Search Documents

By Hongxu Li, Zhaobo Liu, Zihan Zhao

A completely new process of selectively recovering Sc3+ without impurity of Fe3+ from Bayer red mud was developed. Prior to water leaching process, red mud needs to be digested and sulfated at a low temperature and subsequently roasted at a higher temperature for a period of time. During the roasting process, the products such as SO2, SO3 and H2SO4 molecules of thermal decomposition of sulfites including NaFe(SO4)2 and NaAl(SO4)2 could be recycled and reused as the raw materials of sulphuric acid. The leaching results indicate that roasting temperature and roasting time are the main constraint on selective leaching performance of scandium. As the sulfated red mud sample is roasted at 750 degrees C for 40 min and subjected to water leaching at 50 degrees C for 30 min, 53.0 wt% Sc3+, <1.0 wt% Fe3+, <0.3 wt% Si4+ and ~8.9 wt% Al3+ could be leaching out. Of note, the solid-liquid separation process is quite easy to be carried out.

Mar 1, 2017

By Brajendra Mishra, Mark L. Strauss, Gerard P. Martins

Nearly the entire worldwide production of europium is recovered, as a minor constituent, from mining bastnäsite, monazite ore, or ion absorbing clays. However, this research indicates a process to recycle europium from waste lamp phosphors as a strategy meet the demand for europium. In this process, waste fluorescent lamp powder is retorted, sieved, leached, and precipitated to produce a mixed europium/yttrium rare earth oxide (REO). Europium is separated from yttrium by selectively reducing Eu(III) to Eu(II) using zinc powder and precipitating europium (II) sulfate from solution using sulfuric acid. Screening experiments were conducted observe the effect of pulp density, precipitation time, entrance pH, and stoichiometric ratio sulfate upon the grade and recovery of europium (II) sulfate. The best conditions to maximize grade and recovery of europium (II) sulfate were a 1 h precipitation time, 10 the stoichiometric ratio of sulfate, 100 g/L mixed REO, and the entrance pH equal to 3. The maximum grade of europium sulfate was 95.93%, and the maximum recovery was 73.32%.

Mar 1, 2018

By Bo Jiang, Jiusan Xiao, Hongmin Zhu, Kai Huang, Shuqiang Jiao

Carbothermal selective reduction of simulative titanium slag and various titanium raw materials were presented and SiO2 was found to be partially reduced, forming a series of Fe-Si alloys during the process. Thermodynamic analysis of the selective reduction between TiO2 and SiO2 was performed using HSC 6.0 software, then a series of equilibrium experiments were designed and presented. The activity of Si reduced from SiO2 was affected by the presence of Fe reduced from FeOx and the generation of Fe-Si alloys, promoting the reduction of SiO2 in the whole process. The results of experiment are in great accordance with the calculated data obtained from thermodynamic analysis.

Jan 1, 2016

By W. H. Cheung

Nickel and cobalt production relies heavily on the processing of nickel laterite ores; these ores contain the majority of known Ni and Co reserves, 80% and 90% ~ 95%, respectively. The Caron process is used to extract Ni and Co metals from low-grade nickel laterite ores (1% Ni and 0.1% Co). It involves selective reduction of NiO and CoO minerals followed by ammoniacal leaching. Despite low metal recoveries, this process continues to be technically and economically reliable and thus commercially important globally. However, keeping the Caron process cost-effective has been a challenge for industries because of increasing economic and environmental pressures. Although studies of the Caron process have been extensive, significant improvements in recoveries of industrial processes have not been forthcoming. Reported industrial metal recovery from high iron content ore is only 80% ~ 85% for Ni and only 40% ~ 45% for Co; recovery is even lower for ores rich in magnesium. The real difficulty here is that there is no complete understanding of and control over the complex series of reactions in the ore and in the leaching solution during processing. Achieving effective metal recoveries from the Caron will require control of the mineral transformations, which affect the activation of minerals by reduction. In this study, the effect of over-reduction was investigated, which superseded the effect of activation by lowering the activity of the minerals and thus metal dissolution. Reduction was carried out in a batch reduction apparatus with 1:1 and 1:2.5 CO/CO2 gas mixtures from temperatures of 500 ~ 700°C and residence times up to 60 minutes. The pre-reduced ores were leached using a standard ammoniacal leaching test. Thermodynamic analysis and possible effects of stable phase field on leaching was examined. The results suggest that control of over reduction effects are directly related to the mineral transformation and reduction conditions.

