Search Documents

By Oliver W. Marsden, John O. Marsden

This paper presents the results of a hypothetical case study that evaluates the potential transition of a large copper mining and extraction operation to 90% renewable energy. The case study considers three phases to accomplish such a transition; phase I considers installation of renewable power generation at the site to meet a portion of the current electric power needs, phase II considers conversion of diesel combustion mining equipment to electric equipment, and phase III considers implementation of renewable energy generation coupled with energy storage systems to provide approximately 90% of the total mine site energy requirements. The paper evaluates the results in the context of a range of purchased electric power unit costs ($0.065, $0.100, and $0.135/kWh) as well as various carbon tax scenarios ($0, $5.00, and $37.30/t CO2). While the case study is hypothetical and considers a range of assumptions, it clearly identifies a pathway to potentially economically viable transitions to a renewable energy platform for mining companies. This represents an approach that mining companies can use to help to meet emissions targets, as well as social responsibility and reporting requirements.

Jun 4, 2021

By M. P. Davies

"Risk, the product of probability and consequence, is an integral part of mining. Whether evaluating exploration priorities, determining property acquisition potential, reviewing the components of an operating mine or assessing environmental/closure issues, the concept of minimizing risk is central to economic and technically appropriate decision making.Until recently, risk evaluations have tended toward a strongly mathematical basis. With this previous trend, it was essential to establish precise probability density functions to all assessed components or issues where often little information was available. The combined effect of the seemingly complex analyses with corresponding insufficient data often resulted in either a poorly executed risk evaluation or no evaluation whatsoever; either result not acceptable for optimal decision making. This paper presents a simple and practical procedure to carry out risk assessments for the mining industry. Although simplistic in nature, the power and usefulness of the technique is immense. The basis for the procedure involves combining deterministic assessments (often “gut feel”) with appropriate probabilistic descriptors. The resulting procedure, termed Potential Problem Analyses, or PPA, can be used anywhere an evaluation of risk will assist in optimizing technical and/or economic decisions. As will be shown, a key element of the PPA procedure is the multi-disciplinary input the framework allows which makes the method ideal for a teamwork approach to decision making."

Jan 1, 1997

By Stanley J. Michalek

Good planning is critical to operating a safe and efficient mining operation. As the shallow coal scams become depleted, attention turns toward deeper mineable seams or remnant coal reserves. It is becoming more common to place a mine in a scam that is below or adjacent to existing mine workings. Significant research has been conducted regarding the ground control issues of multiple scam mining. However, safety aspects of the operation may not be fully considered. Safety issues include working below or adjacent to a flooded mine and controlling gas Communication between the active mine and the nearby mine. This paper will discuss the safety issues a mine operator should consider when working under or adjacent to mines that may be flooded with water.

Jan 1, 2000

By N. F. Sather

Results of comprehensive trace element analyses of samples of Illinois #5 and #6 seam coals and the unquenched ashes obtained from gasification of these coals in a Lurgi reactor are reported and discussed. Areas where additional background information is needed for assessment of the environmental impact of trace element emissions from coal gasification are identified.

Jan 1, 1976

By P Aspinall

Safe work Australia (SWA) has a number of proposed amendments to existing Workplace Exposure Standard (WES) values that may dramatically change how mining workplaces using personal gas monitoring instruments will operate. In consultation with leading gas monitor manufacturers and distributors, an assessment of common Australian alarm settings values and analysis of potential frequency of increased alarm likelihoods has been conducted. This assessment explores the relationships between current monitoring practices, using instruments as health and not just safety tools and identify what will be needed to minimise worker ‘alarm fatigue’ and for common tasks to continue safely. This paper provides the necessary information to aid industry and hygienists to be ‘future ready’ given the likely impact that order of magnitude reductions in time weighted average (TWA) values for NO2, SO2, H2S and other common gases will have on current working practices. Reductions to gas alarm values will provide significant challenges to existing work methods and will require, practical application of the pending future values. Improvements and awareness of instrument capabilities by safety and hygiene professionals will better utilise gas monitors real-time data monitoring capacity and no longer be just ‘safe or not-safe’ instruments. The presentation seeks to promote the practical steps required in setting alarms based on risk consequence and likelihood, increase general awareness of the tools and data available in modern instruments and will enable industry professionals to better manage the challenges of any potential future changes.

