Search Documents

By C. Haycocks

The Appalachian coal fields contain many mineable contiguously placed coal seams. Selection of the mining sequence for these seams, historically and currently, is based primarily on considerations of seam ownership, availability and economics. Mining any seam can seriously affect subsequent operations in coal seams both above and below the one being mined. The effect is often detrimental to recovery costs and safety of mining in the subsequent seams. The purpose of this paper is to examine the conditions that can develop in an underlying seam due to stress concentrations that can occur below pillars or abutment zones in an overlying seam, and suggest guidelines for avoiding them. This situation most commonly occurs when the overlying seam is mined first, although simultaneous and subsequent mining of the upper seam can also produce such effects. Other interaction phenomena resulting from subsidence or arching will not be considered here. The methodology used in this research utilized both computer and body loaded photoelastic models to study the interaction mechanisms. Field studies are used in both interpretation and analysis of the results. Numerous examples of load transfer from upper workings exist in all parts of the world and many of these have been incorporated into this work. Such interaction problems are quite common and likely to be an ever increasing occurrence as mining activities in old seams are completed and new seams opened up.

Jan 1, 1982

By Joseph C. Zelanko, Anthony T. Iannacchione

One of the most difficult and longstanding engineering problems associated with coal mining is the catastrophic failure phenomenon known as coal mine bursts (known in the United States as bumps). For more than 70 years, researchers and practitioners have attempted to determine whether this destruction observed underground is caused by stress conditions within the coal pillar or from distant seismic sources in the mine roof and floor strata. The role of confinement and the extent of failure in solid pillars and panels have also proven difficult to define. These are important issues, since control solutions need to be based on a fundamental understanding of the problem. Obsenations by U.S. Bureau of Mines researchers over the last decade have helped to clarify certain aspects of these issues. Microseismic sensors and geomechanic field measurements have located areas of excess energy release, identified stress conditions in coalbeds close to failure, and recorded the response of mine structures prone to bursts. In the present study, data available for a range of U.S. bursts were considered in an effort to evaluate both common and distinctive features. Although the attempt revealed little commonality, encouraging results were produced by categorizing coal bursts by source mechanisms. When a coal burst is thus categorized, differences in environmental factors-such as geology, stress fields, and mining methods-are highlighted, and viable control strategies are readily recognized.

By D P. Sainsbury, J Western, B L. Sainsbury, V Mutton, P E. Petrie

Remnant rib pillars at Castlemaine Goldfields Ltd’s Ballarat Gold Project have been sterilised by the placement of loose rock fill in production stopes. The application of selectively injecting low-viscosity grout into the backfilled stopes to form a stabilised material has enabled recovery of the previously sterilised pillars. This paper outlines the engineering design, quality control and quality assurance program implemented to ensure the safe and efficient recovery of the rib pillars. The successful program included laboratory testing, numerical exposure stability modelling and in situ monitoring.CITATION:Sainsbury, B L, Sainsbury, D P, Western, J, Petrie, P E and Mutton, V, 2014. Pillar recovery adjacent to stabilised rock fill at the Ballarat Gold Project, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 77–86 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By V Mutton, L Potts, D Joyce

This paper describes the method of extracting sill pillars within the underground operation from under unconsolidated mullock fill at the Cracow Gold Mine. This pillar recovery method was initially successfully used to recover sill pillars at Crusader Mine, Western Australia in 2001. Globally significant resources have been sterilised due to the placement of loose rock fill above crown pillars and within adjacent stopes. The method described here offers significant opportunities to increase recovery of sill pillar recoveries.The royal orebody sill pillars at Cracow Gold Mine form a significant resource. Extraction of these pillars needed to be undertaken with minimal ore dilution and maximum ore recovery. The application that was selected to consolidate the loose mullock fill above each pillar used an injection grouting process (Minova FB200).Cracow Gold Mine mining method is bottom up bench mining. The pillars were left within the orebody to allow for stoping to commence whilst the decline was being developed. Due to the remainder of the orebody being extracted the only access to consolidate the backfill was from the sill pillar extraction level. Numerous problems were encountered and overcome from product selection and trial, system of injection to extraction.This pillar recovery process achieved a 95 per cent recovery of the sill pillar compared with an estimated 60 per cent typical for other mining options.CITATION:Potts, L, Mutton, V and Joyce, D, 2012. Pillar recovery at Cracow gold mine using grouted consolidated mullock, in Proceedings Narrow Vein Mining 2012 , pp 179-184 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 26, 2012

