Search Documents

"The Butte, Anaconda & Pacific railway extends from Butte to Anaconda. The electrification comprises 30 miles of main line single track, and includes sidings, yard and smelter tracks. When complete the electrified trackage will total about 90 miles on a single track basis.The traffic conditions are unusually severe as they consist principally of hauling copper ore from the Butte mines to the smelters at Anaconda, as well as hauling all the mine supplies, lumber, etc., in both directions; this traffic amounts to approximately 5,000,000 tons of freight per year. The maximum grade against the load is .3 per cent and the maximum train consists of 50 loaded steel ore cars, weighing 3,400 tons. .The locomotive units, two of which will be used for freight trains, weigh approximately 80 tons each. In addition to the freight business, there will be a certain amount of passenger traffic.The power for operating the Butte, Anaconda & Pacific railway is generated by, the Great Falls Power company, and is transmitted to the sub-stations at 100,000 volts. The synchronous motors are supplied with power at a potential of 2,300 volts, 60 cycles, 3-phase. Voltage regulators are installed in each sub¬station to secure the benefit of synchronous condenser effect of the motors.The passenger and freight locomotives are exactly similar, with the exception of the gearing.The roller pantograph mounted on the top of the cab is operated by air from the engineers position.The adoption of the 2,400-volt apparatus for so important a system, where the conditions of operation are so severe, is interesting of itself, as indicating the trend that future electrifications of importance may follow. A trolley potential of 2,400 volts was only adopted after a thorough investigation of other systems already in operation."

Jan 1, 1913

By T Baumgartl, B Richards

Covers on waste rock and tailings remain the primary choice for closure planning where the purpose is to create an environment where water ingress into reactive material can be controlled and/or prevented. In semi-arid and arid environments, dry cover systems are the preferred option with the design intention to absorb rainfall and to prevent deep drainage. Although the average amount of rain typical for semi-arid environments is relatively low and evaporative demand is high, the seasonal and annual distribution may vary greatly. Rocky substrates are often the only choice for the construction of covers due to economic constraints or availability of suitable materials. While the water holding capacity may be suitable for the application of a dry cover design in arid and semi-arid climates, some of these covers bear the risk of preferential water flow when rain events are intensive or occurring at high frequency. The objective of this presentation is to demonstrate the occurrence of preferential flow through rock containing dry cover systems. A regional classification for the applicability of dry covers is attempted to delineate those regions of Australia where the characteristic of the rainfall pattern increases the risk of failure for dry cover designs. CITATION:Baumgartl, T and Richards, B, 2016. Rainfall patterns rather than climate classification control cover design for closure, in Proceedings Life-of-Mine 2016 Conference, pp 89–92 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By S. A. Lorentz, Y. Xu, C. Theron

The failure of tailings storage facilities (TSFs) results in the discharge of significant quantities of hazardous waste material into the natural environment. Research studies relating to slope instability have identified physical mechanisms such as rainfall-induced erosion, liquefaction, and shear failure as the main triggers. The generation of transient pressure waves and the mobilization of pre-event water in the unsaturated zone have been found to trigger shallow landslides in natural hillslopes. In this paper we review these physical mechanisms, known as groundwater ridging (GWR) and the Lisse effect (LE), from other studies. Previous researchers have explained both these phenomena through field and laboratory observations, numerical modelling, as well as conceptual discussions. These case studies demonstrate the impact of rainfall characteristics on the generation of transient pressure waves that rapidly increase the phreatic surface and change pore water suction. Reference is also made to the influence and behaviour of physical porous medium characteristics on the establishment of a continuous water phase that facilitates the transmission of an induced pressure head. However, previous studies fail to recognize the possibility that the pressure increase in pre-event water through pore air propagation could cause slope instability in tailings dams. The authors suggest that the physical properties and hydraulic behaviour of unsaturated porous tailings media make it susceptible to GWR and the LE, resulting in the creation of a potential failure plane.

