Search Documents

By J. F. Barkley

"In trying various coals at one of the Government power plants, comparison was made of the ash softening temperature of each coal, with the clinkering tendencies of the coal when burned in the furnace. The proximate analyses, ash softening temperature and plant reports as to clinkering were tabulated. It was desired to bring out any correlation that might appear between the ash softening temperature found in the laboratory, and the clinkering of the ash as found in the boiler furnace.Each coal used was sampled and analyzed, and the standard ash fusion test made. The clinkerring of the coal in the furnace was observed by the furnace operator. The furnace equipment consisted of the ""V"" or Murphy type of stoker with the ordinary fire-brick arch roof. With such arrangement very high furnace temperatures are apt to be produced at the ratings carried at this plant.The softening temperature of ash is defined as the temperature at which small cone of the ash, as tested in the laboratory furnace, has fused down to a spherical lump, The softening interval is the difference between the softening temperature and the temperature at which the first rounding, or bending, of the apex of the cone takes piece. The flowing interval is the difference between the softening temperature and the temperature at which the ash has reached a fluid condition as shown by spreading out over the base in a flat layer.While the analyses of the different samples of the some coal did not vary appreciably, the ash softening temperatures were not always so consistent. It will be noted from the following examples that the ash softening temperatures of different samples of the same coal differ as much as 290° F, Hence, in order to judge this property of a coal, many samples ore desirable, taken from many different shipment."

Aug 1, 1924

By G. W. Jones

Gas analysis is of great practical value to the combustion engineer as a guide in the proper deli and operation of power and heating plants. The automotive industry, however, has made little use of gas analysis in the design and construction of engines. Tests4 made by the Bureau of Mines have shorn that for the average motor vehicle approximately 30 per cent of the heat value of the gasoline passes out in the exhaust as incomplete-combustion products. The tendency at present is to pay more attention to ease and flexibility of operation than to efficiency of combustion. However, neither condition can be fully realized except where each cylinder gets a mixture of the same composition - that is, when certain cylinders do not "load up" with gas at the expense of the others. When this occurs, due to some of the cylinders having too rich a mixture while in others it is too lean, it is impossible to get efficient combustion from the fuel used. Gas analysis enables the engineer to determine the quality of the mixture fed to the different cylinders with a high degree of precision. Briefly, the method consists in making an analysis of the exhaust gas from each cylinder while the engine is in operation.

Jan 1, 1924

By Rudolf Kudlich

"The realization that fuel costs, high as compared with those enjoyed prior to the war, are apparently permanent, has caused steam power plant operators to apply their best efforts towards improving the fuel economy of their plants.Though they have given much attention to the reduction in combustion losses by improving methods of firing and improved equipment, and to diminishing the heat losses by more care in maintaining clean heating surfaces and tight and adequate baffling, they have almost universally neglected the waste that occurs from discarding unconsumed combustible with the boiler refuse.This loss varies between extremely wide limits, depending on the quality of the coal, the type of plant and the firing practice in general, the higher the ash content of the coal the greater will be the amount of combustible appearing in the refuse, and the losses will be greater as the boilers are driven at higher ratings. The refuse from stoker fired boilers is apt to have a lower aver-eve percentage of combustible than that from hand fired boilers if operated at the same rating, but stoker fired boilers are usually pushed to higher ratings and the combustible in the refuse will run higher.In actual operating practice the amount of unconsumed combustible in the boiler refuse may range from a few percent to as high as forty or fifty percent. In an informal statement one well known combustion engineer estimates that the average amount of combustible in the refuse from a large stoker fired central station boiler plant is about 15 or 20%. Assuming that the coal burned contains 12% of ash, and allowing for flue dust losses, approximately two percent of the coal will be lost through this channel. The operating engineer of one large modern central power plant reports that when burning coal of about the same ash content, the average amount of combustible in the refuse was in the neighborhood of 33%, en tailing a loss of approximately 4% of the heating value of the fuel fired. Where the coal used daily runs up into hundreds of tons, an appreciable economy could be effected by recovering this percentage."

