Search Documents

By E. C. Baker

The capital investment and operating costs of two methane-control systems used during longwall mining operations are compared in this Bureau of Mines report. Costs are given for a surface gob hole drainage system and an underground cross-measure borehole drainage system to control methane gas in gobs in four coal mining areas--central Pennsylvania, northern West Virginia, southern Virginia, and northern Alabama. Present-worth analysis is used to determine the more cost-effective alternative in each location. The alternatives have equal lives and provide the same service based on a minimum rate of return of 15 pet. In central Pennsylvania and northern West Virginia, the gob hole system is more cost effective than the cross-measure system, by 10 and 18 pet, respectively. In southern Virginia and northern Alabama, the cross-measure system is more cost effective, by 29 and 38 pet., respecitively. Costs for other locations must be developed on a case-by-case basis.

Jan 1, 1988

By Deno M. Pappas

The objective of this Bureau of Mines investigation was to identlfy and evaluate alternative binder materials for use in stabilizing and consolidating highly fractured roof along longwall faces and gate roads. The desirable characteristics of a stabilization material were defined, and an extensive search was conducted to find materials satisfying these characteristics. Of 20 materials originally scrutinized, 9 were chosen for laboratory analyses. The laboratory tests evaluated bond strength and tensile strength under both dry and wet conditions. An optimum material was not found. The laboratory analyses indicated two possible candidate materials for longwall stabilization: high-aluminous cement and two-component epoxy; however, the tensile strength of the high-aluminous cement was mediocre, and the epoxy cement is toxic, flammable, and fairly expensive. The potential market demand for an effective and economical stabilization macerial is discussed in the appendix.

Jan 1, 1988

By Elizabeth G. Baglin

Research was conducted by the Bureau of Mines to determine the feasibility of using electrokinetic densification to dewater Bayer process red mud, magnetic black mud prepared by pressure digestion of red mud in the presence of ferrous sulfate, and magnetic black mud formed by simu-lated Bayer digestion of Jamaican bauxite with added ferrous sulfate. Tests showed that the solids content of presettled muds could be increased from 25 pct to approximately 40 to 48 pct by gravity draining followed by electrodewatering for approximately 48 h. Electrodewatering may not be practical because of increased reagent and processing costs and because the muds must be thoroughly washed prior to electrodewatering to remove dissolved ions and decrease mud conductivities.

Jan 1, 1988

By Thomas M. Barczak

he stiffness characteristics of longwall shields were investigated in this Bureau of Mines study. Since longwall strata activity is characterized by roof-to-floor and face-to-waste displacements, a model with two degrees of freedom was used to describe the load-displacement relationship of the shield structure. The model considers the support as an elastic body and relates horizontal and vertical resultant forces acting on the support to associated displacements as a function of the stiffness of the support structure. Stiffness coefficients under full canopy and base contact configurations were determined by controlled displacement loading of longwall shields in the Bureau's Mine Roof Simulator (MRS). Three two-legged longwall shields of different manufacture were investigated. The stiffness characteristics of these shields were evaluated relative to two parameters, namely, shield height and setting pressure. The test results indicate a reduction in shield stiffness for increasing height. Setting pressure was found to have less of an effect on shield stiffness, producing only a slight increase in stiffness as setting pressure increased. Similar trends were observed for all three shields, indicating a similarity in stiffness characteristics for shields of the same basic configuration.

Jan 1, 1988

By N. Greninger

The Bureau of Mines conducted a laboratory study of the measurement of the water and rock dust (RD) contents of synthetic mine-type coal dust (CD) mixtures using a commercial unit for measuring water content and several prototype radiometric units for measuring the RD content. The RD content ranged from 50 to 100 wt pct and the added water (AW) ranged from 0 to 15 wt pct. The total water (TW) content (intrinsic (IW) and AW) of a small dust sample could be readily measured automatically by essentially untrained personnel using a commercial unit. The RD content of a sample containing only IW could readily be measured by moderately trained personnel using several radiometric units. With gamma-ray devices, about 300 g of sample is needed. With the improved beta-ray device, about 25 g of sample is needed. With dry mine dust samples, the estimated RD error range for gamma-ray devices is 0.8 to 2.3 pct and 0.5 to 1.0 pct for beta-ray devices. However, the radiometric measurement of RD content was questionable if the dust mixture also contained AW or if it was uncertain whether the dust mixture contained AW.

