Search Documents

By David C. Lynch

FeCl3 particulate of 10 to 100 um in diameter was reacted with radicals produced in an oxygen plasma at pressures between 1 to 20 Torr. The particulate, in a fluidized bed, was positioned above the plasma to avoid over heating the oxide product which is known to lead to crust and clinker formation[ 1 ]. Reaction between the iron chloride and the gas phase occurred at temperatures between 66 and 226 °C. Oxygen radicals react with the surface material to a depth of approximately 2.5 4m. Surface material, analyzed with a x-ray technique, indicates that the maximum amount of FeCl3 reacted on a weight basis was found to be approximately 67%. More typically, 40 to 50 wt% of the chloride was reacted within 30 minutes to 1 hour.

Jan 1, 1996

By J. Jara

Oxygen, ozone and air were evaluated in the oxidation of ferrous iron in the presence of hydrochloric acid ranging from 0.1 to 4 M HC1. Stoichiometric coefficients were determined through mass balances of gases and ferrous titration. The molar ratio ferrous to ozone increases from two at 0.1 M HC1 concentration to six at 4 M HC1. For oxygen the same ratio is constant and equal to 2 and it is in agreement with other works. The stoichiometric coefficient of hydrogen ion was not defined due to the effect of hydrolysis of ferrous and in particular ferric ion on measuring acid concentration by titration with sodium hydroxide. Agitation, gas flow and pressure contribute in the utilization of gas. A technique to compare the gas efficiency at several conditions is discussed and it is based on the relationship between oxygen and ferric during time. There is a strong compromise between gas efficiency and ferrous conversion. Oxygen efficiency decreased with time due to ferrous depletion. The gas efficiency ranged from 3 % (low level of agitation) producing 25 g Fe(III)/h to 12 % at 1000 rpm with 60 g Fe(III)/h converted. At 405 kPa absolute the oxygen efficiency was in the range of 80 % producing 300 g Fe(III)/h. The replacement of chlorine with oxygen to enrich molybdenite concentrates by reducing copper to less than 0.2 % was evaluated. Oxygen can be employed in batch or continuous operation and it can treat molybdenite concentrates with high variation of copper content. The dissolution rate is mainly controlled by oxygen addition in which utilization of oxygen plays an important role. Improvement on safety and environmental conditions is feasible by using oxygen instead of chlorine gas. The economics indicate good opportunities to implement oxygen without significant modifications to the actual circuit and enough benefit when oxygen is well used.

Jan 1, 2007

By Hong Yong Sohn, Miguel Olivas-Martinez, Zhixue Yuan

A novel flash ironmaking process that directly reduces iron oxide concentrate particles by gas is under development. The goal of this work was to study the possibility of reoxidation of iron particles in various gas mixtures. As the product iron cools down in the lower part of the flash reactor, conditions may become favorable for reoxidation because of equilibrium and high reactivity of iron particles. The effects of temperature (823 – 973 K) and H2O partial pressure (40 – 100 pct., Ptotal = 86.1 kPa) on the reoxidation rate were examined. The pressure dependence was first order with respect to water vapor, and the activation energy was 146 kJ/mol. A complete rate equation that adequately represents the experimental data was developed. For oxidation in O2-N2 mixtures, the effects of temperature (673 – 873 K) and O2 partial pressure (5 – 21 pct., Ptotal = 86.1 kPa) were determined. Reoxidation in pure CO2 was also investigated at 873 – 1073 K for comparison.

Jan 1, 2014

By Satu Strömberg

A single-particle laminar-flow technique was used to study oxidation of two nickel concentrates and a granulated nickel matte (43 wt% of Ni). Experimental conditions were: reaction gas from N2 to N2 + 75 vol% O2; gas preheating temperatures ranging from 500 to 1100°C. The major nickel-bearing minerals in the two concentrates were pentlandite and violarite, respectively. Chemical analysis of the particles was used to determine the oxidation degree of the materials, and optical and scanning electron microscopy were used to detect their morphology and mineralogy. Total desulfurization of the nickel concentrates was achieved under the most oxidizing conditions, while the sulfur removal from the nickel matte was not as efficient, especially with the coarse size fraction. Pentlandite-based concentrate was found to be less reactive than the violarite-based.