Jan 1, 2014

By J. G. Stevens, S. W. Colley

"Selective separations of metals and ions in mineral extraction and refining are becoming more challenging as ore bodies become more complex and environmental pressures increase. The separation and containment of mercury produced in gold mining are a factor in the profitability and operability of mines. This paper will discuss the development and implementation of the Johnson Matthey HgFree selective mercury removal process. The process is designed to selectively recover co-leached mercury from either heap leach pregnant solutions at ambient temperature and low mercury concentrations, or electrowinning pregnant solutions at elevated temperature and high mercury concentration, without affecting gold or silver recovery. The process utilizes a highly selective adsorption-desorption step in which mercury is removed quantitatively by the HgFree adsorbent without adsorption of gold, silver or other metals present. Development of the original HgFree adsorbent has resulted in a process whereby mercury can be recovered as an inert salt and is never present as the free metal. The HgFree adsorbent can be regenerated and recycled in situ, and is capable of being reused multiple times. The overall process is compatible with existing gold mining and recovery practices and offers significant environmental and sustainability benefits, including reduction or elimination of the need to retort mercury with a subsequent reduction in potential mercury air emissions. Development of the HgFree adsorbent and process will be discussed along with a pilot operation at two operating mines.INTRODUCTIONMany gold ore bodies contain high concentrations of mercury which when extracted with cyanide, co-extract with the gold and other metals. This mercury is carried through the process with the gold, posing environmental and technical issues when it is separated from the doré. This paper describes a method to selectively adsorb mercury from the gold recovery circuit while it is in a soluble form, leaving gold to be processed as normal. The removal of mercury from the circuit eliminates the need for mercury retorting of doré and so reduces the potential environmental impact of fugitive emissions of elemental mercury."

Jan 1, 2016

By K. L. Gabby

Selective removal of mercury from cyanide leaching solutions while retaining silver has been a long-standing problem, due to the chemical similarity of mercury and silver. In order to be practical, a mercury removal process needs to be both highly selective and use inexpensive materials. This paper reports the use of zinc sulfide (ZnS) as a precipitant for mercury. The mercury cyanide complex (Hg(CN)4 2-) undergoes a replacement reaction with the zinc sulfide, forming insoluble HgS, while the silver cyanide complex (Ag(CN)2 -) remains in solution. Under appropriate conditions, the separation of mercury from silver is nearly quantitative, with close to 100% removal of mercury, while nearly none of the silver is precipitated.

By Reed M. Izatt

SuperLig® materials are capable of individually separating Rh, Pd, and/or Pt in highly purified form (99.95 to 99.99%) from a variety of chloride-based feed streams in a single stage operation. The hydrophillicity and associated kinetics of the supported materials allow for operation at relatively high flow rates of both loading and elution in a packed bed format. Pilot and commercial systems have been operated with Rh, Pd, and/or Pt present in the feed from single digit ppm (mg/l) to tens of g/l. A dual SuperLig® system for one pass Au(CN)2- separation followed by Cu and CN- recovery for CN- recycle has also been tested up to a pilot level,

Jan 1, 1999

By XUEWEN WANG, Xingming Wang, Xuehui Liu, Mingyu Wang

The Panzhihua titanium concentrate contains high contents impurity of Mg and Al, and it is difficult to prepare high grade titanium slag. To solve this problem, a sodium salt roasting-acid leaching process was proposed for removing the impurities in titanium concentrate. Na2CO3 and titanium concentrate were mixed with the proportion of 1:4, and then the mixture was roasted at 700 for 2h. After roasting, the calcine was leached with HCl solution. The experimental results showed that the removal rate of silicon and aluminum can reach more than 85% and 80%, respectively, at leaching temperature of 70 , leaching time of 4h, HCl addition of 5ml and liquid-solid ratio of 4:1.

