits, to 2 hr with insert bits. The best drilling time for

Jan 1, 1952

By W. F. Netzeband

Jan 1, 1927

By W. J. Taylor, H. J. Mutz, A. F. Brock

THE International Kickel Co. of Canada Ltd. operates five underground mines and an open pit. Four of the mines, the Frood-Stobie, Creighton, Murray, and Garson, are on the south range of the Sudbury Basin, map above, within a radius of 10 miles of the city of Sudbury, Ontario. The fifth mine, the Levack, is on the north range of the Sudbury Basin, 30 miles to the northwest of the city. The open pit is operating on surface ores of the Frood-Stobie orebody. Two pits were opened at the Frood-Stobie mine; the Frood section was started in 1938 and the Stobie section in 1942. To meet the heavy demand for nickel during World War 11, open-pit production was accelerated until it constituted over 40 pct of Inco's total tonnage. As a consequence open-pit ore was depleted considerably alhead of schedule; the Stobie pit was completed in the summer of 1951, and it is expected that mining at the Frood pit will be completed in 1953. The major program launched 10 years ago to develop additional underground production as a replacement of open-pit tonnage thus had to be greatly speeded up. This conversion to all-underground mining will be completed within the next two years, and the underground mines will then have an annual hoisting capacity of 13,000,000 tons. One of the new mines in the underground expansion program, the Murray, was brought into production in 1950. Ore production from the new Stobie section of the Frood-Stobie mine was commenced on a limited scale in 1951 and will be increased as the program progresses. Delivery of ore to the new Creighton mill was started in the summer of 1951 from the caving project launched at Creighton mine. When mining was started in the Sudbury district 65 years ago the ore deposits were opened on a small scale and mining methods conformed to a general pattern of small open cast pits, followed by open stopes as mining was extended below the pits. The open stoping methods used were heading-and-bench and shrinkage. In certain cases a type of cut-and-fill mining was used with drywall tramways and dry-wall chutes in the fill. As the mines were deepened,

Jan 1, 1954

By E. W. Felegy

THE need for improved mine communication to increase efficiency and to insure greater safety has long been recognized. General and unrestricted communication between all points underground, and between the surface and all points underground, is probably the least advanced phase of the mining industry. An ideal system of mine communication must require no fixed wire installations. The equipment must be small, lightweight, and readily portable, and the power requirements low. A system that can be used not only under normal circumstances but also in an emergency, when the continuity of wires, tracks, and pipelines may be disrupted, must function independently of any aid furnished by standard installations. Radio communication offers possibilities of meeting all the requirements necessary for an ideal communication system in underground mines. Transmission of signals must be achieved through one or both of two mediums, through the air in mine openings or through the strata. The results or lack of results obtained by early investigators showed conclusively that radio communication by space transmission cannot be accomplished effectively beyond line-of-sight distances in underground passageways. A radio system underground therefore must depend solely upon transmission through soil and strata. The application of radio to underground mine communication was investigated by many individuals and agencies at different times in the last several decades, but little success was achieved before World war 11.2-0, The results of experiments during the war, and further knowledge gained in experiments with vastly improved communication methods and equipment after the war provided the background for additional research in radio communication in underground mines. During 1950 to 1.952 the University of Minnesota sponsored an investigation to determine the possibility of developing: a system of radio communication universally applicable in underground metal mines in the Lake Superior district. The possibility of using radio equipment to determine the imminence of rock bursts in deep copper mines in that district also was investigated. The investigation supplemented previous and concurrent emergency mine communication studies of the U. S. Bureau of Mines. Testing equipment and laboratory facilities maintained by the Bureau of Mines at Duluth, Minnesota, were used in the research program, which was conducted as a mining engineering graduate research problem by the present writer under the direction of T. L. Joseph and E. P. Pfleider. The radio units used in the research program were designed and built to specification solely to conduct tests of radio communication in mines. Two identical units were used in all tests. Each unit contained a transmitter section, a receiver section, and a power-supply section, mounted on a single chassis. The entire unit was enclosed in a single 10x12x18-in. metal case provided with a leather-strap handle for carrying purposes. The front of the case was hinged to open upward and provide easy access to the single control panel on which all controls were mounted. Storage batteries supplied the operating power for all tests. Standard 6-v automobile batteries were utilized to provide adequate capacity to conduct tests for a full day without exhausting the battery. A frequency range from 30 to 200 kc was covered in eight pre-fixed steps on each unit. The carrier frequencies were crystal-controlled and amplitude-modulated. The receiver employed an essentially standard superheterodyne circuit and was sufficiently sensitive to detect signal strengths of 5 micro v. A heterodyne circuit was employed in the transmitter to obtain the low-carrier frequencies used in the units. Power output of the transmitter, usually less than 2 w, rarely exceeded 3 w in any test. Tests were conducted in mines on the Vermillion iron range in Minnesota, the Gogebic iron range in Wisconsin, the Menominee and Marquette iron ranges in Michigan, and a copper mine in the upper Michigan peninsula. All tests were conducted when the mines were operating normally, and usual mining, maintenance, and transportation activities were in progress, so that any interference caused by normal production activities could be evaluated during the tests. Tests were made between different points underground in each mine, and between underground and surface points at some mines. Test readings obtained at any one mine were calibrated in the laboratory before another series of tests were begun at the next mine. The transmitter and receiver were separated by one or more levels in each test, and generally there was no other means of communication between test points. Two 100-ft lengths of rubber-covered wire were used for antenna wires on each unit in both transmission and reception. The ends of the wires were connected to ground points in one of several methods, depending upon physical conditions at each test site. The wires were clipped to metal rods about 200 ft apart in the back, side, or bottom of the mine opening where the character of the rock permitted driving rods. Both wires were clipped to points about