By The Mine Staff

THE PROPERTY of the Lamaque Mining Company, Limited, ?is located in the Town of Bourlamaque, seventy miles east of Noranda, in Bourlamaque township, Abitrbi county, north western Quebec. Gold production commenced at Lamaque in April, 1935, with an initial mill capacity of 250 tons per day. The capacity was doubled in November of the same year, and in December, 1937, it further increased to 1,200 tons per day. During the war years the mill operated at a reduced tonnage, but in 1951 milling units were added along with complementary crushing and shop facilities to bring the capacity to 1,500 tons per day. Finally, in 1953, the capacity was raised to 2,000 tons per day, which rate is being maintained at the present time. The total production at Lamaque from April 2nd, 1935, to December 31st, 1956, has been 9,168,901 tons of ore from which 2,208,168 ounces of gold was recovered. The total value of this production , excluding E.G. M.À.*, was $77,869,653.

Jan 1, 1957

By J. C. Irvine

Meramec Mining Company is a joint venture by Bethlehem Steel Corp. and St. Joe Minerals Corp. which mines and pelletizes iron ore at the Pea Ridge Mine. The Pea Ridge property is located near Sullivan, Missouri, about 70 miles southwest of St. Louis. The orebody was delineated in the mid-1950's by St. Joe during a lead exploration program. The first test holes drilled on the Pea Ridge magnetic anomaly revealed the presence of a large magnetite deposit; further drilling in 1956 and 1957 confirmed that the orebody was mineable, Meramec Mining Co. was incorporated in 1957 and shaft sinking began late in the year. Production commenced in April 1964. The orebody is overlain by about 1300 feet of flat-bedded sediments. It is tabular, about 2600 feet long and up to 600 feet thick. It dips about 80° and is of unknown depth. The ore is mainly high grade magnetite with small zones of specular hematite. The wall rock is a Precambrian rhyolite porphyry. The mine was initially started with five major levels on 150 foot intervals. Crosscuts were driven across the orebody on 190 foot centers. Banks of scopes were mined between the crosscuts by a modified shrinkage stoping method. This was done by undercutting a 40 foot wide by 150 foot long block and blasting horizontal "lifts" drilled on 5 foot intervals. A 65 foot still was left between levels which contained the slushing drift, fingers, crown pillar, and adequate thickness for support. By 1971 a ?lattice? of pillars had been left and mining had progressed to the point that an orderly pillar recovery program was necessary.

Jan 1, 1976

By Timothy D. Gardner, Christopher Mark

Coal mines in the Illinois Basin have not engaged in pillar recovery for many decades. In large part, this is due to the exceptionally weak nature of much of the roof in the region. But, as room-and-pillar mining is conducted at greater depths, and larger pillars become necessary, recovering them becomes more attractive. Recently a western Kentucky coal mine became the first in recent times to successfully employ full pillar recovery. This paper describes the many challenges that were overcome during the process. From the beginning, the focus was on protecting the miners from roof instability, using cable bolts, mesh, mobile roof supports (MRS), and engineered final stumps. Two short test panels were extracted first, and the results were used to adjust the support pattern and mining sequence. Further adjustments were made based on subsequent experience. To date, seven panels have been recovered without a ground fall injury.

Jul 1, 2023

By Theodore J. Barrett

[One of the earliest records of pillar removal can be found in the 16th Chapter of Judges in the Old Testament. Here we read where the mighty Sampson removed the pillars from beneath the prison house causing the collapse of the structure resulting in his own death along with the deaths of the 3,000 Philistine occupants. Our problems at the Mi Vida Mine differ somewhat from those of Sampson of old, in that it is our aim first to remove the pillars and get out from under the back before the "house falls in" and, secondly, to remove the pillars without the lose of a single life or without even a single casualty. As of January 15, 1959, the Mi Vida accident record stood at 772 days without a lost-time accident]