Feb 2, 2022

By A Penney, M J. Pascoe, R M. Stephenson

The empirical McCracken and Stacey stability and risk assessment method has been in use for more than 20 years to assess geotechnical stability issues for raise bored shafts. The methodology has been applied with various levels of success. Increasingly, trends in mining and civil tunnelling have been towards larger diameter, single pass, raise bored shafts to rapidly provide means of ventilation, material movement (ore passes), or emergency egress. Identifying and assessing potentially problematic zones before raise boring commences can allow for appropriate risk-based decisions on construction, or to investigate alternative solutions. The implementation of a proactive solution to raising through an identified weak zone is preferred to the application of an engineered solution to an area subjected to substantial instability or failure. Methods for investigating potentially problematic areas are discussed in this paper based on AMC’s benchmarking data. Proactive investigation programmes resulting from these investigations are also discussed. Previous publications discussing the benchmarking data have concentrated on Australian case studies. Increased efforts and recent updates have been made to expand the database to include international case studies. This has provided further refinement of lower bound ‘raise bore rock quality index’ (QR) values, and various rock mass parameters for stability assessments. CITATION:Penney, A, Stephenson, R M and Pascoe, M J, 2018. Raise bore stability and risk assessment empirical database update, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 434–445 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By William T. Folwell

INTRODUCTION - CURRENT RAISE BORING PRACTICES Raise boring is a comparatively new tool to the underground mining and construction industries. Underground raise boring, in this country, had its beginning in the early 1960's, in the iron mines of Michigan. These first raises were bored 40 in. and 48 in. in diameter with maximum lengths of approximately 200 ft. Since the late "sixties", the raise boring machine has been accepted by the mining industry as an important machine to increase excavation rates, provide adequate ventilation airways, improve safety, and reduce costs, to name a few of the benefits. The construction industry is now accepting raise boring techniques for hydro-electric power projects, water supply projects, tunnel projects, waste water projects, etc. Raise drills are now capable of boring raises to diameters as much as 12 ft, in the softer rock types. Raise lengths range from 200 ft to as long as 1700 ft. Bored raises, in general, are bored at dip angles ranging from 45º to 90º, depending on the requirement of the raise. The general practice is to drill the pilot hole down to an opening below and up ream the pilot hole to the required diameter. The pilot hole (9-7/8", 9", 11", or 12-1/4" diameter) is generally drilled with compressed air to remove the cuttings. In the event that ground water is encountered and removal of cuttings is impeded, a foaming agent is added to assist in lifting the cuttings. When excessive water is encountered, water is used as the circulation medium and the cuttings are removed by pumping. During the reaming cycle, the cuttings fall by gravity and are removed from the bottom of the raise by conventional methods.

Jan 1, 1997

By John G. Ayttes

"The following is a review of the advance of raise boring and its current position. The viewpoint presented is that the mining industry, through its worldwide acceptance of raise boring, has acknowledged the success of the method in general. Acceptance, however, does not imply complete satisfaction with either the equipment or current operating costs. Therefore, a brief review of how boring costs are being r educed is presented, citing examples. Recent raise borer applications of special interest are presented to show adaptability of current equipment, and some special projects in the planning stage are highlighted."

Jan 1, 1972

By W. J. Taylor, T. D. Parris

"Over 90,000 feet of raise have been bored at International Nickel underground mining operations throughout the Sudbury District since the advent of raise boring in the early part of July, 1964. With a total of 10 raise borers on hand at this time, techniques have improved steadily since introduction at INCO mines. The first unit, designed for use in rock of low compressive strength, had to be modified and redesigned to cope with Sudbury Area Precambrian rock. As equipment and boring techniques improved, a specially designed machine for larger holes was developed and is now in use. More powerful units, with a thrust capacity of up to 750,000 pounds, are under investigation. Raises have been bored up to 84-inch diameter, and the changeover to 5- and 6-foot flat reaming heads with improved cutter design has increased performance substantially. As a result, 5-foot-diameter raises have been completed to a length of 750 feet and 6- and 7-foot raises to over 500 feet. Reference is also made to the drilling of over 23,000 feet of drainage and sand-fill holes, ranging up to 7% inches in diameter, with smaller underground rotary drill equipment.Finally, a look into the future indicates the need for further improvements in equipment design to permit economic boring of 7- to 8-foot-diameter raises in Sudbury Area ground types."

