Search Documents

By V. B. Dale

This paper is one of a series covering the mineral resources of the Nation. It briefly describes most of the known tungsten deposits of New Mexico. Most of the descriptions are from field examinations by the senior author. Reported tungsten occurrences that were not visited are listed below: Colfax County: Occurrences of ferberite in thin veins in Willow Creek near Elizabethtown.4/ Dona Ana County: Small, low-grade occurrences of scheelite near the summit of the Organ Mountains about 15 miles east of Las Cruces. Hidalgo County: Scheelite reported in the Daisy mine 7 miles southeast of Hachita. Ores are carbonates containing copper, gold, silver, and bismuth.5/

Jan 1, 1959

By John H. Hild

This is a report on work done and results obtained in a minerals exploration program conducted by the Bureau of Mines on the lead-zinc deposits in the Ross Basin-Lake Como district, San Juan County, Colo., in 1948, 1949, and 1950. Four large veins--the Seven Thirty, Red Rogers, Cashier-Shorts top-Canandaigua, and Queen Anne--and several narrow spur veins were explored at relatively shallow depths with core-drill holes. Thirty-nine holes, totaling 10,491.5 feet, were drilled, and the core samples were assayed at the Bureau of Mines station at Salt Lake City, Utah.

Jan 1, 1959

By R. J. Leary

The natural gas-air burner described in this report was designed and constructed to meet the thermal requirements of a convective process for heating steel scrap. This process involved downward combustion of natural gas with air, blending the combustion products with diluent air, and then passing this tempered stream of gases downward through a porous bed of steel scrap contained in the furnace chamber. The scrap would be heated to a temperature limited by the adiabatic flame temperature of the gas stream in a period that depended on the rate at which heat was supplied per unit of bed cross section. The temperature of the gas stream would be limited to that beyond which an objectionable degree of oxidation would occur; for carbon steel this limit had been found to vary from 1,900° to 2,100° F. with the superficial velocity of the gas stream. The productivity of the process was dependent on the rate of heat input per unit of furnace cross section; for the 3-foot-diameter experimental furnace an input of 680,000 B.t.u. per hour was desired. The burner described was designed to meet these conditions of temperature and heat input. It provided for three streams of entering gases: (1) A primary air-fuel mixture too rich to be combustible, that is, above the upper flammable limit; (2) secondary air for combustion of the primary mixture; and (3) tertiary air, principally for cooling the combustion products to the temperatures desired for process operation. Downward combustion of the primary and secondary streams occurred in a flame stabilized on an annular port, while tertiary air flowed in an annular path surrounding the port and also through an axial channel whose wall formed the inner ring of the annular port. This burner performed beyond the designed heat-input rates while producing stable flames, which were adjusted readily to the temperatures desired. Gas-stream temperatures were easily controlled to within 15° F. of the desired value by simple manual adjustment of the flow valves.

Jan 1, 1959

By John J. Mulligan

Since 1941 the Federal Bureau of Mines has been conducting an intermit-tent program of placer and lode investigations to evaluate the potential tin resources of the western Seward Peninsula tin belt. Previous investigations were made in the Potato, Cape, Brooks (Lost River), and Ear Mountain areas. As part of this program the Bureau made a reconnaissance of reportedly tin-bearing stream gravels in areas adjacent to the previously worked tin deposits at Lost River and Potato Mountain. The objective of the reconnaissance was to determine if additional areas might be favorable for lode or placer exploration. The work was begun late in the fall of 1956 and completed during the following summer. The streams sampled were the Lost River and York Creek in the Brooks Mountain area and the Anikovik River and Kigezruk and Baituk Creeks in the York area. Samples were obtained by churn-drilling methods employing conventional placer-evaluation procedures. Holes were drilled at wide intervals at sites chosen as being representative of drainage areas rather than of individual gravel deposits. Minor to trace amounts of tin were found in the gravels of all these streams, but the highest grade was 0.35 pound of tin per cubic yard in the gravels of Lost River below the mouth of Tin Creek. Small amounts of gold were found on Baituk Creek and in one hole on the Anikovik River; the highest grade did not exceed 10 cents per cubic yard. Traces of scheelite and barite were found on York Creek, chromite was encountered in one hole on the Anikovik River, and minor amounts of titanium minerals (probably derived from basaltic intrusives) were found in the York area.

