Search Documents

By J. W. Paul

[A study of mining methods and underground practices as they influence injury from falls of roof or coal reveals data as to the location in the mine where such injuries occur with the greatest frequency and as to some of the methods and practices which are in use for the prevention of injury. This paper, which presents statistics bearing on the frequency and place of occurrence of accidents and, discusses regulations and practices which have resulted in a low frequency rate from falls of roof and coal in a few representative mines takes its information from mine-accident reports and from the results of studies conducted in a group of 80 mines in the bituminous coal fields of western Pennsylvania, Ohio, and West Virginia. The statistics from this group of mines cover periods of one to four years but average 2 years and 7 months. During this time these mines produced over 110,400,000 tons of coal, equivalent to one-fifth of the annual production of all bituminous mines in the United States. The coal beds of the mines in the group studied are mostly flat, with local pitches of moderate degree. A number of mining plans are in use, each of which follows a general system of multiple entries, cross entries, and rooms. Room and pillar in panels either advancing, retreating, or half advance and half retreat and the block systems are employed. The methods of pillar extraction are by splitting, slabbing, pocket-and-stump, and open end. It is hoped that in presenting some of the details of the methods and practices at particular mines of this group which have commendable records in the prevention of injury some good may accrue to many other bituminous mines which 'nave similar natural conditions.]

Jan 1, 1933

By R. L. Marek

The number of persons fatally injured in the California petroleum industry in 1932 was 24, a decrease of 6, or 20 percent from the number killed in 1931. The decrease in the number of fatalities occurring in 1932 caused the fatality curve of the California petroleum industry to reach its lowest point in 10 years. Changing conditions in the oil industry - reduced personnel, decreased active field development, and curtailed production - have undoubtedly caused a part of this decrease, but continued accident-prevention efforts by the industry have also contributed to the reduction in the number of fatalities for 1932. The Bureau of Mines has analyzed and reported annually the fatalities in the California petroleum industry for a period of 10 years. Figure 1 shows the trend of fatal accidents during that period. Fatality statistics for 1932 show that the drilling and producing, pipe line and transportation, and refining and natural gasoline divisions of the industry had fewer accidents in 1932 than in 1931, sales and marketing being the only division that showed an increase over 1931. The number of fatalities by divisions for 1931 and 1932, percent of total, and percentages of increase and decrease are given in Table 1.

Jan 1, 1933

By A. C. Richardson

The mine of the Porter Coal Co. is located at the town of Porter in the northwestern part of Jefferson County, Ala., about 20 miles west of Birmingham. The operations in this mine are confined to the middle and bottom benches of the Mary Lee bed. The coal from the Porter mine is handpicked and washed before being placed on the market. The handpicked lump coal and the washed egg and nut coal are sold chiefly as domestic and steam-raising fuel. The coal finer than 1 inch is washed in 2-compartment jigs and utilized in the manufacture of metallurgical coke. The coal company has found that, when coal ranging in size from 1 to 0 inch is washed in jigs, a considerable amount of high-ash material finer than 3/16 inch remains in the washed coal. This paper gives the results of an investigation which was conducted for the purpose of determining the washing characteristics of the through 3/16-inch raw coal and the extent to which the ash might be reduced by means of coal-washing tables. This investigation has been made in connection with an extensive study of the coal-washing problems now being conducted by the United States Bureau of Mines and the University of Alabama, with the cooperation of the coal-mining companies of the State.

Jan 1, 1933

By A. C. Richardson

The mine of the Porter Coal Co. is located at the town of Porter in the northwestern part of Jefferson, County, Ala., about 20 miles west of Birmingham. The operations in this mine are confined to the middle and bottom benches of the Mary Lee bed. The coal from the Porter mine is handpicked and washed before being placed on the market. The handpicked lump coal and the washed egg and nut, coal are sold chiefly as domestic and steam-raising fuel. The coal finer than 1 inch is washed in 2-compartment jigs and utilized in the manufacture of metallurgical coke. The coal company has found that, when coal ranging in size from 1 to 0 inch is washed in jigs, a considerable amount of high-ash material finer than 3/16 inch remains in the washed coal. This paper gives the results of an investigation which was conducted for the purpose of determining the washing characteristics of the through 316-inch raw coal and the extent to which the ash might be reduced by means of coal-washing tables. This investigation has been made in connection with an. extensive study of the coal-washing problems now being conducted by the United States Bureau of Mines and the University of Alabama, with the cooperation of the coal-mining companies of the State.

