Search Documents

By William R. Groseclose, Cecil E. Tackett

Since 1965 when the first mole was used on Bureau work, the Bureau of Reclamation has completed 17 tunnels of over 5,000 feet in length. The longest was 12.8 miles. Total length of the 17 tunnels was 376,207 feet, or over 71 miles. The finished diameter varied from 7 feet 0 inch to 18 feet 0 inch with 82 percent (58 miles) being less than 12 feet 0 inch in diameter when lined. All of these tunnels except one are gravity flow, water conveyance tunnels with relatively flat gradient. One is a low-head pressure tunnel. All were constructed by contracts resulting from fixed-price bids. Starting in 1964 the Bureau of Reclamation initiated the practice of giving several options in the specifications on methods of tunnel excavation. Since that time, construction work has been completed on 17 tunnels. Of this number, 11 were mole excavated and 6 were excavated by conventional drill and blast methods. In general, there has been 2 feet of mole excavation for every 1 foot of drill and blast. Cost comparisons are based on only 13 tunnels because the Bureau has 4 recently completed tunnels that have pending claims; therefore, final cost data are not available. Some definite trends show from the data available; however, the number of completed tunnels in some categories is so small the results cannot really be considered a trend. As more data become available, the indications will become more reliable. The information is presented to indicate general trends and comparisons and cannot be meaningfully used for a one-on-one comparison because of individual tunnel differences not considered.

Jan 1, 1974

By M W Kearns

The ERA - Ranger Mine ore processing operation consists of a sulphuric acid leach followed by counter current decantation and solvent extraction circuits. The most expensive unit processing operation at Ranger is the sulphuric acid leach. In 1992 and 1993 changes were made to the operation of the leach circuit. These changes have reduced power and reagent consumption in leach by 30 per cent and 20 per cent respectively with minimal effect on extraction efficiency. The first change was to operate the leach circuits at higher pHs than previously attempted. In addition a cap was placed on the amount of acid added to the leach circuit. Secondly, an on-line pH measurement system was installed and has reduced the variation with time of the leach circuit pHs. Finally, the number of leach vessels used was reduced from ten to seven. This action was undertaken after an examination of the uranium profile and the residence time in the leach circuit from previous years. This paper examines the above changes and assesses their effectiveness on plant performance and costs.

Jan 1, 1994

By W. G. Hatch

Introduction In November, 1927, a paper was presented at the Annual Meeting of the British Columbia Division by H. A. Pearse(l), in which he described the milling practice at Britannia and set forth the metallurgical results which were being obtained at that time. In the intervening four years, various changes and additions have been made in equipment and practice, which have resulted in marked improvements in efficiency and costs. These changes and their effects are discussed in the present paper. During the past few years two major changes have been made in plant equipment. The first of these was the. elimination of an intermediate crushing stage by discarding two gyratory crushers in favour of two Symons cone crushers. The latter installation-now effects in one stage a greater reduction than was formerly accomplished in two, that is, by the gyratories together with a set of rolls. The second important change in equipment took place when the original M.S. flotation machines were replaced by six Forrester pneumatic machines, so that now the flotation department consists entirely of machines of this type. A number of minor changes and some further additions to equipment have also been effective in raising plant capacity and concentrate grade, while making noticeable reductions in tailing losses and costs of ore treatment.

Jan 1, 1932

By A. Dave Mackintosh

Historical closure data has provided a description of the stress distribution patterns occurring around mine openings and enabled the development of a time ? distance plot predicting the location of the stress peak and its migration away from mine openings with time. Data collected from active mining areas during the 1970?s and 1980?s indicated the peak appeared to stabilize approximately 135m (450 ft.) from openings after four years. The region of high load and accompanying poor ground conditions in which the peak was centred was spread over approximately 45m (150 ft.) to 60m (200 ft.). Recent data from new development headings cut adjacent to 25 year old extraction areas suggests load transfer takes place over a much greater distance and time frame than predicted.

