Search Documents

By C. F. Seaman, R. G. Clay

The mines of The Tennessee Copper Co. are in the Ducktown Basin, in southeastern Tennessee. The ore is a heavy sulphide consisting principally of chalcopyrite, pyrite and pyrrhotite and in places running as high as 95 per cent sulphur and iron. Operating mines are the Burra Burra and Eureka. Development ' of the Boyd ore body was started in 1940. Late in 1939 the decision was made to change from fuse and cap to all electric blasting and at the same time electric cap lamps were installed to replace carbide. These changes were made to improve the safety and working conditions in the mines. Both the Bureau of Mines and explosives manufacturers recommended electric blasting as a safety measure. Until that rime, electric blasting had been used only for shaft sinking and in places where it was absolutely essential for safety. Very few men had had experience in this type of blasting, as the places where it was required were those that also required direct supervision. It was necessary for the mining staff to work out methods, procedure, and equipment to be used. In this they were ably assisted by representatives of the explosives manufacturers. Many mistakes were made and it is the purpose of this paper to describe the original plan and installation, show the major difficulties encountered. the remedies applied, and present the practices now being followed. Comparison of costs of the two methods will also be discussed. About six months were required to make the change and eliminate fuse and cap blasting entirely. The first electric blasting stations were installed in November 1939 and the last fuse was taken underground in May 1940. A very unusual condition forced the use of fuse for a short time in one heading after May, but that will be discussed later. Original Equipment and Installation A power line is generally recommended as a source of current where permanent blasting stations are used. The plan worked out for electric blasting was to tap 220-volt alternating-current lines when they were available and use 250-volt direct current from the trolley wire at all other places. A blasting machine would be available at each shaft for places where there were no regular blasting stations and could be used if a regular station should fail. The equipment decided on was No. 16 duplex reinforced lamp cord for lines to within about 50 ft. of the working place and No. 20 lead wire from that point to the shots. An open double-pole, double-throw switch with slate base was put in the circuit, so connected that the down position would close the line to the shots 2nd the up position would connect it to the Iine from the power contactor. This switch was located in the circuit as close to the blast as was safe (should the shots explode when it was placed in the shooting

Jan 1, 1943

By R. G. Clay, C. F. Seaman

The mines of The Tennessee Copper Co. are in the Ducktown Basin, in southeastern Tennessee. The ore is a heavy sulphide consisting principally of chalcopyrite, pyrite and pyrrhotite and in places running as high as 95 per cent sulphur and iron. Operating mines are the Burra Burra and Eureka. Development ' of the Boyd ore body was started in 1940. Late in 1939 the decision was made to change from fuse and cap to all electric blasting and at the same time electric cap lamps were installed to replace carbide. These changes were made to improve the safety and working conditions in the mines. Both the Bureau of Mines and explosives manufacturers recommended electric blasting as a safety measure. Until that rime, electric blasting had been used only for shaft sinking and in places where it was absolutely essential for safety. Very few men had had experience in this type of blasting, as the places where it was required were those that also required direct supervision. It was necessary for the mining staff to work out methods, procedure, and equipment to be used. In this they were ably assisted by representatives of the explosives manufacturers. Many mistakes were made and it is the purpose of this paper to describe the original plan and installation, show the major difficulties encountered. the remedies applied, and present the practices now being followed. Comparison of costs of the two methods will also be discussed. About six months were required to make the change and eliminate fuse and cap blasting entirely. The first electric blasting stations were installed in November 1939 and the last fuse was taken underground in May 1940. A very unusual condition forced the use of fuse for a short time in one heading after May, but that will be discussed later. Original Equipment and Installation A power line is generally recommended as a source of current where permanent blasting stations are used. The plan worked out for electric blasting was to tap 220-volt alternating-current lines when they were available and use 250-volt direct current from the trolley wire at all other places. A blasting machine would be available at each shaft for places where there were no regular blasting stations and could be used if a regular station should fail. The equipment decided on was No. 16 duplex reinforced lamp cord for lines to within about 50 ft. of the working place and No. 20 lead wire from that point to the shots. An open double-pole, double-throw switch with slate base was put in the circuit, so connected that the down position would close the line to the shots 2nd the up position would connect it to the Iine from the power contactor. This switch was located in the circuit as close to the blast as was safe (should the shots explode when it was placed in the shooting