Jan 1, 1972

By Lyle F. Smith

With the demand for larger diameter raises under all ground conditions and the increasing price of drill rods and operating costs, it was evident that there was a need for a raise borer with a variable-speed drive and fast-response torque limiting control. The raise boring machine described in this paper was developed after several years of market research and discussions with mine operators and construction contractors. This paper discusses the Ingersoll-Rand raise borers with the solid-state controlled DC motor drives. These machines have gained wide acceptance in the five-year period since being placed in operation and are designed to accommodate the range of raise diameters and lengths most required today.

Jan 1, 1978

By Hans Svensson

INTRODUCTION The Alimak method of raising (Fig. 1) was intro¬duced in 1957. Because of its flexibility, economy, and speed, it soon became the most used system of raising in the world. With the same unit, raises of various areas, inclinations, and lengths can be driven. Air-motor¬-driven raise climbers normally are used in mines with short raises (Fig. 2). For longer raises electric or diesel-¬hydraulic drives are used. The Alimak raise climber is designed entirely in ac¬cordance with the instructions of the Swedish Board of Industrial Safety (Arbetarskyddsstyrelsen). There are good margins of safety concerning the breaking strength of the material and the raise climber comprises safety devices and features that practically eliminate the risks of accidents. The drive gear of air-driven climbers is equipped with an air-operated brake which is automatically activated when air for the motors is shut off. There is a safety device which activates automatically at overspeed and a speed-regulated brake for descent by gravity, by which the raise climber can be taken down to the bottom of the raise in case of cutoff of the air supply. The raise climber climbs along a pin rack welded to a guide rail which also comprises pipes for air and water. The guide. rail can be extended by using 1- or 2-m (3.2¬or 6.4-ft) sections as the driving progresses. Each guide rail section is bolted to the rock wall by special expan¬sion bolts of Alimak design. Men ride up to the face in the cage, traveling com¬fortably and easily while material is transported on the platform. There is no dangerous climbing up ladders. The men are well protected during ascent and arrive in good condition at the face. The greatest advantages of raise climber systems are flexibility and versatility. The equipment provides a comfortable working position in vertical as well as in¬clined raises of any area and length. The direction may

Jan 1, 1982

By B. Burger, T. Bester, S. Deonarain, L. S. Schultz

"This paper details the process followed to raise drill and equip a 6.1 metre diameter vertical service shaft at Glencore’s Mindola Deeps project in Kitwe, Copperbelt Province, Zambia. The project scope comprises a shaft collar, bulk air intake, a pre-sink to -90 metres and raise drilling the shaft from surface to a final depth of 1,892 metres underground, in four separate lifts of approximately 475 metres each. Equipping of the shaft steelwork, headframe erection and commissioning the shaft for hoisting. In addition, the scope included the development of a decline down from 5430’ level underground to the new shaft position on 6205’ level. This paper will provide some insight into the successes and challenges encountered during execution of the shaft works to date and provide some learnings for future projects of a similar nature. INTRODUCTION The Mindola Mine is situated to the west of the city of Kitwe in the Copperbelt Province of the Republic of Zambia (Figure 1). The mine is owned and operated by Mopani Copper Mines Plc (MCM), whose shareholders are Glencore AG (73.1%), First Quantum (17.9%) and ZCCM Holdings Plc (10%).Productivity at the Mindola mine has been adversely affected because of significant ventilation and ore re-handling challenges, which are caused by the dilapidated infrastructure, and design of the existing vertical and sub vertical shaft system. In the circumstances, it was apparent that it was necessary to sink a new vertical shaft that would increase the volume of fresh air down the mine, improving the underground working environment and the current hoisting restrictions, resulting in an increase in productivity and efficiency. Because there were two existing levels ideally situated and perpendicular to one another and because a third level was in close proximity to that perpendicular and because the mine required a ramp down to shaft bottom in any event, consideration was given to raise drilling the shaft as opposed to using conventional blind sinking methodologies."

