Search Documents

By Shun Myung Shin, Kang Jeong, Kyoungkeun Yoo, Jin Koo, Dong Hyo Yang, Soo Sohn

"The optimum discharging condition to dismantle the batteries without explosion was investigated to recycle the lithium primary batteries, which could be exploded by heating too much or crushing. The 3 waste lithium primary battery cells were discharged with 500 cm3 of 0.5 kmol·m-3 sulfuric acid. Fe concentration and pH increased rapidly after 3 days at 35? and after 1 day at 50?. Chromium concentration increased by 4 days at 35? and 2 day at 50?and then decreased, and nickel concentration was very low. Because Li concentration increased gradually, Li became dissolved after the dissolution of cover material. When the discharged batteries were shredded, the batteries discharged at 50°C were not exploded and those discharged during 3 days at 35°C were exploded. This result shows that the waste batteries could be stabilized within 1 day at 50°C and 4 days at 35°C. Introduction Lithium has some advantages for battery e.g. it is the lightest metals and also has the highest electrochemical potential at 3.04V[1]. For over thirty years lithium primary batteries became famous for their performance in various applications such as IT, medical, and military[2,3]. They gained a reputation for their long shelf life, constant voltage, wide operating temperature range, and low self-discharge characteristics[3-5]. World primary lithium battery market was expected to grow from $820.6 million in 2003 to $1,1355.3 million in 2010 (http://www.frost.com, Frost & Sullivan)[2-4]. The lithium primary batteries have very various sizes and components. Lithium batteries are made with lithium metal as anode active material and non-aqueous solvent as electrolyte. As cathode active material, various kinds of materials were used such as manganese dioxide (nominal voltage, 3.5V), thionyl chloride (3.6V), and carbon monofluoride (3.0V). In Korea, 50 % of the spent lithium primary batteries must be recycled because spent lithium primary batteries have been listed in EPR (Extended Producer Responsibility) of the enforcement degree of the act on the promotion of saving and recycling of resources. However, the batteries have been landfilled since there is no economic method to recycle the batteries in Korea[2,3]. When the batteries were heated too much, charged, pierced, over discharged, or short-circuited, the batteries explode because lithium reacts violently with water or air and because contents such as lithium, electrolyte, and sulfur become flammable by high temperature[4]. Therefore, it is so difficult to recycle safely the spent lithium primary batteries."

Jan 1, 2008

By M. T. Abasov

Among a host of challenges dictated by the explosively developing scientific and technical revolution, the improvement of control and management is one of the most essential problems. This problem is also of far-reaching importance for the oil and gas industries. An oil and gas extracting complex is an involved multilink system characterized by a great number of elements and by intricate interconnections between these elements. Of paramount importance for these systems is the quality of control. Any deviation of the control from the optimum reduces the effectiveness of the system and deteriorates its basic technical and economic factors. In case of large systems, even a relatively small deviation from the optimum may result in considerable material and power losses. Optimization of control of large production systems is therefore one of the basic means to enhance their effectiveness. The present paper discusses a development control problem for a multilayer gas deposit using the method of simultaneous exploitation of several strata by means of a single well. The optimum control is achieved by determining the dynamics of changes in the number of producing wells in a reservoir with regard to the depth of occurrence of these reservoirs as well as the difference in the time of introduction of the wells from drilling and their transfer to another reservoir. A mathematical model was constructed for the problem under consideration and a method was given to solve this problem. The problem was dealt with under the assumption that either each of the reservoirs or a part of them have vertically overlying areas and that there is no hydrodynamic interference between the horizons. It was

Jan 1, 1977

By D. A. Phillips

A procedure for designing an optimum pit to yield maximum profit is described. The volume in which a possible pit is considered is divided into discrete blocks, each of which is assigned an economic value equivalent to its worth as a block of mineable material. The profitability of a pit can then be generated by summing the blocks within the pit. The optimizing procedure starts at the surface level and proceeds downwards level by level, to obtain the optimum pit at each level. The method makes use of the fact that an optimum pit at a particular level must be completely contained in any optimum pit at a lower level. Procedures for generating block costs, and pits with various slope angles under the restriction of complete block removal are considered briefly. The main description is of the theory of the method and the computer program based on this. The method is applicable to any type of mineral deposit, the only requirement being that the orebody should be represented accurately by a block model.

