Search Documents

By F. A. Penning

An experimental and analytical investigation was conducted on a recoverable pit bottom buffer. Work was conducted at the Colorado School of Mines using the U.S. Bureau of Mine-s free fall test tower. The four-sided butter, one of several designs by Cable Belt Ltd., was constructed of reinforced rubber slabs. The kinetic energy of falling weights, 1670 to 6000 lb, was absorbed by the flexure of rubber slabs loaded along their edge. A series of constant energy, 3000 ft-lb and maximum design velocity, 600 fpm tests were conducted. Static testing of the buffer established the load-deformation behavior. A large hysteresis loop plotted above and below the data published by the manufacturer. Creep was evident during; the loading Lend unloading cycle. Electronic instrumentation measured deceleration using your accelerometers; overall and intermediate movement was found from four displacement transducers; bending strains were recorded at four locations; and base reactions were measured by using four load cells. Data were recorded on tape and played back on a recording oscillograph. High speed movies were taken of all the tests. Symmetry of response and rebounds, when they occurred, were noted. From the displacement-time and load-time data, maximum decelerations were calculated by four methods and different assumptions. Good agreement was found from these approaches. Impact loads ranged from a low of 0.7 to a high of 6.1 gs. A dynamic computer model was written for the response of the buffer. Displacement-time, and acceleration-time plots show close correspondence with experimental data for the ten experiments. Data from accelerometers, displacement transducers, strain gages, and load cells are included. The computer program listing, and displacement-time acceleration-time plots are also presented.

Jan 1, 1980

By A. Galaitsis

This report summarizes part of the work performed under the USBM Contract No H0155113, "Noise Abatement of Continuous Mining Machines." It describes the noise source diagnosis of a Jeffrey 120M conveyor and the evaluation of several treatments all conducted in a test facility aboveground. The conveyor noise at the operator's position was gradually reduced from 101.5 to 93 dBA using damping, vibration isolation, sound barriers and smoother discontinuities. The underground performance of the selected treatments will be addressed in Volume II of the report.

Jan 1, 1979

By Robert S. Schechter

A minitest, consisting of an injection/production well and at least two observation wells designed to detect the arrival of injected fluid leached minerals, and nonideal flow, is considered in this report. The test goals are to determine the susceptibility of the host formation to uranium leaching, kinetic parameters to scale the process, and to facilitate site restoration. This report considers permeability and mineral heterogeneities and other oxidant-competing minerals. To circumvent these nonidealities, which obscure the results, methods of interpretation have been proposed and tested by a computer simulator. In complex cases, clear-cut methods of interpretation were not found; but in every case the design of a test most susceptible to interpretation has been considered. The minitest is operationally simple and can be completed in a short time. With the correct design and interpretation it can return information to evaluate economics, ensure satisfactory leachate performance, scale to larger operations, and to identify restoration problems.

Jan 1, 1983

By Boyd Wise

A jet pump injector was developed and successfully tested, thereby demonstrating the feasibility of a jet injector for introducing coarse coal into an operating slurry face haulage system: In Phase I a variety of injection concepts were evaluated, and the jet pump was identified as best, due to its simplicity, compactness and performance potential. In Phase IIA subscale jet pump injector tests were conducted, and a computer model of a jet pump injector was developed whose performance predictions correlated well with subscale test results. In Phase IIB various system configurations were defined for integrating a jet pump injector into a fully operational underground coarse slurry face haulage system, further highlighting the feasibility and practicality of such a system. In Phase III a full-scale mobile haulage vehicle embodying a jet pump injector and coal sizing equipment was detail designed into a practical vehicle with attractive performance characteristics. More importantly, fully operational full scale jet pump injector -and feeder/breaker subassemblies were tested and proven successful in their ability to down-size coal to 3" in all 3 dimensions and to consistantly provide slurry of 4217 weight concentration at 6.4 TPM throughput under a wide range of operating conditions including zero to maximum feed rate within 5 seconds.

Jan 1, 1985

By M. G. Wallis

This report presents the results of a study to develop a detailed mining method design based on longwall mining with sublevel caving. The method is applicable to low-dipping coal seams 20 or more feet thick such as are found in the western United States. The report covers (1) the development and description of the mining method, (2) evaluation of the engineering feasibility of the design, (3) estimates of productivity and recovery, and (4) an engineering cost analysis and economic feasibility evaluation of the mining method design.

Jan 1, 1977

By M. G. Wallis

This report presents the results of a study to develop a detailed mining method design based on longwall mining with sublevel caving. The method is applicable to low-dipping coal seams 20 or more feet thick such as are found in the western United States. The report covers (1) the development and description of the mining method, (2) evaluation of the engineering feasibility of the design, (3) estimates of productivity and recovery, and (4) an engineering cost analysis and economic feasibility evaluation of the mining method design.