Jan 1, 2019

By Lok W. Home

INTRODUCTION Today, raise drilling (boring) has become the stan¬dard method of raising throughout the Western world. It is estimated that the majority of raise footage com¬pleted in 1977 was accomplished by the raise drilling method. Extensive replacement of the drill and shoot system by mechanized raise drilling has occurred be¬cause users have recognized one or more of the follow¬ing advantages. In a direct cost per meter comparison, mechanized raise drilling is economically more attractive than drilling and shooting. Mechanized raise drilling offers improved personnel safety over the drilling and shooting method. Mechanized raise drilling is a faster and more predictable method for excavation than is drilling and shooting. The raise cost per unit of length becomes less as the raise length increases, offering greater flexibility in the overall design of mines. Mechanized raise drilling provides a substantial reduction in labor requirements. 6) Mechanized raise drilling improves the working environment. 7) Mechanized raise drilling improves the rock in¬tegrity of round, unblasted raises. Increasing acceptance of the raise drilling technique is enhanced by continuing equipment development. Today, a wide range of machines and capabilities is available, machine drive systems have been improved, reliability has been increased, and cutter technology is being improved quite rapidly. Table 1 lists the four major manufacturers of raise drilling machines, cutters, and reamers, together with the approximate number of machines that each company had in operation at the end of 1977. Although Reed and Smith are major suppliers of reamers and cutters, they do not manufacture the drilling machines. Four or five other relatively minor suppliers have built machines, reamers, and cutters for raise drilling, but they did not have a substantial num¬ber of machines in the field at the end of 1977. MACHINES FOR MECHANIZED RAISE DRILLING There are three principal arrangements for making machine-bored raises. They include the use of standard raise drills, reversible raise drills, and blind-hole or box¬hole raise drills. Standard Raise Drills The standard raise drilling machine is set up on one mine level or on the surface, and a pilot hole is drilled from that level or surface to a level below. When the pilot hole has been drilled, the raise then is reamed back from the lower level to the upper level or the surface. This arrangement is illustrated in Fig. 1. Reversible Raise Drills The reversible raise drilling machine is set up on a lower level of the mine, and a pilot hole is drilled up¬ward to a higher level. The raise then is reamed back from the upper level to the lower level. This arrange¬ment is illustrated in Fig. 2. The machines used for this type of raise drilling normally are capable of being used as standard raise drills. Blind-Hole or Boxhole Raise Drills The blind-hole or boxhole raise drilling machine is set up on a lower level of the mine, and a full diameter raise is bored to a higher level without the use of a pilot hole. This type of machine is illustrated in Fig. 3. Drill Recommendations If access to upper and lower mine levels is equal, the standard raise drill should be used. The complexity of the equipment and associated handling procedures for boxhole drilling far outweigh any mechanical advantage or reduction in the number of operations, provided that access to an upper level is available. If there is good access to a lower level but only limited access to an upper level, the use of a reversible raise drill should be considered. If there is no access to an upper level, a blind-hole or boxhole raise drill is the only practical mechanized system. MACHINE SELECTION There are six major considerations in selecting a machine for raise drilling. These include operating range, cutter loading, machine structure and main¬tenance, drill string configuration, drive system, and automated controls. Operating Range As shown in Table 2 and Figs. 4 through 6, raise drilling machines are available for a wide range of hole sizes. Standard raise drill ratings range from raises of 0.9 m (3 ft) diam and 120 m (400 ft) length up to raises of 3.5 m (12 ft) diam and 900 m (3000 ft) length. Boxhole raise drilling machines are available for raises ranging from 0.9 m (3 ft) to 2 m (6 ft) diam with lengths up to 90 m (300 ft). Table 2 lists, among other criteria, the torque and thrust of typical machines; torque and thrust are the main criteria for analyzing the capacity of a machine. The raise sizes shown in Table 2 assume a condition of medium hard to hard rock formations and optimum cutter loading. The recommended raise size for a given machine can be exceeded when raising softer rock formations or when the operator is willing to accept a lower level of performance; the performance is related directly to the 1093