Jan 1, 2014

By S. J. Jung

The stability of underground openings for deep mines is critical, since incorrect orientation or geometry of shaft, stope, and accessways often results in the failure of openings due to high stress concentrations. Current state-of-the-art procedures for the design of underground openings are largely based on rules of thumb, experience, and trial and error. Rules of thumb are invariably based on the past experience of the designer and may not remain optimal as the depth and complexity of mine workings increase. Often, as conditions change, and as the interaction between geology, in-situ stress conditions, and mine openings grows more complex, the cost of maintaining structural integrity becomes prohibitive. Existing design procedures for deep mines are rapidly becoming inadequate as mines are worked at greater depths. For example, in the Coeur d' Alene Mining District, several million dollars are spent for inspection, repair, and maintenance on a regular schedule, largely as a result of inadequate design. In these types of situations, it is of critical importance that a new design methodology be developed for the layout and design of underground openings.

Jan 1, 1994

By Helmut Lerchs

An open-pit mining operation can be viewed as a process by which the open surface of a mine is continuously deformed. The planning of a mining program involves the design of the final shape of this open surface. The approach developed in this paper is based on the following assumptions: 1. the type of material its mine value and its extraction cost is given for each point; 2. restrictions on the geometry of the pit are specified (surface boundaries and maximum allowable wall slopes); 3. The objective is to maximize total profit-total mine value of material extracted minus total extraction cost. Two numeric methods are proposed: A simple dynamic programming algorithm for the two-dimensional pit (or a single vertical section of a mine), and. a more elaborate graph algorithm for the general three-dimensional pit. ASURFACE mining program is a complex operation that may extend over many years, and Involve huge capital expenditures and risk. Before undertaking such an operation, it must be known what ore there is to be mined

Jan 1, 1965

Depending on material commodity market conditions, material contained in open pit waste disposals can hold potential value, Segregating subgrade material into separate disposals i.e. 'sub ore' stockpiles, affords open pit operators the opportunity to modify production strategies to reflect changes in market conditions. Discussion of the concept of subore stockpiling is presented. A two-step mathematical model and a nonlinear programme are employed to answer questions such as, 'how can the value of sub-ore material be determined to distinguish sub-ore from true waste?' and 'when and at what rate should sub-ore be processed?'

Jan 1, 1988

The traditional concept of optimum drill and blast is that it is achieved when ore is produced at the lowest unit cost and, because of the complexities of most mining operations, represents a band which extends either side of an overall cost m

Jan 1, 1998

By Peter G. Bellairs

The traditional concept of Optimum Drill and Blast is that it is achieved when ore is produced at the lowest unit cost and due to the complexities of most mining operations represents a band which extends either side of an overall cost minima. The above definition implies that Optimum Drill and Blast is static and once blasting is within the band around the cost minima then the process is optimised. However mining operations are not static with many events both long and short term impinging on the cost structure and productivity.

Jan 1, 1995

In some 35 years in the explosive and construction industries, we have probably seen the extremes in drilling and blasting practices. All of you know that it is difficult if not impossible, to separate those two operations, particularly when we are searching for an optimum. Early in my career while doing engineering survey work for a major cross country pipeline construction company, we witnessed some of the wildest blasts imaginable, and they were wild for two reasons. Both the drill hole diameter and the drill pattern were such that when loaded with explosives, the factor in terms of pounds/cu. yd. was extremely high. On the other hand, in 1982 we were in an underground coal mine where just one hole was used to prepare a 20-ft. (6m) wide face. In this coal mine, they brought down 7 yd3 (5.35m3) of coal with just 1 lb. (.454 kg) of explosive. On a pipeline job, the factor may only be .1 yd3 per lb. of explosives. Open pit operations in the same geographical area may have almost the same type of rock, but similarities could end there. The several operators over the years will have installed different size-crushing equipment or variances will exist in other facets such as drilling, excavating, and haulage units. That tells us that if we have 6 operations in that common area, we are faced with a fact that there is an optimum drilling and blasting pattern for each of those six. We start at that point. We will note from Figure No. 2 the simple equations for determining either cu. yds. or tons. For a rock heavier than limestone, it may require only 10 to 11 cu. ft. (.31m3) for 1 ton (.91 metric ton) of rock in place.