Jan 1, 1995

By Hongqiang Wang, Qingliang Wang, Eming Hu, Zhiwu Lei, Fang Hu, Rui Zhang, Wei Hou

Pyrite, a mineral associated with uranium ore, is closely related to uranium leaching. In this study, Ozone micro-nano bubbles (OMNBs), as an environmentally friendly advanced oxidation technology, were used for the first time to oxidize pyrite under experimental conditions to improve the leaching rate of uranium. A laboratory-scale agitation leaching experiment of pyrite was carried out with a pH of 1.0–3.0, gas flow of 1–3 L/min, ozone generation rate of 0.55–2.22 mg/s, and pyrite concentration of 0.1–5.0 g/L for 1 h. By adding three different co-oxidant: Mn(II), Mn(IV), and Fe(III), it was found that only Mn(IV) increased the oxidation rate of pyrite by 21.7%. The results of the scanning electron microscope (SEM) and X-ray photoelectron spectroscopy (XPS) show that the formation of Fe(III)-O film on the surface of the ore suppresses the oxidation rate of pyrite to a certain extent. Pyrite can be rapidly oxidized up to 57.6% by OMNBs, which is beneficial to uranium leaching. This method is expected to be used for in situ acid leaching of uranium with OMNBs injected into the ground.

Jan 3, 2022

By Satu Jyrkönen

A single-particle laminar-flow technique was used to study oxidation of four synthetic nickel mattes, which were screened into three size fractions, Experimental conditions were: reaction gas from N2 - 21 to 75 vol-% O2; gas preheating temperatures ranging from 500 to I 100'C. The four mattes were synthesized so that Ni/Cu ratios of I and 10 were obtained with high and low iron contents. Chemical analysis of the particles was used to determine the oxidation degree of the materials, and optical and scanning electron microscopy were used to detect their morphology, internal composition and structure. The best sulfur removal from the synthetic nickel mattes was achieved under the most oxidizing conditions with the finest size fraction. The matte with Ni/Cu = 1 and high iron content was found to be most reactive. The least reactive matte was with Ni/Cu = 10 and low iron content; the coarse fraction particles did not react at all under the conditions studied.

Jan 1, 1996

The merging of flash smelting with spray converting in one single furnace is proposed as a continuous copper making process. The proposed process is expected to produce blister copper, clean slag and gas with high sulfur dioxide concentration. Some high grade matte is an intermediate product recycled within the proposed furnace, spray-atomized and converted. The thermodynamic equilibria of the simultaneous oxidations which take place during copper smelting and converting are discussed in order to establish the gradient of oxygen potential along the furnace required for smooth operation. The proposed process is a dynamic system designed to reach equilibrium only close to the slag skimming end of the furnace. The process feasibility is based on the predesigned significant difference between the rates of converting reactions in a finely dispersed system and the rates of deconverting reactions between immiscible liquid phases of restricted interface area. The converting of small stationary droplets of matte, in a silica saturated system, was studied in the laboratory for extremely short oxidation times (10 to 120 seconds). These experiments led to some interesting observations on reaction mechanisms and kinetic trends. The droplet size and the matte grade affected very strongly the oxidation rate and the proportion of the different products obtained.