Sep 1, 1924

By P. D. Tracy, M. W. Von Bernewitz

"IntroductionA study of 256 coal-mine explosions, which occurred during the period 1909-1924 killed 4113 men and injured 570 others, reveals the fact that there are the critical times of day when explosions are most likely to occur, and when corresponding care should be exercised to guard against disaster. Of these 256 explosions, 83 straight as explosions, 89 were straight coal-dust explosions, and 81 were mixed gas and dust explosions, while three were undetermined.It has been determined from the times given in these reports (in several cases no times were given,that the critical period in the morning ranges between 6 and 9 o'clock when 83 explosions took place with a peal. at 7;30 o'clock. Of these 55 were straight gas explosions, the remainder being either coal dust or mixed gas and coal dust explosions. The critical period in the afternoon or early ranges between 3 and 7 o'clock, when 113 explosions took place, with a peak at 6 o'clock. Of these, 87 wore straight coal-dust explosions the remainder being neither gas or mixed gas and coal-dust explosions. Between these morning and evening periods is one which might be called the noon period - that is, from 11m to 7. p. m. - when 26 explosions occurred while some of these were normal type of explosions - that is, as to causes - others were of unusual cause and character, and. are discussed later. A number of explosions (29 in all) took place during mid-afternoon, late at night, and early in the morning - that is, after midnight."

Sep 1, 1924

By W. W. Adams

"The main purpose in the compilation of accident statistics is to reveal conditions that may result in injury to persons or property so that remedial measures may be applied. For practical reasons it is usually found necessary to restrict inquiry to conditions which actually have caused personal injury, and to omit those which nay, but have not yet, resulted in damage, Fortunately or unfortunately, there is a sufficient number of the former to indicate the existence of hazards so numerous as to require all of the attention which the industry can devote to the subject.Two years ago, the Bureau of 'mines, in cooperation with the National Safety Council, undertook an intensive campaign to obtain more complete and satisfactory information regarding mine accidents than had theretofore been available. Since 1911 the bureau had been receiving annual summaries from all companies operating metal mines, showing, in a general way, the number and causes of accidents that occurred during the preceding year and the number of men employed at the mines. Monthly summaries of fatal accidents at coal mines were received from the state inspectors, showing the number of deaths attributed to each of 22 main causes of accidents, Information for individual coal mines was not furnished.While this information, nation-wide in scope, is indispensable because it epitomizes the progress or retrogression in the industry as a whole, and serves as a background of specialized studies, yet certain classes of acci¬dents, for example, those that are more or less peculiar to specific districts or mines, require an analysis in greater detail than is possible on the sole basis afforded by the annual summaries.The need for more specific information was realized some years ago in the State of Pennsylvania in connection with the administration of the workmen's compensation law, The mining industry is well acquainted with the val¬uable studies of accidents, particularly nonfatal accidents, in the mines of that State being conducted by Mr. Rush N. Hosier."

Sep 1, 1924

By W. M. Weigel

"Sand is one of the most useful and, fortunately, one of the most common mineral commodities. By far the largest proportion of the production is used in construction, including all forms of building, concrete and paving, sand for this purpose is produced in every State in appreciable amounts. Excluding send used for railroad ballast, molding sand stands not in tonnage produced, followed by glass sand.Special sands. In addition to the above, many grades of sands, with special characteristics, are used in industrial processes, and may be classed in a group as ""special sends"". This includes filter sand, sand blast sand, engine sand, abrasive send, fire or furnace send, special flooring sand, roofing sand used as a finish for prepared roofings and pottery placing sand sand blast and filter sand have been discussed in previous reports.Very few send companies depend upon the production of any one of these grades, as their source of revenue. They are generally especially prepared from the bank run of sand by different methods of screening or washing, or may, in some instances, be by-products from the production of ether grades. Many companies not now producing them might be able to supply local demands by a slight addition to their plant. In nearly all cases, they command a better price than the usual grades of building sand.Definitions and Properties.Engine sand, or traction sand, as it is sometimes called, is used to prevent the slipping of the driving wheels of locomotives, or other self-propelled vehicles, on wet or slippery rails. Its greatest use is, of course, for railroad locomotives, but street cars use considerable amounts and mine locomotives require its use. As the send must be very dry when used, most consumers have their can drying equipment, so it is often shipped damp, with its natural water content on what resulting from washing by the producer."

