Search Documents

By Favreau R. F. Ph. D, Favreau Patrice

The article explains that the way to achieve a successful blast is by insuring that the explosive energy divides properly into the weakening action of the shock wave which is necessary to prevent large collar blocks and toe, and into adequate stress field intensity SS which is necessary to obtain good fragmentation size distribution at the crusher, as well as adequate burst out rock movement to achieve easy mucking.

Feb 1, 2020

By George M. Fowler, J. P. LYDEN

T HE relationship of geological structure to orebodies and to the great masses of chert in the Tri-State mining district is of such significance that it prompts a brief recital of the existing information regarding the various periods of structural deformation. We began to note a relationship between structure and orebodies early in our studies of the field, and further work revealed a like relationship of structure to the great masses of chert so commonly associated with the ore-

Jan 1, 1934

By Guillermo V. Borquez

INTRODUCTION The basic factors that influence the selection of a mining method are the geometry of the ore deposit and the strength of the ore and surrounding rock. These factors usually determine the ore recovery and dilution of the deposit under analysis. For the purpose of this paper we will consider a generalized case of a block caving system and the sequence of the analysis needed to optimize ore recovery. The analysis presented is intended for the preliminary planning stage. The critical factors involved in the caving process are identified and the methods for evaluating the suitability of a particular deposit to the caving method of mining are outlined. The mine design is approached by identifying the two most important, dimensions: the size and spacing of the draw points. These dimensions are estimated from a simulation model which takes into account the ore recovery, the incremental value of the ore recovered, and the safety conditions of the operations. The model estimates the number of draw points required to extract efficiently and safely the broken ore from the caving area. This number is found in the range where the net incremental value of the ore is maximized and the probability of pillar failure does not exceed the limit which is acceptable for a safe mining operation. A mining method and its design are in a continuous process of optimization. This process is unique for each deposit because of the many parameters involved; therefore, a back analysis of the operations should be performed when possible. These analyses will indicate if the ore body responds in a predictable manner to the parameters contained in the geological, fragmentation, and draw point models. SELECTION OF ALTERNATIVE MINING METHODS The selection of a mining method best suited to define the minable ore reserves of a given deposit involves consideration of the geometry of the ore deposit and the strength of the ore and surrounding rock. These two factors are usually sufficient to determine the ore recovery and dilution of the deposit. After analyzing the geological reserves and defining the limits of the deposit, either an open pit or an underground mining method can be selected to define the minable ore reserves. The sequence of steps to follow in the selection of a mining method is presented in Figure I. From an economic point of view, the strip- ping ratio is the determining factor for the selection between an underground or open pit method. In turn, the stripping ratio is a function of the grade distribution and con- figuration of the ore body. In order to obtain a preliminary estimation of the stripping ratio, a parametric analysis could be applied, such as the approach used by Professor E. P. Pfleider (1972) and summarized in Table 1.

Jan 1, 1981

By Lazar Kricak, Zoran Teodorovis, Dragan Bogunovic

Scattering of delay interval around nominal value is an important issue in blasting practice. The scatter interval, as becomes wider, increases a probability of time delay overlapping adjacent blastholes. An excessive flyrock, ground vibrations, air blast and poor fragmentation are the symptoms for scattering related problems. Utilization of the short delays in the blastholes and longer delays on the surface are recommended solution to overcome mentioned problems. In contrast to global trends manifested through the application of electronic detonators and non-electric shock tube systems, revitalization of inexpensive electric detonators in combination with an accurate initiation system may be an acceptable solution. An extensive work was carried out at the Blasting Center Laboratory at the College of Mining and Geology, University of Belgrade, to develop a precise initiation system. As a result, Sequential Blasting Initiation System – Radio Frequency (SBIS-RF) was developed. It is expected that this system will increase blasting productivity, and reduce negative environmental impacts and total blasting costs.

