Search Documents

By Hubert Bril, Priscilla Pareuil, François Bordas, Emmanuel Joussein, Jean-Claude Bollinger

"According to the legislation, valorization type, origin and characteristics of waste material, various standard procedures are available to evaluate environmental impacts. A Mn-rich slag was sampled from a metallurgical plant. After its characterization (elementary analysis and mineralogy), five standard procedures were carried out (i.e. TCLP, EN 12457-1). Each fixed parameter of the standards was systematically studied in a large range: pH, Liquid/Solid ratio, contact time. For example, EN 12457-1 led to a low ME mobilization, increasing with the L/S ratio, the contact time and an acidic pH. As a conclusion, the representativeness of the considered parameters and their potential variations are predominant to assess of the real environmental impact during slag reuse. Introduction Recent studies have been carried out about environmental impacts of waste containing metallic elements (ME) because of their potential mobility [1-7]. Indeed, slags are either dumped or valorized in various activities such as building materials. In order to assess environmental risk, various standard procedures are used depending on country legislation, origin of waste and valorization way. Results of leaching tests are linked either to special legislation (e.g. Dumping: EC, Council Decision 2003/33/EC, Construction products: EC, Council Directive 89/106/EEC) or to legal levels used in drinking water (Directive 98/83/CE) when leachates could migrate to groundwater. If ME in leachates are lower than drinking water authorized levels, the waste will be considered as non-hazardous. On the contrary, if the leachable amounts exceed them, the question about the risk has to be posed. Beyond the abundance of leaching tests available, variety of operational conditions induced by these regulatory tests does not make the choice easier. According to operational conditions induced, ME release could vary from one test to another one. ME concentrations in leachates depend on pH, Liquid/Solid ratio, contact time and particle size [3]. To highlight the importance of these operational parameters, potential risk for valorization of a manganese-rich slag was assessed by comparing several standard leaching protocols [8-12] with a global study dealing with the influence of operational conditions. For each regulatory protocol, the most influential parameters (L/S ratio, pH, particle size and contact time) have been studied in a large range."

Jan 1, 2008

By Q Zhuo, P C. Pistorius, M N. Al-Harbi

A likely increasingly important pathway for future low-carbon ironmaking and steelmaking is the combination of gas-based direct reduction with electric furnace steelmaking (DRI-EAF route), or with electric smelting (DRI-ESF route). In the DRI-EAF route, the gangue that is present in the iron ore is fluxed and removed as slag in the melting (steelmaking) step. This is in contrast with integrated steelmaking, in which the gangue is removed as part of blast furnace ironmaking. For DRI-EAF steelmaking, the amount and composition of slag depend on the iron ore composition, flux additions and iron yield. Slag volume and composition affect phosphorus removal, foaming behaviour and the process energy requirements. In this work, heat data from a year of DRI-EAF production was analysed to test whether the expected relationship between slag volume and electricity consumption for EAF steelmaking was observed. The data include slag analyses (one sample per shift), and heatlevel information on all inputs, final steel temperature and dissolved oxygen concentration, electricity consumption, tapped steel mass and tap-to-tap time. In analysing the data, the slag volume was estimated from the assayed slag CaO concentration and CaO inputs to the EAF. The expected effect of slag volume on steelmaking energy consumption was calculated with a mass and energy balance, considering the heat of mixing of the slag. The calculated energy requirement of slag formation is in line with previous estimates reported in the literature.

Aug 21, 2024

By J H. Park, R R. Kim, H S. Park, H J. Kim

This study focuses on the recovery of valuable metals, specifically silver (Ag) and palladium (Pd), from copper-containing sludge (with copper content less than 20 per cent) generated during PCB processing and from spent petrochemical catalysts used in vapour decomposition during oil refining processes. The present results indicate that an increase in the mixing ratio of alumina-based spent catalyst leads to a decrease in the recovery rate of Ag and Pd. The recovery rates for Ag and Pd range from 84 per cent to 96 per cent and 80 per cent to 98 per cent, respectively. This trend is attributed to the increased emulsification of copper droplets containing Ag and Pd in the slag. The emulsification is caused by the decrease in the settling velocity of the copper droplets due to the increased viscosity of the slag as well as by the decrease in the slag-metal interfacial tension due to an increase in sulfur content at higher mixing ratio of spent catalyst.