May 1, 2001

By J. D. McKay

Flotation columns have been readily accepted for use in most sulfide flotation plants; however, recently columns are being used in many other areas. Recent improvements in design methodologies have overcome many operating problems and led to improvements in metallurgy. In addition, physical improvements in column design have simplified their operation while leading to better control. The Turbo-Air External Bubble Generator has provided a method for bubble size control and variation in air holdup and carrying capacity. These have enabled commercial operations to improve grades and recoveries by optimizing performance.

Jan 1, 1990

By George J. Skoronski

The economics of pellet plant operation, in terms of fuel and power consumption, flexibility in the selection of the cheapest fuel source, system availability, maintenance costs, and the simplicity of process design, contribute to the determination of building and profitably operating a pellet plant. Design innovations, sup- ported by actual field data, have been initiated into the GRATE-KILN System design to positively address these factors. This paper presents the recent state of the art design concepts which have helped the GRATE- KILN System assume worldwide acceptance status.

Jan 1, 1983

By Kanaya Koichiro

Doyashiki Concentrator in Hanaoka mine of Dowa Mining Co., Ltd. started the operation in 1943, treating the ore mainly from Doyashiki ore deposits. After the cessation of mining of Doyashiki ore body in 1973, Doyashiki concentrator began to treat the ore from Fukazawa mine instead in the same year, and furthermore the ore from Ezuri mine In 1979. Currently Doyashiki concentrator treats 30,000 tons of ore per month from both mines. The ore treated is complex sulfide ore, called "Kuroko" (black ore), and the principal minerals contained in the ore are chalcopyrite, galena, sphalerite, pyrite, and barite, accompanied by bornite, tetrahedrite, tennantite, covellite, stromeyerite, argentite, polybasite, pearcite, and electrum. The Principal gangue minerals are quartz, gypsum and clay. The grade of the feed to the concentrator averages 0.9 p/t Au, 110 g/t Ag, 1.1 %Cu, 2.8 %Pb, 9.2 %Zn, 5.0 % Pyrite-S and 13% BaS04. The feed is, after washing and two-stage crushing, ground to 88% minus 200 mesh in a rod mill and ball mills with cyclone classifiers, and five concentrates are recovered by flotation. Primarily copper-lead bulk concentrate is recovered by sulfurous acid-lime flotation method, and then from the bulk concentrate copper concentrate is floated by hot pulp flotation method, sinks being lead concentrate. Zinc concentrate is recovered from the tailing of copper-lead bulk flotation, pyrite concentrate from zinc flotation tailing and barite concentrate from pyrite flotation tailing. The final tailing is sent to the dam.

Jan 1, 1982

The Research Centres Program initiated by the Federal Government and supported by the mining industry has had a major impact on geoscience research and education during the past five years. Eight major university based-Geoscience Research Centres are currently supported by the Government, including four Key Centres of Teaching and Research and a further four Cooperative Research Centres (CRCs). The Research Centres Program has led to a concentration of high quality research and teaching in areas of demand and strategic importance creating strong university - industry linkages and a source of well trained and motivated graduates. Over the last decade Australia's reputation as a leader in mineral exploration and ore deposit research has grown substantially, in part because of the development of the Research Centres Program, and to increased collaboration and interaction between research groups and exploration geoscientists across the industry. During a period when ore deposit research activity has been decreasing in other countries (eg USA, Canada, Japan and most European countries), equivalent research activities in Australia have been increasing, within a well co-ordinated national framework. The future challenge for universities and the mining industry will be to maintain the momentum of the successful research centres in order for the centres to become self-funding over a six- to nine-year period.