Jan 1, 2008

By Stephen Njoloma, William Bracken, Harald Cordes, Ivan Hee

"DC Water’s First Street Tunnel (FST) is part of the $2.6 billion Clean Rivers Project designed to reduce the occurrence of combined sewer overflows into local waterways. Due to flood events in the Bloomingdale and LeDroit Park neighborhoods, the FST Project was accelerated by DC Water to mitigate future flooding by boosting storage capacity and thus relieving the undersized combined sewers.The FST Project was finalized in 2016 as a collaborative effort between DC Water, its consulting team consisting of Greeley & Hansen and McMillen Jacobs Associates, and the design-build team of Skanska, Jay Dee Contractors (SKJD) with WSP Parsons Brinckerhoff as the designer.Scope of project. The FST Project (Fig. 1) included four primary shaft sites, a large 6 m (20 ft) internal diameter, 823- m (2,700-ft) long bored tunnel and three adit connections from the off-line shafts to the large-diameter tunnel. The adits which vary in size and length, are the subject of this article. The Channing Street site (Fig. 2) was established as the main site for an Earth pressure balance tunnel boring machine (TBM) and included a 49-m (160-ft) deep shaft with slurry wall support of excavation and 20-m (65-ft) internal diameter final cast-in-place permanent concrete liner. The construction sites at Adams Street, V Street and Thomas Street each consisted of off-line shaft structures tied to near-surface sewer diversion chambers and ventilation facilities. These three off-line shafts were connected to the large bored TBM tunnel via adit tunnels. Each of the three adits had a portion or the entire length excavated by sequential excavation method (SEM) in frozen ground.The Adams Street adit (Fig. 3) was constructed in two phases. The first phase is the 23-m (75-ft) long and 5-m (16-ft) diameter section immediately outside the drop shaft which also serves as the deaeration chamber and was excavated by SEM. The second phase which is 91 m (300 ft) long and 3 m (10 ft) in diameter was excavated by Micro TBM (MTBM) launched from within the permanently lined deaeration chamber. MTBM excavation commenced toward a reception chamber that was excavated by SEM from the previously bored FST TBM tunnel. This SEM excavation had a 5 m (17 ft) diameter and a length of 4.5 m (15 ft)"

Jan 3, 2018

By K. D. Peaslee, V. L. Richards, C. H. Rawlins, S. N. Lekakh

"Steel-making processes generate carbon dioxide air emissions and a slag co-product. The aim of this project was to develop a functional sequestration system using steelmaking slag to permanently capture carbon dioxide emitted in steelmaking offgas. A possible parallel benefit of this process would be rapid chemical stabilization of the slag minerals with reducing swelling or leaching.This paper summarizes the original results of the project, including mineralogical and structural features of carbon sequestration with steel making slag, mathematical modeling of reaction phenomena using a modified shrinking core model, METSIM modeling of several possible industrial applications, a thermo-gravimetrical study of the reaction between slags and different gases, and design and testing for a lab scale apparatus consisted of two reactors.1. IntroductionThe U.S. produces 9-14 Mt of steelmaking slag annually, which represents approximately 10-15 wt. % of crude steel output.1,2 Primary uses for steelmaking slag include high quality mineral aggregate, Portland cement, unconfined fill, soil conditioning, and pH neutralization of abandoned mine drainage.3,4 The key factor prescribing slag use is the alkaline-earth metal (e.g. Ca and Mg) oxides content, which contribute to overall basicity and cementitious strength. However, as-produced steelmaking slag is chemically unstable. Calcium and magnesium oxides readily form hydroxides and carbonates through reaction with atmospheric gases. Both hydroxide and carbonate formation produce substantial mechanical swelling leading to heave failure in confined construction applications, thus many states dictate stockpile aging for 3-6 months prior to commercial use.5,6 Sequestration of carbon dioxide is a natural corollary to forced carbonation. The conversion of CaO/MgO to carbonates serves both to stabilize the slag, and permanently capture and store the CO2."