Oct 1, 1924

By J. W. Paul

This paper deals with the second phase of an extensive research on coal-mine ventilation factors. A comprehensive report of the entire work is in course of preparation, but abstracts of the various chapters are being prepared in order to make the results public as rapidly as possible. Part 1 dealt with the resistance of unobstructed entries and was issued as Serial 2621 of the Bureau of Mines, in July 1924. Description of tests. After the resistance of an unobstructed entry to flow of air had been determined by tests in the Experiment mine, mine cars were; run into the test section in various arrangements and the increase in resistance was determined. The cars used were of the wooden type with loose end gate, and would hold about one ton of coal, level full. They were 7 feet long. 4 feet 2 inches wide above the wheels, 3 feet high, and had a cross-sectional area of approximately 10 square feet. The average area of the entry was about 57 square feet, the ratio of unobstructed to total area being about 17.6 per cent. The track gage was 42 inches and the wheel-base 20 inches.

Jan 1, 1924

By J. J. Jakosky, D. H. Zellers

"IntroductionThe Bureau of Mines has been conducting experiments in underground communication during a period of several years, and a brief summary of what has been done is as follows:During 1919-1920, investigations were conducted with the geophone. This instrument was used extensively during the World War for detecting enemy digging and mining operations, by means of the vibrations transmitted through the earth strata.A preliminary investigation using short wave-length (200 to 300 meters) radio equipment carried out jointly with engineers of the Westinghouse Electric & Mfg, Co. during 1922.The step was to investigate ground conduction signaling, (called T.P.S. in Signal Corps parlance)."

Nov 1, 1924

By Chas. E. van Baraeveld

"The information presented in this report is a by-product of studies concerning zinc, and is published in response to various inquiries for information as to the suitability of zinc for roofing. It parallels a previous report of the Bureau of Mines on slate roofing.Available Forms of Zinc RoofingZinc is available for roofing in three forms: 1. As sheet zinc which may be used advantageously on roofs with as flat a pitch as 1 in 4; laid with standing seam construction for small roofs and with batten construction for large roofs. 2. As corrugate sheets, in widths up to 40 inches and in lengths up to 8 and feet, available for siding and roofing in industrial buildings (with certain re¬strict ions) and or farm buildings (without restrictions). 3. In the form of shingles.Advantages of Zinc Roofing1. Zinc is a permeant roofing material; that is, when suited to the conditions, and properly applied to a roof designed with the right purlin spacing it will outlast the building and still have a salvage value equal to a least half the original material cost. It is applicable to a wide range of conditions, from the most expensive to the cheapest type of construction, and is not greatly above the cheaper materials in first cost. A permanent roof of simple outline need not cost over $15 to $25 per square (100 square feet), depending upon the method of construction required a corrugated sheet roof for industrial purposes or for farm use need not cost over $15 per square for ordinary conditions. 3. Corrugated zinc sheets have the distinct advantage of being available for re-use and re-construction if handled with ordinary care. 4. Zinc oxidizes to a certain point, building up a strong protective coating which in time effectually checks further oxidation; thus it does not oxidize to the point of destruction as steel does, 5. It is light and easily handled."

Nov 1, 1924

By Bernard M. Larsen, Clyde F. Williams, Edward P. Barrett

"Introduction.The Bureau of Mines at its Northwest Experiment station has been studying the production of sponge iron for the past four years, and during 1923 progress advanced to the point industrial applications can be safely considered. A furnace was operated commercially at silver City, Utah, producing about three tons of sponge iron daily.The Bureau was led to undertake this work by the interest in the use of sponge iron for copper precipitation and for conversion to iron and steel in the electric furnace.If a piece of iron oxide is completely reduced at such a low temperature (850 to 900° C) that no sintering or fusion takes place, then the piece of metallic iron formed has the same size and shape as the original piece of oxide on account of the removal of oxygen, the structure is finely porous, exposing a large surface of iron, and the apparent density is less than that of the original piece of iron oxide. This material is called ""sponge iron"". Chemically, it is a very reactive material."