Jan 1, 1959

By Van E. Shaw

Three comparatively simple, efficient, and rapid extraction methods for the dissolution of yttrium and rare-earth elements from a euxenite carbonate residue have been developed, using dilute sulfuric acid as the solvent. Extraction processes have resulted in yields of 98+ percent of the total rare-earth elements and yttrium contained in the residue and have given preliminary separation between the cerium-group and the yttrium-group rare-earth elements. Extraction procedures presented are: Procedure 1. -The recovery of total rare-earth elements and yttrium by a cold dilute sulfuric acid leach at a pH of 2.5. Procedure 2. -The recovery of yttrium and yttrium-group rare-earth elements by leaching with dilute sulfuric acid at 125° F. and a pH of 3.0, with subsequent recovery of the cerium-group rare-earth elements by a cold dilute sulfuric acid leach of the residue at a pH of 2.5. Procedure 3. -The recovery of the total rare-earth elements and yttrium by fractional leaching as in procedure 1, followed by boiling the sulfate solution, which precipitates the cerium-group rare-earth elements and leaves the yttrium-group rare-earth elements in solution.

Jan 1, 1959

By H. W. Sohns

A retort was constructed in which fine particles of shale, entrained in steam or other gaseous media, could be retorted at controlled temperatures and residence times and the effects of retorting variables upon quality and quantity of products could be determined. Studies of the effects of temperature upon products obtained from Green River (Piceance Creek Basin, Colo.) and Chattanooga (Tenn.) oil shales were completed. The feasibility of using the retort to process a shale of extremely high moisture content from Brazil also was investigated. Air was used as the entraining medium in a series of studies in which combustion of some of the products of retorting within the retort tube supplied a major portion of the process heat. In another series, shale oil from a conventional retort was cracked thermally to obtain data for comparison with results of retorting en-trained shale. In still another series the effects of rates of steam flow and solids feed upon rates of heat transfer from the furnace to the process stream were studied. Crushed quartz rather than oil shale was charged to the retort in this series. A study was begun in which raw shale was partly retorted, the products separated, and the partially retorted shale recharged to the retort. The shale was to have been recycled until it was completely retorted in an effort to improve oil yield by recycle retorting; however, the project was terminated before the investigation was completed.

Jan 1, 1959

By R. E. Lindstrom

A study of ion-exchange resin crosslinkage and eluant flow rate, resin-bed shape, and addition of separating ions to feed stock was undertaken to determine their effect on the separation efficiency of ion-exchange on bastna-site-rare-earth elements. Results show that 12-percent divinylbenzene (DVB) crosslinkage resin is detrimental to separation efficiency at flow rates over 2 to 5 ml./min./sq. cm.; whereas, separation with 4-percent DVB crosslinkage resin is relatively unaffected by flow rates between 2 and 10 m1./min./sq.cm.

Jan 1, 1959

By B. W. Naugle

This report describes the carbonizing properties of coals from the principal beds in Cambria County, Pa. Samples of coals from Upper and Lower Freeport and Upper and Lower Kittanning beds having estimated minable reserves of 50-million tons or more were studied by the Bureau of Mines. Cambria County coals rank either as medium-or low-volatile bituminous. A preparation study indicated that all coals tested in this county, except one sample from the Lower Freeport bed, were responsive to cleaning and would yield a product with satisfactory chemical properties for metallurgical coal. All coals tested from Cambria County yielded strong coke; however, they expand excessively when carbonized singly, and should be used only as minor constituents in metallurgical coking blends when carbonized in slot-type ovens.

Jan 1, 1959

By Farrel W. Lytle

Instrumental analysis has become an indispensable tool in research and production of the rare-earth elements. This development can be attributed mainly to a combination of two factors--the marked chemical similarity of the rare-earth elements, which excludes classical methods of analysis, and the speed and accuracy of instrumental-analysis techniques. With continued improvements in methods of producing high-purity rare-earth elements, keeping pace instrumentally is becoming much more difficult. Accordingly, greater emphasis is being placed on improving instrumental limits of detection and accuracy. The methods employed most frequently for determining impurities in rare-earth elements involve use of the optical-emission spectrograph (3, 4)4/ and the spectrophotometer (9). Although numerous X-ray-emission spectrographic methods (6-8) have been developed for analyzing rare earths, these techniques have not included detection of low-level impurities. This investigation was conducted to find the precision and accuracy of X-ray fluorescence in deter-mining impurities in rare-earth oxides in the 0.01-to 1.0-percent-concentration range.