Jan 1, 1977

By D. Randolph Berry

This report describes a study to develop a detailed set of guidelines and equipment recommendations to be used as a guide for mine operators, mine inspectors, and equipment manufacturers in implementing the emergency escapeway standards for metal and nonmetal underground mines. It was sponsored by the United States Bureau of Mines. The first part of this report reviews the historical background of metal and nonmetal mine fires and the development of present and proposed mandatory standards. This is followed by a discussion of the survey of representative mines and how the proposed standard effects these mines. The remainder of the report covers technical discussions of each escapeway component including a comprehensive computer simulation of mine evacuation. Following the technical discussion of each group of escapeway components is a list of the pertinent guidelines. The major escapeway components discussed are the following: Escaperoutes Refuge Chambers Hoisting System. Escapeway Signs Ventilation Fuel Storage Fire Retardants Warning Systems Auxiliary Transportation

Jan 1, 1976

A unity of viewpoint emerged from the workshop. The concept that transmission is via characteristic modes was a common theme in many of the presentations. Also, the confusion an the meaning of monofilar and bifilar to describe these dominant modes was cleared up. But, there was still a healthy divergence of opinion on what constitutes an optimum system. It was generally agreed that further analytical and experimental work is definitely needed. In particular, it was stressed that independent measurements of the constitutive properties of the electromagnetic environment are needed. Also, there was considerable concern that laboratory measurements of rock samples could lead to misleading results for the effective conductivities. Also, there was a general recognition that over simplified propagation theory should not be used to interpret field data. From a theoratical and practical point of view, it was realized that mode coupling plays a vital role in the transmission channel. One must not only understand which and how many propagation modes are excited by the transmitting antenna, but the conversion of energy from one mode type to another must be accounted for. This conversion can either be done intentionally (by fixed mode convertors) or non intentionally (by random wall roughness). In fact, mode conversion can be quite complicated when various propagation paths exist such as when insulated cables, leaky feeders, grounded rails, coal seams, etc. all convey portions of the electromagnetic energy. However, this state of affairs should be regared as an. opportunity for extended communication coverage in mines rather than a limitation of a desig. procedure based on preconceived notions of the dominant propagation mechanism.

Jan 1, 1978

By David Bendersky

The principal objectives of this study are to: (1) survey electrical practices in metal and non-metal mines, (2) survey electrical practices in metal and non-metal mills, (3) clarify the federal regulations governing electrical practices in metal and non-metal mines/mills, (4) analyze electrical accidents, and (5) make recommendations aimed at improvement of the safety of electrical practices in metal and non-metal mines. Information was obtained from literature searches, accident reports, visits to 27 mines and 12 mills, and discussions with knowledgeable industry and government people. The various electrical power systems and practices at the mines and mills visited are described. Similarities and differences based on the type of mining and the minerals being mined or milled are presented. The federal regulations governing metal/non-metal mine/mill electrical practices (Code of Federal Regulations, Title 30, Sections 55.12, 56.12, and 57.12) are presented and discussed. Explanations of each regulation are provided in an appendix. The attitudes of mine/mill operators towards the federal regulations are described. An analysis of the electrical accidents in metal/non-metal mines and mills during the period 1972-1978 is presented. Recommendations, including specific research and development activities, aimed at improvement of electrical safety in metal/non-metal mines are submitted.

Jan 1, 1980

By Mary L. Pearson

Ibis report summarizes the results of the contract. Included are summaries of existing legislation pertaining to outcrop barriers and a state-of-the-art survey of outcrop barrier designs and related, mine closure techniques. Six sites were inspected in the field and are presented as case histories The data analysis presented includes a computer modeled seepage analysis, an overburden blew-out analysis, and a wedge stability analysis. The results tit these analyses are interpreted to form recommendations for coal outcrop barriers which will minimize seepage and the potential for failure. Supplementary support and reinforcement alternatives are also discussed.

Jan 1, 1981

By Michael A. Anuta

This report describes the potential for utilization of satellite observations for remote sensing of mine waste disposal areas. Four study sites consisting of metal and nonmetal mining areas in different climatic and physiographic regions of contigous United States were used in this investigation. The mine waste disposal sites consisted of mining of phosphates in Florida, copper in Arizona, silver in Idaho, and coal in West Virginia. Landsat satellite multispectral scanner observations were used together with aerial photographs, ground surveys, U.S. Geological Survey maps, and other ancillary information. Landsat digital data were categorized using automated supervised classification algorithms and an image analysis system. Detailed description of automated classification techniques employed and the accuracy attained is provided together with the results of manual interpretations. The inventory of areas distrubed for phosphate mining and a change detection investigation for-Polk County Florida were also undertaken during this study.