Jan 1, 1933

By Jr. Reistle

The tests reported in this paper were made in the East Texas field in the summer and fall of 1932 as a part of the Bureau of Mines study of the operation of flowing wells and reservoir performance; and to determine, if possible, the minimum reservoir pressure necessary to produce the wells in this field by natural flow through different sizes of flow strings. The minimum reservoir pressure that would be required to Maintain natural flow through 2 1/2-inch tubing was determined experimentally for the existing energy conditions in the East Texas field. With the present available data, however, it is impossible to predict accurately or to determine by calculation the necessary energy requirements for maintaining the vertical flow of oil and gas mixtures under all conditions. Although some valuable data were obtained which seem to have application to the solution of problems involving vertical flow, this important research of the petroleum industry is so involved that more study of the complicating factors influencing the flow of oil-gas mixtures through vertical pipes is required.

Jan 1, 1933

By Ben E. Lindsly

The study of "bottom-hole samples follows in natural sequence the study of samples obtained under high pressures at the well heads of flowing wells. The principal object of this phase of gas-solubility research, started actively in January, 1930, was to gain a more accurate knowledge of the physical and chemical characteristics of the oil-gas mixtures that exist in natural reservoirs.. In possession of actual data regarding the condition of the oil; the quantity of gas liberated from solution upon dimunition of pressure; and the relative volumetric proportions of gas to oil at various pressures throughout the flow string in a well, it should be possible to predict, with a fair degree of accuracy, That physical changes these mixtures would undergo throughout the life of a pool. Such information not only is important in designing flow strings in flowing Tells but is important also in solving problems relating to pumping efficiency and the power required for pumping. Although certain fundamental data were obtained in the study of samples taken at the well head, "bottom-hole" samples are more representative of subsurface mixtures of oil and gas because they are obtained at reservoir temperatures, and before the oil has had the opportunity of intermingling with extraneous gas; that is, gas which either was not in solution originally, or which was liberated from solution at higher pressure, and later became mixed with the original undissolved gas.

Jan 1, 1933

By Ben E. Lindsly

The study of "bottom-hole' samples follow,-is in natural sequence the study of samples3 obtained under high pressures at the well heads of flowing wells. The principal object of this phase of gas-solubility research, started actively in January, 1530, was to gain a more accurate knowledge of the physical and chemical characteristics of the oil-gas mixtures that exist in natural reservoirs. In possession of actual data regarding the condition of the oil; the quantity of gas liberated from solution upon dimunition of pressure; and the relative volumetric proportions of gas to oil at various pressures throughout the flow string in a well, it should be possible to predict, with a fair degree of accuracy, what physical changes these mixtures would undergo throughout the life of a pool. Such information not only is important in designing flow strings in flowing wells but is important also in solving problems relating to pumping efficiency and the power required for pumping. Although certain fundamental rata Mere obtained in the stud of samples taken at the well head, "bottom-hole" samples are more representative of subsurface mixtures of oil and gas because they are obtained at reservoir temperatures, and before the oil has had the opportunity of intermingling with extraneous gas; that is, gas which either was not in solution originally, or which was liberated from solution at some higher pressure, and later became mired with the original undissolved gas.

Jan 1, 1933

By Fred D. DeVanery

"INTRODUCTION Although galena is the most common lead-bearing mineral, is easily concentrated by gravity methods, and is readily susceptible to flotation, nevertheless some galena-bearing orebodies have within them small deposits of lead ore that fail to give a high recovery when treated by the customary milling methods.The secondary minerals, cerussite and anglesite, which result from natural oxidation of galena, cause losses when the customary method of lead-ore concentration is practiced. The identification of oxidized lead-ore minerals and the efficient concentration of a lead ore taken from the oxidized portion of an orebody which has previously yielded poor recoveries mere the objects of a recent investigation. Thus the ore examined was selected from a large orebody. The work was undertaken at the Mississippi Valley Experiment Station of the United States Bureau of Mines in cooperation with the Missouri School of Mines and Metallurgy, Rolla, Mo.DESCRIPTION OF OREThe ore was of a brownish color owing to oxidation of some of the iron minerals to limonite. The lead content was 6.80 percent, and a cursory examination showed that most of the lead was present as galena. Small amounts of sphalerite, siderite, and pyrite were readily identified. The chief gangue mineral was dolomite, accompanied by smaller amounts of calcite and glauconite."

