Search Documents

By M. Razavi

This investigation is part an overall investigation on the effect of sodium silicate on the properties of the mine backfill. The results presented will highlight the effects of binder dosage, sodium silicate concentration, and pulp density on the performance of stabilized sodium silicate-fortified sand pastefill samples. Binders implemented for these experiments consisted of cement, slag, and sodium silicate in various proportions. The binder content varied from 3 to 9 wt% (total dry weight) and sodium silicate concentrations was adjusted at 2 and 4% (total binder weight). Moreover, pulp density was adjusted to values between 80 and 83 wt%. For completion of the aforementioned phase of the study, series of sand pastefill test samples were prepared and cured for 28, 56, or 120 days, in a humidity and temperature controlled room. The specimens were tested for uniaxial compressive strength (UCS). In order to study the effect of sodium silicate on microstructures of stabilized sand pastefill, some MIP tests were conducted on selected samples. The results of this investigation evaluate the use of sodium silicate as a partial replacement of cement in stabilized backfill. The analyses of the results demonstrates that, with an increase in binder content and a decrease in pulp density, the UCS values of sand pastefill samples increase. Further more, the results indicate that increase in addition of sodium silicate does not necessarily result in higher strength minefill.

May 1, 2007

By F. P. Hassani, Jacque Ouellet, M. Hossein

A laboratory investigation was undertaken to evaluate the effectiveness of different binding agents in a paste backfilling operation suitable to be used in a sulphide-rich environment. Different combinations of Portland cement and fly ash type C as well as ferrous slag were used as the binding agents. The unconfined compressive strength of the samples was measured for extended curing periods. The results indicate that the addition of 3% slag in the binding agent mix could produce strengths up to 0.5 MPa in the samples under investigation. For higher binding contents, the addition of Portland cement will lead to higher availability of calcium hydroxide and calcium aluminate, which are susceptible to deterioration from the phenomenon known as sulphate attack. Using slag, on the other hand, will reduce the permeability, availability of calcium hydroxide, and dilute the calcium aluminate ions reducing the susceptibility of the samples to sulphate attack. However, gypsum will form which could have the same detrimental effect on the strength of the treated matrix. Therefore, special attention must be given to the content and properties of agents used to activate the pozzolanic properties of the slag.

Jan 1, 2001

By Pei‑liang Xu, Jun Wang, Xi Zhang, Deng‑pan Qiao, Tian‑yu Yang

The surface backfill, serving as the operational platform for continuing mining in upward slicing and filling stopes, is required to possess sufficient strength and thickness. Currently, there are limited model methods for determining the strength and thickness of the surface fill body. By analyzing the mechanical actions on the surface backfill, it is determined that its stability is mainly influenced by the combined effects of normal and tangential uniform loads under full-load conditions of trackless equipment. Assuming a circular contact surface between the tire of the trackless equipment and the surface backfill, and utilizing solutions from elastic mechanics theories such as the Boussinesq and Cerruti solution, the stress and displacement distribution of the surface fill body were obtained. Based on the maximum vertical stress condition, where the surface backfill body undergoes maximum deformation while still in an elastic state, and considering the stress–strain relationship, a model for the strength and thickness of the surface backfill has been established. According to the research findings, the design for the strength and structural parameters of the surface backfill has been developed to meet the full-load operation of the Atlas ST7 scooptram, with a compressive strength of 1.32 MPa and a thickness of 0.5 m. Numerical simulation analysis results indicate that the stress and displacement of the surface backfill align with theoretical analysis results. Practical results from industrial application in the western section of the Dahongshan Copper Mine demonstrate that the designed strength and thickness of the surface backfill meet the operational requirements for trackless equipment, resulting in significant engineering application effects and economic benefits. The research findings hold significant importance for advancing the theory of backfill mining and have high applicability and promotional value for similar mines.