Jan 1, 1943

By William B. Senseman

For reasons well known to mining engineers, wet grinding is quite universal in plants having to do with the extraction of metallic values from crude ores. In the processing of the nonmetallic and industrial minerals, dry grinding is the more common method. The crude materials usually contain less moisture than is required for wet grinding and the products usually are marketed in dry form; most of them as powders. To grind wet, therefore, would entail the addition of water and an expense for drying the product, which is not justified. Furthermore, the material would be a dried cake that would still have to be pulverized or disintegrated before use. For producing fine products, air separators have largely replaced the earlier practice of sizing with screens and bolting reels. Mills in which the air-separating feature is an integral part of the design are now commonplace. Mill designs are many and air systems have developed along various lines, but for the purpose of this discussion, only the fundamental idea need be emphasized— the idea of using air for sizing and removing pulverized material from a grinding mill. About 20 years ago, when the use of mills equipped with air separation had become common practice, heated air or gas was introduced to such a system for the removal of moisture. The purpose of this discussion is to outline the developments and trends that have followed this experiment. It is an important development, for mills equipped with air separation are now universally used for pulverizing not only nonmetallic and industrial minerals, but a great variety of other materials. All such mills are essentially the same. Dried material is pulverized, removed by an air stream, trapped in a cyclone collector, and relatively clean air from the cyclone is returned through a fan to the mill. There is no theoretical need for a vent from the system. The practical need is to vent the air that leaks into the system, and, since the cyclone is not 100 per cent efficient as a dust collector, this vented air carries some dust with it. The initial attempt at drying was made on a system like that described, by the addition of a furnace. The minus pressure within the mill draws hot gas from the furnace. Infiltration air, along with the drying gases and evaporated moisture, is vented as before. The first application was made to a mill used for pulverizing coal. The coal contained very little moisture, so very little drying effect was needed for the success of this experiment. Actually, some calculated efficiencies of over 100 per cent were obtained before due allowance was made for the conversion of mill power into useful heat. When moisture is low, the heat obtained from the conversion of mill power is an appreciable part of that required. That drying can be effected in the short time interval available in a grinding mill of this type is better understood by visual-

Jan 1, 1947

By William B. Senseman

For reasons well known to mining engineers, wet grinding is quite universal in plants having to do with the extraction of metallic values from crude ores. In the processing of the nonmetallic and industrial minerals, dry grinding is the more common method. The crude materials usually contain less moisture than is required for wet grinding and the products usually are marketed in dry form; most of them as powders. To grind wet, therefore, would entail the addition of water and an expense for drying the product, which is not justified. Furthermore, the material would be a dried cake that would still have to be pulverized or disintegrated before use. For producing fine products, air separators have largely replaced the earlier practice of sizing with screens and bolting reels. Mills in which the air-separating feature is an integral part of the design are now commonplace. Mill designs are many and air systems have developed along various lines, but for the purpose of this discussion, only the fundamental idea need be emphasized— the idea of using air for sizing and removing pulverized material from a grinding mill. About 20 years ago, when the use of mills equipped with air separation had become common practice, heated air or gas was introduced to such a system for the removal of moisture. The purpose of this discussion is to outline the developments and trends that have followed this experiment. It is an important development, for mills equipped with air separation are now universally used for pulverizing not only nonmetallic and industrial minerals, but a great variety of other materials. All such mills are essentially the same. Dried material is pulverized, removed by an air stream, trapped in a cyclone collector, and relatively clean air from the cyclone is returned through a fan to the mill. There is no theoretical need for a vent from the system. The practical need is to vent the air that leaks into the system, and, since the cyclone is not 100 per cent efficient as a dust collector, this vented air carries some dust with it. The initial attempt at drying was made on a system like that described, by the addition of a furnace. The minus pressure within the mill draws hot gas from the furnace. Infiltration air, along with the drying gases and evaporated moisture, is vented as before. The first application was made to a mill used for pulverizing coal. The coal contained very little moisture, so very little drying effect was needed for the success of this experiment. Actually, some calculated efficiencies of over 100 per cent were obtained before due allowance was made for the conversion of mill power into useful heat. When moisture is low, the heat obtained from the conversion of mill power is an appreciable part of that required. That drying can be effected in the short time interval available in a grinding mill of this type is better understood by visual-

Jan 1, 1947

By Clarence W. Balke

Small buttons of fused tantalum have been produced by are fusion in a vacuum, by drawing an arc between sticks of pressed tantalum and a tantalum-faced water-cooled copper block. However, ingots of appreciable size can be produced only by the heat-treatment of bars pressed from powder. The following outline covering the production of finished bars of tantalum by the methods of powder metallurgy is also used for the production of columbium, taking into account the difference in the melting points of these two metals. Pressing the Powder With possibly a few exceptions, a pressing operation is one of the essential steps in the practice of powder metallurgy. In fact, the author's experience with a number of high-melting-point metals and with numerous types of hard carbide compositions has led him to believe that this operation is often one of the most important in the entire process, and frequently one of the most difficult to carry out in a satisfactory manner. Defects due to improper pressing can readily lead to a defective finished product. It is the author's opinion that rarely is a bar or other article pressed from metal powder in such a way that all parts of the piece are uniformly pressed. The nearest approach to uniformity of pressing is possibly attained when the powder is contained in a flexible receptacle, such as rubber, and is pressed under a liquid by hydrostatic pressure. However, this method is not generally applicable. Hydraulic pressing in steel dies where one or two punches are forced into the die must usually be resorted to. As the pressure in such a die is built up, the powder begins to cling to the walls of the die with a tenacity dependent upon the nature of the powder, and this results in a bridging action, so that the layers of powder adjacent to the moving punch are pressed more heavily than those further removed in the mass. Frequently, as the pressure is carried higher, there may be a mass slippage of the powder upon itself, with the result that slip cracks are formed within the pressed