Jun 19, 2024

By B A. Webler, P Su, P C. Pistorius

Advanced high-strength steels (AHSS) typically have much higher aluminium concentrations (by an order of magnitude or more) than conventional low-carbon aluminium-killed steels. The resulting lower oxygen activity at the steel-slag interface changes the kinetics and thermodynamics of steelslag reactions. Previous work showed that the rapid transformation of alumina inclusions to spinel inclusions, and spinel to periclase, occurs because of the relatively high concentration of dissolved magnesium. In this paper, experimental results on nitrogen removal by ladle slag are compared with predictions based on the available thermodynamic databases. As in previous work, the kinetics was modelled by assuming mass transfer control, with steel or slag mass transfer limiting. The results show that significant removal of nitrogen by steel-slag reaction is possible.

Aug 21, 2024

By Florian Kongoli

Slags and fluxes are important interchangeable dimensions of pyrometallurgical processes. They can increase the efficiency of the smelting, converting and refining processes and improve the quality of the final products. A good slag should have appropriate physicochemical properties such as low liquidus temperature, optimal viscosity, maximum ability to attract undesirable elements, minimum potential of attracting valuable elements, etc .. A good flux, on the other hand, when properly used, can considerably improve the physicochemical properties of the slag since by modifying its chemical composition it could decrease the liquidus temperature, improve viscosity etc.. Consequently, the choice of a good slag and the corresponding fluxing strategies has become indispensable in most of industrial processes. However, the properties of multicomponent slags as well as the effect of several fluxes are known only empirically and confusion exists in the literature and in the industrial practice. In today's reality of frequent changes in the composition of raw materials and that of the fluxes themselves, in the existing or new developing technologies, the quantification of the thermophysicochemical properties of multicomponent slags and the effect of fluxes becomes indispensable. This paper reviews some of the work carried out by the author's group during the last ten years on the quantification of the thermophysicochemical properties of multicomponent slags and on the effect of fluxes in several smelting and converting processes in close relation to their individual characteristics. Several examples have been given in order to demonstrate the fact that when taken outside the context some fluxes can become in fact anti-fluxes.

Jan 1, 2003

By Florian Kongoli

Slags and fluxes are important interchangeable dimensions of pyrometallurgical processes. They can increase the efficiency of the smelting, converting and refining processes and improve the quality of the final products. A good slag should have appropriate physicochemical properties such as low liquidus temperature, optimal viscosity, maximum ability to attract undesirable elements, minimum potential of attracting valuable elements, etc .. A good flux, on the other hand, when properly used, can considerably improve the physicochemical properties of the slag since by modifYing its chemical composition it could decrease the liquidus temperature, improve viscosity etc.. Consequently, the choice of a good slag and the corresponding fluxing strategies has become indispensable in most of industrial processes. However, the properties of multi component slags as well as the effect of several fluxes are known only empirically and confusion exists in the literature and in the industrial practice. In today's reality of frequent changes in the composition of raw materials and that of the fluxes themselves, in the existing or new developing technologies, the quantification of the thermophysicochemical properties of multicomponent slags and the effect of fluxes becomes indispensable. This paper reviews some of the work carried out by the author's group during the last ten years on the quantification of the thermophysicochemical properties of multicomponent slags and on the effect of fluxes in several smelting and converting processes in close relation to their individual characteristics. Several examples have been given in order to demonstrate the fact that when taken outside the context some fluxes can become in fact anti-fluxes.

Jan 1, 2003

By M. R. Fletcher

Slags generated by the ferrous metals industry can he used to produce high-value ceramic materials. The properties of these ceramics can be controlled by judicious choices of composition, additives, and processing parameters. Standard methods of materials handling, such as comminution and mixing, are as applicable to slag as to any other mineralogic raw material. In this study, foundry slag was ground, homogenized, melted, and, formed to produce a glass, and then heat treated to crystallize it into a high-strength glass-ceramic. The product shows promise as a low-cost, wear-resistant tile material that (-an he custom cast. This and similar materials made from slags and natural rocks are candidates for use as construction materials, acid-resistant piping, shock-resistant sheathing, rot-proof pilings, and, when foamed, even as pontoons.

