Search Documents

By E. vanHuyssteen

A method of establishing the relationship between the mineralogy of a sinter and its subsequent processing behaviour in a lead blast furnace is demonstrated. It involves: 1) analyzing the Zn-spinels, hardystonite, larsenite, Pb-silicates, Pb-arsenates, Pb-(Ca)-sulphates and other femtes with an electron microprobe; 2) determining the extent of elemental substitutions in various mineral structures; 3) establishing a sequence in which the various phases formed during sintering. In this manner the relationship between the bulk chemistry of a sinter formulation and the speciation of elements into various phases in the sinter can be established. Specifically, the-substitution of Mg for Zn in hardystonite significantly influences sinter production. Mg substitution releases Zn into the surrounding matrix. This Zn reacts with the Pb-silicate to form larsenite thereby reducing the amount of Pb-silicate available for anhydrite digestion. Excessive amounts of residual anhydrite thus result if the sinter formulation is based solely on the CaO/Si& ratio.

Jan 1, 1993

By T. T. Chen

This mineralogical study is based on samples from typical "wet" nickel laterites of humid tropical to sub-tropical regions. An in-situ nickel laterite sample from Goro and a transported laterite sample from Plaine des Lacs, New Caledonia, are predominantly limonitic. Two-thirds of the particles in the Goro sample are <10 um in size; they consist of skeletal goethite and serpentine, as well as minor amounts of talc, gibbsite, chlorite, quartz and clay minerals. The coarser grains are mainly Cr-spinel, serpentine, gibbsite and Mn oxide. Nickel occurs mainly in goethite, serpentine and Mn oxide; cobalt occurs in goethite and Mn oxide. The Plaine des Lacs sample is finer-grained and contains more Al and CO3, but less Mg and Si than the Goro material. The sample contains more kaolinite, chlorite, siderite and feldspar, but less serpentine and gibbsite than the Goro material. Nickel is detected mainly in goethite, serpentine, Fe-Mg silicate and Fe-Mn oxide. The Indonesian ore from Sorowako, as sampled from the reduction kiln feed containing some reverts, is predominantly saprolitic, with apparent particle sizes ranging from <100 um to > 1 cm. The sample of reduction kiln feed is rich in Mg silicates, Mg-Fe silicates and goethite, and exhibits complex alteration textures. The nickel contents vary from particle to particle. Nickel is present mainly in serpentine, olivine, chlorite and amphibole, and in subordinate amounts in goethite and Mn oxide. Cobalt is detected in the Mn oxide. Keywords: Nickel Laterite; Mineralogy; Nickel Carriers; Goro, New Caledonia; Plaine des Lacs, New Caledonia; PT Inco., Sorowaki, Indonesia

Jan 1, 2004

By A. I. Kogut

Impurity minerals in fluorspar ores and concentrates from a deposit in Southern Africa have been studied by reflected light, transmitted light, and cathodoluminescence microscopy. The principal impurities are quartz, calcite, aegirine, apatite, ankerite, magnetite, goethite, and synchysite [Ca(La,Ce,Nd)(CO3)2F]. Cathodoluminescence microscopy was found to be very useful in studying the character of the fluorite and especially for recognizing the presence of apatite and calcite impurities. Fluorite exhibits blue, calcite shows yellow, and apatite has white, light purple, and pink cathodoluminescence. The cathodoluminescent character of apatite varies with its geological environment and position in the orebody. The results of this microscopic study show that phosphorus present in fluorite concentrates occurs principally in binary locked apatite-fluorite particles. Successive fluorite cleaner concentrates contain progressively smaller amounts of locked apatite-fluorite particles. Free apatite has been effectively partitioned to the final tailings.

Jan 1, 1995

By Ari I. Kogut

Impurity minerals in fluorspar ores and concentrates from a deposit in Southern Africa have been studied by reflected light, transmitted light, and cathodoluminescence microscopy. The principal impurities are quartz, calcite, aegirine, apatite, ankerite, magnetite, goethite, and synchysite [Ca(La,Ce,Nd)(C03l2Fj. Cathodoluminescence microscopy was found to be very useful in studying the character of the fluorite and especially for recognizing the presence of apatite and calcite impurities. Fluorite exhibits blue, calcite shows yellow, and apatite has white, light purple, and pink cathodoluminescence. The cathodoluminescent character of apatite varies with its geological environment and position in the orebody. The results of this microscopic study show that phosphorus present in flUorite concentrates occurs principally in binary locked apatite-fluorite particles. Successive fluorite cleaner concentrates contain progressively smaller amounts of locked apatite-fluorite particles. Free apatite has been effectively partitioned to the final tailings.