Jan 1, 1996

By Jock McGregor, Deepak Malhotra, Leonard Harris

After more than 100 years, alkaline cyanide leaching of gold and silver ores, either directly in the case of oxidized ores, or after pretreatment of refractory ores by roasting, pres­sure leaching or bacterial leaching, remains the dominant r leaching method to extract the precious metals f om ores. Leaching with halides (chlorine, bromine and iodine) and with thiourea and thiosulfates is less common but prac­ticed in some cases to dissolve the precious metals both from ores and jewelry and electronic scrap. Cyanide solutions can contain from 1 ppm Au to 30,000 ppm Au. According to the source, i.e., agitated tank leach­ing, heap leaching, eluates from stripping activated carbon or waste electroplating solutions. Similar variations occur with silver which can have a profound influence on the recovery method. The presence of other elements in the leach solu­tions, particularly mercury and copper, likewise play an important role in the procedures required to recover the gold r and silver values f om solution. The same circumstances are found when lixivants other than cyanide are used to dissolve the precious metals. For decades, the preferred method of recovering gold and silver values from alkaline cyanide leach solutions was by zinc dust precipitation according to the Merrill Crowe process developed in the late 19th century. Finely ground gold and silver ores or concentrates were either leached directly or after roasting, in agitated tanks or Pachucas and subjected to solid/liquid separation by filtering or by treat­ment in counter-current-decantation washing thickeners (CCD). This solid/liquid separation step was often very dif­ficult especially when ores containing high quantities of clay were treated which caused filtration or thickening problems. Following testing and development by the U.S. Bureau of Mines (USBM) in the late 60s, the introduction of carbon­in-leach (CIL) or carbon-in-pulp (CIP) plants to recover gold and silver from leach pulps was one of the greatest opera­tional and cost saving improvements made in the industry in South Dakota and quickly spread around the world to be the most common process to recover gold and silver from cyanide solutions.

Jan 1, 2000

By JSrvinen A, Yll÷ E

At Cominco's Zinc Refinery at Trail, British Columbia impurities are removed from zinc sulphate electrolyte by a two-stage purification process using zinc dust. Copper, cadmium and thallium are removed in the first stage whereas cobalt is removed in the second stage. Cobalt removal kinetics are affected by soluble antimony and copper additions to the electrolyte. This study was focused on the kinetics of cobalt removal by zinc powder cementation. Experimental variables included copper and antimony concentrations, pH and temperature. Common organic additives employed in zinc plants were studied to determine potential interactions with the cobalt removal process. Cementation products obtained from laboratory experiments and plant practice were studied using SEM. A number of significant results were obtained: 1. Copper and antimony ions were sustantially removed from solution during the early stages of the cementation reaction (within the first 15 minutes). Cobalt cementation kinetics are slow and follow a first order kinetic regime. 2. A drop in the cobalt removal rates can be correlated with a rise in the Eh of the slurry. 3. Ligninsulphonate, Percol 351 and animal glue at levels of 2 mg/L significantly impede cobalt cementation.

Jan 1, 1993

By Harlowe Hardinqe

ABOUT three years ago a distinctive new type of crushing and grinding equipment, known as the Hadsel mill, was announced. A description appeared in the November, 1932, issue of this magazine. Any machine that would take run-of-mine ore and reduce it, in one operation, and at a reasonable cost, to a size suitable for metallurgical treatment was bound to attract much interest, as the original Hadsel mill did. The first commercial sizes were built with the drum supported by an overhung shaft and partly immersed in a tank. The drum carried inside and outside buckets to lift the ore, which was dropped as the drum revolved onto stationary breaker plates projecting into the drum from the opposite tank wall. The coarser material settled back into the inside buckets. Intermediate sizes were carried into the tank, and this material was scooped out by the outside buckets and deposited hack in the drum for further grinding. The fines were carried out of the mill with the wash water over an adjustable weir at one side of the tank.

Jan 1, 1935

By R. Fred Pena

The Tower Mill has proven to be a grinding machine with a demonstrated application flexibility. Variations in applications have proven to be numerous. This mill was originally intended for fine grinding applications. Subsequent testwork and installations have demonstrated the mill can be utilized in place of ball mills as secondary mills. The following lists a few of the circuits tested: 1. Tower Mill secondary receiving feed from a primary SAG mill grinding stage. 2. Tower Mill as tertiary grind unit following a rod mill/ball mill. 3. Tower Mill as secondary grind unit following a primary ball mill. 4. Tower Mill as a limeslaker. 5. Tower Mill grinding as a primary unit taking limestone crusher discharge. Applications demonstrate the mill is energy efficient and is sensitive to the following consideration: 1. Circuit chosen. 2. Top size of feed. 3. Product size required. 4. Classification equipment performance. 5. Media size required. 6. Media type required.