Jan 1, 1938

By Clarence W. Balke

Small buttons of fused tantalum have been produced by are fusion in a vacuum, by drawing an arc between sticks of pressed tantalum and a tantalum-faced water-cooled copper block. However, ingots of appreciable size can be produced only by the heat-treatment of bars pressed from powder. The following outline covering the production of finished bars of tantalum by the methods of powder metallurgy is also used for the production of columbium, taking into account the difference in the melting points of these two metals. Pressing the Powder With possibly a few exceptions, a pressing operation is one of the essential steps in the practice of powder metallurgy. In fact, the author's experience with a number of high-melting-point metals and with numerous types of hard carbide compositions has led him to believe that this operation is often one of the most important in the entire process, and frequently one of the most difficult to carry out in a satisfactory manner. Defects due to improper pressing can readily lead to a defective finished product. It is the author's opinion that rarely is a bar or other article pressed from metal powder in such a way that all parts of the piece are uniformly pressed. The nearest approach to uniformity of pressing is possibly attained when the powder is contained in a flexible receptacle, such as rubber, and is pressed under a liquid by hydrostatic pressure. However, this method is not generally applicable. Hydraulic pressing in steel dies where one or two punches are forced into the die must usually be resorted to. As the pressure in such a die is built up, the powder begins to cling to the walls of the die with a tenacity dependent upon the nature of the powder, and this results in a bridging action, so that the layers of powder adjacent to the moving punch are pressed more heavily than those further removed in the mass. Frequently, as the pressure is carried higher, there may be a mass slippage of the powder upon itself, with the result that slip cracks are formed within the pressed

Jan 1, 1938

By Newell G. Alford

The data in this paper were collected to show both the volume and speed with which bituminous mines have indefinitely suspended operation while economic advantage in the industry has so gravely declined. The study was limited to the bituminous coal-mining states east of the Mississippi River, wherein conditions affecting production and demand are more common respectively to all of the mining districts included and represent about 95 per cent of the nation's coal mining. Data for the compilation of these statistics and for the construction of these graphs have been obtained in all cases from state mine department reports, except from those of Ohio and Virginia. In Virginia essential individual mine data were secured from an authentic source, but no individual Ohio mine information is obtainable, because all Ohio fact-gathering agencies are prohibited by law from revealing such data. In other states the facts were tabulated and later checked with the cooperation of Chief Mine Inspectors. In all, excluding Ohio, over 17,000 individual annual mine returns were examined. Special information was secured from each state mine department about suspensions in 1932. Accurate information was not available from all states about nine abandonment due to exhaustion of coal reserves, and while these were completed for several states, it has not been shown because it was not perfected for all states. However, the total observed sample mas comprehensive enough to show that exhaustion accounts for a very limited part of the suspended production. Wherever mention is made of '(suspended productionJ' the largest annual output of the mine in the five years prior to suspension has been taken as the measure of its probable production had it continued to operate. A mine is not regarded in this category, as having suspended, when it merely ceases to produce. The word "suspension" is used only where there is a complete abandonment of activity for an indefinite period, as evidenced by the fact that both ventilation and pumping are discontinued.

Jan 1, 1934

By Reamy Joyce

Conditions in underground mining are so variable that in approaching the problem of the economies effected by the use of pressure-treated mine ties and mine timbers, it is necessary to secure specific data for each mine. Facts must first be dug out to show the service life of untreated timber and the reason for its failure. Generally speaking, decay is the usual cause of failure, but in some mines mechanical destruction is an important factor. Occasionally the two causes combine to produce fail-urrs, and it is difficult to determine positively which factor is responsible. In making comparisons, it is always necessary to start with the cost in place and for this reason there must be accurate information covering the labor cost of installation and the labor cost of renewals. When treated timber is used, it is necessary to know the specifications for the treating process, whether the timber was painted, dipped, treated open tank, or impregnated under pressure according to standard specifications. It is also necessary to know the preservative used and the amount of the preservative that was retained by the timber after treatment. It is also well to know whether the timber was thoroughly air-seasoned before treatment or was green at the time it was treated. The kind of timber available, both untreated and treated, must be known and all of the factors listed above must be taken into consideration in the study of any problem. Variable Conditions A study was made recently of the untreated mine ties used by a bituminous coal company in two of its mines, which are about 20 miles apart. The mine ties were secured from the same sources for both mines. A careful check was made over a 10-yr. period on the life of untreated main-haulage ties, and it was found that in the mine where the haulage roads were on intake air the average life was approximately 5 yr., while in the other mine, where the haulage roads were on return air, the average life was 2 yr. A similar variability in untreated timber