Jan 1, 1995

By J. W. Cash

The mineralogy and textures of cyclone dust, sludge, and occasional build-ups in the American Iron and Steel Institute (AISI) direct iron making pilot plant at Universal, Pennsylvania have been studied by reflected light, transmitted light, and cathodoluminescence microscopy, and phase compositions have been determined by SEM-EDS. The cyclone dust consists of particles of carbon, metallic iron, sulfur-bearing iron, and wustite. Measurements of particles in the sludge indicate that 69% are less than 2.5 µm across, 21 % are 2.5-5 µm, and 10% are larger than 5 µm. Mineralogically the sludge particles are mainly carbon and metallic iron, with minor wustite and sulfur-bearing iron. Build-ups that sporadically develop in the furnace consist of olivine, hercynite spinel, metallic iron, wustite, pyrrhotite, pseudobrookite, akermanite-ferroakermanite and gehlenite. The microtextures shown by the build-ups indicate that much of that material has precipitated at the build-up loci. This study has been supported by AISI and the U.S. Department of Energy.

Jan 1, 1995

By Shobha Kumari

Coal is the prime source of energy in India. It now contributes to about 55% of the total power generation and will continue to have its major share in the energy mix of the country in the foreseeable future. Thermal coals of India, known for their wide variations in nature and categorized as difficult to wash due to their typical mineral matter association with the organic matrix, need suitable beneficiation technique for quality upgrade for improving the overall economics, efficiency and pollution free power generation. A non-coking high-ash coal, collected from Vasundhara open cast mine of the Ib Valley Coalfield, Orissa, has been characterized along with its different fractions obtained in the process of beneficiation for distribution of minerals using FTIR, XRD and ash analysis. The raw coal was fractionated by size as well as by density. It has been observed that ash yields and mineralogical composition (found to be mainly kaolinite and quartz) have no appreciable change in different size fractions, indicating homogeneous distribution of minerals in the coal matrix. However, for the different density fractions the mineral composition and ash yield have significant variations. The quartz content of the beneficiated coal visualized with 34% ash yield, as mandated by the Ministry of Environment and Forest (MOEF) for the use of coal in power plants is reduced to half of that of the raw coal. As quartz is the most abrasive mineral in coal, reduction of its proportion obviously signifies considerable reduction of wear of power plant machinery when beneficiated coal is fed to utility boiler for generation of power. The composition of the major minerals quartz and kaolinite as determined, also favors formation of ash of refractory nature during combustion. Keywords: IB valley coal, beneficiation characteristics,

Sep 1, 2012

By Yugo Mitani, Tatsuya Kato, Chiharu Tokoro, Abdullah Al Mamun

Acid mine drainage (AMD), which is a major source of mining pollution, often contains ferric and/or ferrous ions together with several toxic elements. The ferric and ferrous ions in AMD precipitate in several mineralogical forms after neutralization, and the ferric/ferrous precipitates become the main component of the sludge generated after AMD treatment. The precipitates are also good absorbents for several toxic elements. To avoid generation of voluminous sludges and the re-dissolution of toxic elements from the sludge, it is very important to generate well-draining and efficiently adsorbing sludges by controlling the mineralogical form of the ferric/ferrous precipitates. Green rust, which is ferric and ferrous hydroxide, is a double layer hydroxide which is able to sorb several toxic elements. The green rust transforms to goethite or lepidocrocite by rapid oxidation, whereas it transforms to magnetite at ambient temperature by slow oxidation. The magnetite is also good absorbent especially for toxic cations and it makes a compact sludge due to its magnetic properties. We investigated the magnetite generation process at ambient temperature in detail. The magnetite generation process can be divided into three steps; (i) oxidation of Fe(II), (ii) Fe(II) surface complexation to Fe(III) hydroxide, and (iii) crystallization of magnetite. More magnetite can form when the oxidation rate is slower than the crystallization rate, and optimum conditions for its formation are at pH 9.5 with mild agitation. Ferrihydrite is the most common precipitate and it is able to sorb many different toxic elements. However, it drains badly and its solid/liquid separation properties are poor. We investigated the removal mechanism of several toxic elements by co-precipitation with ferrihydrite. We confirmed that the removal mechanism by co-precipitation partly involved surface precipitation when the initial ratio of toxic elements to ferric ion was high, although the main mechanism was always surface complexation. When surface precipitation occurred, highly efficient toxic element removal with ferrihydrite could be achieved.