Jan 1, 2016

By Hylton McWhinney, Doanh Tran, Jewel Andrew Gomes, George Irwin, Sameer Pallavkar, Md Islam, David Cocke, Mohammad Rafiqul Islam

"High-performance nickel-based nanocrystalline zinc oxide adsorbents have been prepared adjusting Ni/Zn mol ratio of 1 :5 by thermal decomposition, coprecipitation and sol-gel method for selective adsorption of thiophene in liquid hydrocarbon fuels at ambient temperature and pressure. To understand the nature of reactive adsorption of thiophene (C4H4S) on Ni/ZnO, the effect of preparation techniques, morphological and textural structure on the desulfurization activity was investigated. A model fuel (20 mL) consisting of pentane (C5H12) and thiophene was prepared and adsorption experiments were performed by a batch method under ambient conditions. The physicochemical behaviors of the fresh adsorbents were obtained using X-ray diffraction (XRD) with EDAX, scanning electron microscopy (SEM). The sulfur concentration in the mixture was monitored by UV-vis spectrophotometry. The adsorption reaction confirmed that ZnO played a crucial role in taking up S element to convert it into ZnS. The deposition of nickel on ZnO is an innovative approach which takes advantage of the selectivity of Ni towards S-species and the high adsorptive capacity of ZnO support.IntroductionLow temperature deep desulfurization of fuels via selective adsorption of sulfur compounds keeping coexisting aromatic hydrocarbons and olefins intact is receiving increasing attention in the research community worldwide in order to satisfy the upcoming environmental regulations and fuel specifications. The sulfur compounds in the transportation fuels is a matter of concern when global crude oil slate is becoming heavier and sourer and environmental restrictions on both the refining process and the refined products are becoming more stringent. According to the current refinery technologies, the sulfur content in refinery fuel is typically around 300-500 ppm by weight (ppmw) [1-3]. Starting in 2006, sulfur limits in highway diesel and gasoline were set to 15 ppm and 30 ppm, respectively. During combustion sulfur in the fuel are converted to toxic sulfur oxide (SOx) and contributes to air pollution and acid rains [ 4]."

Jan 1, 2011

By Ph. Cauwe

This paper presents the experience that NESA and MECHIM have gained about recovery of non ferrous and precious metals from complex sulfide materials. Processed materials are from natural deposits or metallurgical by-products or residues. Roasting of these materials is closely related to the pyro or hydrometallurgical processes used downstream of the roasting. Conditions of a first step of roasting the SELECTIVE ROASTING, are analyzed and explained. The roasted products so obtained are characterised by an extended elimination of volatile sulfides (AS, Bi, Sb, Sn, Pb, Hg, ?? ) and are readily available for the pyrometallurgical recovery of non ferrous and precious metals. After the SELECTIVE ROASTING, thanks to. the high porosity obtained in the "selective calcine", the SULFATE ROASTING is per-formed in excellent conditions. Hydrometallurgical tests performed for the final calcine show a high recovery of non ferrous and precious? metals and require only simple and well known processes. Many experimental and commercial data are given.

Jan 1, 1983

By E. O. Jacobs

A coupled solid and rock fracture mechanics model is used to analyze the blast driven fracture propagation phase, predict propagation rates, and directly measure shockwave and particle velocity. The study incorporates quasi-static pre-stress conditions for different depths below the surface. The scaled experiments include dynamic material properties and quasi-dynamic fracture mechanics which are shown to significantly affect the fracture propagation. The study was performed using three-dimensional cube-type laboratory models fabricated from Polymethylmethacrylate (PMMA). The test cubes are loaded with explosives and resulting fracture networks are studied. The dynamic evaluation of the spatial crack system is monitored using a high speed image camera. An experimental model set-up is designed to indicate the pre-stress effect on deep borehole blasting and is shown that the pre-stress conditions have a decisive influence on fracture profiles and orientation. It is found that shockwaves rapidly exceed the slower dynamic fractures and a majority of cracks occur due to detonation pressure. Experimental testing using different parameters validate that explosive fracturing can predict the outcome of fracture and crack propagation in any rock type with known material properties. This can be accomplished under great stress conditions deep below ground surface. The experimental study results can be applied to a variety of industries such as mining and quarrying, tunneling, oil and gas, and construction.