Mar 24, 2024

By H. Akgun

Design of plugs for abandonment of boreholes and shafts may be governed by the bond strength between the plug and host rock. This paper presents the results of push-out tests on cement grout plugs in salt. Two expandable cement grouts have been tested. The average interface shear strengths ranged from 2 to 12 MPa. Peak shear stresses at failure, assuming an elastic stress distribution along the interface, were up to eight times higher. Standard deviations commonly reached 20%. Dissolution along the interface was observed, and may have been enhanced by clay inclusions in the salt. This dissolution appears to have reduced bond strengths. Application of the results to the design of plugs for larger openings (e.g. shafts, drifts, or boreholes) is discussed.

Jan 1, 1991

By M. L. Jeremic

Altered and unaltered coal from the Star-Key Mine near Edmonton, Alberta has been tested under compression and under tension. The test results showed that altered coal samples have an appreciably lower strength than unaltered coal. Altered coal samples do not give a linear load-displacement curve, peak strengths are poorly defined and yielding is observed over a range of loads, so the material can be regarded as relatively plastic. However, unaltered coal samples produce a linear loading curve with a high tangential modulus and an easily distinguished peak strength at which there is a sudden brittle failure. These findings lead to important differences in the theoretical design of ribs and pillars in underground mines in the two coal types. The substantial differences in the strength properties and behaviour of the two types of coal are governed by a higher intensity of cracks in the weathered coal. Two causes of the additional cracking can be suggested-subaerial weathering and subterranean weathering of the coal.

Jan 1, 1979

By B. Amadei

INTRODUCTION Laboratory studies on the deformability and strength of intact rocks generally involve the uniaxial compression test, the standard triaxial compression test and direct or indirect tension tests. If [al ,a2 ,a3] are principal stresses [(al>a2>a3)] with compression taken as positive and tension taken as negative, the applied stress field for each one of these tests can be represented as shown in Fig. 1. However, for most in-situ conditions, such as those that exist at any point around an underground excavation, the stress field is truly three-dimensional or multiaxial [(al+ a2+a3)] and none of the tests shown in Fig. 1 can be used to predict the mechanical behavior of the rock. There are special cases for which one of the three principal stresses vanishes. Biaxial loading of rocks in-situ takes place, for instance, when rocks deform and fail in plane stress conditions. This can occur in a free unloaded surface of a rock structure such as in the wall of an underground excavation or a rock slope. Parallel to the free surface, the stress field components can be both compressive [(al>a2>0)], both tensile [(O>a2>a3)], or mixed, one component being compressive and the other one tensile [(U~>O>U~)]. The purpose of this paper is to present the results of 25 true biaxial tests that have been conducted on cubical specimens of Indiana Limestone using the multiaxial cell available at the University of Colorado at Boulder. The tests include uniaxial compression and tension, biaxial compression and combined biaxil compression- tension. Flexible fluid cushions and brush bearing platens were used for compressive and tensile loading respectively in order to minimize loading end effects on the test specimens. The paper begins with a review of previous investigations on the multiaxial behavior of rock. Then, test results are presented in terms of

Jan 1, 1984

By James I. Mathis

Should an arbitrary reduction factor be applied to laboratory compressive strengths when designing pillars? The answer is, as is the main contention of Peng's article, probably not. Many factors affect the strength of the material remaining in the pillar. On the other hand, outside influences will influence the strength testing results from the lab. This is not the first article, nor the last, to discuss the discrepancy between the two strengths. As was discussed in the article, actual pillar strength is affected by several factors. The two mentioned were: • The scale effect of discontinuities. How large must the pillar be so that the increase in discontinuity count with size will not decrease the strength. • Non-uniform strengths and lithologic units within the pillar. The scale effect of discontinuities is important. What size block must be tested so that the rock mass strength is actually measured? For a highly fractured rock mass, or coal with a high cleat density, this sample may be quite small. Conversely, if an unaltered, moderately jointed, quartz monzonite was examined, the sample block would likely be very large. This is the subject of ongo¬ing research. More to the point, if the tested sample is sufficiently large to model the rock mass strength, then no reductions should be made in the lab strength based on this factor alone. Non-uniform strengths and variations in lithologic units will also affect the pillar strength. I am not an expert in coal mines, having gained my experience in hard rock metal mining. These problems, though, are commonplace. However, strength sampling for pillar strength determination involves sampling material from within the lithologic unit that will form the pillar, not from pieces of material found on the floor. In addition, this sampling should cover the entire range of strengths of the material in the pillar-hard units (such as the partings described by Peng), as well as soft units. Testing results should then be included in the pillar design. Contrary to statements in Peng's article, at least one rock mass rating system (Laubscher, 1990) allows for the compositing of strong and weak units into a design rock mass strength that can be used for pillar design.