Jan 1, 2016

During foundry sand reclamation process development, molds formed from reclaimed chromite sand showed a rapid decline in tensile strength during thermal cycling tests. Because this characteristic could limit reuse of chromite sand in the foundry, the sand was examined in detail. Scanning electron microscopy, x-ray mapping, magnetic susceptibility, and x-ray diffraction were utilized to evaluate processed chromite sand. It was found that process variables such as binder composition, reclamation temperature, and processing method had a significant effect on the chromite sand particle surface. X-ray diffraction indicated a crystallographic change in the processed sands. Magnetic susceptibility also increased after processing. Diffusion of iron to the particle surface and increased surface roughness were identified as potential causes of the decreased tensile strength in the molds.

Jan 1, 1993

By R. Kramer

During foundry sand reclamation process development, molds formed from reclaimed chromite sand showed a rapid decline in tensile strength during thermal cycling tests. Because this characteristic could limit reuse of chromite sand in the. foundry, the sand was examined in detail Scanning electron microscopy, x-ray mapping, magnetic susceptibility, and x-ray diffraction were utilized to evaluate processed chromite sand. It was found that process variables such as binder composition, reclamation temperature, and processing method had a significant effect on the chromite sand particle surface. X-ray diffraction indicated a crystallographic change in the processed sands. Magnetic susceptibility also increased after processing. Diffusion of iron to the particle surface and increased surface roughness were identified as potential causes of the decreased tensile strength in the molds.

Jan 1, 1991

By R. Y. Wan, S. L. Chryssoulis

"Gold associations were established in a·biooxidized, chlorinated CIL residue assaying 0.02 oz Ault and in a biooxidized thiosulfate leach residue assaying 0.01 oz Au/t. A detailed mineralogical study involved: assays of screened fractions; light microscopy; ion probe microanalysis to quantify 'invisible' gold in sulfide minerals; proton probe microanalysis to detect and quantify preg-robbed gold. In the CIL residue, most of the gold is preg-robbed (71 %). In the thiosulfate leach residue, gold occurs mainly as submicroscopic disseminations in microcrystalline quartz (chert). In both residues, the 'invisible' gold in pyrite accounts for a minor fraction of the gold assay. Quantitative determination of the gold occurrence in the two residue samples established conclusively that gold adsorption on carbonaceous matter in the thiosulfate leach is of minor importance.Acknowledgement: published with permission of Newmont Gold Company."

Jan 1, 1997

By William Petruk

Many gold operations lose gold during processing because some ore characteristics which affect recoveries have not been determined, and consequently the plant could not be designed to account for them. The ore characteristics can be determined with mineralogical techniques by analyzing the plant feed, final tailings and mill products. The plant feed and/or final tailings are commonly analyzed first as a separate project. Mill products are analyzed only if the process employs a minerals separation circuit to produce a concentrate (e.g. secondary flotation circuit to concentrate gold-bearing arsenopyrite), and if assays and materials balances indicate a recovery problem in the minerals separation circuit. Many ores have been evaluated at CANMET on a confidential cost-recovery basis by custom-designing a work plan which was dependent upon the problem and on the characteristics of the ore. The reasons for gold losses have been identified in most cases, and suggestions for modifying flowsheets have been proposed. The methods used in performing the analyses are described in this paper, and non-confidential results from in-house projects are provided as examples of the benefits of such analyses. The analytical methodology involves a combination of the following procedures: -producing heavy mineral concentrates and identifying the gold minerals in the concentrates; -determining quantities of invisible gold in gold-bearing sulphides, sulpharsenides, etc. by SIMS; -determining quantities and liberation characteristics of all gold minerals and gold-bearing minerals in the sample; -finding and identifying gold minerals in silicates; -extensive grinding and cyanidation to determine the ultimate amount of cyanidable gold; -determining impact of clay minerals and graphite; -performing a mineral balance for the gold in each sample; -performing a materials balance to determine the distribution of the gold minerals, gold-bearing minerals, and other minerals throughout the flowsheet, and; -interpreting the results.