Jan 1, 2008

By M. Z. He

Attractive particle interactions which underpin the sliming of gangue mineral particles onto valuable mineral phases are encountered in a number of flotation circuits. Sliming leads to poor flotation recovery of the valuable minerals and high recovery of the gangue particles in the concentrate. To mitigate sliming, low molecular weight poly-electrolytes are commonly used as dispersants during pulp conditioning prior to flotation separation of the valuable and gangue mineral phases. In the present work, the sliming mechanism of sericite onto chalcocite and the influence of interfacial chemistry and two anionic copolymer dispersants (carboxylate substituted polyacrylamide, polymer Cyquest 3223 and sulfonate substituted polymaleic acid, polymer P80) on the sliming interactions were probed in the pH range 5~9. It was shown that the sliming occurred under solution conditions where both chalcocite and sericite particles were negatively charged, as evidenced by their apparent particle zeta potentials. The suspension pH had a profound effect on sliming process as the extent was markedly greater at lower than higher pH. The sliming was found to be due to the chalcocite dissolution, Cu (I) release and oxidation to Cu (II), followed by hydrolysis and specific adsorption, leading to sericite particle surface charge reversal and the formation of electropositive sites on chalcocite surface in the pH range 5~9. Addition of polymer Cyquest 3223 or P80 not only increased the magnitude of zeta potentials of both sericite and chalcocite particles but also reduced the formation of Cu (II) ions and complexes, which mitigated the sliming behaviour. The adsorption of polymer Cyquest 3223 or P80 at 3 g polymer / kg solid or more had a significant impact on the zeta potentials of both sericite and chalcocite particles. Sericite-chalcocite particulate adsorption studies showed that sliming was completely suppressed via an electro-steric repulsion mechanism resulting from anionic polymeric dispersant adsorption at dosages > 3 g polymer / kg solid.

Jan 1, 2014

By Richard Jr. Ray, David Johnston, Phil Blankenship

Injection of inert gases to combat mine fires has been practiced in various parts of the world for a long time. Of late, nitrogen has become the preferred inert gas for control of mine fires and safe salvage of longwall equipment as compared to carbon dioxide or fuel gases produced from burning of fuel. In India, carbon dioxide has been used for fire fighting in a number of mines during the 1960s and 1970s. More recently inert gas produced from burning of fuel oil in surface plants has been used in controlling the atmosphere in fire areas in two mines. In yet other cases, liquid nitrogen has either been poured directly into fire areas in liquid form or injected in gaseous form to keep the fire in check. Nitrogen produced in liquid form in an oxygen plant is more costly than nitrogen produced from PSA (pressure swing adsorption) based plants. A PSA-based plant has been installed in one of the Indian mines in 1986 and more are in the offing. This paper reviews the application of various inert gases in Indian mines and discusses the likely trend of inert gas application in Indian mines in the future.

Jan 1, 1989

On my arrival in New York after the Russian examinations John D. Ryan, president of Anaconda, asked me what my plans were. I told him I wanted to be useful somehow in the World War that we had entered while I was away, but I did not know how. Ryan and Thayer told me that the new American Air Corps was gathering a group of executives, most of them young, to go to France as Army officers to help with the industrial side of our aviation activities. This would include construction of military airports, maintenance, and supply for our rapidly growing Air Corps. They thought I might be accepted in this group of about 30. It seemed to be just what I wanted, and I put in my application at once. My application was accepted about three weeks later and I was told to come to Washington to take physical and other tests and to meet others of the group. I liked them. They were a cross section of competent American manufacturers, bankers, automobile executives, and merchants. I was the only miner. I had many discussions in the days in Washington with members of our organization and others I knew who were going into war service. Attitudes were very different from those 55 years later. There was no discussion as to whether war was right or wrong. We were in it and must do all we could to help. At the same time there was a holdover from the days when, at least for the elite, war was high adventure. Even the most high-minded did not then realize that war is a horrible form of wholesale murder and, in 1917, it would have been treason to suggest this. I had two weeks before our industrial group was to start work which gave me time for a hurried trip to Berkeley where Dorothy and I announced our engagement.