Jan 1, 1954

By Joseph Bernhardt

THE Cornwall Ore Mines, Division of the Bethlehem Steel Co., at Cornwall, Lebanon County, consists of two separate magnetite ore bodies, approximately one mile apart. The one ore body was an outcrop in which open-pit mining operations were begun in 1742 and continued without interruption. This mine is also served by a shaft for mining that portion of the ore body not recoverable by open-pit methods. The other property had no outcropping and is entirely an underground operation. This mine, cap-tioned No. 4 mine, is serviced by two shafts 220 ft apart. The No. 4 shaft is for hoisting rock and ore, and the No. 5 shaft is for handling men and ma- terials. The shafts are on a catenary curve, closely following the dip of the ore body. Slope of the shafts at the collar is 36", flattening to 26" at the bottom. The footwall at Cornwall is a traprock which varies structurally from solid to highly fractured. Grizzly stations at the top of each chute raise were reinforced by setting timber sills on concrete. Occasionally it was necessary to concrete the entire chute raise. Concreting was done by using 35-yd electric mixers set up in the breaking subs. Sand, stone, and cement were hoisted up through the chute raises to the breaking subs. Late in 1937 it was decided to eliminate chute raises and breaking subs in future development. Haulage levels are 50 ft apart vertically. When ore is below a 40 " dip, slushing drifts are driven normal to the haulages and on 40-ft centers. In a few areas, ore dips greater than 40" and slushing drifts are then placed parallel to the haulage drifts. Finger raises are opposite each other and on 20-ft centers making 20x20-ft draw areas (fig. 1). For loading

Jan 1, 1951

By Joseph Bernhardt

THE Cornwall Ore Mines, Division of the Bethlehem Steel Co., at Cornwall, Lebanon County, consists of two separate magnetite ore bodies, approximately one mile apart. The one ore body was an outcrop in which open-pit mining operations were begun in 1742 and continued without interruption. This mine is also served by a shaft for mining that portion of the ore body not recoverable by open-pit methods. The other property had no outcropping and is entirely an underground operation. This mine, cap-tioned No. 4 mine, is serviced by two shafts 220 ft apart. The No. 4 shaft is for hoisting rock and ore, and the No. 5 shaft is for handling men and ma- terials. The shafts are on a catenary curve, closely following the dip of the ore body. Slope of the shafts at the collar is 36", flattening to 26" at the bottom. The footwall at Cornwall is a traprock which varies structurally from solid to highly fractured. Grizzly stations at the top of each chute raise were reinforced by setting timber sills on concrete. Occasionally it was necessary to concrete the entire chute raise. Concreting was done by using 35-yd electric mixers set up in the breaking subs. Sand, stone, and cement were hoisted up through the chute raises to the breaking subs. Late in 1937 it was decided to eliminate chute raises and breaking subs in future development. Haulage levels are 50 ft apart vertically. When ore is below a 40 " dip, slushing drifts are driven normal to the haulages and on 40-ft centers. In a few areas, ore dips greater than 40" and slushing drifts are then placed parallel to the haulage drifts. Finger raises are opposite each other and on 20-ft centers making 20x20-ft draw areas (fig. 1). For loading

