Search Documents

By Anuradha Khetwal, Sandeep Khetwal, Andrea Panciera

The observation method is a design optimization approach for the drill and blast method in tunneling. This method includes first identifying the hazard scenarios through site investigation, formulating suitable solutions, obtaining feedback during construction, and finally using that data to optimize the design methods. This paper illustrates the application of the observational method for T-48, a railway tunnel project in the Himalayas. It is a 10.2 km long tunnel with a parallel escape tunnel and 26 cross passages. The use of observational methods in this project optimized the overall tunnel design and considerably saved the overall project cost.

Jun 23, 2024

By Sang-Su Lee

This paper shows the application of the porous plug system in the Mitsubishi continuous copper smelting and converting process. This system has already been adopted and utilized in the steel industry to enhance productivity. Recently, some copper smelters have adopted this system but the results have not been satisfactory. The porous plug system was installed at the anode furnace in December 2001 to reduce the oxidation time and decrease the oil consumption. A good effect was that the nitrogen stirring of the melt through porous plugs improved the melt heat transfer. As the result of the enhancing heat transfer the oil consumption and the build up inside the furnace were actually decreased. But until now the oxidation time has not been sufficiently reduced. In the future, further research and tests are needed in order to increase the productivity and save costs.

Jan 1, 2003

By Sang-Su Lee

This paper shows the application of the porous plug system in the Mitsubishi continuous copper smelting and converting process. This system has already been adopted and utilized in the steel industry to enhance productivity. Recently, some copper smelters have adopted this system but the results have not been satisfactory. The porous plug system was installed at the anode furnace in December 2001 to reduce the oxidation time and decrease the oil consumption. A good effect was that the nitrogen stirring of the melt through porous plugs improved the melt heat transfer. As the result of the enhancing heat transfer the oil consumption and the build-up inside the furnace were actually decreased. But until now the oxidation time has not been sufficiently reduced. In the future, further research and tests are needed in order to increase the productivity and save costs.

Jan 1, 2003

By Max F. Lee, Warren A. Peck

The applicability of the Q-system [Barton et al. 1974] to Australian underground metal mines is discussed with reference to two common design issues: ground support for horizontal mine development, and assessing the stability of bored raises. Installed ground support in mine development is com-pared to empirical estimates using the Q-system and associated support capacity calculations. Data are graphically presented from 59 specially selected sites at 15 contributing mines. The actual performance of large-diameter raise-bored shafts is also compared to empirical stability assessments using a modified version of Q (Qr, after McCracken and Stacey [1989]). Lower-bound Qr values are plotted against raise diameter for 47 selected sites at 23 mines in Australia and Papua New Guinea. The influence on Q and Qr of some geotechnical aspects of the Australian landscape, the dynamic nature of mines (compared to civil construction), and occupational health and safety regulations are discussed. Stability and support assessments that are based just on Q or Qr are not always conclusive. It is often necessary to consider other rock mass parameters, the regulatory environment, and risk issues. These results are interim; further data collection and analysis are required with regard to comparing actual performance versus empirical assessments.

Jan 5, 2007

By J. Kou

The adsorption process, density and structural property of the oleate layer adsorbed onto a hydroxyapatite (HAP) surface at six different concentrations and three pHs (pH 8, 9 and 10) have been studied using the technique of quartz crystal microbalance with dissipation (QCM-D). The present study demonstrated the versatility and accuracy of the QCM-D for surface adsorption characterization. The real-time measurements of frequency and dissipation shifts with a hydroxyapatite-coated sensor revealed changes in the hydroxyapatite surface during the entire adsorption process. Chemisorption and surface precipitation of sodium oleate were also observed on the surface of hydroxyapatite through the use of Fourier Transform infrared spectroscopy(FTIR). Chemisorption dominated at low concentrations and high pH values and formed a rigid and thin adsorption layer. Surface precipitation of calcium oleate and micelles dominated at concentrations higher than critical micelle concentration (CMC) and lower pHs and formed a thick but dissipated adsorption layer with a high hydration level. Three distinct adsorption behaviors were identified from the different slopes of ?D-?f plots. The adsorption density was less than a monolayer at concentrations <0.164 mM, but increased significantly at concentrations higher than 0.821 mM at all three pHs. The critical concentration at pH 8 was 0.33 mM, which was lower than at pH 9 (0.821 mM) and pH 10 (3.3 mM).

Feb 1, 2012

By Gerald W. Elger

Research at the Albany Metallurgy Research Center has shown that high-purity rutile can be produced from relatively low-grade ilmenite obtained from a massive rock deposit. Ilmenite is first smelted in an electric-arc furnace to separate the iron and produce a slag enriched in titanium dioxide. Titania slag mixed with a phosphate flux is then oxidized to synthesize rutile and form a phosphate-glass matrix which contains the impurities. Attrition scrubbing the treated slag in dilute solutions of phosphoric or sulfuric acid liberates the rutile, which is concentrated by physical methods. Tests show that synthesized rutile containing 95 to 97 pct titania responds to chlorination at the same rate as natural rutile.