Jan 1, 1959

By W. H. Oppelt

A lignite from west-central North Dakota (Mercer County) was dried by the Bureau of Mines by the Fleissner process at saturated steam pressures to 1,500 pounds per square inch absolute (p.s.i.a.). Normally, the process is operated at pressures of 200 to 370 p.s.i.a. At the highest pressure the temperature of the saturated stearn is 596° F. The purpose of the investigation was to evaluate the influence of very high stearn pressure and temperature on moisture removal, steam consumption, and physical and chemical characteristics of the dried lignite. Two drying cycles were used: A normal cycle, corresponding to previously established standard time requirements, and an accelerated cycle, wherein time requirements were determined by boiler capacity and handling speed. Blank tests to determine stearn requirements for heating the empty autoclave were performed for each cycle and each test condition. Moisture removal, final moisture content, net steam consumption, and size stability of the dried lignite were determined.

Jan 1, 1959

By J. B. Gayle

Since the turn of this century, there has been increasing interest in the application of flotation processes to the beneficiation of finely divided minerals of various types, This is reflected by the large numbers of papers dealing with various aspects of this problem published annually both in this country and abroad. For the most part, such papers fall into one of three categories: 1. Those concerned with achieving, by various chemical and/or physical means, a set of conditions under which certain particles become potentially floatable while others do not. 2. Descriptive studies of plants and pilot plants effecting separations between such particles. 3. Studies of the effects of certain design and operating variables on the rates and efficiencies with which such separations can be effected.

Jan 1, 1959

By E. A. Magill

This report is one of a series prepared by the Bureau of Mines on manganese deposits of the Northwestern States. It describes properties on the Olympic Peninsula, Wash. Exploration by the Federal Bureau of Mines in 1939-40 and 1954-55 on several typical deposits is summarized, and examination data are presented for other manganese deposits on the peninsula. An attempt was made to list all known occurrences; however, some properties are abandoned, and their exact location is unknown.

Jan 1, 1960

By S. L. May

The Bureau of Mines has developed several methods for extracting tantalum and columbium (niobium) and the rare-earth compounds from ores and concentrates. A cooperative agreement was made by the Bureau with Porter Bros. Corporation of Idaho to process 200 pounds of its euxenite concentrate by methods that had been developed at the Albany, Oreg., Metallurgy Research Center. The euxenite concentrate was processed to extract and purify the valuable metals by chlorination, solvent extraction, and hydrometallurgical techniques. Chlorination was used to convert the valuable constituents into chlorides and to partly separate them. Solvent extraction techniques were used to separate the tantalum from the columbium. The rare-earth and uranium compounds were purified by hydrometallurgical methods.

Jan 1, 1959

By W. L. Heidenreich

This report describes the methods and results of field investigations conducted by the Bureau of Mines between December 1956 and December 1957 on seven deposits of nickel-cobalt-iron-bearing laterite and weathered serpentine near the west coast of Puerto Rico east and south of Mayaguez. These deposits were named, for purposes of identification, Guanajibo, Punta Guanajibo, Las Mesas, north and south deposits of the Rosario Southeast group, and the west and east deposits of the Maricao Southwest group. In addition, the lower 17 miles of the Guanajibo River Valley was tested at widely spaced intervals for possible concentrations of magnetite and chromite in the alluvial sands. The objective of the investigations was to appraise, by drilling and sampling, the two largest deposits--the Guanajibo and Las Mesas. Testing of the smaller deposits was much more restricted. Field investigations consisted of mapping, drilling with power auger, sampling drill-hole sections, and pre-paring samples for chemical analyses, mineralogical studies, and metallurgical tests. The work was financed jointly under a cooperative agreement by the Bureau of Mines and the Economic Development Administration, an agency of the Puerto Rican Commonwealth.

Jan 1, 1959

By H. C. Carpenter

Data are presented comparing results obtained with 17 different catalysts in hydrogenating crude shale oil to gasoline in single-pass operation. A method is described for predicting the maximum yield of gasoline obtainable at constant pressure for each catalyst from results of a limited number of experiments at different temperatures. Operating variables have considerable influence on yields and properties of products. With most of the catalysts, at operating temperatures below 890° F. liquid yield exceeded 100 volume-percent. Above this temperature the volume of liquid product decreased rapidly. Maximum gasoline production in most instances was achieved at a temperature higher than that at which the maximum volume of liquid product was produced.