Apr 16, 2024

By A. J. S. Spearing, T. Kostecki, D. Benton

The use of paste backfill in room-and-pillar coal mines in the United States needs to be fully investigated. This paper discusses a series of physical tests that were conducted to examine the support benefits of theoretical paste backfill regimens in Illinois Basin room-and-pillar coal mines, which necessarily included consideration of weak floor conditions. The series of tests included those simulating strong floor conditions, weak floor conditions, under-confined scenarios, and testing of actual coal-based paste backfill samples. The testing indicated that a paste backfill regimen utilizing a minimum backfill strength of 22 psi at a minimum fill height of 50% of pillar height could significantly increase the longterm stability of coal pillars in the Illinois Basin. Considering typical coal wash plant recoveries, 50% fill would be feasible.

Jan 1, 2014

"Coal seam gas problems can adversely affect the safety and productivity of underground coal mines, leading to fatalities and financial losses. Conventional gas management technologies using ventilation and gas drainage are unable to deal with the high and irregular gas emissions associated with high-production longwall mining. New technologies need to be developed to supplement the traditional gas management techniques to minimize the hazard of coal seam gas. Thin spray-on liners (TSLs) have gained some success for rock surface support since their introduction to the mining industry. Due to their relatively low permeability and appropriate mechanical properties, TSLs also show potential to be used as a gas management tool in underground coal mines.In this paper we review the current gas management challenges and discuss the potential use of TSLs as a gas management tool in underground coal mines. This may involve reducing gas migration into the excavations/roadways, enhancing in-seam gas drainage, and preventing spontaneous combustion. Some potential areas for future research work are identified. IntroductionWhen a coal seam is influenced by mining activities, gas stored inside is liberated into the underground ventilation system. Gas emissions have created serious difficulties for the coal mining industry around the world. Therefore, coal mines have to develop effective strategies to control the gas concentration below the threshold value to meet statutory requirements. Ventilation has been the first solution in gas management for underground coal mining. When the emitted gas cannot be effectively diluted by ventilated air, gas drainage using pre- and/or post-drainage has to be introduced. However, even with ventilation and gas drainage, irregular gas emissions usually increase the gas concentration in roadways and slow down the development rate, thus causing significant economic loss to the coal mining industry (Thakur, 2006). Therefore, new technologies need to be developed to address this issue and mitigate the explosion risk."

Jan 1, 2016

By W. C. Taylor

The present fuel situation indicates that, at least for the next 20 to 30 years, the burning of coal will be a main source of energy. All coal contains sulfur, which is converted to sulfur dioxide during combustion. The concentration of sulfur dioxide (SO2) in the resulting flue gas, for most coals, would exceed the limits established by the Environmental Protection Agency (EPA). Therefore, the sulfur must either be removed from the coal prior to its burning, or be collected from the stack gas before it reaches the atmosphere. There is currently a large amount of research devoted to methods of removing the sulfur from the coal before burning, or during combustion in fluidized beds with materials which trap the sulfur in the solid residue. The commercialization of these processes, however, is not expected in the near future. Flue gas desulfurization appears to be the best near term prospect of fulfilling current air quality control regulations. The lime/limestone wet-scrubbing methods are the most advanced flue gas desulfurization processes and will account for the majority of sulfur removal systems in electric power generation. There are currently at least 23 full-scale systems existing or under construction and 17 of these will use the lime or limestone wet-scrubbing process. (1)

Jan 1, 1974

By P. Lafleur

All indications point to a growing market for thermal coal in Japan as part of the country's current energy policy formulation process. The Ministry of International Trade and Industry forecasts imports of 16 million tons a year in 1985 and 40 million tons in 1990-a twenty-fold and forty-fold increase over the present level. This potential reflects Japan's over-all serious and increasing concern for security of energy supplies and its resultant need to seek alternative sources. Nuclear power will be the main alternative source, but, because it is expected that its development will be slow, imported thermal coal will assume greater importance. Canada, with large resources of all types of coal, could fill a portion of this market. Thermal coal could come from specific thermal coal developments or from metallurgical coal mines, which usually produce a certain amount of coal not amenable to coking, but suitable for power purposes. However, penetration of this Japanese market by Canadian thermal coal will depend on the resolution of a number of problems. On the demand side, siting, environmental aspects, the need for a coal unloading and trans-shipment centre, and the added cost of installing coal-fired stations could be major constraints. Although Canada has ample high-quality resources, any new development tied to the Japanese market will require improvement in prices to cover the high costs associated with transportation, the construction of new mines and the provision of new infrastructure.

