Search Documents

By David Kress

Grinding mills, both autogenous and ball can be powered by several basic means. The three methods used today are girth gear drives, gearless drives and trunnion coupled reducers. This paper will focus on the first of these methods -girth gear drives. The girth gear drive has been used on thousands of mills which continue to operate successfully. These drives are noted for their simplicity and low cost. In the past, the horsepower capacity of girth gears has been slow to keep up with the horsepower increase required by the mill builders, particularly since the advent of the SAG mill. Gear manufacturers had capacity for 2000 HP mills in the 1950's, 5000 HP in the 1960's and 6500 horsepower in the 1970's. The 70's and 80's brought dual pinion girth gear drives which allowed mill sizes beyond 10,000 horsepower. Gear manufactures who could not keep up with the pace of the horsepower demands and the quality and reliability demanded by the mill builders and users have fallen by the wayside.

Jan 1, 1991

By G. H. McKay

AT the Eagle mine, near Gilman, Colorado, where the Empire Zinc Company have installed an underground mill, transportation problems were comparatively simple. A railway siding on the Denver and Rio Grande railway is equipped with an unloading dock or platform at the portal of their service incline adit to the mill. This 18-degree incline is approximately 600 feet long from the unloading track to the head of the mill skipway. For the Big Missouri mill, upwards of 2,500 tons of material and equipment had to be trucked from tidewater at Stewart, B.C., a distance of 21 miles to the Big Missouri camp at elevation 2,800. From that point, this freight had to be moved either over or through the Big Missouri ridge, rising to elevation 3,450, to its final location 800 feet from the surface between elevations 2,150 and 2,350. Immediately after leaving the government dock at Stewart, the road crosses the International boundary line into Hyder, Alaska, and then follows a water grade for eleven miles along the lower stretches of the Salmon river. leaving the river, the road climbs for two miles before crossing back into British Columbia territory at Silver Heights, and then continues for another mile and a half to where the Big Missouri road branches off from the main road to the Premier mine. For a distance of four miles from the junction of the roads, the Missouri road is very narrow, with many sharp curves and with irregular up and down pitches and grades up to 25 per cent until it reaches the Summit. From there on, a fairly easy grade leads a mile and a half to the end of the road on Joker Plats. In winter, the last stretch of road is subject to heavy snow drifting, especially through a narrow funnel-shaped gulch, known as 'The Gap', where the snow may pile up to a depth of over twenty feet.

Jan 1, 1938

By R. Paturi

Mill liners play an important role in the operation of a mineral concentrator influencing the throughput, availability, power drawn and the efficiency of the mill in the plant. Liners protect the shell and transfer energy to the grinding charge. Metso Technology Development has conceptualized, developed and successfully implemented physics based 3D DEM simulation techniques to predict charge motion, power drawn, energy spectra and wear over the life of the liner. This paper will present a case study of shell liner optimization for a 34? SAG mill including the input data requirements, and shell liner optimization methodology using the 3D simulations that eliminates the need for the traditional expensive and lengthy proto-type testing. These simulations will cover ball and particle movement, liner wear and mill power draw, and do not cover particle breakage and slurry flow. Even the liner manufacturers lack the ability to provide this type of qualitative and quantitative information on their products. The data from these simulations provides the plant engineers a scientific basis for their decision making and thus eliminates guess work. Keywords: liner, optimization, multi-physics, 3D-DEM

Sep 1, 2012

By Homero Delboni Junior, Thiago Nunan, Flávia Vargas

Ball mill liners perform two main functions in grinding process: protect the mill shell from the aggressive milling environment and delivery input power to the charge. When it comes to liners optimization the challenge are to prolong the service life and improve grinding performance. Some liners characteristics such as A / B ratio, lifters number, lifter height, and attack angle are extremely relevant to grinding process. By analyzing process data, and through DEM simulations application, these parameters were improved on W-mill liner, located at Vazante concentration plant. The new profile promoted a reduction of power variability between the final and the initial life cicle intervals and, therefore, better stability to circuit operation. In addition, the new liner service life reached 21,603 hours, 25% higher compared to the previous one in use. This optimized profile therefore proved to be able to improve its functions by achieving superior process performance combined with longer service life.