Feb 23, 2014

By E Forbes, G V. Franks

"This study investigates the dual function of a temperature responsive anionic co-polymer of poly (N-isopropyl acrylamide) (PNIPAM) as a selective flocculant/flotation collector. PNIPAM is used for separating hematite from 50:50 mixtures of hematite and quartz, at a variety of particle sizes. The performance of PNIPAM in this system is compared to that of conventional flotation collectors: sodium oleate and sodium dodecyl sulfate. The results of the study demonstrate that anionic PNIPAM used at 50¦C (above the lower critical solution temperature (LCST)) is the most effective flotation collector for hematite particles in the size range between 10 and 20 ¦m. This is attributed to the increased probability of both particle/bubble collision and particle/bubble attachment through the formation of hydrophobic hematite aggregates. Anionic PNIPAM used at 50¦C also produced the highest hematite recoveries for very fine hematite particles (circa 1 ¦m). However this recovery was completely unselective. This lack of selectivity is partially attributed to the activation of quartz particles by PNIPAM, but is thought to mainly occur as a result of entrapment of quartz particles within the matrix of hematite aggregates.CITATION:Forbes, E and Franks, G V, 2013. Selective separation of hematite from quartz by flotation using a temperature responsive polymer, in Proceedings Iron Ore 2013, pp 381-390 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 12, 2013

By A. René Silva

The separation of Fe(III) from simulated Ni(II) solutions using different ion exchange resins was studied. The resins tested included cation exchangers with sulfonic and carboxylic groups and chelating resins with iminodiacetic, aminophosphonic, and mixed sulfonic and phosphonic groups. The dosage of resins was varied from 0.1 to 0.5 g/mL to study the impact of resin type and dosage on iron separation from simulated nickel leach solution containing 25 g/L Ni(II) and 25 g/L Fe(III) at pH 1.5. Also, the effects of different metal ion concentrations, Fe (III):Ni(II) ratios in solution, pH, and adsorption times were investigated. Experimental results demonstrate that all the chelating resins selected favored the adsorption of Fe(III) over Ni(II) with high Fe(III) loading. Soft cation exchange resins also favored the adsorption of Fe(III) over Ni(II), but no significant Fe(III) loading was observed. In contrast, strong cation exchange resins did not show adsorption preferences. The most efficient separation was observed using resin with aminophosphonic groups at resin dosage of 0.2 g/mL, having a Fe(III) adsorption over 94% and Ni(II) adsorption below 5%.

By A. Güney

Currently, recycling technologies use relatively homogeneous plastics because hand-sorting waste feed is too expensive. Many promising technologies for separating mixed thermoplastics are being investigated, but they are still uneconomical and unreliable. Burning plastics for recycling is not used because of poisonous gases released when their burning. PET and PVC cannot be separated using conventional gravity separation techniques because their specific gravities overlap; PET density changes from 1.33 g/cc to 1.37 g/cc and PVC density is between 1.32 g/cc and 1.37 g/cc. For this reason, plastic recycling needs new techniques. Among these techniques froth flotation, also used in mineral processing, can be useful for its cost and simplicity. In this method, a plastic is selected from mixture, tried to regain its natural property, hydrophobicity. In this study the experiments were applied by using plasticizer reagents to make the selected plastics hydrophobic and us-ing NaOH to render the other hydrophilic. Post-consumed PET and PVC are evaluated by concerning the effects of selected parameters (particle size, concentration of plasticizer reagent, amount of NaOH, conditioning time and the effect of conditioning temperature). At the end of the experiments, optimum parameters for selective flotation of PET from PVC was found as particle size of -4.76 + 3.36 mm, NaOH amount of 30 kg/t, conditioning temperature of 75°C, conditioning time of 30 minutes, reagent amount of 300 mg/L. Consequently, PET was re-covered with 99.7% purity and 57% efficiency.

Jan 1, 2014

By Jannette L. Chorney, Katie J. Schumacher, Katelyn M. Lyons, Jerome P. Downey

The Metallurgical and Materials Engineering Department at Montana Tech is investigating a new method of extracting and refining rare earth elements (REEs) from mineral ores and concentrates. The relative stabilities of various REE compounds and differences in vapor pressures are exploited to selectively separate rare earth chlorides, with dysprosium and europium chlorides used as proof-of-concept experimental materials.