Jan 1, 1995

The paper presents results of the mineralogical examination on samples from a bacterial leaching test which simulated in situ leaching for 482 days. Rock fragments (15 to 20 cm) were obtained from the top, the middle and the bottom of a bioleach column. Examination of the samples was carried by electron microscopy and image analysis. The surfaces of the rock fragments were studied to characterize the precipitation products, and cross-section cuts were studied to assess the advance of the bacteria leaching front and the dissolution of the different sulphide minerals.

Jan 1, 1991

By Ricardo Oliveira Gallart de Menezes, Claudio Gerheim Porto, Reiner Neumann

This study presents the results of the mineralogical characterization of Ti-Zr ore from the Jiboia deposit, located in the municipality of Brejo Grande, Sergipe State, Brazil. The goal is to identify the main Ti, Zr, and REE carrier phases in the different particle size fractions in order to subsidize the development of a cost-effective processing route for the production of heavy minerals concentrate. The mineral resources are estimated at 31.5Mt @ 3.5% of total heavy minerals (THM) for the Jiboia Ti-Zr deposit, of which 5 Mt @ 3.39% THM were classified as measured and indicated. The mineralogy of the heavy mineral concentrate recalculated to 100% is represented by 22% pseudorutile, 20% ilmenite, 15% zircon, 5% rutile, 2% monazite, and 36% gangue. The ore minerals are preferably concentrated in the 150 × 53-μm granulometric fractions, which represents 80% of the THM and only 27% of the ROM (Run-of-Mine) ore. Therefore, by cutting the ore to 150 μm, it is possible to discard 73% of the ROM mass and recover 80% of the THM, including 100% of the zircon and monazite which are the most valuable minerals present in the heavy mineral concentrate. The global recovery of THM starts to decline rapidly in the fractions finer than 106 μm and the mass disposal (tailing) does not follow in the same proportion. Higher zircon contents in the concentrates of the fractions finer than 150 μm imply a significantly lower recovery of heavy minerals like ilmenite, pseudorutile, and rutile that make the fractions coarser than 150 μm.

Jan 9, 2024

By L. Stamenov, H. Bouzahzah, S. Gaydardzhiev, D. Naumov

"The Chelopech epithermal arsenic bearing high-sulphidation, copper-gold deposit located in Bulgaria is often referred as the richest European gold deposit currently under exploitation. Key points from the flotation circuit of the processing plant have been sampled and selected physicochemical parameters measured. Plant survey has followed with selected samples being submitted to chemical and mineral liberation analysis (MLA). Quantitative analysis has enabled to link the flotation response of the main copper bearing minerals with the physiochemical parameters (Eh, DO, EDTA extractable Cu and Fe) being measured. Data from mineral liberation analysis have highlighted an important process-relevant information explaining the variable floatability in the various granulometric classes.The low chalcopyrite recovery could be linked to the non-sufficient amount of dissolved oxygen measured in the copper selective flotation circuit. Given the finely-disseminated copper bearing minerals, the observed copper losses inside the flotation could be also explained by the insufficient degree of liberation of the mineral grains. Suggestions for improvement in metallurgical recovery are therefore proposed.INTRODUCTIONThe Chelopech deposit is a high sulphidation (HS) volcanic-hosted epithermal gold-copper one (Bonev et al., 2002; Kouzmanov et al, 2009; Strashimirov, et al. 2002). It is considered as one of the largest and economically most important ore deposits in Bulgaria, and often is referred to Europe’s largest currently mined gold resource. It is located in the Srednogorie zone which falls within the central sector of the extensive Tethyan–Eurasian copper belt formed during Mesozoic–Cenozoic time along the southern margin of Eurasia. The Srednogorie zone has the features of a subduction-related, Late Cretaceous island arc, with development of a calk-alkaline to sub-alkaline volcano-plutonic magmatism and associated hydrothermal ore deposits (Bonev et al., 2002).Ore mineralisation occurs as veins, mineralised breccia, and massive sulphide replacements and disseminations. Three mineralisation stages have been identified at Chelopech deposit. An early pyrite–marcasite mineralisation (stage I), characterised by disseminated to massive pyrite followed and partly brecciated by enargite– luzonite and tennantite–chalcopyrite–bornite (stage II) mineralisation. The gold is met in ores belonging to the stage II. Sphalerite and galena veins characterise stage III, best developed below and adjacent to the pyrite–enargite– chalcopyrite ore bodies. Advanced argillic altered volcanoclastic rocks commonly host this mineralisation (Chambefort and R. Moritz, 2014)."

