Search Documents

By Arthur G. Levy, Henry M. Howe

$1. Introduction.—Any given piece of metal is made up of a very great number of grains, usually microscopic, each of which is a perfect crystal save only in outward form, with cleavage planes of low cohesion, geometrically arranged quite as in fie familiar non-metallic crystals. The plastic deformation of such a mass occurs chiefly through the slipping of the crystalline blocks of which each grain is composed along these cleavage planes, causing steps called slip bands to form on a previously polished surface. In this slip, the metal immediately adjoining each of the cleavage planes along which the slip takes place is thought to pass extremely rapidly through a very mobile state into the amorphous state, in which it is harder than the remaining still crystalline metal between the amorphous layers thus formed along the slip planes. Whether the slip planes below the surface in ferrite can be detected by cutting, polishing, and etching sections is in dispute; but if this detection is possible at all, it is usually made impossible by heating the metal even gently. In short, the change along the slip planes does not persist through heating, and it is thought not to persist through time even at the room temperature, nearly all the amorphous metal recrystallizing. The network in Fig. 22 and the parallel N.-70-E. lines in Fig. 21 are slip bands in copper. When plastically deformed metal is heated, certain parts of certain grains may twin, that is, their component crystalline units may rotate into a position, or more exactly into an orientation, symmetrical with the initial orientation and hence with that of the remainder of that grain. As seen in a microsection of a metal the twinned areas usually have parallel sides. The existence of twinning is recognized in metallic sections either by the presence of such parallel-sided areas differing in brightness from the adjoining metal, especially when seen under oblique light after etching, or more surely by the zigzagging of the slip bands which form when twinned metal is itself deformed again. Hence the usual procedure in developing twins is to deform plastically so as to cause the twinning tendency; to heat so as to allow the tendency to assert

Jan 1, 1915

By John A. Mathews

It is a great honor to be asked by the Board of Directors of this Institute to deliver the Henry Marion Howe lecture. The invitation carries with it a great responsibility, which I accept with considerable hesitation and with a feeling of unworthiness to perform the duties expected of me in this hour devoted to the memory of the life, character, and work of the late Professor Howe. Many of you recall the scholarly address delivered here a year ago by Prof. Albert Sauveur, and the beautiful tribute he paid to his friend and colleague of many years in the great work of changing the art of iron making into the science of iron. My association with Professor Howe was of brief duration—only one year—and the relation was that of pupil to teacher. My feeling toward him in later years was always that of a humble disciple at the feet of a master. He attained his third academic degree in the year that I was born. I recall the pride I felt when, after entering the steel industry, I received from him, from time to time, letters asking for information or, perchance, asking my opinion, and he was always most punctilious in acknowledging the source of such bits of information in his writings. It was also my good fortune to sit at the feet of another great teacher— Sir William Roberts-Austen, at the Royal School of Mines. I mention him because his name was used by Osmond in coining the word "aus-tenite," which is the subject of this address, and Osmond's suggestion was heartily approved by Howe. These three international metallurgists were the best of friends and delighted to honor the achievements of one another. There are other reasons for mentioning Roberts-Austen at this time. It was an introduction from Howe that opened to me the door of his laboratory as well as of his heart. It was while at Roberts-Austen's laboratory that I worked side by side with William Campbell