Jan 1, 1940

By Reamy Joyce

Conditions in underground mining are so variable that in approaching the problem of the economies effected by the use of pressure-treated mine ties and mine timbers, it is necessary to secure specific data for each mine. Facts must first be dug out to show the service life of untreated timber and the reason for its failure. Generally speaking, decay is the usual cause of failure, but in some mines mechanical destruction is an important factor. Occasionally the two causes combine to produce fail-urrs, and it is difficult to determine positively which factor is responsible. In making comparisons, it is always necessary to start with the cost in place and for this reason there must be accurate information covering the labor cost of installation and the labor cost of renewals. When treated timber is used, it is necessary to know the specifications for the treating process, whether the timber was painted, dipped, treated open tank, or impregnated under pressure according to standard specifications. It is also necessary to know the preservative used and the amount of the preservative that was retained by the timber after treatment. It is also well to know whether the timber was thoroughly air-seasoned before treatment or was green at the time it was treated. The kind of timber available, both untreated and treated, must be known and all of the factors listed above must be taken into consideration in the study of any problem. Variable Conditions A study was made recently of the untreated mine ties used by a bituminous coal company in two of its mines, which are about 20 miles apart. The mine ties were secured from the same sources for both mines. A careful check was made over a 10-yr. period on the life of untreated main-haulage ties, and it was found that in the mine where the haulage roads were on intake air the average life was approximately 5 yr., while in the other mine, where the haulage roads were on return air, the average life was 2 yr. A similar variability in untreated timber

Jan 1, 1940

By D. K. Crampton, H. I. Burghoff, J. T. Stacy

The effect of cold-working upon electrical conductivity of copper and of copper alloys appears not to be generally known in detail. Although several papers on the subject have been presented, showing variable effects according to alloy composition, it is often assumed that the 2 to 3 per cent lowering of the conductivity of ordinary tough-pitch copper by severe cold-working is typical for copper alloys. Because of this situation it was decided to carry out the present work upon several types of copper, copper-zinc alloys over the commercial range of brasses, other binary alloys, and numerous age-hardening alloys in the quenched, and quenched and aged conditions. The large number of alloys investigated made it impossible to study every one in the detail it may have merited. Inasmuch as several interesting points that could not be satisfactorily explained came to light, further work is contemplated by the authors. It is usually considered that the normal effect of cold-work on ductile metals and unordered alloys is to decrease conductivity slightly. In alloys that are in the ordered state, as annealed or otherwise heat-treated, cold--working tends to disorder the structure, resulting in very marked lowering of conductivity. The random state of atomic arrangement produces lower con- ductivity than the ordered state for the same composition.1 Previous Work Previous work in the authors' laboratory has shown the electrical conductivity of several copper alloys to be decreased by greater amounts than might have been expected, in view of the general knowledge on the subject, when cold-worked. Guillet and Ballay2 investigated the influence of cold-work upon the resistivity of several metals and alloys, including copper and some copper alloys. The increase of resistivity due to severe working w is less than 4 per cent for all pure metals tested, while the increases for the alloys were generally higher. In the copper-zinc alloys, they found that the increase of resistance due to drawing increased with zinc content, and reported a 21.7 per cent increase of resistance for an alloy contaiiiing 67.9 per cent Cu as severely worked. Masima and Sachs3 studied the change in electrical resistance of three brass crystals when stretched in the tensile test, obtaining increases in resistance of the order of 3 per cent for 30 to 40 per cent reduction of area of the specimens. The resistance decreased again when the cold-worked crystals were subsequently annealed. Bardenheuer and Schmidt4 found that the conductivity of copper was decreased by 3 to 4 per cent when reduced 50 per cent by working. The conductivity of 72-28