Jan 1, 1951

By S. H. Ash, J. J. Forbes

Probably the newest thing in mining safety, or safety for mines, is the apparent dissatisfaction on the part of the mineral industries, as represented by both management and labor, and the general public of the Nation, with the safety record of the mining industry. This is reflected by published comments and papers in the technical press;l-9 in labor periodicals,10,11 in popular journals and periodicals,l2, 13 and in the daily press; also by discussions of the Safety Committees sponsored by the National Safety Council,9, 14-15 the American Mining Congress,l.l6 the American Institute of Mining and Metallurgical Engineers,2,4 the Mine Inspectors' Institute of Amerthe Coal Mining Institute of America,5 19 the American Standards Association, and others.20.21 Mining safety is a joint problem of management and the individual workman. Safety is not attained and will not be attained solely by laws, decrees, and commands because, if it could be done in this manner, acceptable mining safety would have been achieved long ago by the individual states in our Nation and by the nations abroad. The best safety performance is found at plants where management provides a safe environment for the workers; where supervision is efficient and super- visors, others concerned with promoting safety, and the individual worker know through training, experience, and personal contact the safe and unsafe practices of their field; and where the trained individual worker has become safety-minded by experience, quiet influence, unconscious suggestion, and personal guidance. Despite what may be said to the contrary, progress has been and is being made in mining safety. This is shown in Fig 1 to 4. It is beyond the scope of this paper to give possible reasons for the valleys and peaks in the fatal-injury rates. Some recent factors that appear to be contributing to the improvement in these rates are briefly discussed. Aside from mining equipment, "what's new in mining safety" for some mines has been in effect or was tried by others long ago. A safety pro- gram is a living thing; as such, it must be vitalized and continuously fed with enthusiasm, constructive action, and improvements. Because safety is concerned with human conduct, it is necessary to practice safety at all times; if not, it is soon forgotten, and accidents occur. Mining-safety Records The large employment and production concerned with anthracite contribute much to the mining-safety records of the mineral industry. Approximately 81,000 persons are. employed in this industry having mines concentrated in an area of 480 square miles in northeastern Pennsylvania. Because of the achievement of the anthracite industry in safety during 1948, the other branches of the mineral industry can profit by a study of what has been done to achieve that record. Where one mineral is produced by other large groups having methods of mining that are similar in many respects to the anthracite-mining methods, an achievement in such a large industry is important. Salient factors concerned with safetye in the anthracite industry are: no radical change has occurred in the mining-safety regulations pertaining to anthracite mines. Because anthracite mining is a branch of the coal-mining industry,

Jan 1, 1950

By William J. Coulter

WITHIN the United States the problem of meeting maximum production by our metal mines has been solved by: (1) Conservation of man power by mechanization. (2) Increasing man-power efficiency as expressed in tons per man-shift by the adoption of new and more efficient methods. (3) Production from submarginal properties made possible by some form of government subsidy. (4) Selective mining of high-grade areas. (5) Drawing on broken ore reserves and reducing advanced development work to a minimum. (6) Making maximum use of available equipment. (7) Repairing equipment that normally would be replaced. (8) Working a seven-day week on a three-shift basis to get maximum use of equipment and man power. (9) Adoption of incentive plans to increase maximum efficiency and unit production. (10) Important advancement in metallurgy, resulting in larger recoveries. (11) Improvements in safety, health, and general working and living condi-

Jan 1, 1945

By Wallace R. Horn

"MR. CHAIRMAN AND GENTLEMEN :I begin this talk by making a couple of comments which are of the nature of disclaimers.Firstly, and as the Chairman has otherwise indicated, I was neither ""born into"" nor have I spent more than a few years of my professional life in the mining industry. I mention this because many might, and perhaps rightly, consider that an added qualification in presenting a report of what the industry has accomplished. Indeed, I am not here to blindly defend all of its actions and inactions in respect to environmental control over the years. Nor am I here to seek absolution of the industry's past transgressions - if indeed that is the word. Mistakes might be a better one. I concluded some time ago that the effects of those mistakes are too difficult to assess against the sea of errors of our total society. I should mention too that I am not an environmental engineer or specialist - only a portion of my interest is involved with this field. Perhaps this permits a perspective which allows a more accurate and objective view.One further comment here. My job today, as I understand it, is to generally report upon the nature and extent of the response of the metals mining industry to control of the environment. In the case of an industry operating at more than a hundred locations and for various reasons at various stages of progress, it is not an easy job. On the other hand, I wanted to avoid the use of generalities because, especially within the context of environmental or ecological opinion and of the practice of condemnation of industrial segments, I think we've had about enough of generalities until we know far more than we do.Finally, I am quite aware that a statement of future plans to achieve environmental control does not impress or satisfy as many people as it may have done some years ago. Public opinion demands to know what is currently underway, today."

Jan 1, 1972

In 2007, a total of 278 metal mining operations reported employment to the Mine Safety and Health Administration (MSHA).1 Metal mines were the smallest mining commodity sector, comprising 1.9% of all mining operations. ? Gold mines comprised 44.6% (n=124) of all metal mining operations. Other common types of metal mines were iron ore (n=36; 12.9%) and copper ore (n=35; 12.6%). ? Nevada had the largest number of metal mines (n=45; 16.2%), followed by Alaska (n=28; 10.1%).

Aug 1, 2009