Jan 1, 1925

By J. Sharshall Grasty, Thomas L. Watson

The users of barite in the United States derive their supply partly from the domestic production and partly from the imports from foreign countries. According to the Mineral Resource division of the U. S. Geological Survey, the domestic production of barite in 1913 was 45,298 short tons, valued at $156,275, or $3.45 a ton, and the imports of crude barite were 35,840 short tons, valued at $61,409, or $1.71 a ton. These figures clearly show a decided advantage in cost of the foreign over the domestic barite to users in the United States. The difference in cost is the only advantage to the consumer of foreign barite, for there are large reserves of the mineral in the United States of good grade. The production of many of the operating mines is capable of decided increase, and it is believed that the operating mines together with the large reserves of undeveloped deposits of barite are entirely adequate to meet the demands of the users in the United States. Deposits of barite are known in California, Idaho, Nevada, and Alaska, but most of them are undeveloped because there is, apparently, no market for the material in that region. The domestic production is derived from Missouri .and the Appalachian States, the greater part being obtained from Missouri. Following the outbreak of war in Europe many users of foreign barite in the United States have been forced to seek their supplies at home. It seems opportune at this time, therefore, that a general review be given of the barite industry in the Appalachian States, one of the two areas from which the domestic supply of the mineral is derived, and that attention be directed to the undeveloped deposits in the region. Briefly, then, this paper reviews the barite industry in the Appalachian States, and describes the occurrence, preparation, and uses of the mineral. General Character Barite, known commercially as barytes or heavy spar, is barium sulphate (Baso4), containing when pure BaO, 65.7 per cent., and S03, 34.3 per cent. The specific gravity is 4.3 to 4.6, and the hardness 2.5

Jan 1, 1915

By G. H. Alvey, A. W. Foster

The measure of value of an oil property is approximated by the length of time it takes to "pay out;" viz., the time required for it to return the original investment. This time varies in different fields. In the Appalachian and Mid-Continent fields, a good investment pays out in about four years; in California, it requires a slightly longer time; and in the Gulf field about two years. The two principal methods for establishing these values are based on acreage, as in California, and on production, as in the Appalachian field. The method of establishing values based on production1 was worked out in the Appalachian fields and approximates the value remarkably well in some fields; but it is a rule of thumb and should be used intelligently. Briefly, the method is as follows: An arbitrary number of dollars (called the barrel-day price) multiplied by the number of barrels of settled daily production of the property gives the value. In its crudest application, the barrel-day price is determined by the "$10 to $0.01" rule, which means that the barrel-day price is one thousand times the prevailing price of oil. For instance, with oil at $3.50 per bbl. the barrel-day price would be $3500 per bbl. This rule, however, is not strictly applied, for the barrel price is varied according to whether or not the wells "hold up." But when a barrel price for a district has been fixed it is quite general to raise or lower the price with the fluctuation in the price of oil; here the"$10 to $0.0l"ruleisused extensively. However, the prospective purchaser takes into account tangible equipment upon the property, the extent to which the drilling program has been carried out, whether or not the wells are "shot" or natural, depth of wells, spacing of wells, paraffin trouble, etc. The basis of this method is settled production. As soon as production is considered settled, a flat barrel-day price is generally applied to all properties, no matter what their age. If it were possible to show that this flat rate was erroneous and that the value of the property depended on the point on the decline curve at which the wells happened to be (in other words, their age), and also on the operating costs, the future price

Jan 1, 1921

By Albert Sauveur

Floris Osmond, Honorary Member of the American Institute of Mining Engineers, born in Paris, March 10, 1849, died at Saint-Leu near that city, June 18, 1912. Taken suddenly ill with congestion of the brain while on his way from Paris to his home, he reached it in time to write on the typewriter his last wishes, one of which was that no biographical notice of his life should be published. Holding Osmond's memory sacred, as those who have known him will, is it our duty to conform with his desire ? Shall no mention be made in our Transactions of the beautiful life and great achievements of one of our most honored members? Is it not, on the contrary, incumbent upon us to disregard Osmond's instruction in this matter and to place on record our admiration for the nobility of his life, for his talents and for the importance of his work, that younger men may be inspired by it with a desire to be guided by worthy motives in the path of unselfish pursuits ? I cannot feel that in following this course I am disloyal to Osmond's memory and I am strengthened in this belief by the opinion of men of high honor whom I have consulted before undertaking the writing of this obituary notice. One of them, Professor Henry M. Howe, justifies my decision better than I could do it myself when he writes : " Let us look frankly at the matter. Here we have a most extraordinary life, a life of rare beauty and power of inspiration to the rest of mankind. In my opinion we should not deprive mankind of the stimulating influence of the example of M. Osmond simply because he shrank from publicity. Our young men see every day how greed and vulgar push succeed, and with what material rewards they are crowned. They see too rarely the more valuable crown which comes to self devotion. A permanent and public recognition of the beautiful qualities of Osmond's life cannot fail to appeal to the imagination of young men and to help to deflect them toward leading a noble rather than a sordid life. Therefore I feel that the Revue de Métallurgie and other bodies owe it to the public to give prominence to his career by means of biographical notices."