Jan 1, 1982

By M Andrew, D McTiffen, M Adams

A major Ventilation Upgrade Project commenced at the Fosterville Gold Mine (FGM) in 2017 to service the ongoing ventilation requirements of the underground mining operation. The project consists of three large diameter ventilation raises totalling 1100 metres, and new axial primary ventilation fans to upgrade the mine ventilation system. With a mining depth of 1200 metres and a thermal gradient of approximately 2.7 °C per 100 metres of depth, the completion of the Ventilation Upgrade Project is key to the ongoing success at FGM. The Ventilation Upgrade Project will allow continued mining, including high-grade gold deposits, lower in the mine where heat is increasing. Figure 1 below illustrates the underground workings at FGM, and provides a general view of the ventilation upgrade works to establish the new exhaust system from the lower workings to surface. Whilst raisebore pilot drilling the H4760 Return Air Rise (RAR) from surface to 395 metres, the raisebore drill string became stuck in the raisebore pilot hole at approximately 300 metres down hole, presenting a significant technical problem and delays to the project. This Case Study provides an overview of the recovery process undertaken at FGM including the recovery of the stuck drill string. The value of the stuck in-hole equipment, the investment in the shaft site preparation, the collar stabilisation, the underground development to the base of the ventilation raise, the surface footprint prepared for the Primary Fans construction and the limited available space on the site were all motivations to recover the raisebore drill sting and ultimately recover the ventilation raise location. More importantly, the long lead-time required should a new shaft location be the final solution, and the delay this would incur to the ventilation upgrade was unacceptable. Recovery of the drill string was not possible using the capability of the Contractor’s Raise Drill. An alternative method for freeing the drill string was required. A significant amount of engagement with industry was undertaken to seek out potential solutions and draw from the experience of others. All methodologies available were considered and assessed. Ultimately, after several attempts at freeing the raisebore drill string using various methodologies, Adams Drillers and Clear Cut Interventions were engaged to provide a turnkey recovery solution.

Mar 15, 2021

By Jos. Kalbhenn

PART of the plan of re-allocation evolved by the engineers of the Dominion Steel and Coal Corporation in 1932 to retard the rapid advance of the submarine workings seawards was the opening of Dominion No. 20 Colliery, in the Harbour seam, by a pair of cross-measure tunnels from the workings of an older mine working the Phelan seam, which lies 430 feet below the Harbour seam. The tunnels, 8 ft. by 13 ft. in size, were started away from the old workings of Dominion No. 2 at a point 1.5 miles beyond the shore line and were driven on a rising grade of 1 per cent for a distance of 5,335 feet, tapping the Harbour seam at a point 2 ¼ miles off-shore. For transportation and ventilation, shafts and roadways already existing in the Phelan seam were made use of during the stages of development and up to the present time. One of the two tunnels served as a main haulage road and an intake airway, and the other as a return airway and travelling road. However, as the workings of this new colliery expanded, the need for additional airways arose as was anticipated when the plans for the development were formulated. To meet this need, work was started on October 1st, 1942, to establish a new opening between Nos. 2 and 20 Collieries in the form of a vertical shaft to provide a passageway for the ventilating air current of some 250,000 cubic feet per minute on its return to the upcast shafts in No. 2 Colliery, thus making both tunnels available for intake airways. In the interest of safety, speed, and economy, the shaft was raised from the Phelan to the Harbour seam. It is 20 ft. by 12 ft. in size and, with the exception of three timbered compartments across the narrow end, is untimbered. One of the three timbered compartments housed the ventilating tubing and pipe lines, the centre one served as a cage-way for hoisting men and material during the operation of raising, and the third one contained a ladder way. The rest of the shaft was filled with debris during the period of shaft raising.