Jan 1, 1959

By Arthur H. Wilson

INTRODUCTION The stratified deposits of the coal measures are strongly laminated and exhibit a high degree of anisotropy. The stronger rocks in the sequence possess joints and shear planes, the coal itself has a closely spaced cleat pattern, and the softer rocks are capable of flowage. To calculate the general distribution of stress in such a medium by analytical means based on the theories of elasticity is difficult, and has not yet been satisfactorily achieved. Nevertheless, some estimate is required to aid the design of supporting pillars and permit the correct siting of main roadways. This is important when laying out districts for longwall extraction, particularly if the results of previous experience are not available in the area to be exploited. Although elastic stress analyses, including finite element analysis, may not be very appropriate, the basic equilibrium conditions will apply. These, combined with logical deductions based on observed fact, can be used to give appropriate solutions which experience has shown to be capable of giving acceptable results in the design of pillars associated with longwall workings. Constancy of cover load is one of the fundamental equilibrium conditions. When mining below ground, the cover is not removed, therefore the average vertical load after mining must equal the initial cover load. If mining produces a local decrease in load in any particular area, it must be balanced by an equivalent increase in load nearby. Bending moments in the strata above are capable of compensating for the turning moments which this redistribution of load may produce, and the existence of a "rear abutment", much discussed between 1950 and 1960, is not an essential equilibrium requirement. If the distribution of vertical stress is plotted three-dimensionally, then the load on any small element of area 6S will be o.6S, where o is the average stress. This also represents the volume of the "stress envelope" which lies above 6s. By making the individual areas very small and summing together, it is possible to show that the total load on any particular area can be found by calculating the volume of the stress distribution envelope which lies above it. A similar consideration applies to the stress distribution in a two-dimensional situation. If the stress distribution curve is drawn, then the area below any portion will represent the load per unit depth of section. For example, Figure 1 represents the possible stress distribution across a caved waste and associated ribside. If AW is the load deficiency [ ] These loads must balance, therefore area AW = AS, and if one can be deduced, the other will then be known. Attempts have been made to measure stress distributions in the ribside and in the waste. Stress meters in soft rocks such as the coal measures have not proved very effective. Those based on the measurement of strain have experienced difficulty in strata capable of flowage, high modulus stress meters suffer from cross sensitivity, and overcoming to obtain absolute stress is almost impossible. Load measuring instruments left in the waste have also proved largely ineffective, mainly as a result of the difficulties of protecting the leads in a caving environment. Certain logical deductions, however, can be made about the conditions in the waste. CONDITIONS IN THE WASTE Over the area of the waste the surface trough which develops is remarkably consistent, despite the geological variations which occur from coalfield to coalfield. In Britain, an accuracy of 210% is claimed for subsidence prediction based on width of extraction and depth of cover (National Coal Board, 1975). The subsidence in the USA is more variable (Adamek and Jeran, 1981), particularly with respect to the point of inflexion, but the same general pattern occurs. At the shallower depths the somewhat harder roof strata involved in the caving in the USA may suffer less compaction, giving reduced values of subsidence. Subsidence at intermediate horizons below the surface

Jan 1, 1982

By Dennis R. Dolinar, John L. Ellenberger, Gabriel S. Esterhuizen, Anthony T. Iannacchione

A survey of pillar conditions was carried out at 21 operating limestone mines that use the room-and-pillar method. The surveyed pillars were all located in rock that was classified as “Good” to “Very Good” using the RMR rock mass classification system. The average pillar width was 14.5m and the width to height ratio varied between 0.53 and 3.52. Pillar conditions were rated using a visual rating system that accounts for the effect of geological structures as well as stress related fracturing. Nine cases of pillar instability were recorded. Pillar instabilities were typically limited to individual pillars or small groups of pillars within an otherwise stable layout. Local geological structures such as inclined discontinuities or weak bedding planes contributed to instability in seven of nine cases that were observed. Elevated pillar stresses contributed to instability in the two remaining cases. All the unstable pillars observed had width-to-height ratios of less than 1.5. It is concluded that pillar instability is most likely to be caused by unfavorable geological structures in pillars with width to height ratios of less than 1.5. Stress related instability such as rib spalling becomes more prevalent when the average pillar stress approaches approximately 20 MPa.