Jan 1, 2018

By A. Makavetskas

"The purpose of the research is to study the mineralogical features of the structure of the wall accretion formed during melting on the working surface of the walls of metallurgical aggregates and adversely affect the stability of the lining of blast furnaces (BF). We presented the results of studies of the material composition of lining and wall accretion of the furnaces of blast furnaces of the metallurgical plant specializing in the smelting of ferromanganese, nodular and pig iron. It is established that the garnissage is an aggregate of layered texture, formed as a result of the crystallization of slag and metallic melts. Refractory calcium and magnesium silicates and aluminosilicates (minerals of the melilite group, leicite, olivine group minerals) and amorphous glassy oxide solid solutions of variable composition crystallize from the slag melts in the upper part of the hearth. In the slag matrix, inclusions of carbon (amorphous and graphite) and products of crystallization of metallic melts of alpha-iron, iron carbides and / or manganese are observed. Evidence of carbon evolution (in the form of graphite) is precisely in the crystallization of metal melts, there are significant differences in the structure of carbon in coke and in the garnissage. The conducted studies confirm that it is impossible to obtain reliable information on the material composition of new formations in the blast-furnace process without using a complex of modern methods of technological mineralogy.INTRODUCTION The formation of the wall accretion (garnissage) - a solid protective layer as a result of smelting products crystallization on the inner (working) surface of the liner. This is due to the design of blast furnaces with a high-efficiency heat sink using copper coolers and the use of carbon blocks with high thermal conductivity in the lining. The objective of the study was research of the material composition of the lining and wall accretion of the blast furnace hearth of one metallurgical plant that specialized in smelting ferromanganese, nodular and pig iron, to assess the effect of new formations for stability of the lining of blast furnaces (BF)."

Jan 1, 2018

By Paul F. Kerr

The insufficiencies of our mineral resources are becoming well known, and the national political conscience seems to be troubled at last by our dependence upon mineral commodities which must come from other lands. This realization places increased responsibility upon the industrial, educational, and governmental groups whose task it will be to solve the problems of mineral supply. As we all know, from the time that man first sought mineral deposits until recent years, prospectors have been largely responsible for mineral discoveries. Today the era of the prospector is almost over. The human ants that have literally examined all accessible outcrops and have tested the gravels of nearly all stream beds in the United States have left undiscovered few worthwhile mineral deposits within the scope of their recognition. The pages in the history of mineral exploration are now being turned from the era of the surface prospect to the era of the hidden de- posit.

Jan 1, 1949

By P. M. Swash

The determination of the heavy minerals in beach sand samples is highly dependent on the preparation technique used. In this paper a simple reproducible method for the quantification of "recoverable" ilmenite, zircon, rutile and leucoxene by magnetic separation, is described. The procedure recommended yields information relevant to the metallurgical processing of the ore rather than to the total heavy minerals present in the samples. Finally the determination of mineral reserve estimations and grade assessments is greatly facilitated when this "mineral assay" method is employed. An assortment of other mineralogical methods are described including SEM, EMPA, XRD, XRF, Image analysis, Mossbauer. clerici and perm roll separations. The methods are briefly examined and the practical information that can be gained by using such techniques are reviewed. Experience has shown that an understanding of the relationship between the physical and chemical properties of the heavy minerals can contribute to the prediction of mineral particle behaviour. Such information may ultimately help reduce the prospect evaluation period and minimise expenditure on metallurgical testwork.