Jan 1, 1993

By Piotr Malkowski

Studies on the properties of rocks heated to high temperatures are rather rare. Such research is occasionally conducted for example; in areas around nuclear power plants. The national Polish coal gasification (underground coal gasification, or UCG) project has, however, forced the analysis of the geomechanical properties of heated rocks in the vicinity of a designed geo-reactor. Ukrainian experience with UCG show that rocks up to 2 m from the burned coal seam be at a temperature > 600ºC. Such a high temperature will undoubtedly influence their physical properties. This paper presents studies on the strength and deformation properties of carboniferous rocks in the Upper Silesian region, where the UCG process is planned. Three types of rocks were tested: claystones, mudstones and sandstones. Laboratory tests of these rocks evaluated compressive strength, elastic modulus and weight loss. An evaluation of the results of the tests comparing the thermal conductivity of rocks and their specific thermal capacity was then carried out. All of the rocks studied were heated to 300, 600 and 1000ºC, and also evaluated at room temperature. This procedure shed new light upon the behavior of heated rocks in relation to their distance from the designed geo-reactor. The test results presented were developed within Research Task No. 3 ?Developing a technology of coal gasification for efficient production of fuels and electric power?, financed by The National Centre for Research and Development under strategic research and development programme ?Advanced Technologies for Energy Generation.?

Aug 1, 2013

By Pan, Jian, Siwei Li, Deqing Zhu

"It is great significance to realize the efficiently and comprehensively utilization of iron, manganese and aluminum from refractory high-aluminum and high-manganese iron ores. Aimed at the two types of low grade refractory iron ores, mineralogical characteristics were studied. The direct reduction behaviors and evolution of mineral compositions of single iron ores and their blended ones were analyzed, and the corresponding reduction mechanisms were demonstrated. The results showed that only a part of iron oxides in high-aluminum ore are transformed to metallic iron after reduction, while the other react with aluminum and silica to form fayalite and hercynite which are difficult to be reduced. For the high manganese iron ore, most iron oxides can be reduced to metallic iron and manganese oxides can combined with aluminum-silica minerals to form galaxite and tephroite, promoting the reduction of iron oxides. Co-reduction results demonstrate that reduction of high- aluminum ore can be promoted by adding with high-manganese ore. Metallization and metallic iron grains increase dramatically by elevate high-manganese blending ratio. At the ratio of 60% high- manganese iron ore in the pellet feed, iron-slag separate well with a slag assaying 28.51%~36.35% Al2O3 and the recovery of iron and manganese can be reached 93%, respectively. The high-aluminum rich manganese residue was recycled with H2SO4. INTRODUCTION The growth of the Chinese iron and steel industry has been pushed forward by its rapid economic development in recent years, and 1126 million tons of iron ore have been consumed in 2014, where 933 million tons were imported according to the data from World Steel Association [1]. However, iron resources are limited, and especially the reserves of high-grade iron ores are declining, so it is of significant importance to optimize the mining rate of iron resources [2] and to utilize low- grade refractory iron resources, such as high-aluminum iron ore."