Jan 1, 1982

By John Wilson

This report describes the performance of Phase I of a project to design, analyze, and demonstrate a multilift longwall mining method applicable to mining coal seams twelve (12) feet or more in thickness. A non-simultaneous multilift operation is the most viable thick seam mining technique for introduction to the United States coal industry. In the case of the proposed site at Emery, Utah it will result in an increase in coal extraction from 30% with present methods to at least 50% and possibly more. The major technological advance involved in this project is mining a lower lift under a previously mined upper lift. To accomplish this, entries must be developed and maintained beneath the upper lift gob. This will necessitate the use of steel supports at frequent intervals throughout the lower lift' entry system. This has not been done in the U.S. to date. An economic analysis of the project indicates that, while this method will result in a higher than average cost per ton for coal mined, the coal would be competitive with current-operation in the area.

Jan 1, 1976

By Gregory B. Beacher

Analyses have been performed on geotechnical properties of copper, uranium and phosphate (gypsum) tailings materials, with the intent of identifying typical measures of variability within and among sites, and of characterizing such variability for use in reliability modeling of tailings embankments. In all, data from approximately 41 sites were analysed. Fairly consistent results were obtained for within site variabilities. However no one probabilistic model was found to be applicable to all sites. The distributional forms for most of the data sets are regular, and tend toward Normality when spatial trends are removed. At many of the sites sufficient in situ data were available to allow estimates of vertical autocorrelation distances and measurement noise. Available data indicate that variability in pore pressures may have a more important effect than strength property variation. A major problem in interpreting available strength property data results from the unknown drainage conditions during testing.

Jan 1, 1983

By R. E. Chaney

This report summarizes the research on the Strategic and Critical Materials Program tasks conducted at the Idaho National Engineering Laboratory (INEL) between May 1984 and April 1985. The work is divided into two areas: 1. Production Technologies - Tasks directed at developing advanced extraction technologies ? Biologically-Assisted Minerals Processing ? Metal/Gas Reactions and Thermal Plasmas ? Dehydration of Aluminum Chloride Hexahydrate (completed). 2. Conservation/Substitution Technologies - Tasks directed toward establishing the technical processing base which will permit the use of advanced materials ? Joining of Rapidly Solidified Alloys (RSA) ? Joining of Silicon Nitride-Based Ceramics ? Nondestructive Evaluation of Ceramic and RSA Joints and Materials ? Substitute Catalytic Materials for Platinum.

Jan 1, 1985

By Terry S. Cory

This report is a comprehensive summary of the results of the propagation measurements program conducted for the US Bureau of Mines under Contract H0366028. Data was gathered in the MF frequency range from a cross sample of six mines representative of the industry having typical wireless requirements. From the raw data which was gathered, a logical method of data reduction is presented which culminates in a set of average attenuation characteristics for all mines visited. These characteristics define a typical MF wireless system when the communication range requirements are known. Direct through-the-earth propagation and the range enhancement mechanism due to coupling on and off conductors are evaluated and related to the planning of a typical wireless MF communications system.

Jan 1, 1977

By William R. Archibald

This report presents the results of a program demonstrating the technical and economic feasibility of hydraulic borehole mining of uraniferous sandstone. This mining technique involves the drilling of a borehole from the surface down into the ore body. A borehole mining tool consisting of a high-pressure cutting jet and a slurry jet pump is lowered down the borehole. Water from the high-pressure cutting jet cuts into the sandstone formation generating a water-sand slurry which flows to the slurry jet pump and is pumped to the surface. The cutting jet is rotated and moved up and down from the surface, thereby generating a cavity in the formation. When the cavity size reaches a point beyond the effective radius of the cutting jet, the mining tool is moved to an adjacent borehole and the process is started again. This program was carried out in four phases. Phase I included modifications to the borehole mining system (built and tested under a previous contract, No. H0252007, for the mining of coal) and factory tests of the jetting system. Phase II covered the field tests and a public demonstration. Phase III involved nozzle and equipment modifications and factory tests. Field testing continued under Phase IV along with an evaluation of this method. The field tests were conducted successfully on Rocky Mountain Energy Company's Nine Mile Lake property near Casper, Wyoming. Results indicate that; hydraulic borehole mining of uranium is technically feasible (300 tons of uraniferous sandstone were mined from a depth of 90 ft) and the hydraulic borehole method is economically attractive. However, additional testing is required to clearly define the economic feasibility.