Nov 1, 1924

By R. R. Sayers

"Health hazards in the mining industry may be attributed to (1) abnormal conditions of the air, (2) improper sewage disposal, (3) bad drinking water, (4) bad illumination, and (5) local mechanical irritation.Abnormal conditions of the air may be due either to physical or chemical changes. The physical changes are (1) abnormal temperature, (2) abnormal humidity, (3) air movement, and (4) presence of dusts. Dusts may be either poisonous, as salts of lead, arsenic, zinc, or mercury; or nonpoisonous, as dust from coal, silica or quartz, limestone, gypsum, or silicates. Chemical changes may be due to changes in the normal constituents, as lowered oxygen or increased carbon dioxide; or to the addition of abnormal constituents, as carbon monoxide (white damp), hydrogen sulphide (stink damp), sulphur dioxide, methane (marsh gas, fire damp), hydrogen, and nitrogen.Effects of High Temperatures and Humidities The effects of various temperatures and relative humidities have been studied in mines in many countries. Harrington and myself studied them in the metal mines of this country and, in a report written recently, they have been summarized as follows:A. Remaining at rest in saturated air at 91 1/2° F, for one hour, With no air movement caused -1. An increase in body temperature;2. A moderate increase in pulse rate;3. Profuse sweating;4. After effects of dizziness and weakness with air movement caused ¬1. Slight or no increase in body temperature"

Dec 1, 1924

By Ernest A. Hersam

"INTRODUCTION.Luring the year 1923 a complete survey was made of the condition of research in the reduction (milling) and concentration of ores and nonmetallic minerals - that is, up to the stage where the ores or concentrates were ready for hydro- or pyro-metallurgical treatment. This survey was carried on under the general supervision of L. A. Lyon, assistant director and chief metallurgist of the Bureau of mines, in cooperation with the milling committee of the American Institute of mining and metallurgical Engineers, the Massachusetts Institute of Technology, and the University of California. Other institutions, including the National Research council, were of assistance and outlined recommendations during the study.While this report is on ""ore dressing"", it contains short sections on coal and clay. The mechanical handling that these minerals undergo is ""dressing"", so that ore dressing is inclusive of metallic and nonmetallic minerals. ""milling"", in its broadest sense, includes with ore dressing certain other metallurgical treatment which the report is not designed to cover.The survey revealed that considerable experimentation is being carried on great cost to the mining industry, but that the research is in general poorly coordinated while companies and firms are adequately taking care of routine tests and the mechanical features involved in their own operations, no comprehensive study of the fundamental principles of ore reduction is now in progress or contemplated. Many industries, besides mining, are interested in the preparation of materials for final treatment, rendering this investigation of value also to them. This class of fundamental research is neglected by industry unless there is some agency which can bring together at least a majority of this interested in a cooperative effort. It can not be effectively handled by a single company; and, moreover, no company can be expected to bear the whole burden of an investigation to benefit the entire industry or a number of industries hence there is need for concerted study within reasonable limits. Furthermore, co-operation eliminates duplication, which is largely a waste of effort and capital."

Mar 1, 1925

By W. P. Yast, R. R. Slyers, J. H. Hildebrand

 The Bureau of Mines, in conducting investigations of atmospheres in mines and tunnels for the purposes of determining and combating hazards to the health and safety of workers, has from time to time closely cooperated with municipal, State and Federal agencies in safety work in engineering and ventilating probleme. Recently the writers have conducted experiments with animals and men breathing helium-oxygen mixtures under pressure. The object of this work was to determine whether helium-oxygen atmospheres can be utilized to advantage in place of normal air for caisson and diving work. In such work the permissible pressures and times of compression and decompression are limited by the physiological effects on man. The major effect is that the nitrogen, (which is the inert con- stituent of normal air and is absorbed by the body tissues and fluids in abnormal amounts when under pressure,) tends to form bubbles in the tissues on too rapid discompression from high pressures. The Bureau of Mines is interested in this problem on account of the pos- sibilities of mitigating caisson illness in tunnel construction and other engine eering operations requiring men to work in compressed air. In addition, the Navy Department is interested on account of the possibilities for extending the range of salvaging and marine engineering operations. The results of the experiments conducted by the writers lead to the following conclusions: Helium is without odor or taste and has physical properties which promise to be of interest physiologically and which have been found to have possibilities of creat practical use, especially in making a synthetic atmosphere that will re- duce the hazard of caisson disease. The substitution of helium for the nitrogen ordinarily present in the air we breathe has been found to result in an atmosphere which it as respirable as that provided by nature. The results obtained indicate that helium not only has the advantage of being less soluble than nitrogen, but