Oct 3, 2019

By E A. Gunn, J Zhou

In this paper a project to develop a joint optimisation/simulation model for production planning in a mine-mill complex is presented. The system involves a mill receiving ore from a number of different locations, each with a unique mineral composition. The mill consists of several crushing and grinding circuits that function in series and parallel. Scheduling the flow of materials through the mill is complex due to constraints on throughput imposed by the millÆs design, the length of time material can be stockpiled on the surface, varying input mineral composition, and throughput targets for a range of output products.An optimisation model is used to create a set of campaigns (ore feed rates) over a given planning horizon under the assumption of deterministic mill throughput. A simulation model is used to evaluate the production plan under assumptions of stochastic machine failure and operational losses created by the need to cycle between input feeds. Campaign scheduling has two important implications for the simulation. First, during any campaign, multiple ore types may need to flow through the mill. However, the mill must be controlled to ensure that only one type of ore can be in a crusher, a grinder or a storage bin at any point in time. Second, as the mill switches from one campaign to another, the set of ores being processed may differ. Thus, the flow of ore through the equipment during a campaign changeover must be controlled to ensure that one or more of the ores from the current campaign can be completely eliminated before the ores from the new campaign are introduced.The simulation architecture employed for this project is Visual Basic for Applications (VBA) combined with MS-Excel as a user interface. A fixed step discrete event orientation is assumed as the simulation framework. A set of model constructs was built for the project with a specific Canadian milling operation in mind, but was designed to be representative of a broad class of milling operations. The constructs are implemented as class objects within the VBA structure, each with a number of properties and methods. The collection of VBA objects forms a composable modelling toolkit. These objects can be linked together by users, via MS-Excel, to represent a broad range of milling operations.

Sep 26, 2011

G. M. TAYLOR,* Colorado Springs, Colo.-The ore treated at the United Eastern is primarily a gold one and is cyanided-the counter-current decantation method being employed. One of our employees visited this plant a few months ago and, on his return, reported that the moisture in the tailing was carrying 20 c. per ton, which would appear to be somewhat high. As this type of plant has been advocated by one of the recognized cyaniding engineering firms in the country, and a number of these plants are in successful operation, it does not seem to me that the dissolved loss could be so high, and I would like to know if any one can give any definite information on this point? J. V. N. DORR, New York, N. Y.-I am very glad that Mr. Taylor has raised this question. When I first read Mr. North's paper and saw his statement, that they had an actual dissolved loss of 21.5 c. per ton, I was very much puzzled at this high loss which appeared avoidable by another decantation or the addition of a rotary filter. Reading it again, however, I noted that the actual dissolved loss of 21.5 c. given was evi-dently obtained by multiplying the assay of solution discharged from Z. thickener by the tonnage. On the basis of 283 tons milled per clay, this means $56.54 going to the clam. He states, however, that he returns from. the dam into the system, 70 tons daily assaying 40 c. per ton or $28 per day, so it would seem reasonable, unless I have overlooked something to regard the actual dissolved loss as $56.54 less $28 or $28.54, equaling 10.8 c. per ton. Even this loss, however, is much higher than good practice elsewhere, and can be accounted for largely by the tonnage being handled, which I believe is 30 per cent. above the capacity planned.

Jan 12, 1919

By Andre Vien, D. H. Hendriks, D. Willet, B. C. Flintoff

"For many years the training of mill operators was an informal process which involved senior operators training junior operators on an as-needed basis. Recognizing the needs and benefits of better training some companies, and even some provinces through legislation, have moved to ensure that a formalized training program exists in the plants. These programs tend to focus on basic safety and operations. Much remains to be done. With the more rapid incorporation of new processing and information technologies, and the goal to keep labour costs to a minimum by doing more with less, operator training has become a critical issue. This paper briefly examines the evolution of training programs, provides some measure of their effectiveness, and explores some recent developments which could have a very significant impact on the industry.PreambleOne can draw an analogy between operator training and the mechanical support of production equipment. When we buy a piece of process equipment it is critical that the mechanical installation be done properly to ensure that the device will operate at peak performance on start-up. Once the equipment is running, some form of preventive maintenance is required to ensure continued efficient operation. The operators and the equipment are both elements of the processing system, yet the former do not seem to get the same ""start-up"" or ""operating"" support. Are they not seen as critical to efficient operation? Why is this so? What impact does it have? How can we improve?These are all very logical and important questions, although the answers are not nearly so obvious. In the mineral processing industry, progress in operator training over the past thirty years has been limited and quite variable. To address the perceived need for a more coherent and consistent approach, some provinces have moved to incorporate basic training requirements in their legislation. Some plants have gone a few steps further by building integrated training programs into their operating culture. One conclusion which can be easily reached is that there are no standards, and that the range of training activity is great. In other words, a flotation operator is not a flotation operator is not a flotation operator. Their knowledge and skills are very much a function of training and experience, which are clearly corporate and site specific."