Jan 1, 1914

The Iron and Steel Committee of the American Institute, of mining and Metallurgical Engineers held a joint session with the American Foundrymen's Association during the Annual Meeting of the Institute in February, 1928, for the purpose of discussing blast-furnace operations and the character of pig iron and castings. Dr. Richard Moldenke presided. H.. H. Sweetser, who was named on the program as the presiding officer of the session, was unable to be present, but sent a letter in which he said: " The meeting we had here last year and the meeting held in Chicago last June showed a desire on the part of blast-furnace men and users of pig iron to get the facts regarding the influence on castings made from pig iron produced in blast furnaces under varying conditions of temperature, mixture and local furnace operations. It has been my hope that at this Round Table we might he able to formulate a series of tests that, would give us the desired information. "Several independent blast-furnace investigations have. been, and still are being, carried on in different sections of the country. The furnaces investigated include a southern furnace, a middle-west furnace, a western furnace and a Chicago district furnace. The results so far show distinct characteristics for each of the four furnaces. It is possible that a furnace in the eastern part of the United States would be different from all the others. "It is hoped that a plan of action can be worked out at your meeting today whereby the IT. S. Bureau of Mines will be able, to carry on more extensive work in connection with the research departments of the different iron and steel companies and the big consumers of pig iron. "No one group can get all of the, information but if the different investigations can be coordinated it will he possible for us to (Iran. conclusions regarding the effects of varying conditions in blast-furnace practice on the pig iron produced and the castings made there from." DISCUSSION R. Moldenke, Watehung, N. J.—I was across the -water this summer and saw some of those interested in an investigation of this kind. 'I'hey told me that in Germany, where they had a joint committee of blast-furnace operators and foundry-

By M. A. Hosmer, Job Goostray, R. F. Harringon

In this paper, as in so many discussions of an historical nature, there is little chance for original material and much has had to be rewritten from older papers, documents, accounts, reports, and the like, some of which are of doubtful authorship or contain conflicting statistics. Fully aware of these pitfalls, the authors have tried to quote the origin where possible, and also to seek further confirmation when the statement warranted it, but they cannot assume responsibility for certain facts and dates. The Encyclopedia Britannica was frequently consulted. The authors wish to acknowledge assistance from Mackintosh-Hemp-hill Co. (formerly the Fort Pitt Works) and also from officials of the Watertown Arsenal who loaned valuable books and gave much necessary information. They are particularly indebted to Colonel Dickson of that institution. The data on modern guns were furnished by Mr. F. Brauer of the Watertown Arsenal; Mr. H. S. Chaffee assisted by obtaining records and data of work carried on by the Builders' Iron Foundry of Providence, R. I. Three Epochs in History of Cannon Among the great industries of New England, the manufacture of iron was the first to receive attention. Iron ore in considerable quantities was known to exist within the territory of the Massachusetts Bay Colony; and as early as 1629 some steps appear to have been taken toward the manufacture of iron by the Court of Assistants in London, under whose patronage the colony was founded. During the next ten years, deposits of bog ore were found in numerous ponds in the Plymouth Colony; and, in 1652, iron manufacture was begun at Raynham. The "Old Colony" was known as the main seat of this industry in New England, out of which grew a concern which was later to become one of the principal