Jan 1, 1979

By E. A. Sigworth

Our interest in metallurgical applications for activated carbon was thoroughly aroused when laboratory studies indicated that each dollars worth of carbon could retain as much as four dollars worth of tin. Since then other data was developed suggesting many Potential uses in the metallurgical field it is hoped that, the information presented in this paper may encourage studies by knowledgeable individuals in metallurgical operations. Activated Carbon accomplishes its results by adsorption which involves selective removal of materials from solution by holding the compounds on the carbon surface at the active areas. An example of adsorption is the dyeing of cloth where the dye is selectively held on the cloth surface and the concentration in the dye solution is thereby reduced. Many theories exist on, adsorption, but the predominant factors involved in metallic ion adsorption probably are that adsorption is indirectly proportional to solubility and is benefited by high concentrations acting to squeeze out molecules in smaller amounts.

Jan 1, 1962

By B. S. Old, E. R. Poor

PRODUCING more steel without major capital investment in new plants is one of the most perplexing difficulties which confront the nation's postwar steel industry. The lack of scrap at a reasonable price results in an especially heavy pressure being brought to bear on the pig-iron production facilities which consist of 245 blast furnaces scattered throughout the country but concentrated most heavily in the Pittsburgh-Chicago area. Present demands exceed the total optimum output of these existing blast-furnace plants. Management hesitates to authorize erection of new plants on a scale sufficient to satisfy 'the demand for pig iron for two main reasons: first, extensive building under the present high costs of construction would greatly increase . the over-all capital investment per ton of iron capacity; and, second, the amount of steel necessary for a major construction program would upset the already tight supply-demand situation. The answer to the problem would then seem to be the development and application of a method which would increase the capacity of existing blast furnaces with a minimum of alterations and expense. Experiments consisting of operating a blast furnace at higher-than-normal top pressures, as proposed by Arthur D. Little, Inc., were carried out by the Republic Steel Corp. initially during World War II, and much more extensively during the past twenty months. The results of the Republics trials indicate that pressure blowing is a solution to the problem of increasing pig-iron capacity without necessitating major changes to existing equipment.

Jan 1, 1948

By Walter White

THE measurement of the reading of a thermoelement is the measurement of an electromotive force extraordinarily small compared to those generally used in commercial work. Of the various possible methods of measuring such a quantity, the most advantageous is always a delicate galvanometer. Since a galvanometer measures current, it is necessary to adopt some scheme by which its current reading shall indicate electromotive force. There are two general methods of doing this. One is to use the delicate galvanometer as a "direct reader," that is, to let the electromotive force of the thermoelement furnish the power and produce the current measured. If the resistance is constant the reading will, after a suitable calibration, give the electromotive force of the thermoelement which, by means of a table or of a suitable scale in the galvanometer itself, will FIG. 1.-SIMPLIFIED POTENTIOMETER. POTENTIAL DROP ACROSS THE PART PIN or CIRCUIT OF BULL CELL BALANCES THAT OF THERMOELEMENT TC WHEN GALVANOMETER G READS ZERO. give the temperature. The other method, that of the potentiometer, is to balance the electromotive force of the thermoelement by means of another electromotive force, using the galvanometer to tell when the balance is made. The usual way of getting this other electromotive force is to have a battery, the "bull" cell, send a current through a series of resistances, which 'may in a special case be the resistance of a single wire. The fall of potential along this circuit will then, by Ohm's Law, be proportional to the resistance; the potential difference between any two points, proportional to the resistance between the two points. This is represented in Fig. 1, where M and N are the two points in the circuit AZ of the battery. If M or N, or both, is movable so that the resistance

Jan 9, 1919

T. R. HARRISON, Washington, D. C. (written discussion *).-Ad-vantage will be taken of this occasion to mention briefly a form of double potentiometer which has been used at the Bureau of Standards for about 2 1/2 yr. in calibrating thermocouples. The calibrations referred to are those made by comparison to standard couples. In order to insure equality of temperature between the couples, the junctions are fused together; consideration of fundamental principles will show that this introduces no error. Two separate potentiometers are used, one connected to each thermocouple, and each potentiometer is provided with a reflecting galvanometer. The two spots of light are reflected on to a single scale, the galvanometers being set in such a position that the spots coincide on the scale at a point marked zero when the circuits are open or when the potentiometers are balanced. By setting one potentiometer to a desired value and adjusting the other so that both spots pass across the scale together as the temperature rises or falls, simultaneous readings are obtained. By making observations first with a rising temperature and then with a falling temperature, the rates of rise and fall being approximately equal, and taking the means of the results found, several minor errors such as those clue to differences in the time lags of the two systems, etc., are eliminated or greatly reduced. The differences between the values

Jan 12, 1919

By H. Vendette, N. R. Dando, A. Moras

The thorough analysis of results obtained from different testing campaigns performed on an alumina dry-scrubber pilot installation treating aluminum potline offgases, suggests a clear relationship between the emissions of gaseous fluoride and the fluoride saturation level of the alumina. The integration of this relationship into the development of a new generation of alumina dry scrubber represents an intriguing challenge regarding the design of more efficient air pollution control equipment. An innovative scheme challenging conventional industry practices was proposed. From theoretical simulations, the reduction in fluoride emissions can potentially be reduced by as much as 50% in the summer season. To validate this innovative approach, Solios in partnership with Alcoa Primary Metals, modified one of the Aluminerie de Deschambault's systems by adding new temporary equipment on the operating units and subjecting it to several test campaigns. This article presents the first results obtained in testing this new and innovative approach on alumina dry scrubbers used to capture fluoride emissions coming from aluminum electrolysis potlines.