Jan 1, 1941

By D. K. Crampton, H. I. Burghoff, J. T. Stacy

The effect of cold-working upon electrical conductivity of copper and of copper alloys appears not to be generally known in detail. Although several papers on the subject have been presented, showing variable effects according to alloy composition, it is often assumed that the 2 to 3 per cent lowering of the conductivity of ordinary tough-pitch copper by severe cold-working is typical for copper alloys. Because of this situation it was decided to carry out the present work upon several types of copper, copper-zinc alloys over the commercial range of brasses, other binary alloys, and numerous age-hardening alloys in the quenched, and quenched and aged conditions. The large number of alloys investigated made it impossible to study every one in the detail it may have merited. Inasmuch as several interesting points that could not be satisfactorily explained came to light, further work is contemplated by the authors. It is usually considered that the normal effect of cold-work on ductile metals and unordered alloys is to decrease conductivity slightly. In alloys that are in the ordered state, as annealed or otherwise heat-treated, cold--working tends to disorder the structure, resulting in very marked lowering of conductivity. The random state of atomic arrangement produces lower con- ductivity than the ordered state for the same composition.1 Previous Work Previous work in the authors' laboratory has shown the electrical conductivity of several copper alloys to be decreased by greater amounts than might have been expected, in view of the general knowledge on the subject, when cold-worked. Guillet and Ballay2 investigated the influence of cold-work upon the resistivity of several metals and alloys, including copper and some copper alloys. The increase of resistivity due to severe working w is less than 4 per cent for all pure metals tested, while the increases for the alloys were generally higher. In the copper-zinc alloys, they found that the increase of resistance due to drawing increased with zinc content, and reported a 21.7 per cent increase of resistance for an alloy contaiiiing 67.9 per cent Cu as severely worked. Masima and Sachs3 studied the change in electrical resistance of three brass crystals when stretched in the tensile test, obtaining increases in resistance of the order of 3 per cent for 30 to 40 per cent reduction of area of the specimens. The resistance decreased again when the cold-worked crystals were subsequently annealed. Bardenheuer and Schmidt4 found that the conductivity of copper was decreased by 3 to 4 per cent when reduced 50 per cent by working. The conductivity of 72-28

Jan 1, 1941

By Tracy C. Jarrett

In 14-karat gold alloys, as in 10-karat gold alloys,3 the addition of such metals as zinc, nickel, copper and silver produces a wide range of physical and chemical properties such as color, hardness, corrosion resistance and melting points. These important factors made gold alloys desirable in the optical work and for jewelry. In 14-karat gold alloys, as well as in 10-karat or 12-karat, it is possible to have two golds of the same color, one of which will corrode more than the other, although it may be harder. Some of these alloys have been investigated by F. E. Carter,' E. M. Wise,= and L. Sterner Rainer.4 In this group of alloys the gold content of 58.3 per cent (14-karat) was held constant, while the copper varied from 36 to 24 per cent. The balance of the alloy consisted of one, two, or three of the metals silver, zinc, and nickel. All the alloys were melted in an induction furnace and cast into an ingot that measured 3 by 1/4 by 3/4 in. The method of determining the melting points, color determinations and acid test have been discussed in previous papers by the author.2, 3 It is necessary to use small test bars (Fig. I). The tensile bars were annealed at 1300oF. for 20 min. and then air-cooled. There being a very marked drop when the yield point was reached, "the drop of the beam" method was used in determining the yield point. Alloys Gold-copper.zilzc A~loys.—Gold-copper-zinc alloys melt, cast, and labricate easily. The low melting points, however, limit their use to some extent. The physical properties of these alloys are not entirely satisfactory. When the ultimate strength is satisfactory, the elongation and reduction of area are too low (Table I). Gold-copper-sinr-nickel A lloys.—In this group of alloys, in which zinc and nickel replace copper in approximately equal parts (Table I), the yield point, hardness, and ultimate strength increase with the increase of zinc and nickel content, while the reduction of area and elongation decrease. The physical properties are desirable, particularly of the white gold alloys. The alloys of this group are not difficult to cast and fabricate, and most of these colors could be used commercially. Gold-copper-nickel A lloys.—Gold-copper-nickel alloys are similar to the gold-copper-zinc and the gold-copper-zinc-nickel alloys. They do, however, possess high yield point, ultimate strength and hardness, somewhat higher than those of the other two groups mentioned (Table I). The difficulty with these alloys is that they fire-crack readily and heavy rolling is necessary between annealings. Being hard to fabricate, many

Jan 1, 1941

By Tracy C. Jarrett

In 14-karat gold alloys, as in 10-karat gold alloys,3 the addition of such metals as zinc, nickel, copper and silver produces a wide range of physical and chemical properties such as color, hardness, corrosion resistance and melting points. These important factors made gold alloys desirable in the optical work and for jewelry. In 14-karat gold alloys, as well as in 10-karat or 12-karat, it is possible to have two golds of the same color, one of which will corrode more than the other, although it may be harder. Some of these alloys have been investigated by F. E. Carter,' E. M. Wise,= and L. Sterner Rainer.4 In this group of alloys the gold content of 58.3 per cent (14-karat) was held constant, while the copper varied from 36 to 24 per cent. The balance of the alloy consisted of one, two, or three of the metals silver, zinc, and nickel. All the alloys were melted in an induction furnace and cast into an ingot that measured 3 by 1/4 by 3/4 in. The method of determining the melting points, color determinations and acid test have been discussed in previous papers by the author.2, 3 It is necessary to use small test bars (Fig. I). The tensile bars were annealed at 1300oF. for 20 min. and then air-cooled. There being a very marked drop when the yield point was reached, "the drop of the beam" method was used in determining the yield point. Alloys Gold-copper.zilzc A~loys.—Gold-copper-zinc alloys melt, cast, and labricate easily. The low melting points, however, limit their use to some extent. The physical properties of these alloys are not entirely satisfactory. When the ultimate strength is satisfactory, the elongation and reduction of area are too low (Table I). Gold-copper-sinr-nickel A lloys.—In this group of alloys, in which zinc and nickel replace copper in approximately equal parts (Table I), the yield point, hardness, and ultimate strength increase with the increase of zinc and nickel content, while the reduction of area and elongation decrease. The physical properties are desirable, particularly of the white gold alloys. The alloys of this group are not difficult to cast and fabricate, and most of these colors could be used commercially. Gold-copper-nickel A lloys.—Gold-copper-nickel alloys are similar to the gold-copper-zinc and the gold-copper-zinc-nickel alloys. They do, however, possess high yield point, ultimate strength and hardness, somewhat higher than those of the other two groups mentioned (Table I). The difficulty with these alloys is that they fire-crack readily and heavy rolling is necessary between annealings. Being hard to fabricate, many