Jan 1, 1986

By Fred Leighton, Wilson Blake

The microseismic method of detecting instability and high-stress zones in underground mines was developed by the U.S. Bureau of Mines (USBM) in the early 1940's.l,2 For about 25 years this method has been used throughout the world by mining and construction companies in assessing the stability of underground and surface excavations. Rock noises are the release of small amounts of stored strain energy propagating outward from their source as a seismic wave that can be detected with special geophysical equipment. This release of strain energy is caused by a rock mass undergoing load changes resulting in small-scale displacement adjustments such as microcracking, shearing, sliding, and crushing of crystal grains, some even as small as the elastic displacements themselves. No detailed field studies of any of these mechanisms have been made, and knowledge about the origin of rock noises is relatively incomplete. Laboratory tests have shown that when rocks are stressed in a testing machine, the rock noise rate-the number of rock noises generated per unit of time increases with increasing applied stress.3 This increase is most pronounced as the ultimate strength of the rock is approached. The standard field procedure has been to monitor a rock structure at intervals and plot rock noise rates vs. time, thus gaining a semiquantitative estimate of the behavior and stability of the structure. The success of such monitoring, however, has depended almost entirely on the experience and knowledge of the operator, his interpretation of the data, and his equipment. Very little study has been devoted to the basic properties of the vibration record of a rock noise. USBM decided that the microseismic method was being used sufficiently by various mining and construction companies

Jan 1, 1970

By J Nantel

Planning of modern mines entails considerable challenges in the areas of ground control, materials handling, safety, environment, equipment and personnel. Many orebodies are not economical unless efficient mining systems are used to win the ore. Relentless pressures are placed on mine operators to force them to become more productive and to make mines more competitive in modern economies. This has generated an intense drive to adopt technologies that rely on a greater degree of mechanisation, automation and computerisation. There is no turning back; high technology in mines is here to stay: computer controls and monitoring, computer aided mine design, information management systems, etc. During the past 20 years significant advances have been made in the areas of mine design, mine equipment and geomechanics. One could rhetorically ask if the advances in mine backfill technologies have kept pace with developments in other sectors of the mining industry. This paper will look at a few key mining technology sectors and will compare the relative progress of backfill technology to these sectors.

Jan 1, 1998

Planning of modern mines entails considerable challenges in the areas of ground control, materials handling, safety, environment, equipment and personnel. Many orebodies are not economical unless efficient mining systems are used to win the ore. Relentless pressures are placed on mine operators to force them to become more productive and to make mines more competitive in modern economies. This has generated an intense drive to adopt technologies that rely on a greater degree of mechanisation, automation and computerisation. There is no turning back; high technology in mines is here to stay: computer controls and monitoring, computer aided mine design, information management systems, etc. During the past 20 years significant advances have been made in the areas of mine design, mine equipment and geomechanics. One could rhetorically ask if the advances in mine backfill technologies have kept pace with developments in other sectors of the mining industry. This paper will look at a few key mining technology sectors and will compare the relative progress of backfill technology to these sectors.

Jan 1, 1998

By Norman A. Parlee

Introduction The principal primary iron and steel producing capacity of the Dominion Steel and Coal Corporation is at the Dominion Iron and Steel, Limited, plant at Sydney, Cape Breton Island, Nova Scotia. The main raw materials are Cape Breton coal, Wabana (Newfoundland) iron ore, and Port-au-Port (Newfoundland) limestone. This plant, which was established at the turn of the century has gradually expanded its production facilities so that today its ingot producing capacity is over 720,000 tons annually. Principal operating units of the plant at present are three batteries of 173 Koppers by-product coke ovens with conventional by-product recovery equipment, three blast furnaces .of 15 ft. 6 in., 18 ft. 3 in., and 19 ft. 3 in. hearth diameter (inside the brick), one 700-ton hot metal mixer, ten open hearth furnaces (two of 175-ton capacity, three 12 5-ton, five 60-ton), one 10-ton electric furnace, a 40-inch blooming mill, a billet mill, a rail mill, a tie plate mill, rod and bar mills, and a wire and nail mill. Extensive machine shops and an iron and brass foundry are also available for plant maintenance and repairs. This paper will describe developments during the past five years and those now in process. It will also briefly discuss research being done and indicate the direction of future development.