By Gabriel S. Esterhuizen

A survey of pillar conditions was carried out at 21 operating limestone mines that use the room-and-pillar method. The surveyed pillars were all located in rock that was classified as ?Good? to ?Very Good? using the RMR rock mass classification system. The average pillar width was 14.5m and the width to height ratio varied between 0.53 and 3.52. Pillar conditions were rated using a visual rating system that accounts for the effect of geological structures as well as stress related fracturing. Nine cases of pillar instability were recorded. Pillar instabilities were typically limited to individual pillars or small groups of pillars within an otherwise stable layout. Local geological structures such as inclined discontinuities or weak bedding planes contributed to instability in seven of nine cases that were observed. Elevated pillar stresses contributed to instability in the two remaining cases. All the unstable pillars observed had width-to-height ratios of less than 1.5. It is concluded that pillar instability is most likely to be caused by unfavorable geological structures in pillars with width to height ratios of less than 1.5. Stress related instability such as rib spalling becomes more prevalent when the average pillar stress approaches approximately 20 MPa.

Jan 1, 2006

By J. A. Maritz

"The Hedley and Grant formulation for pillar strength has been widely adopted by the South Africa hard rock mining industry. Today, some forty year later, this formula still provides the foundation for pillar strength calculations when designing for stability and utilising pillars in mine layouts. Various mine specific back analyses were conducted to adjust the equation parameters based on underground observations of failed pillars and comparing to the pillar stresses calculated using numerical models. In all these instances, the influence of shear stresses was ignored. The key to more representative pillar strength estimation is a better understanding of the pillar loading environment.In this paper, special mining cases are evaluated and the existence of shear stresses on the pillar loading environment is illustrated. By revisiting some back analysis data for optimisation of the equation parameters, recommendations were made in respect of the influence of the shear stress component and on how this should be considered in determining the pillar strength.INTRODUCTIONCommon practice on flat dipping, shallow and intermediate depth ore deposits in the South African hard rock and coal mining industry is to exploit the mineral resource using a room-and-pillar layout. The design methodology is mainly based on a Factor of Safety (FoS) approach, where the strength of the pillar is compared to the effective load on the pillar. In these environments, FoS values of 1.6 are applied as it was found to correspond to a probability of failure in coal mines of 0.001. As discussed by Ryder and Jager (2002) page 279: “For lack of anything else more substantial, the figure of 1.6 is generally used in hard rock pillar design in South Africa”. Dependant on the designed purpose of the pillar, the FoS might be selected as high as 2.0 where long term stability is required. The factors directly influencing the FoS include the pillar height (which is linked to the mining height), effective pillar width, a rock-strength factor and extraction ratio."

Jan 1, 2015

By Ihsan Berk Tulu, Mustafa Can Suner

The synthetic rock mass (SRM) approach is a relatively new method to study the mechanical behavior of rock masses. Recently, an SRM approach was established to estimate pillar strength from laboratory scale to in-situ dimension using the two-dimensional Universal Distinct Element Code (UDEC). In this study, the developed methodology is applied to the S-Pillar database to estimate pillar strength and failure mechanisms as a function of width-to-height ratio of the pillars. First, stone mine rocks are categorized into three as low-, medium-, and high-strength according to their uniaxial compressive strength (UCS). Later, laboratory-scale intact rocks are scaled-up to the average in-situ pillar dimensions by explicitly considering the naturally existing joint sets. It is found that the strength of the pillars with low-UCS are overestimated when compared to pillars with high-UCS. This observation is attributed to the high joint density of the pillars with high-UCS. After obtaining in-situ pillar strength, the width-to-height ratios of the pillar models varied from 0.5 to 2.0 to gain a robust understanding of pillar mechanical behavior. Tensile failure is found to govern the pillar behavior with the width-to-height ratio of 0.5 while the combination of tensile failure in rib elements and shear failure in the core

By R. E. Lund

The design, operation, and performance of an integrated pilot plant for recovering zinc and copper from a complex sulfide ore are described. Metallurgical processing comprised selective sulfate roasting in a fluid bed, leaching in a weak sulfuring acid solution, recovering copper by cementation with scrap iron, air oxidation to remove soluble iron, more-or-less conventional purification for removal of impurities deleterious to zinc electrolysis, recovering zinc by electrolyzing solutions, and recycling spent electrolyte to the sulfating roaster. The effects of several feed preparation and roasting variables on the sulfation response of zinc, copper, and iron are set forth, together with the electrolyzing characteristics of the zinc solutions.