Jan 1, 1944

By Jos. Kalbhenn

MR. G. G. BOWSER: Mr. Kalbhenn's paper is an excellent one and is a concise description of a very interesting piece of work. It is well known that a great deal of preliminary study was given to this job before the final plans were made. It is due to this thorough preparation .chat the work progressed so satisfactorily, smoothly, and safely. The ideas carried out in the construction of the hardwood pack, timbered compartment, inclined raise, loading chute, and steel-boomed room, all contributed to a successful conclusion of the work. The extra care in being certain that the compartment shafts were well timbered was especially necessary on account of the difficult blasting conditions. In other words, the foundations .of this job were well and truly laid. The blasting in this work was very difficult due to the nature of the Strata. Working under an ever precarious roof condition and completing .this job with only two lost-time accidents is a record of which to be proud. The shaft men engaged on this work are also due for praise. I regret I did not visit this work while it was in progress. It was not in lack of interest. This, however, more or less proves that the blasting end .of this job went along with practically no trouble. I have seen the nature of the rock, as I made several visits to the tunnels while they were being put through from the Phalen to the Harbour seam. According to figures in Mr. Kalbhenn's paper, the explosives consumption works out to 1.61 pounds per cubic yard of rock in the solid, or 0.8 pounds per ton. The explosives consumption in the tunnels ran from 2.86 to 3.46 pounds per cubic yard or an average of 1.58 pounds per ton of rock. Of course, the rock in the shaft was blasted in the most economical way possible, as far as powder costs are concerned, as the face advanced at close -wright angles to the strata and gravity was acting with the explosive. The tunnels were driven nearly 'end on' the strata and bottom holes had to be lifted, and I believe there was some re-drilling of ribs left in the floor. I would like to congratulate Mr. Kalbhenn on his very fine paper.

Jan 1, 1944

By John C. Wangaard

A method of raising by use of a cage has been used with considerable success at the Cary Mine, Hurley, Wisconsin, on the Gogebic Range. The Cary Mine is owned by the Odanah Iron Company, Pickands, Mather and Company, Managers. This method is known to have been used previously at Tennessee Copper and probably in other districts. The Cary Mine was engaged in deepening the main shaft from the 34th to the 37th level. To accomplish this, and to facilitate development, a ventilation shaft 930 feet north of the main shaft was sunk from the 34th to the 37th level and crosscuts were driven on the 35th, 36th and 37th levels to the main shaft location, These levels are at 200 foot verticalintervals. All of this work was done in granite and the majority of the workings were not timbered. The next step was to get a raise through from the 37th to the 36th level, and from the 36th to the 35th level, which would later be stripped to full shaft size. Several methods of raising were considered including double-compartment cribbed and two single raises interconnected at regular intervals, but the cage method was chosen as it appeared to be a safe and efficient operation. The method in general consists in the use of a drill hole between levels through which to pass a hoisting rope to raise and lower a light cage.

Jan 1, 1958

By Richard DePew, Robert J. Auber

The Westerly Storage Tunnel is a 25-foot diameter segmentally lined storage tunnel that is a major component of the Northeast Ohio Regional Sewer District's Project Clean Lake that is designed to capture 39 million gallons of untreated CSO overflows from entering Lake Erie. During the final stages of the project completion, a large-scale rock fallout incident occurred during the final lining installation operations at the down-stream end of the tunnel that extended beyond the designed primary support system. This paper outlines the level of coordination and collaboration between the Owner, Designer and Contractor to remediate the situation safely, quickly and effectively.