Jun 1, 1933

By G. W. Jones

In a previous report results were given and a method outlined whereby from a knowledge of the composition of the natural gas and of the inflammability limits of the individual constituents composing the natural gas, the limits of inflammability of natural gas and air mixtures could be closely calculated. This method is based on the application of Le Chatelier's law as modified by Coward, Carpenter and Payman, to apply to a mixture of any number of combustible gases. This law must not be used indiscriminately, because many exceptions have been found. For example, when ethylene, acetylene, hydrogen sulphide, or chlorinated hydrocarbons are present the law may not hold. For a discussion of the rally exceptions which have been found, reference should be made to a report by Coward and Jones. Before this method can be used the inflammable limits of the individual constituents must be known. Also, the composition of the complex combustible mixture, and representative mixtures besides, must be tested both experimentally and by calculation to prove whether Le Chatelier's law may be applied.

Jan 1, 1933

By G. W. Jones

In a previous report'/ results were given and a method outlined whereby from a knowledge of the composition of the natural gas and of the inflammability limits of the individual constituents composing the natural gas, the limits of inflammability of natural gas and air mixtures could be closely calculated. This method is based on the application of Le Chatelier's law as modified by Coward, Carpenter and Payman,5/ to apply to a mixture of any number of combustible gases. This law must not be used indiscriminately, because many exceptions have been found. For example, when ethylene, acetylene, hydrogen sulphide, or chlorinated hydrocarbons are present the law may not hold. For a discussion of the many exceptions which have been found, reference should be made to a report by Coward and Jones.6/

Jan 1, 1933

By H. B. Hill

The discovery of the Oklahoma City field and its .rapid development into one of the major oil-producing districts is an outstanding epoch in the history of the petroleum industry not only of .Oklahoma but also of the United States. The relatively great depth to which the wells were drilled and the large initial production of high-gravity oil are of special significance. The field has boon under proration almost from the time that its development began, and many new production problems have developed out of the changed conditions of operation. The discovery well was first tested in December 1928 at a depth of 6,402 feet, with an initial production of 4,847 barrels of 38.5° A.P.I. gravity and several months later was completed at a depth of 6,624 feet. The large initial production, the high pressure, and the large gas volume in the different horizons of the discovery well suggested the potential possibilities of gas and oil, production in formations of Pennsylvanian and pre-Pennsylvanian age.

Jan 1, 1933

By H. B. Hill

The discovery of the Oklahoma City field and its rapid development into one of the major oil-producing districts is an outstanding epoch in the history of the petroleum industry not only of Oklahoma but also of the United States. The relatively great depth to which the wells were drilled and the large initial production of high-gravity oil are of special significance. The field has boon under proration almost from the time that its development began, and many new production problems have developed out of the changed conditions of operation. The discovery well was first tested in December 1928 at a depth of 6,402 feet, with an initial production of 4,847 barrels of 38,5.° A.P.I. gravity oil, and several months later was, completed at a depth of 6,624 feet, The large initial production, the high pressure, and the large gas volume in the different horizons of the discovery well suggested the potential possibilities of gas and oil, production in formations of Pennsylvanian and pre-Pennsylvanian age.

Jan 1, 1933

By G. L. Oldwright, F. K. Shelton, W. E. Keck

"INTRODUCTION Zinc must be of high grade to satisfy the present demand. Even when the amount of premium paid is small, the purer metal as the buyers' preference. The following specifications for spelter were taken from the American Society for Testing Materials for 1927, Part I, pane 524. (The specifications for 1930, p. 582, are tile same.)Another specification for zinc of a much higher grade than any of the above has been established lately by the same society. The committee on zinc die-casting (Proc. Am. Soc. Test. Mat., vol. 31, 1931, p. 263) reached the following, conclusions: I. ""That the purest of zinc is necessary to produce stable zinc-base die castings, and as a result requested specifications for zinc spelter .with total impurities not over 0.02 percent."" Their tests showed that the die castings made of the purest zinc had the least elongation and the greatest tensile strength, and exhibited the least changes with temperature.Still more far-reaching claims are made for the properties of zinc containing over 99.99 percent metal. Zinc foil, for instance, may someday be made as a common commercial product. It would seem likely that the demand for zinc of high grades rill continue and that even purer varieties may be desired. This demand fits in with the modern trend in manufacturing plants of reducing the number of variables to a minimum by using pure materials, and of controlling the processing of metals during their various stages of fabrication by mechanical means instead of by expert laborers."