Jan 1, 2018

By Xiang-dong XING, Zhen-yang wang, Xing-le LIU, Jian-Liang Zhang

Experiments were carried out by adding CaF2 as catalyst in a Ar atmosphere to study the isothermal reduction kinetics of vanadium titano-magnetite carbon composite pellets under high temperature in the range from1473 to 1673K. By analyzing reduction mechanism, it was found that the rate controlling step was gas diffusion, and the activation energy was 178.39kJ•mol-1 without adding any catalysts. Adding CaF2 of 3% to vanadium titano-magnetite carbon composite pellets can decrease the apparent activation energy of reduction, and the decrease extent was 14.95kJ•mol-1. In addition, temperature is an important factor influencing on reaction rate.

Jan 1, 2015

By Xuling Chen, Zhiyun Ji, Min Gan, Wenqi Li, Xiaohui Fan, Zhiyuan Yu

"Specularite and vanadium-titanomagnetite are difficult to granulate, and with the increase of their proportions, the permeability of sintering bed is deteriorated together with the combustion velocity of fuel for the shortage of air through the sintering bed, which can lower sintering speed and specific production capacity significantly. The biomass fuel has a higher combustion velocity than coke breeze, therefore the productivity of specularite and vanadium-titanomagnetite ore can be improved remarkably by replacing coke breeze partly with biomass fuel .The results showed that, when the proportion of biomass fuel replacing coke is 40%,the sintering speed and specific production capacity of 35% specularite were improved from 19.06mm/min, 1.33 t/(m2·h)to 21.45mm/min, 1.47 t/(m2·h),and that of 55% vanadium-titanomagnetite were improved from 17.23mm/min, 1.11 t/(m2·h)to 22.80mm/min, 1.44 t/(m2·h). As a conclusion, biomass fuel is effective to strengthen sintering of refractory iron ore.IntroductionThe iron and steel industry of our country has achieved significant development in the recent years. In 2010, the output of steel has reached to 0.627 billion tons. The increasing scale of iron and steel has led to rigorous domestic iron ore environment, and the reserves of hematite and magnetite that have superior sintering characteristics are on the decline with continually exploiting and utilizing [1]. Therefore, the RIO (refractory iron ores) SP (specularite) and VT (vanadium-titanomagnetite) have to be applied vastly. However, the quality of sinters can be deteriorated when utilizing RIO in high proportion due to their poor granulation and metallogenic performances [2, 3]. Generally, the ratio of SP is 3~5%,which should not exceed 10% in our country currently [4]. Though high rate of VT is adopted in PZH steel for a long time, the productivity is obviously low compared with normal sintering [5]."

Jan 1, 2012

By Dao Su, Kelang Mu, Yufeng Guo, Jinghua Zeng, Tao Jiang

"The influence of high pressure roller grinding (HPRG) on sintering of iron concentrate fines was investigated. Results of mini-sintering tests showed that assimilation temperature of iron concentrate fines decreased from 1230 ? to 1220 ? and assimilation time was shortened from 10 min to 5 min when the iron concentrate fines was pretreated by HPRG. Sinter pot tests showed that the yield of sinter increased from 60.33% to 72.92% , tumble index increased from 44.35% to 46.66%. The investigation indicated that, after being pretreated by HPRG, iron concentrate fines are improved in ballability and the fraction of fine particles increased, resulting in the improvement of granulation property and reactiveness in solid state reaction. As a result, sintering of iron concentrate fines were strengthened.IntroductionWith the rapid development of iron and steel industry and the decrease of high-grade ores, the imports of iron ore are increasing continually. It is of immensely strategic importance for development of iron and steel industry and energy security in our country to make good use of iron concentrate fine which is low price, high grade and has a refractory sintering property. When iron concentrate fine is used in sintering, granulation property of sinter mixture and permeability of sinter bed get poor. As a result, yield and quality of sinter fall down. Many researches show that, when HPRG is used in pelletization, quality of pellets is improved dramatically. Meanwhile, HPRG has a low energy consume, a large handing capacity and it is benefit for environment protect. At this theme, strengthening of sintering of iron concentrate fine pretreated by HPRG was investigated in this paper."