Jan 1, 1990

By M. R. Fletcher

Slags generated by the ferrous-metals industry can be used to produce high-tech ceramic materials. The properties of these ceramics can be controlled by judicious choices of composition, additives, and processing parameters. Standard methods of materials handling, such as comminution and mixing, are as applicable to slag as to any other mineralogic raw material. In this study, foundry slag was ground, homogenized, melted and formed to produce a glass, and then heat treated to crystallize it into a high-strength glass-ceramic. The product shows promise as a low-cost wear-resistant tile material which can be custom cast. This and similar materials, made from slags and natural rocks, are candidates for use as construction materials, acid-resistant piping, shock-resistant sheathing, rot-proof pilings, and, when foamed, even as pontoons.

Jan 1, 1988

By Lauren M. Roberts, Ralph R. Sacrison

Pipeline or borehole free-fall transfer of material has long been done in support of underground mining. This paper addresses some characteristics and design elements in selecting systems suitable to the transferred media and the mine requirements. Though aspects of overall systems are discussed, principal attention is directed to the slickline/dropline/transfer line and the discharge diverter/rockbox/energy dissipator/boot. These terms are common to these systems, often used interchangeably, and will be used as appropriate to the material, equipment and construction. Following several design sections, fabrication and construction, and system operating and maintenance procedures are discussed.

Feb 1, 2025

By Klaus Gamweger

"This paper introduces an innovative solution to open and close the tap hole of different furnace types in the copper industry with a slide gate system. Two plates with defined drilled holes are slid against each other, which enables effective starting and stopping of the copper flow as well as throttling. Typically, the copper is poured via a tap hole into a launder system by rotating the furnace into an appropriate position. Control of the casting rate is also performed in this manner. Or, in case of stationary furnaces the tap hole is opened by oxygen lancing and closed manually with a clay- or copper-cone. These procedures show a lot of disadvantages including splashing, oxygen pick-up, and energy losses as well as a severe danger for the working staff. All these problems can be overcome with an appropriate slide gate system.IntroductionThe control of the casting rate of a copper anode furnace usually is performed by rotating the furnace into an appropriate position. This implies that the taping starts with the tap hole at a very high position. Copper splashing and an uncontrolled oxygen pick up are - with several more disadvantages - the consequences. RHI AG has developed an innovative solution for copper applications to open and close the tap hole with a slide gate system which allows also an accurate control of the flow rate. By using this system it is possible to start the casting procedure with the tap hole at the deepest position, directly above the launder. This paper presents this new slide gate system in detail and shows the advantages in production and safety issues."