Jan 1, 1962

By Olgac Kangal, Ali Guney, Gulay Bulut, Guven Onal, Ayhan A. Sirkeci

This paper presents the results of pilot scale column flotation applications in the two different copper concentrators in Turkey. The Kure Copper Plant is located in the Black Sea Region of Turkey. In Kure, a very fine grinding requirement for an adequate level of liberation makes a successful flotation difficult and consequently the final concentrate can hardly assay above 16% Cu Column flotation tests were conducted at the plant site using two different column types The experiments proved that the grade of the concentrate could be increased from about 14% Cu to 25-26% Cu. Murgul Cakmakkaya Copper Concentrator is the largest copper concentrator in Turkey. Although concentrate production capacity is around 170,000 tons annually with 22-23% Cu content, this figure tends to be much lower than that. In Murgul a Turbo Column of Multotec Company of South Africa was employed. As a result of systematic column flotation tests, the grade of the concentrate was increased from 20.3% Cu to 28.7% Cu.

Jan 1, 2003

By T. Moloane, C. Bergman, Heloise Thiele

"A pilot test campaign was undertaken to evaluate dense medium cyclone separation efficiencies on samples of iron ore fines (-1mm +300µm). Evaluations were done using both gas and water atomised FeSi types across a range of operating conditions in the presence of slimes build-up. A Mineral Liberation Analyser (MLA) was used to measure size, density, shape and liberation data of DMS feed and products. The results of the test work were used to obtain parameters for modelling of the partition size/density response. The findings indicated that accurate density characterisation of the feed ore is essential in understanding product quality and recovery, particularly due to the effect of porosity and micro-inclusions. A significant off-set between cyclone underflow density and separation cut-point (D50) was found indicating that relatively low feed media densities (about 3.4g/cm3) are required to achieve high density cutpoints of over 4.0g/cm3. In agreement with CFD modelling, the separation quality is dominated by viscous effects, hence FeSi type and slimes content will need to be carefully controlled to ensure efficient separation.INTRODUCTION In the South African context, future resources of hematite are expected to be both of lower head grade and will contain a higher content of banded iron formation (BIF) (1). These ores may require finer crushing in order to liberate the high-grade fractions and will thus increase the amount of -1mm material to be processed. In order to efficiently upgrade these materials, it becomes necessary to re-examine both traditional and novel processes to treat material finer than 1mm in size. These include spiral and up-current classifiers, wet high intensity magnetic separation processes, Reflux classification and potentially includes dense medium separation (DMS). This study presents a technical evaluation of fines DMS using a mineralogically-based particle tracking analysis method (PTA) to calculate efficiencies of separation."

Jan 1, 2018

By K. Morin, C. -Y. Hon, G. Lachapelle

"Air-sampling results suggest drill operators working inside environmental drilling cabs at an open-pit gold mine in Nunavut, Canada, are at risk of exposure to asbestos and silica (quartz). The authors installed RESPA® CF Vortex HyperFLOW® units, which showed promising results under laboratory conditions. The goal was to evaluate the effectiveness of these units under actual working conditions. Personal and area air sampling was conducted in drilling cabs with and without the unit and a Wilcoxon rank-sum test was performed to compare the results. Particulate concentrations were significantly lower in drill cabs with a unit installed than in those without.RÉSUMÉ Selon les résultats d’une campagne d’échantillonnage de l’air, les foreurs travaillant dans des cabines de forage environnemental dans une mine d’or à ciel ouvert du Nunavut, au Canada, risquent d’être exposés à l’amiante et la silice (sous forme de quartz). Les auteurs ont installé des unités RESPA® CF Vortex HyperFLOW®, lesquelles of frent des résultats prometteurs en laboratoire. L’objectif est d’évaluer l’efficacité de ces unités dans des conditions de travail réelles. Des échantillons de l’air inhalé par le personnel et dans les aires de travail ont été évalués dans des cabines de foreuses équipées ou non de cette unité ; un test de Wilcoxon (également appelé test de la somme des rangs de Wilcoxon) a été mené afin de comparer les résultats. Les concentrations particulaires étaient considérablement plus faibles dans les cabines de foreuses équipées d’une unité que dans celles en étant dépourvues.INTRODUCTIONGenerally, mining operations are associated with a variety of occupational hazards. In an open-pit gold mine in Nunavut, Canada, drill operators are routinely exposed to asbestos (primarily amosite) and silica (quartz)—two naturally occurring substances in the ore that is to be drilled (Table 1). Inhalation is the primary route of exposure for these two hazards, which are associated with respiratory health effects such as asbestosis and silicosis, respectively. In addition, asbestos and silica are classified as human carcinogens by the International Agency for Research in Cancer (2001, 2011). Given the toxicity of these two agents, it is imperative that precautions be taken to minimize the risk of exposure of the mine’s workforce. To address this matter, the mine has an exposure-control plan, which includes the provision of personal protective equipment, personal hygiene facilities, training, and a medical surveillance program. Furthermore, the mine performs occupational exposure assessments or air sampling on a regular basis because the morphology of the ore changes rapidly with respect to asbestos and silica content."