Feb 1, 1925

By J. J. Jakosky, D. H. Zellers

"IntroductionThis paper is the seventh of a series describing an investigation being conducted by the Bureau of Mines on underground communication. A review of past work and results obtained has been published. The present paper deals with a study of line-radio or wired-wireless methods of communication, herein electrical energy is transmitted by metallic conductors.The use of line-radio over metallic conductors has been practiced for a number of years, and at present is being used on a large scale in long-distance carrier-current telephone and telegraph. The early work of the U. S. Army Signal Corps and the Bureau of Standards in using ordinary radio transmitting and receiving apparatus for communication over metallic conductors was been descried. Later publications describe commercial applications, and an excellent treatise and resume is given by E. Colpitts and C. B. Blackwell.Scope of ReportThis report contains (1) a discussion of the chief factors affecting carrier-current transmission, with particular reference in application to underground communication for mines; (2) a description of typical underground circuits used for power and lighting; and (3) description of apparatus used and results obtained in line-radio experiments in coal mines near Pittsburgh, with circuit diagrams, and conclusions as to power requirements and limitations for mine use."

Apr 1, 1925

By C. O. Anderson, W. M. Meyers

Since 1922, when a brief report3 on the production and utilization of garnet was issued by the Bureau of Mines, there have been a number of interest—in developments in the technology of that mineral. Greater activity has been displayed in mining, new mills have been erected, and more attention has been paid to improvements in milling so that a more efficient and economical recovery of garnet has been possible. These activities have resulted in larger production; therefore, attempts are being made to broaden the market for garnet abrasives, and to find new uses for the unusual combination of physical properties than this mineral possesses. The writers have recently completed a field study of the occurrence, methods of mining and milling of garnet, and the manufacture and utilization of abrasive garnet products. This preliminary report indicates the most important sources of garnet, the methods by which it is recovered, and the manner in which it is recovered, and the manner in which it is utilized.Chemical and Physical Properties.The term ""garnet"" is applied to a closely related group of minerals which crystallize in the caste forms and possess similar physical properties, although their chemical composition may exhibit greater variation. The chemical composition of the garnet group may be represented by the general formula 3R"" O.R""' 203.3S102, in which R represents the bivalent elements calcium, magnesium, in the manganese state and ferrous iron, R"" represents the trivalent elements, ferric iron, aluminum and chromium in the chromie state. An account of the amorphous substitution of the different bivalent and trivalent elements, specimens whose composition may be represented by a definite formula are rare, the composition of any given specimen generally exhibits treat complexity.

Jun 1, 1925

By D. B. Dow

This paper on the physical chemistry of oil-field emulsions is the last of a series of three prepared as a result of a study of oil-field emulsions. The first paper3 deals with the factors responsible for the formation of emulsions, find the second4 with methods now utilized for dehydrating oil-field emulsions. A more complete report of the whole investigation is in preparation. The laws governing the formation and resolution of oil-field emulsions fall in that branch of physical chemistry doling with colloids. Much work has been done by the physical chemist on colloids And emulsions, and, although most of this work was on commercial and pharmaceutical emulsions, yet the principles developed apply in a general gray to oil-field emulsions.

Jan 1, 1925

By J. E. Tiffany, J. J. McKitterick

"IntroductionThe Bureau of Mines is investigating the fundamental factors in breaking down coal at the face, which govern the production of lump coal in typical mines working, different coal beds. Tiffany and Nelson in 1923-21 conducted tests on methods of blasting and use of different explosives, in a mine working the Pittsburgh bed in Pennsylvania. They determined come of these factors quantitatively, and compared their results with those obtained when the regular mine practice was followed.Results of Previous InvestigationThe tests by Tiffany and Nelson showed that the use of the cartridge of smaller diameter than that used in mine practice, resulted in an increase of 5 per cent in the amount of lump coal passing over a 1-1/4-inch bar screen, with a reduction of 32 per cent by weight in amount of explosive required. On the other hand, they found that on reducing the weight of charge 20 per cent, and using the cartridge of larger diameter, the round would not throw down the coal satisfactorily.Experiments with ""snubbing"" showed a similar improvement in quantity of lump coal, end the coal that was blasted rolled forward into the working place. however, in recent tests at another mine where the coal Lad different physical characteristics, snubbing did not always result in the coal rolling forward, on account of clinging to the ribs, and was not found to be an advantage. Therein the writers of this paper recommend that tests be made before deciding upon the adoption of snubbing in a particular mine."