Jan 1, 1941

By Tracy C. Jarrett

In making gold alloys possessing certain physical properties, such i~nportant factors as corrosion resistance, color, hardness and melting points must be considered. All of these requirements depend directly upon the composition. It is possible to obtain the same colored gold alloy by using different compositions, but in doing so one may bring in some undesirable property. Other investigations have been carried on in this field by F. E. Carter,' E. M. Wise12 and L. Sterner-Rainer2 To make a complete study of the effect of composition upon these properties, a systematic investigation was carried on involving a range of copper content from 85 to 65 per cent. Elements such as zinc, silver and nickel were used to replace in part the copper content. The gold content in all the alloys remained constant. Only 10-karat gold alloys of those containing 41.6 per cent gold will be considered. All of the alloys were made in an induction furnace. Each alloy was cast in a 3 by 1/4 by 3/4-in. ingot. The method of obtaining the melting points and making color determinations was described in a previots paper.4 The Rockwell B scale with the 1/16-in. ball and 100-kg. weight was used for all hardness determinations. The submersion of test pieces in concentrated nitric acid is one of the standard corrosion tests used in the optical trade. A test piece in the 50 per cent cold-worked condition, % by 2 by 0.045 in., is blanked from a skip using a die, and the weight loss per square inch of surface is taken as a means of comparison. The time for this test is 2 1/2 hr. of actual submersion of the test picce in the acid. This standard test was applied to all of the 10-karat gold alloys discussed in this paper. The tensile tests were made upon strips of the dimensions shown in Fig. 1. The test pieces after blanking were annealed at 1300" F. for 20 min. and cooled in air. Thc "drop of the beam" method was used in determining the yield point, as there was a very marked "drop" when the yield point was reached.

Jan 1, 1940

By Tracy C. Jarrett

In making gold alloys possessing certain physical properties, such i~nportant factors as corrosion resistance, color, hardness and melting points must be considered. All of these requirements depend directly upon the composition. It is possible to obtain the same colored gold alloy by using different compositions, but in doing so one may bring in some undesirable property. Other investigations have been carried on in this field by F. E. Carter,' E. M. Wise12 and L. Sterner-Rainer2 To make a complete study of the effect of composition upon these properties, a systematic investigation was carried on involving a range of copper content from 85 to 65 per cent. Elements such as zinc, silver and nickel were used to replace in part the copper content. The gold content in all the alloys remained constant. Only 10-karat gold alloys of those containing 41.6 per cent gold will be considered. All of the alloys were made in an induction furnace. Each alloy was cast in a 3 by 1/4 by 3/4-in. ingot. The method of obtaining the melting points and making color determinations was described in a previots paper.4 The Rockwell B scale with the 1/16-in. ball and 100-kg. weight was used for all hardness determinations. The submersion of test pieces in concentrated nitric acid is one of the standard corrosion tests used in the optical trade. A test piece in the 50 per cent cold-worked condition, % by 2 by 0.045 in., is blanked from a skip using a die, and the weight loss per square inch of surface is taken as a means of comparison. The time for this test is 2 1/2 hr. of actual submersion of the test picce in the acid. This standard test was applied to all of the 10-karat gold alloys discussed in this paper. The tensile tests were made upon strips of the dimensions shown in Fig. 1. The test pieces after blanking were annealed at 1300" F. for 20 min. and cooled in air. Thc "drop of the beam" method was used in determining the yield point, as there was a very marked "drop" when the yield point was reached.