Jan 1, 1976

By J. E. Nesset, J. A. Finch, Rosenblum. F., S. Somot

"In a previous presentation at the CMP, evidence was shown for the formation of hydrogen sulphide (H2S) in self-heating experiments on pyrrhotite-rich samples (Somot and Finch, 2006). Oxidation of H2S is strongly exothermic leading to the proposition that H2S is playing a key role in the self-heating process. Subsequently, tests in two weathering apparatus (I and II) were run under varying oxygen levels to further examine conditions leading to self-heating. To characterise their resulting self-heating capacity the samples from the weathering tests were subjected to a modified Stage B test using the self-heating apparatus developed by Rosenblum and co-workers (Rosenblum and Spira, 1995; Rosenblum et al., 2001). Results showed highest self-heating after weathering occurs under low oxygen conditions, supporting the H2S hypothesis. It was observed that highest heating rates are not directly related to highest weight gains of samples.INTRODUCTION“Sulphides” refer to several types of minerals containing sulphur in its lowest oxidation state of - 2. Self-heating is the spontaneous heating of a material without external heat input. It is well established that some sulphides will self-heat on exposure to moisture and oxygen (Farnsworth, 1977; Good, 1977; Rosenblum et al., 2001; Wu and Li, 2005). This process is highly exothermic and if the heat generated is not dissipated, combustion may occur when the temperature reaches the ignition point of the sulphide (typically 350-400 °C). The hazards of sulphide self-heating range from handling hot material, to sulphur dioxide release, to fires. The literature documents self-heating incidents underground, on ships and trucks transporting sulphide concentrates, and in mine waste (tailing) disposal areas (Stachulak, 1990; Lukaszewski, 1969; Headley et al., 1977). Lukaszewski (1969), Farnsworth (1977), and Good (1977) note that sulphide minerals can act as fuel to promote underground mine fires. Based on such findings, sulphide minerals could become classified as hazardous materials, making transport of concentrates and storage of mine waste subject to stricter and more costly regulation. The problem is one the industry is keen to avoid."

Jan 1, 2009

By Orson Shepard

TEXTBOOKS on fire assaying list the following standard methods of assaying sulphide ores: (1) scorification, (2) litharge-niter, (3) soda-iron, (4) roasting, (5) combination wet and fire. The litharge-niter method has proved the most satisfactory, and is the usual method for assaying sulphide ores and concentrates. It gives good results when suitably conducted and when lead buttons of uniform size are produced so that the cupellation temperature can be properly controlled. The main objection to the method is the inconvenience of determining the amount of niter to add to each assay charge to produce lead buttons of suitable size from a set of fusions. For the assay of different materials, the niter requirement varies with the particular sulphide minerals present, the amount of sulphide minerals present, the slag composition, and the rate of heating the charge in the furnace. Except for some materials, so uniform in composition that the same amount of niter can be used in assaying all samples, the amount of niter must be determined for each sample to be assayed. This is done by either: (1) calculation from an estimate of the kind and amount of sul-phide minerals present in the sample, or (2) a preliminary fusion. Some assayers use one method and some the other. The estimation method takes the least time; but much experience is required to obtain close estimates on a wide variety of materials. At best, the sizes of the lead buttons obtained vary considerably. The preliminary fusion method usually gives lead buttons of fairly uniform size, although sometimes there is a variation because the oxidizing power of niter varies a little with the charge. This variation can be eliminated by two preliminary fusions: one to determine the reducing power of the ore, and the other to determine the oxidizing power of niter in the charge. The objection to the prelimi-nary fusion is the extra time and expense involved.

Jan 1, 1939

By S. Chander

A review of the published literature on the mechanism of depression of sulfide minerals shows that a unified theory is not yet available. The various mechanisms that have been postulated include competition between depressants and collectors to adsorb at the surface sites, creation of thermodynamic conditions nonconducive for formation of a metal collector salt or formation of a hydrophilic coating on the surface. The hydrophilic coating may or matt not effect the adsorption of collectors. In yet another mechanism, the depressant nay participate directly in oxidation/reduction reactions between collectors and sulfide minerals. Examples from the literature are discussed to highlight oxidation/reduction effects in the depression of sulfide minerals.

Jan 1, 1984

By G. Wren

As base metal sulphide resources become increasingly challenging to process, producers seek alternative options to treat concentrates. This study considers the mineral, elemental, and leaching character of a West Australian nickel sulphide deposit (Cosmos Nickel Project). After a brief review of the published work bench top leach tests were conducted to examine the factors which impact the kinetics of nickel sulphide leaching such as particle size, temperature, acid strength and type, concentration of copper sulphate and sodium chloride, and oxygen partial pressure. The effect of sodium chloride was considered due to the common occurrence of hyper saline water at West Australian nickel sulphide mine sites. Ultrafine grinding to an 80% passing size of 10 µm resulted in high nickel leaching efficiency. Moreover, higher concentrations of acid, copper(II) and sodium chloride also gave higher nickel and cobalt leaching efficiencies but arsenic precipitated as FeAsO4. Under the most suitable conditions the extractions of nickel, cobalt and arsenic at 90oC after 6 hours were >95%, 90% and <5%, respectively. The comparison with results from high pressure operations indicates the possibility of using a hydrometallurgical flowsheet based on fine grinding and atmospheric pressure leaching and warrants further investigations.