Jan 1, 1925

By P. E. Demmler

The apparatus in which the process of bright annealing of copper wire was carried out consisted of a section of iron pipe, 6 ft. long and 3 ft. in diameter. The pipe was provided with flanges to which were bolted the end plates for sealing, also with inlet and outlet tubes to allow for the displacement of the air in the pipe by natural gas. After charging with copper wire, sealing and displacing the air, the pipe was heated to 350' C. (662" F.). It was expected that the natural gas would furnish a neutral atmosphere which would prevent oxidation and give a satisfactory bright-annealed product. It was found, however, that the outer layers of wire were discolored and not suited for the use for which they were mtended. To obtain an idea of what was taking place in the annealing furnace, skeins of the hard-drawn wire were placed in a glass tube so that all changes in appearance could be observed as they were heated to different temperatures and under varying conditions. The temperature in each case was determined by means of a thermocouple placed in the tube close to the wire. Following is a summary of the results of these experiments: 1. When the wire was heated for 1 hr. in a current of natural gas at a temperature of 350") 400") or 500" C. (662", 752", or 932" F., respectively), there was a marked darkening of the wire throughout the skein. 2. When heated for 1 hr. in natural gas at a temperature of 600" C. (1112' F.), there was no coloration, the wire remaining clean and bright. 3. When heated in natural gas to 350" C. until darkened and the treatment continued with the temperature raised to 600' C., the coloration disappeared and the wire became clean and bright.

Jan 1, 1923

By P. E. Demmler

The apparatus in which the process of bright annealing of copper wire was carried out consisted of a section of iron pipe, 6 ft. long and 3 ft. in diameter. The pipe was provided with flanges to which were bolted the end plates for sealing, also with inlet and outlet tubes to allow for the displacement of the air in the pipe by natural gas. After charging with copper wire, sealing and displacing the air, the pipe was heated to 350' C. (662" F.). It was expected that the natural gas would furnish a neutral atmosphere which would prevent oxidation and give a satisfactory bright-annealed product. It was found, however, that the outer layers of wire were discolored and not suited for the use for which they were mtended. To obtain an idea of what was taking place in the annealing furnace, skeins of the hard-drawn wire were placed in a glass tube so that all changes in appearance could be observed as they were heated to different temperatures and under varying conditions. The temperature in each case was determined by means of a thermocouple placed in the tube close to the wire. Following is a summary of the results of these experiments: 1. When the wire was heated for 1 hr. in a current of natural gas at a temperature of 350") 400") or 500" C. (662", 752", or 932" F., respectively), there was a marked darkening of the wire throughout the skein. 2. When heated for 1 hr. in natural gas at a temperature of 600" C. (1112' F.), there was no coloration, the wire remaining clean and bright. 3. When heated in natural gas to 350" C. until darkened and the treatment continued with the temperature raised to 600' C., the coloration disappeared and the wire became clean and bright.

Jan 1, 1923

By W. S. Ayres

The boiler from which these stay-bolts have just been obtained was that of the locomotive Catasauqtia, Lehigh Valley Railroad, built at the company's shops, South Easton, Pa., in 1864. The iron is Lowmoor, and has been in use nearly ten years. The stay-bolts have become highly crystallized from some cause, and are very brittle, only requiring three blows of an ordinary machinist's hammer to break them. On the other hand, when annealed they are remarkably tough, as shown by the doubled sample. The majority of the broken bolts were found to be along the curve of the shell from a to c, Fig. 6. All of them were broken just inside the shell, and in no case next the fire-box. The fractures seem to have been of slow procedure, beginning at the top of the bolt, gradually working deeper and deeper until the pressure of steam overcame the tenacity of the remaining parts. Unequal contraction and expansion of the parts of the boiler seems in this case to be the only existing cause for a fracture. We cannot, from the data obtained, prove to an absolute certainty the manner in which the combined forces generated by the unequal contraction and expansion of the parts have arrived at their resultant work ; but we can, from these data and from existing circumstances, arrive at what seems to be a fair supposition, and thus at least anticipate the truth. The contraction and expansion in locomotive boilers has a large range between its extremes, and is very variable, both with reference to time and to their component parts. The shell and fire-box do not, perhaps, at any time, contract and expand at the same rate, nor proportionally; but, on the contrary, owing to the great changes in temperature that take place both in the atmosphere around the shell, and in the fire in the fire-box, their condition is often changed suddenly, and widely from that which they just previously had. This racking tendency produces strains in the different parts, and it is fair to suppose that the continual motion of the two