Jan 1, 1994

By P D. Munro

On the occasion of the 14th Mill Operators’ Conference and marking 40 years since the first one was held in Mount Isa in 1978, it is fitting to review the history of the Conference and its development over that time.The first 10 Conferences were irregularly held at three to four year intervals, with 9 of these in regional centres of Australasia. It is only since 2012 that the Mill Operators’ Conference has become a regular biennial event, alternating with the MetPlant Conference.The number of people attending the Conference has more than doubled to 470 delegates at the 13th one in 2016. It has outgrown its regional beginnings.Papers presented to the previous Conferences have been analysed according to commodity, country of origin, technology and theme plus the affiliation of the authors to discern any trends that may assist in planning the future events.Suggestions are made as to how the AusIMM might wish to arrange its mineral processing/metallurgical conferences.Recent changes to the structure of the Conference providing a more meaningful experience for the delegates and increasing their interaction and involvement should be vigorously pursued.CITATION:Munro, P D, 2018. Mill Operators’ conferences – a 40-year retrospective and a vision for the future, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 5–14 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By Peter Rubie, John Russell

"For many years, optimizing the relining of hard rock grinding mills has been complicated by the large number of variables, the low frequency of relines (resulting in a slow relining experience assessment and review cycle), and the potential economic risk associated with some changes to relining equipment or work practices. A technology that has its roots in the automotive manufacturing industry is being utilized to construct a statistically accurate, configurable, and dynamic simulation of the mill relining process. The detailed effects of various mechanization and process changes can be rapidly modeled and compared. Application of this discrete event analysis technology in the mineral processing industry delivers a range of benefits to many industry stakeholders. For example, mill maintenance managers and contract relining companies can embrace the opportunity to benchmark current performance against world’s best practice. Concentrator plant designers and mill manufacturers, informed by this technology’s scientifically defensible data set, can accurately plan for maximum plant efficiency when designing an infrastructure and equipment combination that truly maximizes annual plant availability. Time-motion studies of grinding mill reline data at mills of varying dimensions, liner configurations, mill relining equipment, operator and tool variables, have been integral to the development of this dynamic simulation tool and its associated data set. Access to mill relining simulation technology will enable mineral processing industry professionals to take advantage of an increased capacity to develop mineral concentrator performance optimisation initiatives within the given financial, physical and technological constraints of the individual concentrator plant."

Jan 1, 2014

By Reed S. C. Rogers

The breakage parameters of phosphate ore were determined by batch first-order grinding studies in a laboratory ball mill according to the procedures described in the text by Austin, Klimpel and Luckie, using a slurry density of 70 weight percent. The results were scaled to five larger mills of 0.56 m diameter by 0.91 m length (2 ft. by 3 ft.), 0.82 m by 1.52 m (3 ft. by 5 ft.), 3.36 m by 7.90 m (11.5 ft. by 25 ft.), 4.41 m by 9.10 m (14.5 ft. by 30 ft.), and 5 m by 11.1 m (17 ft. by 36 ft.), assuming equilibrium ball charges for the full-scale mills. The results were used to predict product size distribustions and capacities for batch grinding in the 0.56 m and 0.82 m diameter mills and open circuit grinding in the 0.82 m diameter and larger mills using a one-large/two-small reactors in series model fitted to the residence time distribution measured in the 4.41 m diameter mill. The simulated results were compared to plant data for ranges of mill capacities. It was found that the simulated product size distributions were in good agreement with the experimental values below the 70% passing sizes, but did not agree so well in the top sizes. The predicted capacities were in approximate agreement with experimental values for the pilot-scale mills, were about 7 percent too high for the 3.36 m and 4.41 m diameter mills and about 25 percent high for the 5 m diameter mill. Use of the Bond method with the measured Work Index of the phosphate ore gave capacity predictions that were 45 to 150 percent too high.