Jan 1, 2012

By J. Tuzson, H. McL. Clark

Introduction Wear of pumps, wet cyclones and pipelines by suspended solid particles will impact their operating economies by limiting their useful life, reducing their reliability and increasing the amount of servicing. Erosion is considered a materials problem. The empirical solution consists of testing different materials in field applications. Such tests are time consuming and expensive. The prediction of localized wear rates, life estimates and appropriate material selection demand a better understanding of the slurry wear process in environments corresponding to those found in working equipment. Key words: Wear, Slurry abrasion, Coriolis erosion tester The slurry wear process Solid particles suspended in liquid generally move with the flow, but such particles deviate under the centrifugal and Coriolis forces encountered in pumps. The concentration of particles will increase, and a solid layer or bed may accumulate if the acceleration is directed against the flow passage wall. Large particles in dilute suspensions may impact the wall. dissipating their kinetic energies and removing material. However, particles smaller than about 11)(1 µm encounter great drag when moving through the liquid. and such par¬ticles have little kinetic energy left when they reach the wall. They cannot penetrate the stagnant boundary layers present in pumps. Therefore, small particles tend to form beds that slide along the wall, removing material by a process that could he called sliding erosion or wet abrasion. Wear by impact erosion from large particles in dilute slurries can he predicted by appropriate analytical and empirical methods. However, laboratory tests and calculations of wear rates that correspond to sliding erosion are more likely to correlate with field experience from wear under similar conditions. Specific energy Data from laboratory slurry erosion experiments have shown that the amount of material removed is approximately in proportion to the energy expended in the erosion process. Thus. the specific energy-energy expended in removing by erosion a unit volume of material-offers a simple, practical measure for the erosion resistance of materials. The concept was found to also apply to sliding erosion (Clark et al.. 1997). Generally, the study of the material-removal process in slurry erosion continues to remain a subject of research. Conceptually, if the flow velocities and accelerations could be calculated in a pump or pipeline, the energy dissipated at the passage walls could also be estimated, and the material removal rate would become known from the specific energy determined by laboratory tests. Slurry erosion testing Laboratory devices made specifically for slurry erosion testing may be grouped into the following: jet erosion devices, slurry pots and the Coriolis test machine (Pagalthivarthi and Helmly, 1992). Jet erosion devices use a slurry pump and nozzle to produce a high-velocity slurry jet that is directed at a flat material specimen, either perpendicularly or at some acute angle. Combined impact and sliding erosion are produced. but the processes cannot be separated, and the wear is difficult to assess except by weighing. Slurry pots consist of a cylindrical vessel containing the slurry of interest. In the slurry pot, test specimens are attached to a rotating arm. The samples are rotated in the slurry and experience local flow conditions that result in combined impact and sliding erosion. Wear depth measurements from detailed laboratory experiments have been successfully correlated with results from an analytical model of the process, and specific energy values have been calculated (Wong and Clark, 1995). In industrial use, the samples are weighed to determine the total material loss. Materials are ranked with respect to some reference material. The Coriolis erosion tester (Tuzson, 1984) consists of a rotor with a central cavity, from which two opposing radial passages lead out (Fig. 1). The slurry is fed to the centerof the rotor in one pass from a stirred overhead tank. The slurry particles are subjected to the Coriolis acceleration as they flow out through the radial passages. The material specimens are mounted into the radial passage walls facing the direction of rotation and are eroded by the particles that are pressed against them as they flow out radially. A narrow groove is worn into the sample within a few minutes, using a few gallons of slurry. Material removal is estimated accurately from profilometer traverses across the wear scar at different locations. The energy dissipated by the particles can be estimated, which leads to a well-defined experimental value for the specific energy.

Jan 1, 2000

By Roswell Johnson

THE principle of sliding or graduation in royalties is accomplished either by the block, period, cumulative, or class method. The block method calls for a very low royalty rate on all oil produced up to. a certain amount. This amount would normally be that which is believed to suffice to repay the cost of the well. A higher rate would be charged after the well is making a profit. This method, common in many industries, is peculiarly inadaptable to any industry such as this where the productivity per day of the units gradually and inevitably decreases. This, for reasons given later, is because it forces an early abandonment of the well and so offends against conservation. In the period method, the royalty rate is changed by some definite amount when the well produces less than a specified quantity per day or other given unit of time. While simple to explain, it operates badly because a great deal is made to depend upon a small reduction in production, whereas the reduction as a matter of fact declines rather erratically owing to the exigency of lease management, connecting of tankage, and vagaries of the gaugers. These disadvantages are obviated by the cumulative method. In this method, all the production less than a certain amount per week has one rate of royalty, or none at all, and the oil produced in excess of that amount pays an additional rate of royalty. In the long run the calculation is probably no greater than with the period method, for simple tables will be published and printed in the oil papers that can be cut out, enabling quick readings to be made. Even without the table the calculation is easy with the few royalty rates, two or three, which would be used. In this method, the amount paid in royalty declines gradually, rather than suddenly as in the period method.