Jan 1, 2012

By Syd S. Peng

In the past few years, the numbers of underground coal mines in this country using longwa11 mining method have been dramatically increased. In the latest count there are approximately 90 10ngwa11 faces amounting roughly 8% of the total underground production. Meanwhile, shortwall mining adapting longwa11 powered supports to 'coal mining and handling systems in room and pillar mining is also gaining importance in the Appalachian coal field. Although there are only 7 operating shortwall faces so far, indications are that it will be increasing steadily. Modern longwall faces are highly mechanized and productive. One of these key elements that contribute to the success of modern longwall mining is self-advanced powered supports. There are several types of powered supports. Frame type is two sets of one to four hydraulic legs supporting beam-type roof canopy and floor base. However, chock type is more popular and connected to broad roof and base structure. Shield supports were introduced recently but proved to be highly successful (1). A shield support consists of two hydraulic jacks mounted between a base plate and a gob shield. The base plate is hinged to gob shield which is in turn hinged to roof canopy.

Jan 1, 1977

"Acid resistant brick lined autoclaves and related vessels are utilized in pressure oxidation for the recovery of gold, copper, and other metals. The combination of the corrosion resistant membrane, acid resistant brick, mortar and steel shell is a composite system that requires a sophisticated stress analysis. In order to obtain meaningful results both the model and physical properties of the materials must be carefully selected. Evaluation of the calculated results requires an understanding of both the failure mechanisms of ceramics and experience with the performance of existing lining systems.INTRODUCTIONAcid brick lining systems are used in pressure oxidation autoclaves and related vessels to provide thermal and mechanical protection for corrosion resistant membranes that are applied directly to the interior of the vessel shell. The acid brick and mortar must be resistant to the process conditions and must provide a mechanically reliable structure.The construction of lined vessels incorporates a wide range of materials that can include the carbon steel vessel, austenitic weld overlay, lead lining, organic membrane, ceramic brick, mortars and other alloy components. The physical properties of the materials can vary by orders of magnitude and when combined in the construction of the lined vessel create a complex composite structure. The materials may be bonded together or act independently of each other. Stresses are induced into the lined vessel include pressure, thermal expansion, chemical expansion and mechanical loads.The complexity of these systems makes it is very difficult to account for all of the variables in the structural analysis of lined vessels. Historically calculations were simplified and designers primarily relied on experience with previous applications.The greatly improved tools for Finite Element Analysis (FEA) available today allow for detailed calculation of the stresses imposed on the vessel shell and lining. Koning & Lauzon (2004) presented a paper on design fundamentals including a discussion on the application of FEA methods at Pressure Hydrometallurgy 2004 in Banff. When a designer carefully constructs a model and selects the correct materials properties for the calculations, meaningful and useful results can be achieved."

Jan 1, 2012

Flat jack stress determinations in selected colliery roadways have revealed a range of measured stress from 330-p.s.i. tension to 3,750 p.s.i. compression. Photoelastic examination of loaded plastic and actual rock mo.odel mine openings has shown that the primary horizontal stress required to attain these measured stresses would be from one to three times the superincumbent vertical load.Examination of roof movement with a. borehole oxtensumeter and a series of anchors at various horizons to 30 feet in a. vertical roof borehole showed that when a standing face waa.s advanced the roofmovement was practically confined to the lower two feet. The ma.j ority of this movement occurred during the 36 hours after mining at this face commenced.The use of a. radioactive isotope and a. scintillation counter in a. pair of parallel bcreholes promises to be sensitive and accurate method of roof bedding plane crack detection.