Jan 1, 1985

By The Mill Staff

Introduction The Hollinger cyanidation mill commenced operating in June, 1912, and 49,779,978 tons of solids had been discarded by the end of 1950. The present tailing disposal plant has been in operation since 1924 and holds 39,762,250 tons. The tailing disposal plant is on the property of Kayorum Gold Mines, Limited, about a mile and a quarter south of the mill. The area available for tailing covers 640 acres and is roughly l ¼ miles long by ¾ mile wide. Tailing was first deposited on the McKay veteran claims, l mile long by 1/2 mile wide, which were later included in the Kayorum property. This site sloped from northeast to southwest, the slope amounting to 106 feet between the northeast corner and the low land to the southwest. The low land was wet and a considerable area was covered with muskeg up to 17 feet deep. It was drained by a brook running across the property in a southwesterly direction. Later, when more ground was needed, the low-lying mining claims adjacent to the south and west boundaries were acquired to allow for the extension of the plant. This entailed some extra difficulties and expense that would not have been encountered had the whole of the present site been acquired with the original purchase. At the present time, the top of the tailing deposit stands at two elevations, but eventually the tailing deposited on the extension to the original plant will be raised to the same height as the older deposit. Previous to 1924, all of the tailing was deposited on Low land and in lakes near the mil1. Between 1924 and 1926 an increasing tonnage was sent to the McKay claims until, in 1926, all of it was being sent there. In 1936, the area of the deposit was extended and shortly afterwards all of the tailing was deposited on the new site.

Jan 1, 1951

By N Robb

This paper gives an account of the laboratory testing, plant testing and final inclusion of the two-stage sulphuric acid leaching process in the Milliken mill. Operational results for September, 1962, are presented, showing a uranium extraction of 95.5 per cent, with a saving of some 16 lbs. of 100 per cent H~S04 and some 9 lbs. of lime per ton milled. Methods for effecting further improvements in the process are indicated. HISTORY P RIOR to the incorporation of two-stage leaching, the process for the treatment of uranium ores at Milliken consisted of a single-stage sulphuric acid leach, followed by a solution recovery step involving washing in thickeners and two-stage filtration. The thickener overflow solution was subsequently concentrated and purified by ion exchange, and the uranium was recovered, by two-stage precipitation, as ammonium diuranate. Figure I illustrates this flowsheet. For satisfactory extraction of uranium from the. Milliken ore, a high residual acidity, of the order of 40 grams per litre of free acid in the discharge solution, must be

Jan 1, 1963

By David C. Cook

The milling complex, situated just east of the Cassiar townsite, receives raw ore from the tramline and processes it into 105,000 tons per year of milled asbestos fibre. The ore is passed through a concentrator, where a barren rock fraction is removed. The concentrated ore, representing 70% of the feed, is dried, stored and then milled into nine separate fibre classifications. The finished product is packaged into 100-lb bags and loaded into trucks in one-ton units. New air-handling facilities were added in 1977to provide additional air for environmental control.

Jan 1, 1978

By C S. Stevens

This paper describes the problems encountered and the steps taken to solve them in milling an ore containing relatively large amounts of pyrrhotite. A complex and greatly lengthened flotation circuit was required to recover the pyrrhotite. A very low pH had to be maintained in the cyanide circuit in order to get good recovery of the gold and maintain reasonable cyanide recovery. Introduction D ELNITE Mines Ltd., a gold mine situated about 5 miles by road south and east of the town of Timmins, Ontario, is serviced by two shafts. No. 2 shaft extends from surface to the 2875-ft. level, and No. 3 shaft, an internal winze, extends from the 2875-to the 5275-ft. level. No. 2 shaft was stopped at the 2875-ft. level because of a heavy band of chloritic schist which necessitated a drive to the north for 1000 feet, where No. 3 shaft was sunk. The latter bottomed in the schist at the 5275-ft. level. From the 2500 to the 2875-ft. level in No. 2 shaft, the ore was