Jan 1, 2006

WHEN pouring concrete it frequently happens that space prohibits the placing of a mixer at the point, or points, where the concrete is to be used. Usually in such cases recourse is had to some form of pressure chamber, or concrete gun, to blow the mix by compressed air from the mixer to the point of pouring. Recently such a case arose at one of the western mines. The experience obtained there may be of benefit to others, not expert in the means of transporting mixed concrete, when they run up against similar situations. The first stage in pouring in this instance was a vertical drop of 100 ft. from the mixer on one level to the point where horizontal travel began on a lower level. Standard 6-in. pipe with flange joints was used, hung in the shaft space available. A standard 45" bend near the bottom directed the mix, with free discharge, into an air chamber for the horizontal stage of travel. With an air chamber at the mixer and pressure applied to the falling mix in the vertical section, jamming frequently occurred at the turn and the pipe would have to be taken apart for freeing. To obviate this difficulty the mix was poured slowly without the addition of air pressure, when it was found that the mix got through much better.

Jan 1, 1929

By Ian Bell

This paper investigates fragmentation in an aggregate quarry using the fragmentation-energy fan concept. Six blasts were monitored, located one behind the other in the same quarry area. The rock structure was blocky, the water level and the usage of explosives were variable within and between the blasts. The powder factor above grade was between 0.28 and 0.44 kg/m3 (0.47 and 0.74 lb/yd3). Fragmentation of the plant feed was measured using an online digital image analysis system and three belt scales. The oversize material that was not directly fed to the plant after the blast corresponds to 3‒9.3 % of the total. Data from image analysis was used to build the size distribution in the coarse range (fragments above 120 mm), and the passing fractions at 120 and 25 mm (4.72 and 0.98 in) obtained from belt scales data were used in the range 120‒25 mm (4.72 ‒ 0.98 in) . The non-dimensional percentile sizes between 10 and 90 % for each blast are described through power functions of the powder factor above grade; the model coefficients are statistically significant. From them, using the principles of the fragmentation-energy fan and the Swebrec distribution properties, the fragmentation can be expressed in terms of the powder factor by means of five parameters: the fan focus coordinates and the three parameters of a function of the exponents vs. the percentage passing. The model shows a good capability to describe fragmentation.

Jan 1, 2019

By M. A. Steinberg, J. Wulff, R. Kamm

In a previous paper1 from this laboratory, the development of a lead grid method for exploring the distribution of strain and density within metal powder compacts was described. In that work thin lead foil with rectangular holes cut at regular intervals was inserted with the powder fill, the arrangement pressed and then radiographed to permit measurement of the deformation of the lead grid. Densities at each grid element obtained in this manner were plotted as a function of the die dimensions. From such plots it was found that the densest part of a compact pressed from one side (the top) is at the top outer region and the least dense at the bottom outer region of the specimen. The axial density maximum occurs more often nearer the bottom than at the top. As a result of such exploratory measurements, it appeared reasonable to conclude that variations in density could be attributed in the main to die wall friction. Thus compacts of large diameter appeared relatively uniform in density except where the die fill had been uneven. Finally it was found that lubrication of the finely finished die cavity contributed more to magnitude and uniformity of density within the compact than interparticle lubrication. Since publication of the above results, it was found that circular-hole grids could be more accurately made and, when deformed within the powder, more readily measured and analyzed. Much of the former work was repeated and new results which include the effect of lubrication, compact height, pressure, speed of pressing and vacuum pressing are reported in the present paper. Circular-hole Grids and Analyses OF Radiographs Commercial lead sheet 0.008 in. in thickness was used in all the work reported. The 0.0938-in. diam holes were punched in the sheet on 1/8-in. centers to an accuracy of 0.001 in. The finished grid used contained eight or more holes in a row and from I to 24 rows. The lead sheet was clamped between two pairs of brass strips bolted to a small milling machine table which was itself bolted to a bench in correct position near a vise which held the punch. Travel of the lead grid in two dimensions was controlled by two steel lead screws calibrated in 0.001-in. divisions. A stripper plate was used on the punch to avoid distortion of the lead foil. A high carbon-high chromium (chrocar) one-piece steel die was used throughout the work. The die cavity was 1.125 in. in diam and the clearance between plungers and die wall was 0.001 in. The die was also used for pressing from both ends with two long plungers. Finally, lapping of die and plungers gave a surface whose rms value On an Abbot profilometer was 5 micro-in. The die walls and plungers were, except where otherwise noted, lubricated with a stearic acid suspension in benzene. This was put on in multiple layers and allowed to dry before filling the die.