Jan 6, 1915

By Rosewell H. Johnson

Discussion of the paper of ROSWELL H. JOHNSON, presented it the San Francisco meeting, September, 1915, And printed in Bulletin No. 102, June, 1915, pp. 1291 to 1294. WILLIAM A. WILLIAMS, San. Francisco, CaI.-A sliding. scale of royalties was proposed to the Department of the Interior in connection with the fixing of royalties to be charged upon oil leases made on the Osage Reservation in Oklahoma. The possibility of evasion and difficulty of enforcement required close inspection to satisfy all interests, particularly in connection with the exemption from royalty on oil to equal maintenance and interest on the junk. Mr. Johnson discusses the block method, the period method, and the cumulative method, and favors the adoption of the cumulative method with a proviso that the wells should be permitted to be pumped until the gross income is as low as the maintenance cost, which would mean exemption from royalty on the smallest wells. He recommends that depth be the variable factor upon which the sliding royalty is based and suggests that on partially developed territory in the Osage, the royalty be one-sixth for oil wells averaging less than 2,000 ft. in depth, one-eighth for wells from 2,000 to 3,000 ft., and one-twelfth above 3,000 ft.; for the rest of the Osage he suggests one-eighth above 2,800 ft. and one-twelfth below that depth. The net result, if Mr. Johnson's suggestions had been accepted in the Osage, would have been to reduce the then existing rate of royalty and considerably increase the cost of administration. The difficulties in determining the size of wells to be exempt and the possibility of obtaining oil at different depths in the same well might lead to complications which are avoided by charging a flat royalty as now universally charged throughout the United States. It is not uncommon to reduce the royalty when the production of the wells becomes unprofitable at an existing rate of royalty, accomplishing very much the same results as Mr. Johnson has attempted to accomplish by the cumulative royalties, and probably in a manner far more satisfactory to the operator and the lessor. A. C. MCLAUGHLIN, San Francisco, Cal.-The net revenue of the well depends, first, on the cost of production; second, on the amount of oil produced; therefore it would be impossible under Mr. Johnson's system to set a royalty which would be fair to all concerned. If it is impossible to set it at the beginning, it is certainly further impossible to do it from day to clay. I think it is entirely impracticable of application.

Jan 12, 1915

By John H. Nicholls

In this paper, Imperial Oil Limited reports briefly on the drilling by contract rigs of twenty-nine slim holes in the Virden, Smiley, and Souris Valley areas. The investigations showed that slim-hole penetration rates, as a result of careful control of drilling variables, can approach those achieved with 7 7/8-inch bits. It is concluded that slim-hole drilling is acceptable for development or exploratory work. Imperial also reports on the completion techniques and equipment that have been developed on twenty-seven tubingless 2 1/2-inch casing completions. Indications are that the method is economically desirable where excessive gas or water production is not anticipated.

Jan 1, 1958

By W. D. Freeborn

Slim-hole drilling and completion techniques were first used in the Cynthia area of the Pembina field, Alberta, by the Texaco Exploration Company in the summer of 1957. Prior to that time, eighty-eight wells had been drilled and completed in this area in a conventional manner. Subsequent to the initial four-well evaluation programme, twenty-one additional wells have been drilled using slim-hole techniques. No difficulty was encountered in the drilling and completion of slim-hole wells, or in obtaining production from them. A comparison of drilling and completion economics and practices has been made for slim-hole and conventionally completed wells. Penetration rates for both bit sizes (614 in. and 9 in.) were relatively equal. The shorter life of the smaller bits required the use of 15 per cent more bits per well, but the total trip time to change bits was similar for both hole sizes because of the higher hoisting speeds possible with the lighter drilling strings used in the slim holes and better hole conditions. Completion costs of the slim holes were reduced by 37 per cent as compared to the costs of conventional-type completions. This was made possible through the use of smaller well equipment, the elimination of tubing, and a reduction in rig time for completion operations.

Jan 1, 1958

Of late there have been various papers published on this subject by various authorities, in which certain definite factors influencing slime settlement have been brought forward. As the principles set forth by these writers are of great interest, and have, in most cases, been generally accepted, the author will review them in the hope that by discussion some more knowledge may be brought to bear on many points connected with the subject.The definition of slime at the present time is not a standard one, and varies according to different authorities, some defining slime as ore crushed to such a fineness that it will pass through a screen of standard size, say 150 or 200-mesh, in water (1, 2);others as that part of the finely-crushed material which is in the physical condition which causes it to remain in. suspension in water, and possesses pr?perties which render it almost unleachable (3). Authorities seem divided on this point, but of late American writers seem to prefer the former definition. On the contrary, B L Gardiner describes slime as a mixture of small particles of crushed ore of varying sizes which, when mixed with water, tend...