Jan 1, 1973

By Edgar Shepard

THE interest of the Federal Government in improvement of water-ways dates from 1820, when Congress appropriated $5000 for making a survey of the Mississippi and Ohio Rivers and assigned this work to the Corps of Engineers of the Army. Since that time the Government has gradually assumed increasing jurisdiction in the matter of improvement and control of inland waterways until, by the River and Harbor Act of Jan. 21, 1927, Congress assigned to the Secretary of War and to the Chief of Engineers the duty of making surveys, in accordance with House Document No. 308, 69th Congress, to formulate plans for the most effective improvement of the navigable streams of the United States and their tributaries, for navigation, development of water power, control of floods, and the needs of irrigation. Virtually all the preliminary investi-gations and surveys required by this act have been completed. The reports made to Congress have been published and often are referred to as "308 Reports." The map shown in Fig. 1 is merely a skeleton distribution of the projects covered by these reports, but it serves to indicate the magnitude of the proposed undertaking. In many instances, a single character on the map stands for a major development involving several dams and reservoirs or many miles of canals or levees. The devastating floods of 1936, and the need for worthy public works to take up the slack in employment, gave further impetus to this program and in 1936 led to the enactment of a bill authorizing a large number of these projects.

Jan 1, 1940

By Mason L. Dicks

For many years The Hanna Mining Company has been investigating the flotation of the non-magnetic iron ores located in the Western Mesabi Range of Minnesota.1 During the 1950&apos;s a number of anionic iron procedures were evaluated and in the late 1950&apos;s and early 1960&apos;s the anionic silica floats and the cationic silica floats were tested with improved results.2 The cationic float became more attractive and effective by the use of the improved ether amines. About 1962 a desliming process by selective flocculation was developed by the U.S. Bureau of Hines at Minneapolis&apos;, Minnesota.3, 4, 5 This is a very efficient method of desliming and was first tried with the anionic silica float and then the more practical cationic silica float. In the mid 1960&apos;s The Hanna Research Laboratory began studies to optimize the selective flocculation process for our ores. This was followed by studies to optimize the cationic silica float after desliming by selective flocculation. This testwork was done on large, 500 to 1000 tonne bulk samples of oxidized taconite which were later successfully piloted at .68t/h (1500 Lbs. /hr.). A program was then begun to test the oxidized portions of numerous taconite drill holes to outline the ore bodies and develop mining plans. This paper will discuss our optimization results of both the selective flocculation and the cationic silica float as applied to our various ores. In addition the pilot plant studies and drill core testwork will be discussed.

Jan 1, 1978

By Jorge Blázquez, Pablo Ravanal, Paulo Couceiro, Juan Navarro

Blasting performance is influenced by rock mass properties and blast design parameters. From them, the rock is the only variable that cannot be modified, but it can be measured, so that, blast design variables can be adapted to optimize the results. A new methodology to assess rock mass quality from drill-monitoring data from both autonomous and manual rotary drilling modes is described to guide blasting in open pit operations. For that, a thorough normalization process has been developed to minimize external influences induced in the data by the rig system for autonomous mode and by the operator intervention for manual mode. Principal component analysis has been used to combine MWD information. Two rock description indexes are derived directly from Measurement While Drilling (MWD) data collected. The first index is a Structural factor that classifies the rock mass condition in three classes (massive, fractured and heavily fractured). The second index is a Strength factor that classifies the rock according to the strength properties. Both indexes have been combined to obtain an overall drilling rock factor along the hole. This has been named by the authors as the X-Rock model.

Feb 6, 2023

By Nilmara Dias, Maria Margarida Martins, Maria Teresa Carvalho

"The heavy residual fraction of the mechanical and biological treatment (MBT) plants treating undifferentiated municipal solid waste is mostly composed by inert materials, such as glass, stones, ceramics and brick. Glass, appearing in significant grade and amount, is not recycled today due to the high content in the other materials, mainly stones. All these materials have approximately the same density but stones have significantly different shape from other materials particles. In this paper it is presented the research developed to eliminate stones appearing in the fine fraction (2.8-8 mm) of the MBT plants heavy residual fraction (MBTr) using a shaking table operated in dry conditions. Two different samples from two different MBT plants were used. Firstly, the samples were characterized (materials content and particle size analysis). Then, laboratory work was carried out to optimize the operation of the shaking table, by changing the machine parameters, deck slope and movement frequency. The study showed that it is possible to upgrade the product in glass. The best results, obtained with one single stage of processing, were 82% content in glass with 84% in recovery, in the glass concentrate, when the coarser fraction (-8+5.6 mm) of one of the MBT plants was used. With the intermediate particle size fraction (-5.6 + 4mm), the glass concentrate attained 74% content in glass with 91% recovery."