Jan 1, 1949

By W. Rostoker

The process of diffusion alloying of mixed powders offers attractive possibilities both commercially and experimentally. It avoids the fabrication difficulties arising from high alloy contents. Indeed, the process is facilitated by larger alloy additions. The direct formation of the part or test piece and the opportunlity to perform machining operations under more favorable conditions are of no small importance. However, it is necessary to make only brief mention of the interesting features. As yet there have been few attempts to study this process in detail and to carry it to completion, if such is possible. It was intended not only to measure the intermediate and optimum magnetic properties of sintered alloys but to use magnetic testing itself as a means of following the progress of alloying under various condi-tions. Having established that alloys could be successfully synthesized by this tech. nique, the opportunity was taken to study the magnetic properties of several alloys of iron and silicon which had hitherto been too difficult to prepare in suitable test piece form. While avoiding some of the difficulties inherent in the fabrication of alloys by orthodox methods, the diffusion alloying process introduces a few of its own. The first of these is the evaluation of the approach to homogenization. In recent years some notable contributions have been made to this question, but considerable uncertainty remains in its definition and evaluation. This work has concerned itself with further study of this problem and it is hoped that more light has been shed on it. The second of these difficulties arises from the presence of porosity. It is inevitable that in the consolidation of a loose bulk of powder, there should remain some voids unless extremely high pressures are repeatedly applied. It was therefore of importance to investigate their effect on magnetic properties. Recently this effect has been studied and certain predictions made of its behavior. It is believed that the experimental results presented here provide a sound substantiation of the theoretical treatment. The attempt has been made to synthesize five alloys of the iron-silicon system and three each of the iron-nickel and iron-cobalt systems. A series of experiments was also conducted on some of these alloys to test their susceptibility to heat treatment. Some unfortunate experiences have provided opportunity to report data on the deleterious effects of nitrogen on magnetic properties when present as a a in protective atmospheres. MateRIALS, PREPARATION OF SAMPLES and Testing The purest materials available were em. ployed for this work. A specially purified,

Jan 1, 1949

By D. P. Bishop, G. J. Kipouros, R. L. Hexemer Jr., I. W. Donaldson, W. F. Caley

Aluminum powder metallurgy (APM) is an advanced metal forming technology frequently employed to fabricate complex structural components in a near-net-shape fashion. Exhibiting nearly 100% material utilization, APM continues to rise in popularity. Recent research initiatives in this field have emphasized the development and processing of advanced 2xxx and 7xxx series alloys. In particular, APM equivalents to wrought 7075 and 2024 have been sought. An overview of work completed in this area is presented. Included are data on the various production stages (powder compaction, sintering, forging, and heat treatment) as well as the microstructure and mechanical properties of the finished products.

Jan 1, 2010

By L. Alan Weakly

The Powder River Basin of northeastern Wyoming and southcentral Montana contains the largest strip minable reserve of compliance coal (0.27 kg or 0.6 or less Ibs of sulfur per million Btu) in the United States. In mining parlance, it is the mother lode. Wyoming's portion of the Basin is called the Southern Powder River Basin (SPRB). It has been the nation's top coal producer for the past nine years. And based on 1997 production statistics and estimated strippable compliance coal reserves, Wyoming should remain the nation's top producer for the next 51 plus years. In August 1994, ME featured 10 articles that covered all aspects of coal production in the SPRB. In this issue, five authors update the 1994 articles and provide a pre- diction of what the Basin will look like at the turn of the century. In addition to this article, the titles and authors of the other five articles include: ? "Geology of Wyoming's Powder River Basin coal field," by Gary B. Glass and Robert M. Lyman. ? "Coal quality challenges in the Powder River Basin," by Sharon Roness, Richard A. Turpin and Robert A. Young. ? "Markets for Southern Powder River Basin coal," by , Patti J. Best and Patrick W. Wright. ? "Evolution of mining equipment in the Powder River Basin," by Kenneth R. Miller and James L. Long. ? "Hauling coal into the 21st century," by Dave Willis and Will Cunningham.

Jan 1, 1998