By George G. Griswold

The Parkes process of lead refining is based on the fact that when zinc isemixed with molten lead bullion, it forms an alloy with the silver and gold. This alloy freezes at a higher temperature and is of a lower specific gravity than the lead. With proper regulation of the temperature, the alloy solidifies and floats on top of the lead bath, from which it is removed and the silver, gold, and zinc recovered. The alloy should contain the maximum amount of silver (Ag2Zn,). The usual practice is to make two additions of the zinc. The first addition gives an alloy, or zinc crust, the zinc of which is saturated and is treated for the recovery of its zinc and silver; the crust from the second addition contains an excess of zinc and is used for the first addition on the following kettle. The crust produced depends on a number of items: purity of bullion, temperature, care with which kettle work is performed, addition of zinc, pressure used in expelling lead from crust, etc. It is desirable to make the concentration of silver in the zinc crust as high as possible; otherwise an undue amount of byproducts is produced, which greatly increases the cost of refining. It was formerly considered good practice to make a concentration of 20 :1. That is to say, if the lead bullion assayed 150 oz. dorê per ton, the assay of the retort bullion recovered from the zinc crust should be 3000 oz. per ton. As a matter of fact, the concentration should never, except on bullion assaying over 300 oz., be so low, and with low-grade bullion it should be 50:1. In one lead refinery where, ordinarily, the work was good, on a bullion averaging about 200 oz. per ton, a concentration of 24:1 was common; but how it was obtained was known only to the foremen. Changes occurred, and under new foremen the kettle work fell off badly; the problem then was to bring about this greater concentration. As is customary, the refincry had a "schedule" for its 60-ton kettles, which gave the number of pounds of zinc required for all possible assays, on both the first and the second zincing. Using this schedule, high temperatures

Jan 1, 1924

By R. B. Brinsmade

The following is an attempt to form a formula by which a mine can be quickly evaluated, aft,er all pertinent physical data have been collected from observations on the ground by a competent mining engineer. Assumptions. Let Q = price to be paid for the mining property. M = cost of developing the mining property to yield y tons of ore daily. P = cost of suitable plant to treat y tons of ore daily, p = value of said plant when the mine has been exhausted. C = total fixed capital investment. W = working capital investment. Then let C + W = total capital investment. y = required yield of ore daily in tons. Y = yield of ore yearly in tons, d = number of producing days per year, u = average operating profit per ton of ore. R = rate of interest to be earned on total investment of (C + W). r = rate of interest to be earned on sinking fund annuity. v = tons of positive ore available in mine. x = tons of probable ore available in mine, z = tons of possible ore available in mine, m = fractional factor to change probable to positive ore. n = fractional factor to change possible to positive ore. Q = tons of total ore available in mine. t = time in years to exhaust mine at rate Y.

Jan 1, 1909

By James E. Harding

The usual method of sampling mineral deposits is to drill holes and assay the sludge or core. Though the results thus obtained may not represent the true average value of the deposit, it is on these results that estimates of practically all large orebodies are made. In a large number of cases, the results of exploitation fall far short of the estimated value of the orebody. The standard method of making these estimates is to find the cubic contents of triangular prisms, in the apexes of which the drill holes are placed, by. multiplying the surface area by the average depth of the ore in the three drill holes and then multiplying the cubic contents by the specific gravity of the ore or rock to find the tonnage. The assay value is found by dividing the sum of the products of the depth of ore in each hole and the corresponding assay value by the sum of the depths of the ore in the three holes. As the latter part of this method is subject to many mathematical errors, it should not be depended on. Some engineers, therefore, use a discount factor, but as this factor is either arbitrarily selected or is obtained by obscure methods, the results are no better than guesswork. The standard method is correct when the drill holes are so laid out that the triangular prisms are equilateral in cross-section. But as ore deposits cannot always be drilled into at regular intervals and because of the human factor, if many holes are drilled, triangular prisms of all degrees of angularity are produced. In such cases it is necessary to assume that the influence of the different holes is not the same in all directions, which assumption of course is absurd. The area of the triangular prism is usually found by scaling; an ore-body of sufficient size to justify churn drilling is too large to be handled conveniently on maps having a scale larger than from 1000 to 1 to 1,500 to 1 and maps of such scales cannot be accurately measured. A variable is thus introduced in the first operation. In addition, the scaling is frequently done from blueprints, which sometimes shrink as much as 4 per cent. between printing, washing, and drying. The error due to scaling may be eliminated by surveying the location of each hole and