Aug 1, 1925

By Ernest E. Berger

"INTRODUCTIONOne of the outstanding problems in the normetallic industries, and one which involves two of the greatest of these industries, cement and gypsum, is the reaction of Portland cement with calcium sulphate. To all Portland cement clinker there is added in the manufacturing process, a small amount of retarder, as a necessary ingredient of the finished product. This retards the initial set, increases the strength, and adds to the plasticity of the cement so it will have the desired working and setting qualities. The retarder commonly used is gypsum, (CaSOA.2HO), which is the hydrous form calcium sulphate. Calcium sulphate is also available as plaster of Paris (CaSO4 1/2 HC) and anhydrite (CaSO4). The purpose of this inquiry was to determine the form or mixture of forms best adapted for retarder. The problem is complicated by the fact that cement clinker is a complex mixture of calcium silicates and aluminates, and that clinker from different mills, making cement of approximately equal quality, differs considerably in chemical constitution. Thus the same retarder may give very different results with different types of clinker, especially in the percentage of retarder required for the same degree of retardation.It has been known for some time that a small percentage of plaster of Paris will greatly retard the time of set of Portland cement as well as increase its strength and plasticity, but whether gypsum and anhydrite will have a similar effect is as such disputed question. The offects of gypsum have received little consideration in laboratory research because, even though it will not retard a clinker when the two are mixed in the laboratory, as has been noted in some instances, the cement will have a normal set when the two arc mixed in the large tube mill at the plant, so that practically, gypsum seems to be equally as goou as plaster of Paris, and because of the great saving in cost it has been used almost exclusively."

Sep 1, 1925

By C. H. Kats, E. G. Meiter, J. J. Bloomfield

"INTRODUCTION.Street manholes for underground power and signal circuits, and for sewers vary in size from small openings that a workman can enter, to large central vaults. As the gas hazards in manholes are similar to those in mines, the mine safety committee of the Bureau of Mines was asked whether the miners' flame safety lamp is a practicable device for indicating inflammable gases in manholes.The coal miner detects firedamp (methane or CH4) with his flame safety lamp by observing the luminous can or the increased length of flame that appears when 1.5 per cent or more of the combustible gas is present. The lamp flame also warns him of lack of oxygen by going out when the oxygen becomes less than 16 to L7 per cent. A tentative rule regarding the proposed use of safety lamps at manholes has been suggested previously as follows: ""Testing for gas: Do not enter manholes until you have .assured yourself that the manholes are free from dangerous gases, by testing with an approved safety lamp, by ventilation, or by other adequate methods."" The Bureau's committee recommended that miners' flame safety lamps are not suitable,testing in manholes because hydrogen gas may be formed therein. The flame safety lamps approved by the Bureau of Mines for use in aseous mines are safe in presence of methane and while not tested against the members of the paraffin hydrocarbon series (CnH2n+2) higher than methane they been have been used therein; the lamps should not be used in hydrogen or acetylene they can initiate explosions in presence of these gases."

Oct 1, 1925

By C. W., Davie

"DEFINITIONDiatomaceous earth consists almost entirely of the silicious remains of minute flowerless aquatic plants known as diatoms. The name diatomaceous earth, therefore, is to be preferred to others such as trade names, inappropriate terms, or names correctly applied to some other product. The following names should, therefore, not be used for diatomaceous earth,-- kieselguhr, infusorial earth, diatomite, celite, moler, bergnehl, English rottenstone, tripoli, tripolite, fossil earth, desmid earth, white peat, tellurine, randanite, ceyssatite, or any trade name.FORMATIONDiatoms live in practically all kinds of water, fresh or salt, hot or cold, still or running and under different conditions of depth and pressure. These minute plants assimilate inorganic salts from their environment and produce skeletons of silica much as mollusks secrete lime and form their Shalls. When the diatoms die they settle to the bottom together with anything else which may be present, such as sand, clay or volcanic ash. The organic matter gradually disappears leaving the silicious skeletons of the diatoms which, with impurities, make up the deposits of diatomaceous earth. These deposits which are still being foamed at the present time and which were produced throughout very different epochs, were more prolifically formed in the Tertiary, so that the thickest beds so far discovered are of that Age."

Nov 1, 1925