Jun 23, 2024

By P Wood, S Leveritt

This paper will introduce some innovative strategies for simulator training that are intended to improve the level of safety and operational performance of heavy equipment operators. The key strategy is to design simulator training to deliver improved work performance outcomes. This strategy is underpinned by a process for engaging workers in knowledge discovery and transfer that has been developed as an outcome of an Australian Coal Association Research Program (ACARP) funded project conducted at open cut coal mines in Australia. The process is expected to deliver improvements in the safety and operational performance of heavy equipment operators by informing training content about how experienced operators manage unexpected situations around the site. Tapping into the tacit knowledge that experienced operators gather over time can provide site specific and timely information about situational cues used to manage the unexpected. This type of information complements basic skills training by helping the trainee understand the operational context in which the acquired skills will be applied. Inexperienced operators have traditionally gained experience through their own actions, observing the actions of others and by taking the advice of mentors who have æbeen there, done thatÆ and developed operational decision making skills for safe and productive work performance. Leadership and mentoring techniques that contribute to effective knowledge delivery will also be discussed.Other simulator training strategies include refresher training, change management, emergency response training and testing the usability of new equipment and technologies prior to their introduction on-site. A key challenge ahead for the resources sector is the development of knowledge elicitation techniques that suit the operational workforce. A challenge for simulation and modelling professionals is to develop and refine techniques that support cost-effective customisation and regular updates of simulator scenarios.CITATION:Leveritt, S and Wood, P, 2012. Raising the simulator training bar - Strategies for improved work performance and effective utilisation of site-based simulators, in Proceedings Eighth Open Pit OperatorsÆ Conference , pp 65-70 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 18, 2012

By Olli Haavisto, Heikki Häkkänen, Tommi Kauppinen, Navid Khajehzadeh

Raman analysis is a well-established method for finding the abundant minerals in an ore sample. In this study, Raman spectroscopy is tested as a method for rapid and contactless on-line mineral analysis. Rapidness might enable on-site analysis of rock drillcore, which in turn would lead to more cost-efficient solutions in mineral exploration. This paper discusses the use of Raman analysis to identify minerals and to measure their concentration. The sample set under study consists of rock drillcore collected from Agnico-Eagle Kittilä Mine, Finland. Selected parts of the sample set are measured by Raman spectroscopy and the minerals are identified using reference spectra from a public source. Moreover, the direct measurement of concentration of different minerals with the help of Non-negative least squares (NNLS) optimisation algorithm is considered. The optimisation algorithm was constructed to form a linear combination of reference spectra which best represent the measured spectrum, or an average of measured spectra, from an ore sample. The results show that NNLS can identify abundant minerals in a given sample. Also through this method of analysis the results of a traditional point-count method can be expanded: It was observed that, due to grain size, multiple minerals consistently appear in the spectra measured over an area, which means that point-count method is not a proper way to interpret the spectra. This can be seen as a new result, as formerly the discussion has attended to other methods.

Jan 1, 2014

By E R. Ramanaidou

The value of Raman spectroscopy to undertake mineral and chemical characterisation of iron ores was assessed by applying the technique to representative samples of banded iron-formations (BIF) and a BIF-derived, martite-goethite ore. The common iron oxides haematite, magnetite and goethite as well as gangue minerals such as quartz and carbonates all show distinct Raman spectra that enables these phases to be easily detected and mapped in situ for either samples prepared as polished blocks or unprepared material. Raman spectroscopy also offers the potential of in situ chemical characterisation. Shifts in the excitation bands of carbonate detected in BIF were related to the Mg content of Fe-carbonate and confirmed the first world-wide occurrence of a high Mg-bearing siderite (pistomesite) in BIF.The discriminatory power of Raman spectroscopy coupled with the potential of the technique to offer large-scale (volumetric) characterisation of iron ore will be of great value not only to the existing BID and CID ore types, but also to the newly emerging magnetite iron deposits (MID).

Jul 11, 2011

By Gregory A. Hope, Kym Watling, Matthew I. Jeffrey, Ronald Woods

Surface enhanced Raman Spectroscopy carried out in real time has been applied to identify surface species formed during gold leaching in chloride and thiosulfate media. Chloride ion is adsorbed prior to the gold dissolution potential, but its coverage is significantly diminished at the beginning of leaching. A gold chloride band is again observed when dissolution is rapid, together with bands characteristic of AuC14- ions in solution. With thiosulfate, a thin gold sulfide layer is formed slowly in the potential region where leaching occurs. At higher potentials, thiosulfate is oxidized to sulfur and sulfate, both products being identified by Raman spectroscopy.

Jan 1, 2005