Jan 1, 1922

By Walter A. English, Ralph Arnold

Though production began in Canada only a short time after the discovery of oil in the United States, it has never attained large proportions, and if we were to judge entirely by the past the reserves of Canada would be put at a very low figure. There are only two areas from which oil is marketed at the present time; one, the old district around Petrolia in southern Ontario, and the other is the small Sheep Creek field near Calgary in Alberta. The former district has produced between 200,000 and 800,000 bbl. annually for the past 40 years, recent figures being near the minimum amount. Sheep Creek has produced about 12,000 bbl. annually for the past five years. The known reserves in proved territory in each of these fields are exceedingly small, when considered in terms of world reserves. The chief hope of Canada for reserves of considerable magnitude lies in the western provinces. Sedimentary rocks similar to those in the productive fields of the United States occupy thousands of square miles in the western provinces, so that it seems likely that somewhere within this great area the peculiar conditions necessary for the presence of oil pools will be found. Prospecting is being carried on energetically by several large companies, as well as by many independents. The Dominion Government, which controls most of the public lands, is pursuing a fairly liberal policy toward the prospector, which should stimulate wild-catting, although the province of British Columbia, which controls public lands within t.hat province, is at present unwilling to give adequate encouragement to make wildcatting attractive. As there is really no assurance that any productive pools will be found in western Canada, the estimates of reserves are subject to a wide possibility of error. In making estimates, the various areas within which geologic conditions are more or less uniform are discussed separately; the estimates given for each area are not given with the idea that there is a reasonable probability of their eventually proving to be correct. It is hoped that an average of these estimates, taken together with those made for other undeveloped countries, will give a correct total of reserves

Jan 1, 1923

By Walter A. English, Ralph Arnold

Though production began in Canada only a short time after the discovery of oil in the United States, it has never attained large proportions, and if we were to judge entirely by the past the reserves of Canada would be put at a very low figure. There are only two areas from which oil is marketed at the present time; one, the old district around Petrolia in southern Ontario, and the other is the small Sheep Creek field near Calgary in Alberta. The former district has produced between 200,000 and 800,000 bbl. annually for the past 40 years, recent figures being near the minimum amount. Sheep Creek has produced about 12,000 bbl. annually for the past five years. The known reserves in proved territory in each of these fields are exceedingly small, when considered in terms of world reserves. The chief hope of Canada for reserves of considerable magnitude lies in the western provinces. Sedimentary rocks similar to those in the productive fields of the United States occupy thousands of square miles in the western provinces, so that it seems likely that somewhere within this great area the peculiar conditions necessary for the presence of oil pools will be found. Prospecting is being carried on energetically by several large companies, as well as by many independents. The Dominion Government, which controls most of the public lands, is pursuing a fairly liberal policy toward the prospector, which should stimulate wild-catting, although the province of British Columbia, which controls public lands within t.hat province, is at present unwilling to give adequate encouragement to make wildcatting attractive. As there is really no assurance that any productive pools will be found in western Canada, the estimates of reserves are subject to a wide possibility of error. In making estimates, the various areas within which geologic conditions are more or less uniform are discussed separately; the estimates given for each area are not given with the idea that there is a reasonable probability of their eventually proving to be correct. It is hoped that an average of these estimates, taken together with those made for other undeveloped countries, will give a correct total of reserves