Jan 1, 1976

"The Ohio River Bridge East End Crossing Tunnel requires a 75-year service life of its cast-in-place reinforced concrete lining. This twin-tube 3-lane (each tube) highway tunnel is about 55-ft wide and 30-ft high. Since unified tunnel service life prediction methodology does not exist in the US, challenges occurred during the design-build phase of this project. These challenges include the methodologies in determining the reinforced concrete’s degradation mode, the lining’s surface chloride concentration level, the reinforcing steel’s critical chloride threshold value for corrosion, how to verify the concrete’s diffusion coefficient, and the durability impact from concrete crack width. This paper presents a methodology in verifying the proposed concrete mix can achieve the service life requirements. This methodology can be adopted for service life prediction for future tunnels to be built in the US. INTRODUCTION The Ohio River Bridge East End Crossing (ORBEE) Tunnel is part of a Public Private Partnership project, which connects transportation network between Louisville, Kentucky and southern Indiana. Located in Louisville, Kentucky, the twin-tube highway tunnel provides northbound and southbound lanes of the Kentucky approach to a new bridge across the Ohio River. Tunnel lengths are approximately 1,675-ft and 1,685 for the northbound tube and the southbound tube, respectively. Connected by two cross-passages, both tubes have a roadway width of 40-ft, for 3-lane traffic, and a vertical clearance of 26.5-ft.The tunnel was constructed by drill and blast method with shotcrete and rock dowels as initial ground supports. The final tunnel lining system includes: •,Nominal 16” cast-in-place reinforced concrete lining, with 2” and 3” concrete covers over reinforcing steel for its extrados and intrados, respectively. •,20” cast-in-place reinforced concrete invert slab, with 4” and 3” concrete covers over reinforcing steel on its top face and bottom face, respectively. •,PVC waterproofing system around tunnel perimeter, excluding invert slab. •,Perforated PVC groundwater collection pipes on both sides of the tubes and one below the invert slab of each tube."

Jan 1, 2016

By AIME AIME

A DOCUMENT of progress and of great interest to engineers is the report of the Military Affairs Committee of 'the Engineering Council, which has just been accepted and sent to the secretary of War. It provides .a plan whereby civilian engineers holding commissions in the Reserve Corps may; with their con- sent, be called into service of the army during peace at any time, either with troops in the field or in a consulting capacity on any government engineering work. The Military Affairs Committee finds ample authority in the military bill passed by Congress on June 4, 1920, for this arrangement and also for extending the privilege to military engineer, officer-s of the regular army to engage in civilian work during times of peace. It is hoped that the Secretary of War will adopt the suggestions and put the program outlined into effect. This is a constructive piece of work comparable to the efforts of the military Committee before the war which developed so much in the way of preparedness, particularly in the program of military lectures which, held in the auditorium in the Engineering Societies Building, became so popular that each lecture had

Jan 1, 1920

By M. Rossi

The use of service variables in geostatistics (grade-thickness) is common in industry when developing block grade models and geologic resource estimates. This is particularly true in the case of sedimentary and stratabound-type deposits. The approach has proven merits when assessing ore reserves. However, there are cases where its application for preliminary data analysis produces biased estimates. One such case is encountered in uranium disequilibrium studies. This paper demonstrates the inadequacy of service variables when performing uranium disequilibrium studies. Disequilibrium analysis is a necessary preprocessing step when radiation counts are used as raw data to calculate uranium reserves. Typically, a probe is used to obtain the gamma counts from open drill holes. These counts are then regressed (and corrected) against chemical assays obtained from core samples. During this process the grade-thickness variable produces an optimistic image of the relationship between probe grades and chemical (true) grades, causing overestimation of the final geologic resource. The problem is analyzed through a case study.

Jan 1, 1993

By M. Rossi

The use of service variables in geostatistics (grade-thickness) is common in industry when developing block grade models and geologic resource estimates. This is particularly true in the case of sedimentary and strata-bound-type deposits. The approach has proven merits when assessing ore reserves. However, there are cases where its application for preliminary data analysis produces biased estimates. One such case is encountered in uranium disequilibrium studies. This paper demonstrates the inadequacy of service variables when performing uranium disequilibrium studies. Disequilibrium analysis is a necessary pre-processing step when radiation counts are used as raw data to calculate uranium reserves. Typically, a probe is used to obtain the gamma counts from open drill holes. These counts are then regressed (and corrected) against chemical assays obtained from core samples. During this process, the grade-thickness variable produces an optimistic image of the relationship between probe grades and chemical (true) grades, causing overestimation of the final geologic resource. The problem is analyzed through a case study.