Jan 1, 1986

By Saad Elias Kaskah

"The Box-Behnken Design (BBD) is used to model the sacrificial Cathodic Protection System (SCPS) to find the factors effectiveness behaviour. For protection potential assessment the BBD receives (resistivity of environment, sacrificial anode alloy, distance between anode and cathode and surface area for the structure to be protected) as input and gives the protection potential as output. By applying BBD with their analysis tools we get many results. The important results which are the factors individual effectiveness on the sacrificial cathodic protection (SCP) process are the resistivity which has the greatest effect on the potential protection (rank=l) followed by sacrificial anode alloy type (rank=2), surface area for structure protected required (rank=3) and distance between anode and cathode (rank=4). The interaction of sacrificial anode alloy and cathode area {X2X4 ) has significant effect on CP process with the limits which are used in this work while the other factors interaction (X1X2, X1X3, X1X4,X2X3, X3X4 ) has insignificant effect on the limits which used in this work.IntroductionFor carbon steel in seawater the normal corrosion potential E '°""_is in the range -550 to -600 mV vs. Ag/AgCI [1]. The most effective method to overcome the corrosion is cathodic protection {CP) which represents a control method in the steel wall corrosion. Cathodic protection has been used in several areas including marine and underground structures, storage tanks, and pipelines [2]. Sacrificial anodes system generates protective current which depends upon the inherent potential difference between the anodes and the structure to be protected. If the structure is made of iron or steel, any metal that is more active in the electromotive force series can theoretically be used as anode material [3]. There are many factors influencing on cathodic protection like resistivity (NaCl content), chemical composition of sacrificial anode alloy, distance between anode and cathode, surface area of cathode, temperature, humidity, velocity of solution, dust, impurities, bacteria and etc .. The present work studied four factors: NaCl content, resistivity), chemical composition of sacrificial anode alloy, distance between anode and cathode, surface area of cathode) with different three levels of values for each one. Then this work will find the optimum value from the factors levels that tacked to investigated there influencing on sacrificial cathodic protection system."

Jan 1, 2013

By A Fyans, B Ghahreman-Nejad

This paper discusses the method and results of an options study into selection of the optimal form for a 130 m high tailings/water retaining dam, located in a region of high seismicity in central Iran. The proposed dam is part of a planned expansion project for Sarcheshmeh Copper Mine (SCM), which after construction will provide 550 million tonnes of additional tailings storage over the next 27 years. Geotechnical investigation at the proposed site indicated that adequate suitable low permeability materials (i.e. clay) were not available in the immediate vicinity of the dam site and would need to be imported from a distance of well over 10 km (direct). Given the magnitude of the estimated quantity of material and construction cost it was considered prudent to compare the cost of alternative dam design options for the proposed storage. A total of five dam design options are considered including a conventional rockfill embankment dam with an upstream sloping earth core (ECRD), a geomembrane face rockfill embankment dam (GFRD), a sloping asphalt core rockfill embankment dam (ACRD), a roller compacted concrete dam (RCCD), and a filter rockfill embankment dam for tailings storage together with a separate smaller earthfill core rockfill dam (ECRD) located downstream for storage of decant water. The risks, costing and design of all options are discussed in detail and the outcome of the study is presented.CITATION:Ghahreman-Nejad, B and Fyans, A, 2018. Optimum embankment design for a tailings dam, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 427–438 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By Jessica Barber

Problem ? Mining operations consistently need equipment that is available, and able to perform to its maximum potential ? The most difficult part of a Maintenance Manager?s job is often a lack of knowledge on how long their equipment has to last ? The short term view can lead to interim fixes that accumulate into larger problems ? It is always difficult to justify major overhauls and upgrades when there is pressure to meet mine plan production targets

May 1, 2008

By Kai Nielsen

In underground mining coarse muck and large boulders lead to ineffective utilization of costly mining equipment, and extra expenses and delays caused by secondary blasting. Cost analysis in some Norwegian mines shows that these extra expenses may amount to 10% or more of total mine operating costs. A computer model has been developed for sensitivity analysis of underground longhole stope blasting. The basic idea of the model is : When increasing the blasting energy input and fragmentation costs, the fragmentation will be better. This will lead to cost savings for loading, hauling, secondary blasting and primary crushing. The blasting design giving the lowest overall costs will indicate the optimal practice. The model has been used with data from several underground operations in Norway. An example run with typical costs shows that the costs for drilling, blasting and secondary blasting are the most significant parameters in the optimization process.