Jan 1, 1991

By T. T. Chen

The behavior of gold in a conventional copper electrorefinery anode slimes treatment process is expounded on in this study. In the raw anode slimes generated in a copper electrorefinery, gold occurs mainly as tiny particles of metallic gold, which are commonly attached to selenide particles. Some gold is also present in selenide form. Decopperizing the anode slimes retains much of the metallic gold, but also promotes the incorporation of gold in the structure of silver-rich selenide species. A greater fraction of the gold is converted to (Ag,Au)2Se or Ag3AuSe2 when high-Se and high-Ag anode slimes are decopperized at elevated temperatures and pressures. After pelletization and roasting of the slimes, the gold is converted to a (Ag,Au)-alloy and Ag3AuSe2. Smelting of the roaster products eliminates the selenium and converts the gold to a silver-rich (Ag,Au,Pd)-alloy in the dore metal. In the subsequent silver electrorefining process, gold collects as a gold-rich (Au,Ag,Pd)-alloy in the gold mud. Dore smelting rejects many impurities as a silica slag; minor amounts of gold are present as a (Ag,Au,Pd)-alloy in the silica slag. This gold is recovered by flotation and is recycled to the dore furnace. Gold is identified in both the tellurium caustic leach residue and the parting plant wash water mud as tiny particles of metallic gold. These products are also recycled to the dore furnace to recover their gold values.

Jan 1, 2008

By S Hapugoda, J Manuel, E Donskoi, L Lu

Sinter can constitute up to 80–85 per cent of the total ferrous burden in modern blast furnace ironmaking operations. The mineralogy and microstructure of iron ore sinter play an important role in determining its physical and metallurgical properties. As a result, characterisation of sinter phases is a cost-effective and complementary tool to conventional physical and metallurgical testing of iron ore sinter in evaluating and predicting sinter quality. Over the years, CSIRO has developed a scheme for characterising iron ore sinter that classifies primary sinter phases such as unreacted and partially reacted hematite and magnetite, and secondary phases, including prismatic high-temperature silico-ferrite of calcium and alumina (SFCA), microplaty SFCA (SFCA 1), dense SFCA, secondary hematite and magnetite, glass, larnite (dicalcium silicate; Ca2SiO4) and remnant fluxes. Quantification of these phases has traditionally been carried out by manual point counting under a petrographic microscope; however, new technologies based on automated optical image analysis, quantitative X-ray diffraction and scanning electron microscopy are now available for evaluation. In this study, two sinter samples of varying chemistry were prepared and characterised using both point counting and automated optical image analysis. The implication of the results obtained for the performance of different quantification methods is also assessed.CITATION:Hapugoda, S, Lu, L, Donskoi, E and Manuel, J, 2015. Mineralogical quantification of iron ore sinter, in Proceedings Iron Ore 2015, pp 35–44 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By J. -M. Milazzo, T. Wallmach, S. B. Blancher, A. Amalric

In a FeNi electric arc furnace, the physical properties of the slag (chemistry, viscosity, liquid/solid/gas ratio) are of crucial importance in controlling the efficiency of the process. In this paper, we studied the slag crystallised on the walls of a semi-industrial furnace (freeze-lining), the slag rising through the burden during foaming phenomena, and the casted slag. The freeze-lining is the layer of oxides that crystallises on the refractory wall of a furnace, protecting it from chemical and mechanical aggression. It records changes in furnace conditions (slag chemistry, temperature, oxygen fugacity), which makes it possible to observe the impact of these elements. In the high reduction test, the freezing lining is composed of magnesian olivine. Switching to a low reduction process increases the Fe content of the olivine and causes orthopyroxene to appear, making the freeze-lining mechanically and thermally weak. Thermal incidents in the furnace cause significant slag foaming. This foaming is produced by a massive crystallisation of the olivine (due to the drop in temperature), and inducing an exponential increase in viscosity, preventing the free circulation of gases. These foaming episodes are also recorded in the freeze lining and form layers rich in gas bubbles, and therefore mechanically fragile. The slag casted and cooled in a ladle allows the first steps of slag crystallisation to be studied. Olivine is the liquidus phase, with a magnesium-rich core and an iron-enriched rim, contemporaneous with the orthopyroxene phase. The habitus of these phases is very similar to that found in komatiites for the same minerals. FeNi slag is therefore an industrial analogue that is easy to study and compare to komatiites. Keywords: Pyrometallurgy, ferronickel, slag, freeze-lining, characterisation, olivine, mineralogy

Jan 1, 2020