Jan 1, 1991

By Peter Cali

There is one organization in Sweden, The Swedish Deep Stabilization Research Centre, which has been working with these questions and there is also a project, Eurosoilstab, within European Union to take a manual for deep stabilization.

Feb 10, 2003

By George Burke

Of the three projects, particularly the extensive Nimitz II (downtown) project, a single system, which was part of the operation, was used to control the spoil. Spoil control was continuous with the work since a vacuum truck and crew was used to suck up the spoils as they came out of the borehole. So, the whole job was kept clean both during operations and at the end of the shifts. On the Sand Island project, a double system was used. Larger spoil quantities were contained within the shaft limits during the work and the cleanup or disposal of the spoils was performed during excavation.

Feb 10, 2003

By Helen Ahnberg

The scope of the present paper is limited to report the experimental evidence and not for describing the analytical assumptions. However, the idea behind the experimental program is that the deterioration may be caused by the leaching of Ca from the treated soil to surrounding soil or water driven by the difference in the Ca ion concentration. As a consequence of Ca leaching, it may be natural to expect the expansion of micro void space within the treated soil. In a saturated condition, the water inflow into the treated soil may accompany the leaching phenomenon. We measured the water content within the treated soil. But there is not much difference in water content within the soil.

Feb 10, 2003

By Peter Iovino

Unfortunately, I don't know the unit cost per cubic yard of treatment. I reflected on that yesterday and I don't think that we considered the use of micropiles. They could have been an option. The challenge may have been picking up some of the lateral load but I think the micropiles could have been installed on a batter and perhaps extended to rock. We could have considered them, but I do not believe we explored micropiles as an option for this project.

Feb 10, 2003

By Stefan Dahlin

The laboratory tests indicated low permeability but as I said, as a rule, the permeability in the field has been found to be higher. A high permeability has also been found when doing back calculations of rates of settlements in different cases. But as I also said, there's a need for further studies in this area.

Feb 10, 2003

By Mitsuhiro Shibazki

I can't answer that question but I am looking at Andy, my co-author, and he says we didn't measure it. No movement. If I understand it correctly, how do we handle lateral forces in shear? The main columns were designed as pin connections so there wasn't a moment in the shear between the pile cap and the columns the steel reinforcing was used to resist that. I am not aware of how we would have installed those, it is possible to try and submerge them all if the jet grout is still fluid. They were higher than design. You are correct.

Feb 10, 2003

By Mary Ellen Bruce

Let me first address the issue of the wet grab samples. The wet grab samples that were attempted to take on the Central Artery were hindered by the fact that the way the mixing was being done was only by injecting grout on the way out, during withdrawal of the mixing tools. They would auger down to the required depth (usually with some water being injected), which took anywhere from 45 minutes to an hour, and then when coming out, the grout would be injected with grout. That was leaving a column of grout in the center where the shaft had been (i.e. inside of the blades of the mixing tools), which would end up being something like a foot in diameter because the pipe that was used for the drill shaft was a foot in diameter. So we had 10 inches to a foot of almost pure grout in the middle of our column and then we had 2 feet on either side that was mixed soil cement. So when they went down with the wet grab sampler not knowing where that was in the column sometimes they/we were getting strengths of 1500 psi, and sometimes they/we were getting strength of 500 psi or 100 psi. So what was it that we were taking into the wet grab sampler? In those cases you don't really know, but it wasn't representative of the core samples we were taking. We were purposely not coring in the center because we knew that was going to be high cement content, almost pure grout. So the issue of wet grab sampling particularly on this project, the Central Artery Project, was that we didn't really know what we were sampling. What becomes an issue with wet grab sampling in other projects is that you have to have another device (machine) in most cases, a cherry picker crane or something similar that can raise and lower with a beam that is used to forces the sampler down into the freshly mixed soil-cement. And regarding economics, is it more economical to have that crane standing by with its operator or to have a drill rig to come along later and do the coring and take the material out that's fairly identical to what you're finding in situ? The complaint of micro-fracturing in the core samples as you're taking the cores was raised by Seiko as causing large strength reductions. But, if you're doing it carefully, then I don't think that's much of an issue anymore, on research basis perhaps but not on a practical level.

Feb 10, 2003