Jan 1, 2014

By H Y. Niu

The coal left in the goaf is easily submerged by groundwater damage. During the mining process of the underlying coal seam, it is necessary to drain the water in the overlying goaf. The coal sample is prone to spontaneous combustion after being soaked in water and air-dried. To explore the effect of micro-functional group transformation of water-immersed coal samples on the spontaneous combustion characteristics of coal samples during the low-temperature oxidation process. Using the experimental method of infrared spectroscopy, the migration law of special functional groups under different oxygen concentrations of water-soaked coal samples was analysed. By means of thermal analysis, the endothermic and exothermic properties of the functional groups in the water-soaked coal samples were studied. The results show that: the higher the oxygen concentration, the more oxygen-containing functional groups in the water-soaked coal sample, compared with the 18 per cent oxygen concentration, the 14 per cent oxygen concentration has a small increase, and the chain length is shortened. The temperature increase together with the oxygen concentration content determines the functional group content, the pyrolysis process produces some functional groups. The lower the oxygen concentration, endothermic rate decreases and endothermic temperature increases, the higher the ignition temperature of coal oxy-combustion, the lower the total heat release, the higher the burnout temperature, and the faster the oxygen-absorbing weight gain and the conversion of functional groups. Below 14 per cent oxygen concentration, the oxidative combustion process will be greatly reduced. The results provide a theoretical basis for preventing long-term water-soaked coal body oxidative spontaneous combustion in shallow buried coal seams.

Oct 12, 2022

By Michael J. Humenick

A laboratory experimental research project was conducted to evaluate the use of chlorine for the oxidative destruction of residual ammonia which may remain in ground water after in-situ uranium solution mining operations. The work tested the idea of the injection of high strength calcium hypochlorite solution into the mining zone to convert ammonia to nitrogen gas as a final clean-up process for ammonia removal from the ground water system. The paper details ammonia removal efficiency as a function of chlorine dose, reactant and product material balances, and how the concept may be used as a final ground water restoration process.

Jan 1, 1982

By B. Yawney

A copper-nickel sulfide concentrate was leached in water at about 2000C under oxygen pressures of about 0.35 MPa. Oxidation of sulfide to sulfate was virtually complete in about 30 minutes, resulting in greater than 95% copper and 98% nickel extractions. Leaching temperature was shown to be the most important factor affecting metal extractions. Measured rates of oxygen consumption were used to develop batch kinetic data. Mini-plant continuous pressure leaching tests agreed with batch leach results. A proposed overall flowsheet is briefly examined.

Jan 1, 1976

By Pollard D. M

Chalcopyrite samples from two different localities were leached in oxygenated mixed chloride-sulphate lixivants at elevated temperatures and atmospheric pressure. The oxidation of chalcopyrite was found to follow predominantly linear kinetics. The slope of the major region was dependent on stirring rate, oxygen flowrate and chloride concentration while only slightly dependent on the surface area of the sample leached. This region was found to predominate only at low temperatures. The oxidised chalcopyrite releases cuprous and ferric ions into solutions. Chloride ions complex these dissolved ions to effectively move the equilibrium of the leaching reaction to the right. When the level of chloride in solution was below 6 g/l, the unstable cuprous ions were found to reprecipitate with sulphur as covellite. When no chloride was present and the lixivant was a solution of sulphuric acid then ferric sulphates precipitated. The overall leaching reaction occurring in the leaching system is: CuFeS2 + 5H+ + 1.25 02 = Cu 2+ + Fe 3+ + 2S¦ + 2.5H20