Jan 1, 1940

By John Chipman, Carl F. Floe

A year ago the authors published a paper on the solubility of sulphur dioxide in molten copper.l The data in that paper agreed closely with that obtained by previous investigators, which, however, did not agree with the theoretical predictions for solubility of triatomic gases of this type. It has generally been assumed that the reaction of solution is: 6Cu(l) + SO2(g) = Cu2S (in Cu) + 2 Cu2O (in Cu) [I] _ (CU2S)(CU2O)2 K = (Cu)6(Pso2) [2] Neglecting the slight change in copper concentration and considering that the concentrations of sulphur and oxygen are both proportional to the volume of gas absorbed, it follows that this volume should be proportional to the cube root of the pressure. It was found that a plot of the volume absorbed versus the cube root of the pressure gave a straight line, but that this line did not pass through the origin. Calculations of the equilibrium constant for the reaction showed that it was fairly constant for pressures above 100 mm. but that actually it approached zero at lower pressures. The conclusion was made therefore that the solubility as determined could not be expressed by Eq. I or by any other simple equation, particularly at low pressures. Other investigators have concluded that the solubility of sulphur dioxide in copper as well as in several copper alloys is more nearly proportional to the square root of the pressure.* Such a conclusion, however, does not satisfactorily account for the results, even when rather complicated mechanisms for the solution are assumed. The highly improbable speculations of Lepp2 and of Schneider and Esch3 based upon hypothetical dissociation pressures of Cu2O and CU2S dissolved in copper illustrate the type of reasoning that has been used to account for the discrepancy. In the discussion of the previous paper, the authors pointed out that the discrepancy might possibly be due to impurities in the copper, although the purest form available was used. Further consideration of the problem suggested that the impurities likely to have the greatest effect on the solubility of so2 in copper were oxygen, sulphur and carbon. Accordingly, further experiments have been made to show the effects of these elements. Experimental Methods The apparatus used for measuring solubility was essentially the same as that shown in the previous paper. However, since it was desired to make measurements at low pressures, a McLeod gauge was added and 6-mm. glass tubing was substituted for the capillary. This increased the "hot volume" considerably but was necessary in order to obtain good vacuums in a reasonable length of time. A mercury diffusion pump was also installed.

Jan 1, 1942

By Carl F. Floe, John Chipman

A year ago the authors published a paper on the solubility of sulphur dioxide in molten copper.l The data in that paper agreed closely with that obtained by previous investigators, which, however, did not agree with the theoretical predictions for solubility of triatomic gases of this type. It has generally been assumed that the reaction of solution is: 6Cu(l) + SO2(g) = Cu2S (in Cu) + 2 Cu2O (in Cu) [I] _ (CU2S)(CU2O)2 K = (Cu)6(Pso2) [2] Neglecting the slight change in copper concentration and considering that the concentrations of sulphur and oxygen are both proportional to the volume of gas absorbed, it follows that this volume should be proportional to the cube root of the pressure. It was found that a plot of the volume absorbed versus the cube root of the pressure gave a straight line, but that this line did not pass through the origin. Calculations of the equilibrium constant for the reaction showed that it was fairly constant for pressures above 100 mm. but that actually it approached zero at lower pressures. The conclusion was made therefore that the solubility as determined could not be expressed by Eq. I or by any other simple equation, particularly at low pressures. Other investigators have concluded that the solubility of sulphur dioxide in copper as well as in several copper alloys is more nearly proportional to the square root of the pressure.* Such a conclusion, however, does not satisfactorily account for the results, even when rather complicated mechanisms for the solution are assumed. The highly improbable speculations of Lepp2 and of Schneider and Esch3 based upon hypothetical dissociation pressures of Cu2O and CU2S dissolved in copper illustrate the type of reasoning that has been used to account for the discrepancy. In the discussion of the previous paper, the authors pointed out that the discrepancy might possibly be due to impurities in the copper, although the purest form available was used. Further consideration of the problem suggested that the impurities likely to have the greatest effect on the solubility of so2 in copper were oxygen, sulphur and carbon. Accordingly, further experiments have been made to show the effects of these elements. Experimental Methods The apparatus used for measuring solubility was essentially the same as that shown in the previous paper. However, since it was desired to make measurements at low pressures, a McLeod gauge was added and 6-mm. glass tubing was substituted for the capillary. This increased the "hot volume" considerably but was necessary in order to obtain good vacuums in a reasonable length of time. A mercury diffusion pump was also installed.