Jan 1, 1988

By W. R. Wrzensinski

This report presents the findings from a l-yr Bureau of Mines program in which sulfur concrete reinforcing materials were tested and evaluated to determine their resistance to corrosion. It also summarizes the permeation characteristics of sulfur concrete and the exemplary performance of precast, reinforced sulfur concrete structures in various industrial environments. The Bureau is furthering the development of sulfur concrete technology as part of a larger effort to find uses for the Nation's plentiful sulfur resources in construction materials. Sulfur concrete is a corrosion-resistant material that can be used in acid and salt environ-ments where conventional materials fail. Penetration of corrosion-inducing agents is minimized because of the low permeation characteristics of sulfur concrete.

Jan 1, 1988

By Daryl R. Tweeton

The Bureau of Mines is investigating possible applications of geophysics to monitor leachate during in situ mining. Tomographic reconstruc-tion of seismic or electromagnetic crosshole data appears applicable. The tomographic program BOMTOM (Bureau of Mines tomography) was written and then used to investigate reconstructions with synthetic travel time data. The calculations confirmed that without constraints, crosshole data do not provide unique solutions. The solution is not determined solely by the data, but is also influenced by the velocity guesses starting the iterative solution procedure. The effectiveness of constraints in combatting nonuniqueness was examined. The requirement that the velocity not vary laterally at the top and bottom of the pixel grid was effective. This constraint is realistic when the top and bottom of the grid represent dry and saturated re-gions, respectively. Limiting the maximum velocity improved reconstructions, but may not be applicable in practice. BOMTOM uses the simultaneous iterative reconstruction technique (SIRT) with straight ray paths. The program is efficient in use of memory, and can be run on a personal computer. A source code in FORTRAN is listed. A source code in BASICA and compiled executable codes in both languages are available from the Bureau's Twin Cities (MN) Research Center.

Jan 1, 1985

By Thomas M. Barczak

The effect of load rate on the load-carrying capabilities of wood cribs is investigated in this Bureau of Mines study. The modulus of deformation (stiffness) of wood crib blocks has been shown to increase with increases in rates of load application, causing larger load reactions for increases in convergence rates. Since wood cribs are tested in the laboratory at convergence rates that are orders of magnitude faster than typically would occur underground, wood cribs tested in the laboratory will react larger loads than the same cribs would react underground for the same displacement. Tests conducted in the Bureau's mine roof simulator on green wood crib blocks indicate that the increase in stiffness for increasing load rates diminishes at displacement rates beyond 0.1 in/min, making crib load nearly independent of load rate for rates faster than 0.1 in/min. Seasoned wood specimens were not as con-sistent in load-rate dependency. Some possible explanations of observed load-rate behavior on wood crib specimens are also postulated in this paper.

Jan 1, 1988

By J. H. Stears

Increasing use of Birmingham and other roof trusses prompted a Bureau of Mines study of support forces produced on a mine roof by these members. Equations, obtained from laboratory and field tests, are given for calculating the contact forces between the roof strata and a typical truss. Actual contact forces for a specific truss are difficult to estimate because of variable friction loss at the contact points. A finite-element analysis, using typical contact forces, indicated that trusses have a negligible effect on the stress field in massive, competent roof strata. The effectiveness of trusses in supporting broken rock strata was not analyzed. However, experience has shown that trusses are effective in supporting incompetent roof.

Jan 1, 1988

By P. J. McDonough

The Bureau of Mines designed and tested a hardware-software system for measuring on-line corrosion rates of materials in a rod mill in operation. Currents ranging from 10-6 to 10-3 A and potentials in I-mV increments were converted to a digital signal. The digitized data were frequency-modulated and transmitted from a rotating ball mill to an FM receiver, where they were decoded by computer and then processed in real time using assembly language software. This design approach would allow accurate measurement and control of systems where signals of small amplitude and large ranges are present.