Jan 1, 1912

By A K. Bhatnagar, S Saha, P Dixit, A K. Mukherjee, P Patra

TATA Steel’s R&D Division at Jamshedpur has developed a slime beneficiation process to recover iron values from iron ore slime. This process recovers iron ore concentrate containing 2.2 per cent alumina from a feed containing 7–10 per cent alumina. The reject generated from beneficiation of iron ore slime is treated as waste as the iron content in the reject is below 45 per cent. Effective utilisation of this waste is required for making the iron ore slime beneficiation process a zero-waste technology. In this connection several studies were made towards utilisation of slime waste. One of these studies revealed that slime waste can be used as a soil conditioner. Slime waste contains particles of size less than 10 micron and when these particles are mixed with soil in definite proportions, the porosity and the permeability of the mixture goes down. As a result, the water holding capacity (WHC) improves. This concept was evaluated through a series of tests at greenhouse level to optimise the soil to slime ratio. Finally, a pilot scale field trial was carried out over a period of three months using paddy rice as the crop. Three separate plots with compositions of: soil + organic matter comprising Farmyard Manure (FYM), (ii) soil and slime waste (2:1) + organic matter (FYM), and (iii) soil and slime waste (2:1) + organic matter (FYM) + Nitrogen, Phosphorus and Potassium (NPK) fertiliser were used for the pilot trial. The results showed a 20 per cent increase in the productivity of paddy rice for plot (ii) as compared to plot (i). This was due to the beneficial effect of slime waste in the soil. The addition of inorganic fertiliser such as NPK in the ratio of (4:2:1) further enhanced the productivity of paddy rice.

Sep 18, 2023

By George J. Young

(San Francisco meeting, October, 1911.) THE nature of slimes handled in the treatment of gold- and silver-ores has been discussed in technical literature to a considerable extent. The subject of slime-filtration from the practical worker's stand-point has also received much comment, and scattered through the literature of the subject are descriptions of many slime-filtration installations. Articles of this nature serve a valuable purpose and assist materially in the design of new and the improvement of old plants. The subject of the physics of slime-filtration has been touched upon to only a slight extent. The underlying principles are worthy of more intensive study and experimentation than they have received, and the main purpose of this paper is to present the results of such study and experimental work as will serve to make clear in part at least many of the principles which control the filtration of slime. Nature of Slime. Much has bean written concerning an accurate definition of the term ? slime," but no comprehensive definition seems to be generally accepted. The reason for this is clear. A slime consists of at least three different substances, each, when separated, possessing distinctly different physical and to a certain extent chemical properties. These substances are extremely fine sand, a colloidal material which may be and generally is in a coagulated condition, and a colloidal material which is in a non-coagulated condition. Suspending a slime in a relatively large volume of water by shaking and allowing sedimentation to take place, results in the fine sand settling out with comparative rapidity, followed by the coagulated material, which settles much more slowly and finally a certain portion remains

Nov 1, 1911

By C. E. Cairnes

The Slocan mining camp in Kootenay district; British Columbia; has long been noted for the great number of its silver-bearing deposits; and for the success that has; in many instances; attended their development. The orebearing area lies east of Slocan lake and mainly within a radius of 6 to 8 miles of the mining town of Sandon. Within this limited area 135 or more properties have shipped ore in quantities of from 100 tons or less to more than 500; 000 tons; and with a total value in silver; lead; and zinc ranging from a few hundred dollars to well over $10; 000; 000. Of the three metals; silver has easily ranked first in value; with lead second and zinc third. Zinc production; however; made slow progress in the early years; and with . the exception of the Lucky Jim mine; and a few others where high-grade ore could be readily hand-sorted; was a detriment to the silver-lead ores until improved methods of separation enabled it to take an important place in the mineral production of the Slocan.

Jan 1, 1954

By D. H. Xiong

Low grade oxidized iron ores are usually not economic to utilize. However, the development of SLon magnetic separators and other new technologies make the process cost lower and lower. In this paper, several low-grade oxidized iron ore process flowsheets are introduced. The key procedure is that at the early stage, SLon magnetic separators are applied to discharge as more tails as possible with very low cost, only a small portion of rough concentrate going to the cleaning stage, showing the new technologies are profitable for such iron ores.

Jan 1, 2014