Jan 1, 2014

By John L. Shafer

Often an in situ leach is the only practical economic method for copper recovery from small low grade oxide deposits. The decision to develop a copper property by an in-situ blast and leach is strongly dependent on ore grade, tonnage, hydrology, and the copper extraction and acid consumption rates. The inherent "leachability" of the ore will in part determine the desired amount of fracturing of the ore deposit by the blast in order to obtain a copper extraction rate that is economical. For the last several years Occidental Research Corporation (ORC), the corporate R&D for Occidental Petroleum has under-taken a modest effort to address the question of "how to best identify and determine the information necessary to predict and control the operation of an in-situ leach for the economic recovery of copper."

Jan 1, 1977

By R. G. Hilton

This paper deals with application of Super Detox? stabilization technology to the treatment of electric arc furnace dust (US-EPA listed hazardous waste KO61 ). The process has been used on approximately 170,000 tons of electric arc furnace dust. In addition to the nearly four years of commercial experience at Sterling, Illinois, the process is now being permitted for application at two other locations. The process was originally developed by the Bethlehem Steel Corporation and then further improved by Conversion Systems, Inc. (Bethlehem Steel&apos;s Licensee). The treatment process offers many unique bases for its selection, including: A) Low cost compared to the treatment alternatives; B) Lowest available TCLP leachate levels for any process treating K061. Many other processes leave some residue that represents a disposal requirement, although often not addressed; C) Produces minimized final waste disposed, including the fact that the total volume of dust generated and less than the volume occupied by the residue slag from HTMR; and, D) Opportunities for the beneficial utilization of part or all of the waste stream through the development of chemical and physical characteristics. Each of these aspects will be specifically discussed in the paper, including that status of the operations now under permit.

Jan 1, 1994

By V. M. Bystritsky, M. G. Sapozhnikov, G. M. Nikitin, A. B. Sadovsky, Yu. N. Rogov

"At present kimberlite ore is processed in crushers or grinding rolls with subsequent grinding in wet mills down to a size of 0.2 mm. The basic disadvantage of the standard diamond processing technology is that crushing kimberlite ore can damage the most valuable large diamonds of few carats. Tagged neutron method offers a possible solution to this problem. It allows detecting diamond inside kimberlite ore without its disruption. The results of the tests of the neutron separator prototype carried out at the Lomonosov processing factory of PJSC Severalmaz are discussed. The possibility to detect the diamond in the rock whose size is 10 times larger than the size of the diamond is demonstrated.INTRODUCTION At present standard diamond processing technology implies disintegration of kimberlite ore in crushers or grinding rolls down to a size of 0.2 mm. It inevitably leads to high probability that large and most valuable diamonds could be damaged. The fraction of diamonds which lost integrity in the process of ore enrichment could be as large as 35-65% [1]. Tagged neutron method (TNM) [2] offers a possible solution to this problem. It allows detecting diamond inside kimberlite ore without its disruption. The main idea of the TNM is irradiation of an object by fast 14.1 MeV neutrons from binary nuclear reaction d + 3H ?4He + n (1) and detecting (tagging) the 4He (a-particle) that accompanies neutron. That gives possibility to determine direction of the neutron momentum. Those tagged neutrons irradiate kimberlite ore under investigation and produce gamma rays via inelastic scattering reactions with nuclei"

Jan 1, 2018

By M. Kul

In this study, the effects of various extraction and stripping parameters, such as equilibrium pH (7.0, 8.5 and 10), extractant concentration (5, 10 and 20 volume %), organic-to-aqueous (O/A) ratio and stripping agent type and concentration were studied on chromium (VI) recovery from chromium electroplating rinse bath wastewater using Aliquat 336. Results showed that these parameters all had significant effects on chromium (VI) recovery. A pregnant strip solution from a chromium electroplating rinse bath wastewater with 33.4 g/L chromium content, suitable for sodium dichromate production, was generated by 20 vol. % Aliquat 336 in commercial kerosene. The O/A ratio was 1/4 and the equilibrium pH value was 0.87, the as-received pH value. The wastewater was treated with a two-stage countercurrent extraction process to produce a loaded organic phase, which was later stripped at the O/A ratio of two with a 4-M NaOH solution in a two-stage countercurrent stripping process using Taguchi?s optimization technique.