Jan 1, 1988

By J. I. Paige

The effect of fluoride inclusions on the properties of titanium produced from the Bureau of Mines developed induction slag melting process is of concern to members of the titanium industry. The objective of the research was to determine the effect of CaF2 inclusions on the properties of titanium and its survival rate during melting. The data were obtained from single induction-slag-melted ingots prepared with the normal addition of 4 pct and also with 2- and 1-pct additions of CaF2 slag. The results of this effort showed that the mechanical properties of single-induction-slag-melted Ti-6Al-4V alloy exceed the minimum values specified in Aerospace Materials Specification for Titanium Alloy Bars and Forgings AMS4928H, but these materials are much more notch sensitive in fatigue than normal Ti-6A1-4V alloy titanium. First and second vacuum-arc remelts of single-induction-slag-melted ingots fragmented and increased the number of inclusions, while reductions in the amount of flux resulted in an upward trend in the spatial distance between pores in an x-y plane.

Jan 1, 1988

By A. E. Raddatz

Previous Bureau of Mines research has shown that tungsten ores containing as little as 40 pct W032-can be processed by a high-temperature molten-salt extraction technique to produce a tungstate-bearing sodium chloride phase with 99 pct W recovery and little impurity contamination. The objective of this work was to demonstrate that the tungstate-bearing sodium chloride phase can be a suitable feed material for preparing am-monium paratungstate (APT) by a modification to the present industrial solvent extraction process. A combined crossflow-count·ercurrent flow solvent extraction technique to extract tungsten is presented. APT produced by this new technique contained 88.6 pct W032-and the following impurities, in percent: Mn02_ 0.0007, Mo02 0.017, P205 <0.010, and Si02 0.012. Implementation of this processing technique would improve tungsten recovery from concentrates and simplify processing operations.

Jan 1, 1988

By A. E. Isaacson

Bureau of Mines researchers developed and tested equipment to measure corrosion rates on a commercial scale mill. Bench-scale experiments were designed for duplicating ore grinding conditions closely enough so that realistic rate determinations could be made in laboratory tests. Rates measured in a laboratory system compared favorably with those measured in the field. Cast steel was found to have corrosion rates in a copper mill and laboratory test cell of 22 and 21 mpy, respectively. Corrosion was found to account for less than 5 pct of the total grinding media wear in the operations studied.

Jan 1, 1988

By G. L. Hundley

The Bureau of Mines has devised a procedure to recover chromium chemicals from concentrates derived from low-grade domestic chromites. These domestic chromites contain silicon and aluminum impurities at levels that are too high to permit processing by present industrial processes. The Bureau procedure consists of reacting chromite with molten NaOH under oxidizing conditions to form sodium chromate (Na2Cr04)&apos; The reaction product is leached with methanol to recover the majority of the unreacted NaOH, then with water to extract the Na2Cr04 and the remainder of the NaOH. The Na2Cr04 product is recovered by evaporative crystallization from the aqueous solution. This report presents laboratory results of studies to determine the optimum leaching conditions for the reaction products of several domestic chromite concentrates. Results of solution purification and crystallization studies are also presented. The concentrates are from a variety of sources including the Stillwater Complex in Montana, Red Bluff Bay and the Kenai Peninsula in Alaska, and a Ni-Co laterite from southern Oregon. Sodium chromate crystals were produced that contained less than 0.01 pct NaOH.

Jan 1, 1988

By Thomas M. Barczak

The Bureau of Mines is conducting research to optimize the capability of mine roof supports so that the selection and design of these supportsare compatible with the conditions in which they are to be employed. This report describes a study that investigates three parameters influencing the load-carrying capability of wood crib supports: height, configuration, and horizontal displacement. Four crib heights, four parallelogram configurations, and three ratlos of horizontal-to-vertical displacements were tested on full-scale wood crib supports in a mine roof simulator. Test results indicated a reduction in load-carrying capability for increases in crib height. Increasing the contact area by changing the intersecting angle between crib blocks to form parallelogram configurations provided a slight increase in load-carrying capability for the first 10 to 12 in of vertical convergence, after which the cribs became more unstable, resulting in significantly less load-carrying capability. Horizontal displacements did not appreciably affect the load-carrying capability of wood crib supports for the range of vertical displacements (less than 10 in) likely to be encountered underground. This report documents these tests and postulates some explanations of failure mechanics for the observed behavior.