Jan 1, 1963

Flat jack stress determinations in selected colliery roadways have revealed a range of measured stress from 330 lb/sq. in. tension to 3,750 lb/sq. in. compression. Photoelastic examination of loaded plastic and actual rock model mine openings has shown that the primary horizontal stress required to attain these measured stresses would be from one to three times the superincumbent vertical load.Examination of roof movement with a borehole extensometer and a series of anchors at various horizons to 30 feet in a vertical roof borehole showed that when a standing face was advanced the roof movement was practically confined to the lower two feet. The majority of this movement occurred during the 36 hours after mining at this face commenced.The use of a radioactive isotope and a scintillation counter in a pair of parallel boreholes is a sensitive and accurate method of roof bedding plane crack detection.INTRODUCTIONA knowledge of strata stresses is required to understand the deformation of an underground opening and, in particular, the roof behaviour. It is the aim of investigations currently being conducted by Australian Coal Association (Research) Ltd. to determine the stress existing around mine openings and the location and magnitude of roof movement.STRATA PRESSURE MEASUREMENTMost measurements of strata stress are performed at the surface of underground openings and the majority measure the change of strain resulting from stress relief. The accuracy of the measured value of stress depends upon knowledge of the rock modulus of elasticity. The flat jack method has the advantage that strain relief is restored by a measured stress applied directly by the jack. The rock modulus of elasticity can also be determined.

Jan 1, 1963

By A. H. PH. D Wilson

Compared to the rocks encountered in, say, metalliferous mining or tunnel drivage in igneous and metamorphic rocks, the strata associated with the coal measures are relatively soft. If excavations are made at depths greater than one or two hundred metres, zones of fractured or yielded rock develop around the openings. The stress which can be taken by yielded rock at the boundary of an opening is low, but because of the friction present between the fragments or particles, the sustainable stress rises rapidly with distance from the opening until sufficient confinement has been developed to prevent failure of the rock in the first place. Thereafter the laws of elasticity will apply and increasing distance will reduce the stress field until conditions consistent with the cover load are reached. For rocks which maintain their elastic condition right to the edge of an opening, finite element analysis and similar techniques have proved successful in determining the distribution of stress around the opening. This approach, however, is not successful when a yield zone is introduced between the elastic zone and the opening. Nevertheless, some estimate is required if help is to be given in the siting of roadways and in the determination of adequate pillar sizes. This matter is of particular importance in the planning of new mines especially if retreat faces are involved, as extensive roadway drivage must be planned and executed before experience of the effects of face extraction is gained. In 1977, the author published [I] a method based on 'stress balance'. The total aggregate downward load over a large area will remain that of the cover load even after part of the coal seam has been removed. Any rise in stress in ribsides and pillars must be offset by an equivalent stress reduction across roadways and other areas of extraction, and vice versa. Knowledge of one can lead to an estimate of the other, provided the general form of the stress distribution can be postulated. It is the object of this paper to revue the method in more detail and to give further examples of its successful application.