Jan 1, 1987

By Ma Lianren, Wang Duolun, Chenzhe Li, Hongyan Xie, Fenglan Luo, Huixin Jin

In this study, the oxidation of low-grade pyrolusite to potassium manganate in alkaline solutions under O2 pressure has been investigated. The effects of different conditions on the high-grade and low-grade pyrolusite leaching process were investigated based on thermodynamic calculation, as well as the reaction mechanisms and kinetics of the low-grade pyrolusite during the leaching process. The results showed that the manganese conversion rates of the two types of pyrolusite were almost the same, and reaching 99% for high-grade pyrolusite and 96% for low-grade pyrolusite under optimal conditions. The optimum condition for low-grade pyrolusite sample JM-2 was achieved as 0.5 MPa of the oxygen partial pressure, 55% of KOH, 14 of the initial alkali-manganese ratio, and ≤ 48 μm of the mineral granularity at 260 °C within 150 min of leaching time and 500 rpm. In alkaline leaching of low-grade pyrolusite, Mn(IV) was oxidized into Mn(VI). The particles changed from large particles to flakes and finally formed crystals. Finally, the shrinking core model was used to fully describe the leaching kinetics of the manganese. It was demonstrated that the leaching of manganese was controlled by the chemical surface reactions and the activation energy which equals 115.9121 kJ/mol.

Dec 3, 2022

By F. Nava-Alonso, A. Uribe-Salas, C. Rodriguez-Rodriguez

Ozone has been proposed to pretreat refractory ores before the cyanidation process for precious metals extraction. As pyrargyrite is one of the silver species most common in Mexican refractory ores, the ozonization of this silver sulfide was studied. The effect of pH and ozone concentration on silver dissolution was evaluated by means of a factorial experimental design. Two levels of sulfuric acid concentration and ozone in gas concentration were evaluated: 0.18 and 0.72 mol/L of acid and 0.054 and 0.077 gO3/L, respectively. The highest silver dissolution was obtained when using the higher acid and ozone concentration.

Jan 1, 2011

By Patrick G. Hatcher

Studies of sedimentary humic acids by nuclear magnetic resonance (NMR), stable isotopes, and elemental analysis show they are derived by oxidative degradation of complex plant macromolecules that are insoluble in aqueous or organic solvents. The mechanism by which humic acids originate is fundamental to our understanding of the role of organic matter in ore deposition, because these substances can complex and mobilize a number of metal ions. The organic matter associated with uranium ores of the San Juan Basin, New Mexico and Carlin-type disseminated gold deposits of Nevada has certain organic geochemical characteristics that suggest an origin from humic acids.

Jan 1, 2013

By E. Maziar Sauber

In order to prepare a more desirable feedstock for a rare earth elements separation refinery, cerium, a penalty element in the refinery feedstock, should be removed from the mixed rare earth elements oxide or carbonate feedstock. In this study, cerium (III) to cerium (IV) oxidation by calcium hypochlorite and subsequent precipitation was used to remove cerium from a mixed rare earth elements chloride solution. A factorial design of experiments was used to determine the effect of process variables such as temperature, pH, and oxidizer addition on the oxidation of cerium (III) using synthetic solutions. Under certain test conditions, all of the cerium was successfully removed from the chloride solution, and some REE accompanied cerium and reported to the precipitate. This proposed technology can allow for low cost removal of cerium from mixed rare earth elements chlorides.

By C. K. C. K. Gupta

The rare earths in elemental form are required for a variety of scientific and technological purposes. They are not easily obtained in this form, due to the great chemical stability of the rare-earth compounds and the strong tendency of elemental metals to react with everything they come in to contact with, especially at high temperatures. Beginning in the 1950s, when sufficient quantities of separated rare earths became available, as the result of intense research and development, three processing routes were developed to accomplish the preparation of all 16 naturally occurring rare-earth elements. They are chemical reduction of the halide intermediates, the oxides and electrochemical reduction of chlorides and oxide-fluoride mixtures. Not all the processes are effective with all the rare earths. In spite of the celebrated similarity of trivalent rare earths, the physical properties of individual rare-earth elements are sufficiently different that a variety of techniques are required for their preparation. The development of reduction processes for the rare-earth metals are covered in this paper, with focus on the oxide reduction routes. The strong reliance of effective reduction processes on the fundamental science of reduction reactions is highlighted.