Jan 1, 2017

By D. R. Kelland

A program has been carried out over the last two years to apply the technology of High Gradient Magnetic Separation (HGMS) to the problem of mineral beneficiation and specifically oxidized taconite iron ores. This program, supported by the RANN division of the National Science Foundation, has consisted of a laboratory program at the Francis Bitter National Magnet Lab- oratory at MIT and a pilot investigation at the Hanna Mining Company Research Laboratory. 1 The laboratory tests were conducted using several batch type high gradient separators and a continuous separator with a rotating matrix which was constructed at the beginning of the program. The high field magnets available at F.B.N.M.L. were used for investigations above 10 kG but most of the test work was performed in the range of this field value. Ore samples were contributed by several iron ore companies and consisted of oxidized taconites having goethite and hematite as their principal components.

Jan 1, 1975

By Theodore Ineich

The “BIOMOre” project aims to prove the technical feasibility of indirect in situ bioleaching of sulfide minerals contained in a deep underground deposit, by bringing together the disciplines required to make a success. The underground location in Poland was provided by project partner KGHM inside an operating copper mine. Key components of this project were the design and construction of a pilot plant, and its operation in an underground environment. This project also included a ∼250 t (100 m3) fragmented rock reactor hydraulically connected to the pilot plant. The pilot plant consisted of several tanks and pumps, a fluidised bed ferric iron generating bioreactor containing immobilised acidophilic iron oxidation biomass, and all the required instrumentation and utilities. Before the bioleaching phase could start, the rock reactor had to be flushed continuously firstly with water to remove chloride salts that are corrosive and also harmful for the bacteria used in the bioreactor, and secondly, with sulfuric acid solution to react with the carbonates present in the ore matrix. This paper summarizes the design, construction, commissioning, and operation of the pilot plant.

By M. Abdellatif

Successful demonstration of The Mintek Thermal Magnesium Process (MTMP) was achieved in November 2004 at the pilot-scale, About 30 tons of magnesium producing recipe was smelted in the DC arc furnace over a continuous operation of 8-days, Twenty-two furnace batching-tapping operations were carried out at a feed rate of 525kg/h and a smelting temperature of 1600-1700°C, The MgO content in the produced slag was as low as 6,7%, and averaged 9,2% MgO, resulting in an overall magnesium extraction of 77%, which reached 87% during good operating periods, Magnesium vapour was extracted at a rate of 70-85kg/h and was delivered to the condenser that was operated at 680-720°C, The magnesium was captured in the condenser crucible in a liquid state, allowing its prompt tapping, More than 3500kg of crude metal were produced over 15 on-line metal tapping operations, On average, a condensation efficiency of 85% was achieved during the entire testwork, which peaked at 87% during steady operations, The quality of the crude metal was similar to, if not better than, that of the Magnetherm's crude magnesium, A pre-feasibility study has indicated that the MTMP has the potential for lower capital and operating costs as compared to the electrolytic process, and therefore Mintek and its consortium partners are exploring opportunities for a commercial production facility.

Jan 1, 2006