Jun 1, 1933

By W. W. Adams

"The eighth National Safety Competition, that for 1932, conducted by the United States Bureau of Mines, was participated in by 322 mines and quarries operating in 34 States. Tables 2 to 6 show the relative standing of the various plants. Bronze trophies, known as the 'Sentinels of Safety,' which were provided by The Explosives Engineer magazine to be awarded annually by the Bureau of Mines, were awarded to five companies, each company having established the best accident-prevention record within one of the five classes into which all companies were divided, - namely, anthracite-mining companies, bituminous-coal-mining companies, metal-mining companies, operators of nonmetallic-mineral mines other than coal mines, and quarries or open-cut mines. The trophies are awarded for one year and are then transferred to the winners of the succeeding year's contest.The trophy for bituminous-coal mines, which has been in New Mexico for the past year, was won by a mine in West Virginia. The metal-mine trophy goes to New York State for the first time in the history of the contest. Previously it had been won by mines in Minnesota, Michigan, Kansas, and Oklahoma. The trophy for nonmetal mines remains for another year at Retsof, N. Y.; that for quarries and open-cut mines is transferred to a quarry in Michigan. The trophy for anthracite mines, of course, remains in Pennsylvania, as all anthracite mines in the contest are in that State.In determining the relative standing of the various companies enrolled in the competition, all mines and quarries were graded according to their accident-severity rates, - that is, according to the number of days of disability of employees on account of accidents in proportion to the number of man-hours of work done by all employees at the plant. Reports of accidents and of man-hours worked were furnished by the companies to the Bureau of Mines. These reports were carefully examined and classified to insure uniform weighting of accidents according to the number of days of disability to be charged and to insure uniformity of methods of calculating the accident-severity rates for the various mines and quarries. When the relative standing of all plants had been determined in this way, a summary of the records of the companies having the lowest accident-severity rates in their respective groups was sent to the members of a committee of award for examination in accordance with the rules governing the safety contest. The members of the committee of award were W. H. Cameron, managing director of the National Safety Council; William Green, president of the American Federation of Labor; James F. Callbreath, secretary of the American Mining Congress; T. T. Read, Vinton professor of mining engineering of Columbia University; C. B. Huntress, executive secretary of the National Coal Association; A. J. R. Curtis, assistant to the general manager of the Portland Cement Association; and A. T. Goldbeck, director of the bureau of engineering of the National Crushed Stone Association. When two or more mines within the same group operated without an accident during the year, the contest rules provided that the trophy for the group should be awarded to the plant whose record showed the largest number of man-hours worked."

Jul 1, 1933

By V. H. Gottschalk, John Grodd, R. S. Dean

"Elemantary ConsiderationsAlthough magnetiem was first discovered in and derives its name from an oxide of iron found in magnesia and called lodestone its pracical uses date from the discoveries of Faraday concerning its relation to the electric current. We may therefore start our discussion of magnetic properties with Faraday's law for relation between induced electromotive force and the change in a magnetic where e is the electromotive force induced in an electric circuit by a unit rate of change of magnetic flux N, H is the intensity of the magnetic field, S is the area enclosed by the circuit, and i an angle between H and the normal to dS. In the simplest case we could use this law to measure the strength of a magnetic field by passing it at a measured rate through a coil of copper wire and determining the,electromotive force. As a matter of practical convenience, it will be simpler to nee the total quantity of electricity produced by a change of magnetic field. For this purpose we may let i denote the strength of the electric current induced by the change of magnetic field in time in a circuit of area a and resistance R. Then the total electric quantity. Q is given. by"

Mar 1, 1934

By B. W. Gandrud

In 1927 Coghill showed that there is considerable liberation of the iron oxide mineral from gangue when the Alabama red iron ores are ground to a size suitable for classification and tabling but that there is not sufficient to make possible a high extraction and a high grade of concentrate. Coghill states: High extraction and 'high grade of concentrate cannot be obtained without grinding to a size comparable with flotation or cyanide practice. If grade of concentrate be sacrificed the grinding need not be so severe. These ores slime readily during grinding, and in most instances the slimes are only slightly higher grade than the original ore. Not only do they carry a considerable percentage of the total iron in the ore, so that to reject them as tailings would result in prohibitively low extraction, but they are too fine to be amenable to ordinary methods of gravity concentration. In 1929 the Bureau of Mines published results showing that certain Alabama oolitic iron ores could be concentrated by classification and tabling after grinding, with rubber-covered rods. This selective grinding produced slimes of much higher grade than the original ore, and they were considered part of the final concentrate.