Jan 1, 1942

By Richard S. McCaffery, Joseph F. Oesterle, Oscar O. Fritsche

The method of obtaining the data on which this paper is based is explained in detail in the paper on Determination of Viscosity of Iron Blast-furnace Slags.' The work was made possible by a grant of funds from Engineering Foundation, and it gives the results now obtained, continuing the general subject of our previous work and reported in former papers2 The data experimentally obtained are in the form of a temperature-viscosity curve for any slag of particular composition. (See Fig. 1.) From these curves, the viscosity of a slag of a definite composition and at a definite temperature is taken off and is plotted on a plane triaxial diagram showing compositions of silica lime and alumina on a plane representing constant-magnesia content (Fig. 4). The temperatures at which these results were plotted are 1300°, 1350°, 1400°, 1450°, 1500°, 1550" and 1600" C. and since the constant magnesia plane sections were an even 1 per cent. magnesia apart, magnesia analyses not of even unit magnesia composition were projected to these even unit magnesia planes. For example, 1.78 per cent. magnesia and 2.35 per cent. magnesia were projected to the 2 per cent. magnesia plane. The triaxial diagrams on which this first plotting was made were drawn on celluloid sheets, a transparent material on which it was easy to draw. When all the experimental work was plotted on celluloid in this way, the sheets representing a definite temperature were stacked in the proper order and were examined by transmitted light. Where

Jan 1, 1932

By Earl W. Palmer, Cyril Stanley Smith

StKip of any of the metals used for deep drawing operations occasionally yields cups that are defective because of a rim that varies in height around the cup in a wave-like manner. Some such defects are traceable to tools or other press factors, but when the protuberances formed (usually four in number on brass and other copper alloys) are symmetrically disposed with respect to the rolling direction of the strip, they are invariably attributable to the metal. The effect is known as "earing" and the protuberances are called "ears." Other terms frequently heard are "tips," "scallops," and "corners." It is recognized that the effect is most commonly a result of a directional crystal structure produced by rolling and annealing operations in the manufacture of the metal strip. Numerous papers dealing with various aspects of the earing effect have appeared in the literature, those listed in the references1 being especially interesting and valuable. An investigation of the factors influencing earing of brass cups has been in progress in the laboratories of the American Brass Co. for several years, and it was thought desirable to make some of the results generally available in summarized form. The present paper discusses many factors that do and do not contribute to ear formation. In addition, a section is devoted to methods of minimizing the earing tendency of brass sheet by proper selection of the cold-rolling and annealing schedule by which it is produced. In the space available, it is impossible to quote detailed experimental procedures and numerical results. However, the authors make no statement that they do not believe to be properly substantiated, either by experimental evidence obtained under laboratory conditions or by experience in the actual production of deep-drawing brass in the brass mill. Mechanism of Ear Formation It must be clearly understood that the formation on cups of symmetrical ears, four or more in number, is attributable solely to the strip metal, and results from the strip having different deformation characteristics in different directions. The tools used in the drawing process, or the type and completeness of lubrication of the strip, have nothing to do with the problem of ears, although they do, of course, greatly affect the "drawing quality" of the strip and the general appearance of the cup. A single tip may be drawn up on the rim of a cup because of misalignment of the tools, or because the gauge of metal varies from side to side of the strip. The two-ear form that sometimes appears is also traceable to gauge variations. However, the four-ear and six-ear symmetrical forms that we are concerned with here are caused by factors inherent in the structure of the metal itself.

Jan 1, 1942

By Cyril Stanley Smith, Earl W. Palmer

StKip of any of the metals used for deep drawing operations occasionally yields cups that are defective because of a rim that varies in height around the cup in a wave-like manner. Some such defects are traceable to tools or other press factors, but when the protuberances formed (usually four in number on brass and other copper alloys) are symmetrically disposed with respect to the rolling direction of the strip, they are invariably attributable to the metal. The effect is known as "earing" and the protuberances are called "ears." Other terms frequently heard are "tips," "scallops," and "corners." It is recognized that the effect is most commonly a result of a directional crystal structure produced by rolling and annealing operations in the manufacture of the metal strip. Numerous papers dealing with various aspects of the earing effect have appeared in the literature, those listed in the references1 being especially interesting and valuable. An investigation of the factors influencing earing of brass cups has been in progress in the laboratories of the American Brass Co. for several years, and it was thought desirable to make some of the results generally available in summarized form. The present paper discusses many factors that do and do not contribute to ear formation. In addition, a section is devoted to methods of minimizing the earing tendency of brass sheet by proper selection of the cold-rolling and annealing schedule by which it is produced. In the space available, it is impossible to quote detailed experimental procedures and numerical results. However, the authors make no statement that they do not believe to be properly substantiated, either by experimental evidence obtained under laboratory conditions or by experience in the actual production of deep-drawing brass in the brass mill. Mechanism of Ear Formation It must be clearly understood that the formation on cups of symmetrical ears, four or more in number, is attributable solely to the strip metal, and results from the strip having different deformation characteristics in different directions. The tools used in the drawing process, or the type and completeness of lubrication of the strip, have nothing to do with the problem of ears, although they do, of course, greatly affect the "drawing quality" of the strip and the general appearance of the cup. A single tip may be drawn up on the rim of a cup because of misalignment of the tools, or because the gauge of metal varies from side to side of the strip. The two-ear form that sometimes appears is also traceable to gauge variations. However, the four-ear and six-ear symmetrical forms that we are concerned with here are caused by factors inherent in the structure of the metal itself.

Jan 1, 1942