Mar 1, 2017

By R. L. Bruening, N. E. Izatt, S. R. Izatt

The need for selective metal separations has increased as the mining industry encounters more complex ore bodies and demand for higher performance end products expands. The Molecular Recognition Technology (MRT) process uses highly selective SuperLig® resins to remove desired metals from a variety of solutions in the mining and metals processing and recovery industries. MRT separation processes efficiently produce high purity metal products. In this paper, applications of MRT to metal recovery at mg/L to multiple g/L concentration levels are presented and discussed. Specific examples in the precious metal, nickel, cobalt, zinc, copper, and rare earth industries are given.

Jan 1, 2014

By R. L. Bruening, R. M. Izatt, N. E. Izatt, K. E. Krakowiak, S. R. Izatt

The need for selective metal separations has increased as the mining industry encounters more complex ore bodies and the demand for higher performance end products expands. Molecular Recognition Technology (MRT) is a green chemistry process that involves use of SuperLig® resins to selectively remove desired metals from a variety of solutions in mining and metals processing industries. Recoverable metal concentrations can range from multiple g/L to mg/L or less. The MRT separation process is based on green chemistry principles and can efficiently produce high purity metal products with minimal waste generation and energy usage. In this paper, applications of MRT to metal recovery and purification in the minor and specialty metals industry will be presented and discussed. Examples will be described involving cobalt, nickel, zinc, rhenium, iridium, indium, germanium, bismuth, and cadmium, as well as removal of lead and iron from process streams.

Jan 1, 2015

By R. L. Bruening, J. B. Dale, N. E. Izatt, S. R. Izatt

IBC Advanced Technologies&apos; Molecular Recognition Technology (MRT) SuperLig® products selectively and rapidly bind with target metal ions to remove them from solution. The MRT process can produce a high purity separation product of maximum added value at low cost. This paper discusses applications for MRT in the gold industry, including recovery of gold and silver as well as metal contaminants from various process and recycle streams.

Jan 1, 2011

By E. S. Peterson

The selective separations of trace metals- and organics from water are processes of importance to industry. The application of a new metals capture technology coupled with polymer membrane technology has proven to be one avenue to accomplish such selective separations. The polymers used in these studies are polyphosphazenes. Polyphosphazene polymers consist of an alternating backbone of nitrogen and phosphorus atoms. The polymers have high thermal and chemical stabilities. Experiments at the Idaho National Engineering Laboratory demonstrate that polyphosphazene membranes coupled with Chromato Chem,"Chelation Chromatography" process are capable of removing both chlorinated hydrocarbons and metal ions from process streams. These results point to a wide range of potential industrial and environmental applications for such systems. Data will be presented which show the efficiency and selectivity of separations, postulated separation mechanisms, and the initial designs of industrial demonstration units which are currently under construction. Parts of this work have been performed under a Cooperative Research and Development Agreement (CRADA) between ChromatoChem, Inc. and Idaho National Engineering Laboratory (INEL). The work at INEL was been sponsored by the United States Department of Energy&apos;s Office of Industrial Technologies

Jan 1, 1995

By Ximena Diaz

Mercury is one of the most undesirable contaminants in gold bearing ores. During cyanidation mercury cyanide compounds accompany gold in all the extraction and recovery processes. Of course mercury in the carbon eluates creates environmental problems in subsequent refining steps. One possible process alternative for the separation of gold from mercury in such concentrated alkaline cyanide solutions is the selective solvent extraction of gold by undiluted Dibutyl Butyl Phosphonate (DBBP). In order to describe the behavior of mercury during extraction by DBBP, the results from a preliminary research program are presented. In this study, temperature and cyanide concentration have been found to be the most significant variables which influence the separation of gold from mercury by solvent extraction using DBBP. It was found, using plant eluate from a carbon strip, that excellent separation of gold from mercury can be obtained at 60&apos; C with 98% gold recovery and complete mercury rejection in a single stage of extraction. The influence of pH is also discussed in terms of the extraction chemistry. These results complement previous research which described the DBBP solvation extraction of an aurocyanide ion pair. In addition, these results extend our understanding of the alkyl phosphorous ester extraction systems by illustrating that neutral ionic species such as Hg(cN)02sq, can be extracted at low cyanide concentrations, a phenomenon which had not been observed previously for other cyanoanions.

Jan 1, 1993