Jan 1, 1959

By John B. Goodman

This report summarizes the work done by the Koppers Company, Incorporated, in cooperation with the Bureau of Mines on the commercial evaluation of the primary low-temperature tars produced from Texas lignite in the Rockdale, Tex., plant of the Aluminum Company of America in conjunction with the Texas Power and Light Company. The interest of the Bureau of Mines in this project is twofold. First, through its cooperative agreement with the Texas Power and Light Company the Bureau has assisted in the technical design and practical operation of the prototype, externally heated, entrained-state carbonizer for producing char for electric-power production and for primary low-temperature tar. Second, the first successful operation of the prototype carbonizers employing the Bureau of Mines-Parry process on lignitic coal in 1953-54 led to the production of large quantities of primary lignitic tar, concerning which too little was known or had heretofore been published in this country.

Jan 1, 1959

By M. R. Geer

Traditionally, fine coal is more troublesome than the coarser sizes at every step of the coal-preparation process--screening, cleaning, dewatering, and drying. Therefore the present trend toward a higher proportion of fines in the run-of-mine product, brought about by changes in mining practice necessitated to increase productivity, has added greatly to the task of preparing coal for the market. One of the more difficult and costly problems involved is that of recovering fine solids from the washery water. These fine solids should be recovered in the interest of conservation, and they must be removed to provide recirculating water of proper quality. If there is a plant effluent, it must meet increasingly stringent requirements against stream pollution. Vacuum filtration has been used for years at a few plants to recover the extreme fines, but its additional cost discouraged general adoption until recently. Now, with growing emphasis on better solids recovery, filtration is becoming more widespread. Many coal slurries filter readily, giving high cake rates and clean filtrates. Others, however, particularly those containing either a high proportion of material finer than 200-mesh or an appreciable amount of clay, are much more difficult to filter. Many of these refractory slurries can be rendered more filterable by flocculation. A previous report of Bureau of Mines research dealing with flocculation alone was published in 1940.5/

Jan 1, 1959

By J. E. Wilson

The Pittsburgh carbonization laboratory of the Bureau of Mines has determined the expansion or contraction of more than 300 coking coals in a modified Bethlehem-type sole-heated expansion tester. Information on the actions of coals or blends of coals when coked is extremely valuable to operators of commercial-scale coke ovens. Coals that expand abnormally or beyond expectations can cause extensive damage to coke ovens and result in costly shutdowns and repairs. Although test results for many of the coals have been given in various Bureau of Mines publications, considerable information was not published. Thus, it is the purpose of this report to furnish coal operators and the coking industry with a current appraisal of the expanding properties of all coals tested by the Bureau before September 1, 1958. These data should be useful in the normal long range planning of coal and coke production and will be essential if the demand for coking coals increases abnormally or when reserves of higher grade coals are depleted.

Jan 1, 1959

By William J. Campbell

These investigations were undertaken as part of a program to determine the optimum X-ray spectral lines to use for analyzing the wide variety of samples received by the X-ray Laboratory. Theoretical calculations and experimental data derived from these investigations show that longer wavelength spectral lines, > 2A, are very useful for many analytical problems. Because of the low fluorescence yield of the elements of atomic numbers 13-22 and the small depth of penetration of their X-ray spectral lines, these elements were originally considered to be insensitive; however, these studies show that the wide dispersion of their spectral lines, coupled with their weak beta lines, permits the use of wide collimation, thus increasing the line intensity. More importantly, the background due to scattered primary radiation is very low in the long-wavelength region.

Jan 1, 1959

By V. A. Nieberlein

Problems of design involving the high-temperature characteristics of materials of construction have focused attention on tungsten, the metal with the highest melting point. To study the properties of this metal a method was needed to produce tungsten of high purity easily and consistently. The Bureau of Mines has made tungsten metal in massive form on a laboratory scale by hydrogen reduction of tungsten hexafluoride (WF6). Metal made in this manner had a purity of 99.99 percent or better, with reference to all detectable impurities, including gases. The process tolerated a wide variation in operating conditions, and the results with respect to total impurities as low as 0.01 percent were reproducible.

Jan 1, 1959