Jan 1, 2010

By T Elkington, A Finch

The theory of constraints (TOC) is a business improvement method that focuses on exploiting a business’s bottleneck to deliver the highest possible profit. Early applications were mostly in the manufacturing industry; however, the theory in itself is completely generic and has now been applied widely in other industries such as services, retail, software and distribution, amongst others. The intent of the approach is attractive – it focuses on the ‘silver bullet’ rather than ‘death by a hundred projects’, and it focuses on growth rather than cost cutting. Application within the mining industry has been limited to date, although there are a few applications emerging. This paper discusses how TOC can be applied to maximise value during the project planning phase and how to maximise profits when the mine is operational. The paper uses two case studies to illustrate the approach. Case study 1 uses the approach to improve tactical mine planning, which delivers an increase in revenue of 58 per cent. The second case study is a strategic mine planning example that delivers an increase in value of 77 per cent.CITATION:Finch, A and Elkington, T, 2014. Application of the theory of constraints to strategic and tactical mine planning, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014 , pp 129–136 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

By V. Panayotov, M. Panayotova, R. Villas-Bôas

The "United Nations Framework Classification (UNFC-2009) for Fossil Energy and Mineral Resources 2009” is the international system designed to meet (to the extent possible) the needs and to support the decision making and resources management of private industry investment, governments, policymakers, bank investment, scientists. There are different international and national systems classifying commodities (resources, reserves, possibility and feasibility to extract them, etc.) with their own definitions and reporting terminology which often do not overlap entirely or even differ significantly - thus creating difficulties and problems among stakeholders to understand each other. The UNFC-2009 is developed to allow “speaking in one language”. The paper presents briefly the UNFC-2009. The UNFC-2009 applies simultaneously three fundamental criteria to classify projects: economic and social viability, field project status and feasibility, and geological knowledge (so called E, F and G axes), thus creating a visualized, easily understandable three dimensional system. The E, F and G axis categories are divided to subcategories, using additional criteria. The UNFC-2009 is already applicable to solid minerals, nuclear fuel resources, petroleum. The amounts of solid waste generated by metals production from ores (mining, minerals beneficiation, extraction metallurgy) and its metals content are discussed from the viewpoint of using the waste as resource. An attempt is made to apply the UNFC-2009 to technogenic waste from metals production from ores - both to old engineering constructions (historic mining dumps and reclaimed beneficiation tailings ponds) and new (currently in use) dumps and ponds.

Jan 1, 2016

By Larissa Koroznikova, Steve Durkin, Bradley Drake, Michael Tuck

This paper presents the results from the investigation of the application of thermal fragmentation in Australian hard rock underground narrow-vein mining. Two geologically similar samples from an underground narrow-vein hard rock gold mine were collected to obtain a measure of the technology’s ability to recover ore by the creation of large thermal openings to assess the applicability of the thermal method. Particle size distribution showed a higher generation of fine product, − 2 mm, by thermal fragmentation compared with selective blasting by 31%. The Bond work index for thermal ore (12.62 kWh/t) is half to that of the blasted ore value (25.32 kWh/t). The average grindability obtained for the thermal ore sample was greater than the blasted sample by a factor of 2.44, a higher value indicating a decrease in the energy required to grind. The thermal fragmentation method generates product with higher dissolution of gold in cyanide, by 14% for the − 9.5 + 2 mm size fraction samples. Additionally, the thermal fragmentation results in higher production of − 9.5 + 2 mm material by 15 % compared with selective blasting.

Thermal pretreatment can significantly improve industrial comminution operations by reducing energy requirements and increasing mineral liberation. The effect of pretreatment using conventional and dielectric heating followed by quenching on the fracture properties of a number single and multiphase brittle materials has been investigated. The reduction in the impact fracture energies and particle strengths with and without pretreatment has been measured in precise single-particle experiments using the Ultrafast Load Cell. Variations in the fragmentation pattern caused by different pretreatments were assessed by measurements of the progeny size distributions. The differences in the effect of thermal treatment on single and multiphase materials are discussed based on the experimental results.

Jan 1, 1995

By Keith M. Axler

This report addresses issues specific to the generation of hydrogen fluoride via reaction of calcium fluoride with sulfuric acid. This process has been established on a commercial scale and is under consideration for treatment of calcium fluoride residues from uranium processing. Magnesium fluoride slags are also available as a product of uranium processing. The technique of using sulfuric acid for the production of hydrogen fluoride from magnesium fluoride is also under consideration as a residue processing scheme. In the current study, thermodynamic modeling was used to investigate these chemical processing systems. The results presented herein reveal information relevant to the selection of processing temperatures and conditions. Details include predicted effects in system composition based on operating temperatures for both the calcium fluoride and the magnesium fluoride systems.

Jan 1, 1996

By William M. Turner

Thermonics is a methodology of ground-water flow system analysis based upon the distribution of heat within the subsurface as influenced by moving ground water. Thermonics is based upon the Stallman Equation 1 (1) which describes the simultaneous transfer of heat through a porous medium which contains moving ground water. The Stallman Equation is:

Jan 1, 1980