Jan 1, 1951

By V 9. 0 / 300 dpi

In the time period from the early 1980's to the present, longwall roof support technology has evolved tremendously. Chock supports and caliper shields were replaced by 2-leg or 4-leg lemniscate shields. The lemniscate linkage for which the support is named offers numerous advantages to the sup-port both as a fabricated structure and to its performance in the mining application. The hydraulic system, which is the dynamic element of the roof support, was essentially unchanged in early lemniscate shields with the exception of the complexity of additional hydraulic circuits to power a canopy tilt cylinder and canopy side-seals. The control of these fluid-powered functions was provided by direct manual control of valves energizing individual functions onboard the roof-support or the adjacent roof-support. This control valve-gear was comprised of multiple individual valves arranged in a "bank" or integrated into a single hydraulic distribution block with a single operating handle to select any independent function.

Jan 1, 1993

By Fred T. Towne

There are a number of air classifiers manufactured throughout the United States and the rest of the world. The classifiers manufactured by Alpine, A. G. of Augsburg, Germany, are unique in their abilities. It is this uniqueness that I wish to delve into and in this respect we will limit this discussion primarily to the classifiers as manufactured by Alpine. It has been reported in the past that these classifiers were introduced into the. United States in the late 50's. Until the introduction of the Alpine Classifiers, air classification seldom produced a satisfactory fractionation of a product below 45 microns (325 mesh) or above approximately 22 mesh. It has been a common practice to classify fine materials which used water as a carrier medium The use of centrifuges are today producing thousands of tons of finely partitive powders in the very small particle size range. The use of centrifuges in connection with wet grinding mills has increased the rates of production of these mills considerably.

Jan 1, 1965

The approach to this subject is a very general one, but an attempt has been made to cover briefly a very wide field in the nationally important job of manufacturing iron for the iron and steel industry.Some historical data concerning the development of the furnace itself from early days have been followed by the modern ideas on raw materials and their beneficiation. Recent furnace design and modern auxiliaries have been given attention with, finally, some developments in practical operation.HISTORICALWhen dealing with such large 'and costly operating units as blast furnaces, there is not the same opportunity for research in design as in most other metallurgical processes. Over past generations the development of furnace design, or "lines" as it is usually termed, as well as most radical operating changes, has been very gradual.However, there have been some periods of rapid progress due to revolutionary changes. One such was the adoption of the steam engine for blowing and charging operations, and also, during this same era, about 1750, coke was first used as fuel in place of charcoal. Another revolutionary change came some 100 years later, when heating the blast became usual practice.Since then there have been great improvements in mechanical equipment and in the preparation of raw .materials. These factors, together with a better understanding of what happens inside the furnace, have led to the development of those large mechanically operated structures which are the most modern in blast furnace design.For many, years America has led the world in pig iron production and in furnace development, so that American design and practice is now recognised almost as standard. This type of furnace replaced the older stacks in England, Russia, Germany, South Africa and India, as well as here in Australia.

Jan 1, 1947

By S. C. Tadolini

The use of resin-grouted cable supports to control large ground movements in several types of underground mines has increased substantially since being introduced in 1991. Cables offer several advantages over traditional support systems, having large support capacities coupled with the flexibility to be used in low openings. Cable slings have been designed to be installed on-cycle using no-spin technology or a two-piece unit that can be placed with hand-held drilling equipment. Additionally, yielding cable supports have been developed and are being used to control large amounts of movement in coal and evaporite deposits.

Jan 1, 1998