Jan 1, 1965

The Hadsel Mill. By R. G HALL (Trans, vol 112 4000 words) This mill is designed to effect the entire reduction of ores by combined crushing and grinding from mine run size to material sufficiently fine for the usual operation of flotation or cyaniding The work is begun and completed in the same machine. The machine is designed on the principal of the elevator wheel, and crushing and grinding are accomplished by dropping a mixture of ore and water upon specially placed "breaker plates" in such a manner that the resultant material passes back into the buckets of the wheel for further elevation One method of removal of the finished product is to permit an overflow of wet pulp on one side of the mill through coarse screens A recent improvement provides for the removal of a pulp by a launder part way up the path of the buckets In either case the pulp passes to a classifier, and the oversize back to the mill in the manner familiar in ball-mill practice Although hardly through the development stage, the machine has given a very good account of itself in simplification of plant, by elimination of coarse and fine crushers with consequent reduction of installation cost and power consumption As compared with the ball mill alone, there is a reduction of power consumption as well as a material reduction of grinding steel There is an increase in cost of maintenance other than grinding steel, but as the machine passes out of the development stage there is a show¬ing of reduction of costs on this item It seems probable that with further develop¬ment and strengthening of the weaker parts further improvement may be made Ball Milling. By A. M Gow, M GUGGENHEIM, A. B. CAMPBELL AND W. H COGHILL. (Tech Pub 517; also Trans, vol 112. 24,000 words) This paper outlines a new philosophy in ball milling by using power as an index of mill operation and ascertaining the effects of the set and induced variables By recognizing the amount of ore in the mill as an important induced variable and recognizing that the amount of ore in the mill depends principally on the size of the discharge trunnion, ball volume, rate of feed, and speed of mill, obstacles formerly met were surmounted When the amount of ore in the mill is dealt with intelligently and the applied work is proportional to the amount of feed, series testing, which would otherwise give a hotchpotch, gives concordant results The study of ball paths and trajectories was seen to be fruitless when it was shown that the old attrition theory for slow mill speed

Jan 1, 1935

By A. M. Gaudin

The study that is presented here was undertaken in order to condense information concerning comminution, and covering a great variety of conditions, into one or several rules which would be of use in the development of a systematic theory as well as in many directly practical ways. As the result of this work, the following conclusions appear justified: 1. Rocks may be classified, from the point of view of comminution, into two general classes which are (a) structurally homogeneous, and (b) structurally heterogenous. Structurally homogeneous rocks are those in which fracture takes place through grains and grain boundaries alike; heterogeneous rocks are those in which fracture passes in preference through grain boundaries. 2. If a sized product composed of structurally homogeneous rock grains is crushed, a product results in which the relation between the percentage weight of grains of various sizes and these sizes themselves follows a definite law. This is not true of structurally heterogeneous rocks. 3. Ball milling with structurally homogeneous rocks, and under certain conditions, presents exceptions to this rule. 4. In ball milling with structurally homogeneous rocks, there exists a critical ratio of size of feed to size of balls, above which the machine operates essentially by surface wear, and below which it operates essentially by breaking across the body of the particle. 5. In ball milling, with structurally homogeneous rocks, and when the size of feed grains exceeds the critical size, the particles worn off are of a substantially definite size which depends upon the ball size. 6. In the case of a typical heterogeneous rock, such as Manhattan schist, particles are crushed in such a way that there is a greater proportion of grains of the size that is the average grain-size of the rock than there would be in that range of size with a structurally homogeneous rock. This has been found to be true with all the crushers tested. 7. Different methods of crushing produce grains of different shapes. 8. The importance of sizing the — 200-mesh portion of a crushed product, in crushing-efficiency investigations, has been greatly under-