Jan 1, 1923

By H. R. Shidel

This paper summarizes the results obtained from the preliminary cementing of wells in an effort to cut off the bottom water. The object of this work was two-fold: (1) To prevent the oil sand from becoming flooded. (2) To plug off bottom water, thereby preserving the individual well and reclaiming production. Valuable suggestions and help have been given by the following named: Messrs. Kyle and La Velle, of the U. 8. Bureau of Mines; Magnolia Petroleum -Co.; Freed Oil and Gas Co. The cementing work was carried out under the personal supervision of L. J. Snyder. In an unpublished paper on the "Water Problem in the Augusta Field," 5. K. Clark reaches the following conclusions: (1) That the great amount of water present is bottom water, occurring in the Varner sand, the main producing or the 2500-ft. horizon, (2) That the only striking connection between structure and water is in .the area of the marked fault on the Ralston, E. C. Varner, and F. Varner leases in sections 8, 9, 16 and 17. (3) That the oil occurs in porous streaks, generally separated by finegrained, well cemented sand, which is barren. Possibly two or three such pay streaks may be found. That under a pay, fine-grained sand occurs, which is presumably barren at the time of drilling, but soon reveals water. The writer takes partial exception to the last point, because well defined shale, slate, lime, or hard sand breaks have been encountered in a great many cases, separating the pay streaks under which water is often found. This is not an invariable occurrence, as cases have been noted when the oil has been followed immediately by water in the same stratum. In an effort to overcome the water menace, the following methods of plugging were tried: (1) Plugging with wood, lead, and limit plugs. (2) Plugging with sand pumpings.

Jan 1, 1920

By George W. Riter

OUR mineral-land laws need revising so as to provide definite title at the outset to the mineral deposits within any definite piece of land. The laws as they now stand, especially those applicable to lodes, breed uncertainty as to rights of possession prior to patent; and to my mind this is the worst feature of all, worse even than the apex bugbear. It is now almost impossible for anybody to tell-with certainty what mineral rights exist within any area that is not covered by patent, or whether any valid rights exist at all. Our system is unique in permitting individuals to appropriate and exploit mineral lands of the public domain without notice of any kind to the Federal government, and to relinquish them without any ceremony at all. The result is a clouded record that cannot be cleared up until each claimant is put to some sort of final proof. In order to accomplish this, new Federal legislation will be required. The requirements for a mineral survey and the proceedings for patent have always been cumbersome and expensive; and perhaps out of regard for the poor claim owner, who can ill afford the outlay for that sort of thing, the law does not require him to go. through it unless he chooses to do so. Consequently, every active mining district has become encumbered with tangled groups of doubtful or conflicting locations, whose rights and boundaries, when any valuable ore is found, must usually be determined by lawsuits that are as expensive and as distressing as the stakes are high. So deeply has litigation entered into our mining system that a claim whose rights have never been disputed would probably be set down offhand, by $miner of the old school, as of no value. Think of the litigation over rights of possession on the Com-stock lode—12 leading companies involved 'in an aggregate of 245 suits within a period of less than eight years! Ambiguous local records; the chance of erroneously placed or obliterated monuments; doubt as to the sufficient performance of the statutory annual labor; uncertainty as to prior conflicting or overlapping locations; anxiety as to the changing attitude of the Department of the Interior and the Forest Service—such considerations as these make an unpatented mining claim an unclean thing in the eyes of possible investors. Is it any wonder that they keep themselvesand their money at a safe distance,

Jan 1, 1915

By Edward C. Jeffrey

The use of coke in metallurgy, to any important degree, dates from the middle of the 18th century. Its utilization came most opportunely for European civilization. The forests of Europe, except in the most remote and inaccessible regions, had been largely fed, in the form of charcoal, into the smelting furnaces. For a hundred years—the middle of the 17th to the middle of the 18th century—there .was a stationary condition of population corresponding to the exhaustion of European forests. This situation, which was particularly evident in Great Britain, was due to the fact that the forests had been depleted and the practical utilization of coke had not begun. The coking industry is essential for our metallurgical industries, which in turn are basal to healthy economic progress. But coke is of great importance, not only on its own account, but for its byproducts, which enter fundamentally into all the arts of peace and war. The dyestuff industry and the manufacture of explosives are intimately connected with one another, as was shown by the recent war. The subject of coking coal, therefore, is well worthy the serious attention both of practical industry and the scientific investigator. The most valuable coking coals, from the metallurgical standpoint, are derived from the coals of highest ranks. Coals, for example, that have a carbon ratio of from 70 to 80 per cent. yield the most valuable coke for the blast furnace. The difficulty of investigating these coals, however, is great, for they are rather friable and delicate and possess a high carbon content, which makes them difficult to manipulate. They present, on account of their high carbon content, a considerable degree of opacity when examined, in thin sections, under the microscope. The tenderness of structure and blackness of such high-grade coking coals as those of Connellsville and the Pocahontas region make them extremely difficult to investigate. Two of my colleagues, who are taking part in this discussion, will describe the valuable results that have been reached by studying coal by the methods of the mineralogist. Doctor White and Doctor Thiessen have studied the structure of coal as determined from thin sections that