Jan 1, 1986

By S Casas Castellanos

"Tyres consumption is one of the costliest branches of the operation in a truck-based haulage mine. Off-the-road (OTR) tyres working within undesirable conditions have a considerable negative impact on the whole mine’s productivity. Only the rolling resistance due to underinflated tyres could increase truck fuel consumption by 15 per cent. The impact of other conditions such as road surface quality and temperature are difficult to estimate. Tyre management is a demanding activity that requires a high level of coordination between maintenance and production departments.The project is aimed to develop a smart decision tool to assist mine managers to optimise tyre resources. By identifying factors that have significant impact on tyres, managers are able to take timely action to mitigate undesirable working conditions.The proposed model utilises real-time tyre measurement of pressure, temperature, speed, load, deformation and surface profile to report tyre performance in terms of tonne-kilometre-per-hour (TKPH) and tyre longevity. Both indicators are permanently monitored in order to trigger a warning system designed to keep tyres under optimal working conditions.An interactive database ‘Octo-Mine’ wirelessly receives records from a programmable logic controller (PLC) deployed on the truck. PLC records are the integration of multiple sensor signals with a time stamp. Octo-Mine utilises real-time and historical tyre records to generate online performance and longevity reports, as well as preventative and corrective tyre maintenance scheduling, by comparing current tyre status with established standards.To validate the model, the prototype database was populated with hypothetical data to simulate ideal working conditions subject to comparison with real field observations. Additionally, a laser-based technology prototype device successfully measured a new 9 mm tyre tread and a 60 000 km rolled tyre tread in the laboratory.In conclusion, optimal tyre management contributes not only to reduction of tyre waste but also to truck energy efficiency. This project is a first step in proving these benefits under real field conditions. It suggests that further development of sensor equipment and its integration with a communication system is a worthwhile focus for future research.Citation:Casas Castellanos, S, 2016. Optimum Management of Truck Tyres in a Mine, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 212–228 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

By T. Johnson, D. Kelley, J. Graham

"Hydrometallurgical processes can be exceptionally corrosive. Conditions associated with metal extraction and refining require materials of construction that can withstand process acids and acid chlorides at temperatures up to 90°C (194°F). Process vessels, piping, scrubbers and ducting can be rapidly compromised in these aggressive environments if not designed with care. Design engineers are challenged to find materials that can stand up to hydrometallurgical processes especially for copper, zinc, nickel, cobalt and uranium. This paper will evaluate material solutions to determine which provides attractive economics for initial procurement as well as high durability for reasonable life cycle costs.INTRODUCTIONMining activity in a number of metal ores has been running quite high over the last few years. In particular, those metals that employ acid functional extraction processes such as copper, nickel cobalt and uranium have been particularly active.The world’s largest nickel mine – the massive $4.76 billion Ambatovy nickel mine on the African island nation of Madagascar is nearing completion. When it reaches its full production capacity in 2013, the mine will produce 60,000 MT/yr of nickel and 5600 MT/yr of cobalt. Coming on the heels of the Ambatovy project is the Long Harbour Processing Plant in Newfoundland, Canada which will process the ore from Vale’s Voisey Bay mine in Labrador. Voisey’s Bay is expected to generate more than 50,000 MT/yr of nickel ore when it starts up in 2013. Next up will be the Boleo project in Mexico on the Baja peninsula. When commissioned in 2013, the $858 Million Boleo project is expected to produce 60,000 MT/yr copper, 3100 MT/yr cobalt, 36,000 MT/yr zinc and 100,000 – 250,000 MT/yr manganese carbonate.High nickel alloys and rubber lined steel have been used for decades to design corrosion resistant equipment for mineral processing environments. These materials demonstrate reasonable resistance to corrosion for most environments. Unfortunately, higher nickel alloys are quite expensive. Rubber lined steel is a bit more affordable but requires continuing service over time which ultimately drives up its cost as well. FRP (Fiberglass Reinforced Plastic) has also been used extensively in mineral processing for tanks, piping and ducting employed in aggressive environments. Today, more and more design engineers and material specifiers are calling for FRP composites for both new and replacement equipment used in the refining and processing of a variety of metal ores."