Jan 1, 1978

By Terry L. Muldoon

This report describes development and demonstration of an upgraded stench fire warning system for underground wines. Current systems, which have been used since before 1920, release an ethyl mercaptan mixture into the mines' compressed and/or ventilation air during emergencies. Miners, when smelling ethyl mercaptan, evacuate the mine according to predetermined plans. These systems, while simple, have problems with safety and reliability. The upgraded system overcomes these problems. The system uses a different stench agent, is less toxic, less nauseating, and less corrosive than ethyl mercaptan. These combined with the feature of thiophane not reacting with iron oxides, makes the upgraded system safer and more reliable. The system also uses a combination of two simple principles: a standpipe with pressure balancing to provide a constant head, and a sized orifice to control the rate of release of the stench agent. This system enables the mine to release the agent for a longer period which provides better coverage and to ensure that miners will not be exposed to potentially toxic concentrations of the stench agent. The system is easy to operate, requiring only the turning of two 1/4-turn ball valves. The upgraded system has been successfully tested during two evacuation drills at an underground uranium mine. Using three injectors (one on the compressed air line and one on each of two intake air shafts), the system exhibited significant improvements in warning times over the mine's existing system. This report provides a detailed description of the system design and its demonstrated performance in two mine demonstrations.

Jan 1, 1981

By E. D. Palmes

Phase I of these studies demonstrated the feasibility of measuring the efficiency and capacity of sorbents in tube-type samplers for contaminant gases. This was accomplished by measuring concentration at various points along the length of the diffusion path during sampling. Concentrations were measured by removing small aliquots with gas-tight syringes and gas chromatography. With hexane as the gas and activated charcoal as the sorbent the procedure was quite successful and we proceeded with Phase II of the study; this involved application of the principle to gases of importance in diesel exhaust using a variety of sorbents. When we worked with high concentrations of the test gas we clearly demonstrated the differences in both efficiency and capacity of the sorbents for each of several gases. The chief drawbacks of the system were that we were unsuccessful in determining more toxic gases at realistic occupational exposure levels or determining formaldehyde at any level using the flame ionization detector. It was concluded that, although the method is feasible, more sensitive methods of measuring concentrations of gas in the tube must be developed to make the procedure applicable to regions of chief industrial hygiene interest.

Jan 1, 1983

By Ben Aleck

The objective of this program was to adapt Space Shuttle technology on high-performance spherical pressure vessels to cylindrical pressure vessels. Specifically, a cylindrical aluminum liner overwrapped with fiberglass filaments and prestressed by yielding the liner under a sizing pressure was to be replaced by a higher strength-to-weight ratio steel liner overwrapped with a higher strength-to-weight ratio filament. The steel was cryoworked stainless steel and the new fiber was Kevlar 49. In addition, the heavyweight ends of the aluminum liner were to be replaced by thin-walled domes which required multiple helix angle wraps for their support, in place of the single kite-string wrap from pole to pole of the aluminum overwrapped design. The use of cold swaging of tube-ends to form bosses, demonstrated on subscale development efforts, had not been achieved full-scale when the contract was initiated. Difficulties arose with the full-scale demonstration which were not solvable at the time with the designs and equipment available. hence, an unanticipated development was the finally selected method of making the 4-in.-diameter stainless steel liner with a single boss and no welds in an 0.020-in.-thick wall, from an 0.050-in.-thick, 13-in.-diameter disk. The demonstration vessel failed by leakage during the prestressing step because embedded oxides had formed flaws in the boss region. Such flaws have been avoided by proper temperature control during hot spinning. Hence, a new design was developed which weighs half as much as its recently developed predecessor. Funds ran out before adequate testable hardware was produced.

Jan 1, 1983

By John D. Foulkes

An investigation is made into whether commercially available equipment can be used to engineer effective emergency warning systems for underground coal mines. Discussions with members of the Bureau and the Mining Enforcement and Safety Administration established that the preferred system should operate over the existing Pager Phone twisted pair, and broadcast an audio alarm. Applicable equipments such as voice band tone signaling equipment, alarm sounding equipment, mine telephones and complete alarm systems from over thirty manufacturers are listed. Factors affecting the range over which an alarm could be detected in representative mine situations were studied. These included (a) the subjective masking effects of typical background noise found in mines, such as that due to continuous miners (b) the attenuation of sound in mines (using both a theoretical and experimental results) and (c) the attention-getting qualities of different sound for miners. Audio alarm systems meeting the requirements can be installed and representative systems are described.

Jan 1, 1977