Jan 1, 1988

By Martin Hertzberg

This Bureau of Mines report analyzes diverse observations of the rates and mechanisms for the pyrolysis and devolatilization of coal and polymethylmethacrylate (PMMA). New data are presented for PMMA, together with new morphological evidence for the microscopic structure of the pyrolysis and devolatilization wave front in coals. It is concluded that there is no substantive evidence to support the traditional viewpoint that the pyrolysis and devolatilization rate process occurs isothermally, under chemical rate control; or is described realistically by a classical, unimolecular Arrhenius function of temperature. Instead, the reaction process occurs as a highly nonisothermal, heat-flux-driven, pyrolysis and devolatilization wave front, whose speed of propagation is predictable by internal heat transport constraints. Except for the complication of its charlayer residue, whose increasing thickness insulates the pyrolysis wave front from the heat source flux that drives it, both coal and PMMA behave similarly during pyrolysis and devolatilization. For PMMA, decomposition occurs at a temperature of 3500 to 5500 C; for coal it occurs at 4500 to 6000 C. There is no evidence that the reactant temperature ever exceeds those values regardless of the source temperature to which the samples are exposed.

Jan 1, 1988

By Hamid N. Maleki

Cooperative efforts by the Bureau of Mines and Agapito & Associates, Inc., Grand Junction, CO, achieved the research objective of showing that data from measurements of the rate and change in rate of mine roof movement can be effective in detecting roof instability. Several instruments and techniques have been used to monitor roof movement and to detect imminent roof caves during pillar robbing. Early detection of unstable conditions can provide time either to withdraw personnel and equipment or to allocate supplemental support to prevent injury or down-time. Critical convergence rates were determined both manually and electronically. The detection of critical rate of movement has been shown to be an effective tool in ground control efforts.

Jan 1, 1988

By C. M. K. Boldt

The Bureau of Mines surveyed waste disposal sites at 18 metal and non-metal mines and conducted laboratory and full-scale field tests to de-termine the effects of tailings deposition techniques on physical properties of tailings pond beaches. Survey data included measurements of beach slopes, descriptions of deposition techniques, and measurements of beach physical properties taken at various distances from the point of discharge. Laboratory tests involved depositing two types of tailings, each with different grain-size distributions, into a settling trough and determining the resultant physical properties of settled materials along the length of the beach. Side confinement and the closeness of the water pool to the point of deposition caused the laboratory results to be inconclusive. Full-scale field deposition tests conducted at the tailings pond of a cooperating mine showed that there were similarities in relationships between exit velocities of tailings slurry and physical properties of the settled tailings on the beach.

Jan 1, 1988

By N. P. Kripakov

The Bureau of Mines has developed a unique new mine design procedure to determine the changing static load distributions imposed on under-ground support structures during the mining cycle. The procedure reduces the complexities associated with analyzing a three-dimensional problem. A combination of the multiple-seam displacement-discontinuity model and a two-dimensional finite-element window model produces refined results for a specific area of interest by assuming displacement compat-ibility between models. Input to the procedure includes the geometry of mined-out areas in up to two adjacent seams, the rock mass characteris-tics of the surrounding geology, the in situ stress conditions, and the mining sequence. The displacement-discontinuity program calculates ex-pected loadings for mine structures affected by the mining cycle and/or by overlying or underlying seams. Pseudoelastic finite-element analysis using a yield-factor approach determines the stability of coal pillars by simulating the degree and extent of nrogressive rib failure and sub-sequent load transfer. Application of the procedure is demonstrated on a field problem. In-duced stress changes predicted from the numerical model analysis are in reasonably good agreement with stress measurements obtained from an instrumented chain pillar affected by remnant workings in an upper seam.

Jan 1, 1988

The Bureau of Mines, in an effort to improve resource conservation, mine planning and development, is currently investigating the loading behavior of pillars in multiple-seam developments. The simultaneous mining of two or more coalbeds may cause instability between room-and-pillar operations resulting in an interaction known as pillar load transfer. Although pillars may be adequately designed for single-seam mining, the development of a second seam may complicate loading conditions in both operations. If pillars are not adequately designed to contend with this load transfer, failure of the mine structure may result. To improve multiple-seam development and pillar design, the Bureau studied the loading characteristics of pillars in three separate multiple-seam operations. In all three cases, instrumented pillars recorded increasing pressure after development of the second seam. Increases in the average pillar pressure ranged from 7 to 110 pct over predicted overburden loads. An analysis of pillar loading before and after second-seam mining indicates that the ratio of overburden to innerburden thickness is a critical factor influencing load transfer. Based on this relationship, safety factors for case study pillars are calculated and alternative design considerations are discussed.

Jan 1, 1988