Jan 1, 1981

By Mark Lawshe, Shosie Serata

The conventional method of mining underground, using narrow rooms and wide pillars, has proven to be poorly adapted to the powerful earth forces that act on underground openings. The high costs of roof bolting, timbering, steel arching, and other means of artificial roof support for both room-and--pillar operations and longwall gate roadways attest to the limitations of traditional mine design. Too often, productivity halts when corners buckle under "cutter roof' stresses, floors heave, and roof strata fall. In the 1960s, an entirely different approach to strata control was developed. The Stress Control Method (SCM) stabilizes failing roofs and heaving floors by removing the cause of failure - highly concentrated stresses around the openings. This is achieved by regrouping three to 10 rooms into a single entry where the rooms are separated by very narrow yielding but stable pillars. SCM employs a specified excavation sequence to redirect earth pressures away from the mine openings. The yield pillars act as scaffolding until a permanently protective secondary stress envelope forms around the entry (lower part of Fig. 1). The result is a dramatic improvement in roof stability and a significant reduction in artificial support costs. Some roof bolting must still be done, mainly to meet Mine Safety and Health Administration (MSHA) requirements. Potash, salt, coal mining The stress control method was first applied to the deep potash mines of Saskatchewan. The new SCM design actually increased room widths to enlarge the stress envelope, redistributing the stress concentration away from the entries (Serata and Schultz, 1972). This resulted in a turnaround from pervasive roof fall/floor heave conditions that threatened operations in the eight new mines opened in the Saskatchewan potash field during the 1960s. In addition to eliminating all roof bolting, SCM successfully stabilized ground conditions and substantially increased productivity over the original design (Serata, 1976, 1982). Similarly, the deep Boulby potash mine of Yorkshire, England, was about to close after various conventional means of combating roof failure had failed. An SCM test area was excavated that resulted in the ground quickly stabilizing without need o artificial support (Serata, 1982; Chilton and Laird, 1982). Another example is the Diamond Crystal salt mine in Louisiana. Here, multiple level mining was being extended from the third to the fourth level downward in the Jefferson Island salt dome. Extensive roof failure was occurring at 396 m (1300 ft) ii the third level. SCM design principles in creased the room size from 24 to 49 m (80 t( 160 ft) on the fourth level at a depth of 457 m (1500 ft). This unprecedented expansion of room width was first questioned and later ap¬proved by MS HA, which expressed satisfaction in seeing the improvement documented by field validation data in 1973. The most recent SUM application to salt mining has been in the Michigan Basin a: Goderich, Ontario. The anticipated abandonment of Domtar Chemicals Group/Sifto Salt Division's deep operation in bedded sale was prevented by a multi-year SCM implementation. The success of SCM in dry mining[lecc] to its application to solution mining of salt This adaptation of the method is now being implemented in bedded salt at Fort Saskatchewan, Alberta by Dow Chemical Co., and in St. Clair, MI by International Salt Co. Application of SCM to solution mining in a salt dome is proceeding at Napoleonville. LA by Dow Chemical. The same technology has also been applied to cavern design for the Louisiana Offshore Oil Port (LOOP), and the compressed air energy storage (CAES)

Jan 1, 1989

By J. L. Luo, D. G. Ivey, A. H. Adeleke

Double-edge-notched flat tensile samples of X70 steel were used for both slow strain-rate testing (SSRT) and cyclic loading testing with the notch located in the zone of interest, i.e., the weld metal (WM), base metal (BM) and heat affected zone (HAZ). By using both optical and scanning electron microscopy, the stress corrosion cracking (SCC) behaviour with respect to crack morphology and various forms of microstructure was investigated. In all the samples considered, the mode of failure was predominantly transgranular with cleavage facets around the edges of the fracture surface. The BM, with a bainitic microstructure, had the highest resistance to SCC when compared with the mixed microstructures of acicular ferrite-primary ferrite and acicular ferrite-grain boundary ferrite observed in the WM and HAZ, respectively. The effect of microstructure on stress corrosion cracking behaviour is discussed based on experimental observations.

Jan 1, 2005

By G. Bylapudi, A. Bhagwat, K. Mondal, A. J. S. (Sam) Spearing

Minimizing the effects of corrosion improves the long-term performance of the rock anchors and ground control systems in underground mines, which is fundamental for safe operation over the design period. The primary objective of this study is to explain the problems due to stress corrosion cracking (SCC), strain-induced corrosion cracking (SICC) and other forms of corrosion, and why the mining industry’s ground control professionals should take this into serious consideration. It is important to clearly determine the kind of SCC mechanisms that causes roof bolt failures in order to suggest the necessary action plan to mitigate or eliminate the possibility of the cause. Pertinent literature and studies around the globe on this complicated subject are reviewed. The secondary objective is to encourage the use of corrosion-resistant ground control products in the underground mining industry in areas of high corrosion potential. Characteristics of SCC on high strength steel are also reviewed. The literature and preliminary studies to date indicate that research work is necessary in United States.

Jan 1, 2015