Jan 1, 1925

By John A. Mathews

During the prosecution of the aircraft-production program in 1917 and 1918, the writer visited many plants engaged in the manufacture of motors, planes and parts, in carrying out his duties as chairman of the Committee on Aircraft-engine Forgings. On several occasions, when the question of expansion was discussed, it was noted that there was confusion in the use of the terms: the true coefficient of expansion, a physical constant, and distortion in hardening. One engineer, referring to a steel shown in the accompanying table, stated that he could not consider it for crankshafts because of its excessive coefficient of expansion, while another steel, also Iisted in the table, was said to be especially good because it had no coefficient of expansion, since it came out of the oil bath perfectly straight. Many years ago one of our employees designed a new oil furnace; when asked what became of the products of combustion, he replied: "There ain't any, we burn them all up." While the coefficient of expansion is not without its effect in volume changes in hardened steel, it is not a determining factor in the matter of distortion and going out of shape. Irregular heating, uneven furnace bottoms, and carelessness in withdrawing the part from the furnace, as well as the manner in which the part enters the quenching bath are of greater moment. Generally speaking, also, steels of relatively low hardening temperature will distort less than those requiring higher hardening heats. The coefficient of expansion must be considered in engineering design most frequently when different metals or alloys are used in the same construction. For example, the difference of expansion between a steel crankshaft and an aluminum crank case might be of real importance and a steel with no coefficient of expansion would be much less desirable than one with the normal coefficient. About 15 years ago, the writer made many determinations of the coefficient of expansion at low temperature ranges, usually between 20' and 100" C. Among the materials tested were: Pure forged electrolytic iron, 11.73 parts per million for l° C.; cast aluminum (99.93 per cent. AI.),

Jan 1, 1922

By John A. Mathews

During the prosecution of the aircraft-production program in 1917 and 1918, the writer visited many plants engaged in the manufacture of motors, planes and parts, in carrying out his duties as chairman of the Committee on Aircraft-engine Forgings. On several occasions, when the question of expansion was discussed, it was noted that there was confusion in the use of the terms: the true coefficient of expansion, a physical constant, and distortion in hardening. One engineer, referring to a steel shown in the accompanying table, stated that he could not consider it for crankshafts because of its excessive coefficient of expansion, while another steel, also Iisted in the table, was said to be especially good because it had no coefficient of expansion, since it came out of the oil bath perfectly straight. Many years ago one of our employees designed a new oil furnace; when asked what became of the products of combustion, he replied: "There ain't any, we burn them all up." While the coefficient of expansion is not without its effect in volume changes in hardened steel, it is not a determining factor in the matter of distortion and going out of shape. Irregular heating, uneven furnace bottoms, and carelessness in withdrawing the part from the furnace, as well as the manner in which the part enters the quenching bath are of greater moment. Generally speaking, also, steels of relatively low hardening temperature will distort less than those requiring higher hardening heats. The coefficient of expansion must be considered in engineering design most frequently when different metals or alloys are used in the same construction. For example, the difference of expansion between a steel crankshaft and an aluminum crank case might be of real importance and a steel with no coefficient of expansion would be much less desirable than one with the normal coefficient. About 15 years ago, the writer made many determinations of the coefficient of expansion at low temperature ranges, usually between 20' and 100" C. Among the materials tested were: Pure forged electrolytic iron, 11.73 parts per million for l° C.; cast aluminum (99.93 per cent. AI.),

Jan 1, 1922