Jan 1, 2012

By Matthew J. DeMarco, Anthony T. Iannacchione

Coal bumps have presented serious mining problems in the U.S. throughout the 20th Century. Fatalities and injuries have resulted when these destructive events occur at the working face. Persistent bump problems can result in abandonment of large reserves or lead to premature mine closure. Through the years, a1ternative techniques such as artificial supports, extraction sequencing, destressing, pillar design changes and specific pi1lar retreat practices have been successful1y imp1emented to mitigate coal mine bumps. Several techniques have evolved for room-and-pi1lar operations that control the way the roof rock breaks, regulating the manner in which stresses are redistributed in the mined section. Special mine layouts employed in longwall mines have also proved to be successful in safely redistributing or containing excessive loadings. However, with ever increasing production rates, greater overburdens and new mining systems, the need to evolve even more effective bump control designs will continue to challenge the U.S. coal mine industry.

Jan 1, 1992

By Matthew J. DeMarco, Anthony T. Iannacchione

Coal bumps have presented serious mining problems in the U.S. throughout the 20th Century. Fatalities and injuries have resulted when these destructive events occur at the working face. Persistent bump problems can result in abandonment of large reserves or lead to premature mine closure. Through the years, alternative techniques such as artificial supports, extraction sequencing, destressing, pillar design changes and specific pillar retreat practices have been successfully implemented to mitigate coal mine bumps. Several techniques have evolved for room-and-pillar operations that control the way the roof rock breaks, regulating the manner in which stresses are redistributed in the mined section. Special mine layouts employed in longwall mines have also proved to be successful in safely redistributing or containing excessive loadings. However, with ever increasing production rates, greater overburdens and new mining systems, the need to evolve even more effective bump control designs will continue to challenge the U. S. coal mine industry.

By Y. C. Kim

For the past quarter of century, much more effort and research have been expended in developing the "optimum" ultimate pit limit design algorithms and much less to solving the "optimum" open pit production sequencing. However, the potential economic benefit to an operating mine is far greater for the latter than the former. Unfortunately, the problem of "optimum" open-pit production sequencing has not been fully solved to date. This paper first reviews the past and currently used methodologies for developing this sequence. The staggered pit phase geometry problem of advanced stripping and operational constraints such as ore and waste tonnage requirements by period and necessary contiguity of mining faces are the main reasons why the "optimum" production sequencing problem has not been solved as yet. This paper also explains why any method which attempts to simplify the problem using ultimate pit limit design algorithm will fail to reach an "optimum" solution.

Jan 1, 1994

By Thys B. Johnson

Traditional mine planning concepts are discussed and suggestions for improvement through use of the developed model are proposed. The approach developed in this paper allows optimal planning of the complete mining-concentrating-refining system over the entire planning horizon and permits the system to dictate how and when to process a block of material, i. e., a dynamic cutoff.

Jan 1, 1969

By Sebastian Avalos, Julian M. Ortiz

The long-term mine scheduling is the optimal decision on how to extract and process the mining reserves. The resulting plan is mainly driven by economic, metallurgical, and geological factors. Accounting for their uncertainties leads to a robust solution and the feasibility for economic-risk quantification. In this work, we model the spatial uncertainty of grade distributions of multiple correlated elements, by using a multivariate morphing transformation. The result is a set of multivariate geostatistical realizations of the grades, which honor the conditioning data, the direct and cross variograms, and the multivariate statistical distribution, inferred from a set of samples. These models are the input in a reinforcement learning framework, adopted to train a deep neural network that considers the grade uncertainty and leads to an optimum mine plan after training using deep Q-Learning. Mining and processing capacities, as well as economic parameters and metallurgical constraints, are incorporated as the reinforcement learning environment rules. The method is validated on a real deposit, providing insights for future applications.

Jun 25, 2023