Jan 1, 1926

By Bennett R. Bates

Nowhere in the world has cone classification in closed-circuit grinding with tube mills reached as high a state of development as on the Wit-watersrand. In the development of the Far East section the necessity of fine grinding to obtain satisfactory residues gave rise to a situation with which the cone could cope only at a great sacrifice in efficiency of tube-mill grinding. H. A. White1 recognized the limitation of the cone in his study of the theory of tube milling as early as 1915, but it was not until Ewing, Davis and Willey2 carried out their tests at Springs Mines during 1920 that the advantages of mechanical classifiers were demonstrated. During the fall of 1924 the writer supervised a series of tests with Dorr classifiers undertaken by Mr. White, Consulting Metallurgist, at the mill of the Geduld Proprietary Mines, Ltd., Dersley, Transvaal (Far East Rand). The importance of classification to obtain efficient tube-mill grinding was thoroughly demonstrated. The installation of classifiers of the above type that followed the test confirmed the results of the experimental work. Tests with Cones, Straight Type and Bowl Classifiers The test at the Geduld mill was made to determine the relative grinding efficiency of a tube mill when grinding in closed circuit with cones, straight type Dorr classifier and Dorr bowl classifier. The efficiency of a tube mill, as expressed in this article, is based on the tons of minus 200-mesh material produced by the mill. The efficiency is also expressed in terms of tons of minus 90-mesh material produced by the mills to correspond to the standard practice on the Witwatersrand. The results given for the performance of the tube mills grinding in closed circuit with cones (Fig. 1) were taken from previous tests carried

Jan 1, 1926

By Will H. Coghill

In this investigation, the low-grade red iron ores of Alabama were examined by the use of "heavy solutions."' Ores are generally ground preparatory to concentration and as long as the concentrators make suitable products the effectiveness of the grinding is likely to be unquestioned; but when suitable products are difficult to make, an investigation becomes imperative. In such a case a dissection of the ore might be made to find the cause of the trouble. Such a condition of unsuitable products exists in the low-grade red iron ores of Alabama. They are difficult to concentrate. To be sure it might be said that the concentration of iron ores is a new thing and that the ore-dressing methods are undeveloped, but a glance at the industry reveals an abundance of methods and devices for almost all imlaginable conditions. Concentrating machinery has not been tested in this investigation. When the properties of the ores have been gleaned, the machinery may be used more effectively. Alabama Low-grade Red Iron Ores The Bureau of Mines has undertaken by laboratory methods to select the best means of concentrating the low-grade iron ores of Alabama. These ores constitute the parts of the ore bed left by selective mining. If more of the ore bed could be included in the current output, the mining cost would be reduced and longer life of the district would be insured. This advantage would be reflected by added permanence of churches, homes, schools and every undertaking in the commonwealth. The red ores chosen for this study of effectiveness of grinding are too low in lime to meet the requirements of the blast furnace. If lime is

Jan 1, 1927

By J. P. Dick

THIS paper is a description of the milling practice and metallurgy at the Moneta Porcupine mine, Timmins, Ontario. The results obtained with an all-cyanide circuit and later with flotation followed by cyanidation are described. The ?investigation which prompted the various changes in milling practice have also been dealt with. Moneta ore is possibly the most refractory now being milled in the Porcupine district. This is due to the ultra fine state in which the gold occurs and to its intimate association with pyrite. No doubt there is ore of similar characteristics on the neighbouring properties but it probably forms only a small portion of the tonnage being mined, whereas at Moneta the bulk of the ore requires an extremely fine grind to liberate the gold. The fineness to which an ore can be ground economically has gone far beyond what was thought to be the limit only a few years ago. Formerly, a set of standard screens was all that was required to measure the fineness to which an ore was ground. At present, the Haultain infrasizer is practically indispensable, and the nominal micron has become a familiar unit of measurement to all those dealing with the problems of fine grinding.

Jan 1, 1941

By J. J. Mather

NEPHELINE SYENITE is a feldspathic rock resembling granite in texture and hardness but it is white in colour and contains appreciable quantities of the mineral nepheline, the result of a silica deficiency. It is relatively common, with known occurrences in Russia, Scandinavia, India, Canada, United States, and other parts of the world. However, the particular deposit being mined at Nephton, Ontario, by American Nepheline Limited is unique in its remarkable uniformity and low content of iron bearing minerals, both qualities essential in a ceramic raw material. The orebody is a pear-shaped mass over five miles in length, up to a mile in width, rising in three prominent ridges as much as 300 feet above the surrounding lakestudded terrain. American Nepheline holdings, consisting of 2,200 acres, comprise some 85 per cent of the total mass.

Jan 1, 1957