Jan 1, 1934

By B. W. Gandrud

In 1927 Coghill5 showed that there is considerable liberation of the iron oxide mineral from gangue when the Alabama red iron ores are ground to a size suitable for classification and tabling, but that there is not sufficient to make possible a high extraction and a high grade of concentrate. Coghill states: High extraction and high grade of concentrate cannot be obtained without grinding to a size comparable with flotation or cyanide practice. If grade of concentrate be sacrificed the grinding need not be so severe.

Jan 1, 1934

By B. W. Gandrud

The upper part of the Alabama deposits of crystalline graphite consists of an oxidized ore derived from the underlying unoxidized ore through prolonged Weathering. The degree of oxidation in different sections and at different depths within the bed is not uniform. The original ore is hard and blue-gray; the weathered product is soft and brown and is the only part that has been mined to any extent. Samples of both oxidized and unoxidized ores were obtained from two of the large graphite deposits of Clay County. Three additional samples of oxidized ore were obtained from different portions of a third property in the same region. In this report, ores 1 to 5 are of oxidized material and ores 6 and 7 of unoxidized.

Jan 1, 1934

By E. S. Leaver

The gold that is not recovered by a particular process is refractory to that process. A study to determine how the refractory gold is associated in the ore constituents usually indicates the needed improvement in the process or additional methods for bettering recovery. In preliminary work, segregation of the various minerals, gangue or impurities, and data showing the reactions of each in the recovery method readily confines the refractory gold to a certain part on which extensive research can be directed. In this dissecting plan, the microscope is an important aid in locating the refractory gold but should be supplemented by chemical tests. Each ore is an individual problem until the association of the gold has been determined. Knowing the problem through the interfering minerals or elements, the solution often is only the application of part of a former known practice as an auxiliary or additional feature. In the treatment plan for most gold ores, it has been the custom to try each of the usual recovery methods or combinations thereof, accepting the best results on a basis of the lowest cost. A better plan includes knowledge of the association of the gold and the various minerals from which it is to be recovered. This presents reasonable foresight into the problems that should be expected and permits some provision for avoiding probable difficulties. The preliminary work should include: Determination of the percentage of free gold with classification showing size of gold particles to be expected; determination of the percentage of gold associated with each mineral and whether it be freed from the mineral by crushing; and an analysis of representative samples of the ore to include other valuable minerals and the form in which they occur.

Jan 1, 1934

By Paul Hatmaker

Lime was a highly useful commodity thousands of years before the simple chemistry of its manufacturing process was known. The employment of lime for agriculture, building, and even certain essentially chemical purposes is so old that its origin is among the unrecorded details of man's first ventures into the manufacture and use of prepared substances. Lime is a most versatile material and consequently has come to be widely utilized in modern civilization. Immediately before the depression of the early 1930's the annual production of lime in the United States was more than 4 million tons, valued at 33 to 42 million dollars. This output was sold to many industries, so many that mere enumeration becomes tedious. In addition to agricultural and building lime the sales statistics compiled annually by the Bureau of Mines include lime sold to the steel and other metallurgical industries as refractory and fluxing material, as well as that used by paper mills, glass works, tanneries, and water-treatment plants. These major uses normally consume about 86 percent of the domestic sales. The remaining 14 percent includes lime sold for use in the manufacture of alcohol, alkalies, bleaches, calcium acetate, calcium carbide, coke gas and byproducts, glue, insecticides, oils and fats, paints, and rubber, in the refining of salt, in the manufacture of sand-lime and slag brick, in the disposal of sewage and garbage, in the manufacture of silica brick, in the refining of sugar, in the textile industries, and in wood distillation. Many other uses are also known for which complete sales data are not available.

Jan 1, 1934