Search Documents

By C. Kim

The integration of three-dimensional (3D) data with infrared thermography has received much attention for its potential use as input data for building energy simulations. Therefore, researchers have proposed methods to integrate 3D data with infrared thermography obtained by different sensors. These studies show the potential of the integration of 3D data and infrared thermography using various systems. However, these studies have ignored property aspects of infrared thermography, such as the low resolution of infrared thermography and external environmental influences. Thus, their proposed methods to integrate 3D data and infrared thermography are inadequate because these problems can affect the resulting building energy simulation. This research proposes a framework that integrates infrared thermography and 3D data while accounting for the resolution and shadow effect of infrared thermography. The proposed framework consists of three steps. In the resolution enhancement step, bi-cubic interpolation is proposed. In thermal data correction from the shadow effect, the shadow area is detected from the visible image, and then the shadow effect is removed from the registered infrared thermography. Finally, enhanced infrared thermography is mapped to the 3D data obtained by a laser scanner. The performance of the proposed framework was evaluated using test images obtained from a building in operation. The experimental results show that the proposed framework provides a 3D thermal model that is useful and accurate in simulating building energy. It is expected that the 3D thermal model can be used for accurate energy simulation of existing buildings. In addition, the proposed framework can be applied in defect detection for buildings. Furthermore, this novel approach enhances infrared thermography using visible images.

Aug 1, 2013

By Pentti Niskanen

"The ventilation system of the Pyhasalmi Mine is described. The mine is located in an area where the annual atmospheric temperature may vary from +30°C to -30°C. Natural ventilation causes serious difficulties because the underground mine is connected by drifts and finger raises to the bottom of the 120 m-deep open pit.The natural ventilation tends to make the ventilation net unstable. The paper describes how the instability characteristics of the ventilation net can be studied and how they have been taken into account when automating the control of the ventilation. In addition, the software, hardware and costs of the system are described. The system consists of 12 automated ventilation doors, two mine fans, 8 elements for sensing the air flow and temperatures, a control panel and a process computer."

Jan 1, 2014

By F. M. Ramadhan, M. R. Pratama

Monitoring open-pit mine road conditions has become very critical nowadays. There are several benefits to in conducting research on this field such as opportunity to improve truck’s speed which directly influences truck’s productivity. This research aims to provide a semi real-time, and sensors-based automatic road damage detector that predicts the road quality through road damage exact location tracing, road damages auto-classification, and real-time instruction in the form of work order format to mining road maintenance, and repair authorities through mobile apps and maintenance unit’s in-cabin display. It will also provide the maintenance/repair activity performance evaluation via integrated dashboards. The artificial neural network algorithm is applied during the process of data training regarding classifying road damages and severities which resulted in a valid model. The road damage classification model has a precision level of 80.5% in predicting whether the road is damaged or not. Using this approach, we are expecting to visualise a road quality map of all active roads on mine site.

Sep 1, 2021

By J. M. Rebstock

Recent re-classification of crystalline silica as a potential human carcinogen has resulted in a new limit of 0.1% free silica in bulk powdered minerals. Detection of silica at this level can be expected to severely challenge or exceed the capabilities of existing protocols for x-ray diffraction, the traditional method for free silica determination. Automated SEH-EOS analysis provides an attractive alternative method, with direct analysis of individual particles for the determination of the concentration of free silica, and a direct measurement of silica particle sizes. This paper will discuss automated SEH analytical procedures, sample preparation, and statistical considerations.

Jan 1, 1990

By D. Chetty

The characterization of platinum group minerals (PGMs) from concentrator flotation circuits provides valuable information towards understanding PGM recovery under given milling and flotation conditions. Additional mineralogical characterization also provides information on ore variability, which may affect recovery. Considering the low grades involved, automated scanning electron microscopy (SEM) characterization of PGMs has enabled relatively quick analyses, compared with older, time consuming and less accurate optical microscopy methods. Over the years, parameters, such as species, size distribution, liberation, gangue and base metal sulfide (BMS) associations, have been used to characterize the PGMs in a process mineralogical context, to aid metallurgical interpretation. This paper considers whether flotation indices determined for PGMs can be empirically validated, using initial results from analysis of PGMs in a concentrate bank from a South African concentrator treating UG2 ore from the western limb of the Bushveld Complex. The aim is to determine whether floatability is adequately described by these parameters, or whether other mineralogical factors must be considered when assessing PGM floatability, and hence accounting for recovery vs. losses to tails. The data obtained to date, show that flotation parameters (including liberation index, BMS/gangue relationships and size distribution) have merits where large changes in PGM concentration occur, as observed in the first four cells of the concentrate bank. Larger data sets, however, are required to assess floatability, particularly where concentrate cell grades are similar, as observed in the last six cells of the concentrate bank. Furthermore, the floatability indices could be enhanced by the incorporation of selected associated gangue mineral information, chief amongst these being the content and mode of occurrence of naturally floatable talc and associated orthopyroxene.

Jan 1, 2009

By J. Gallegos, R. Faber, T. Cox

"An innovative method to reduce acid rock drainage (ARD) and sediment loading of a recreational lake was used in the Red River watershed in northern New Mexico. The Red River drains a mining district that contains multiple naturally occurring hydrothermal alteration zones that release ARD and sediment to the river during episodic summer rain storms. A lake is near the mouth of the watershed and is filled with water from the river through a sluice gate and diversion. An automated actuator was installed on the sluice gate to close when the river is impacted by high-suspended sediment. Water quality probes were installed at the sluice gate to monitor the river water for turbidity, specific conductivity and water depth. If high turbidity is measured, the sluice gate closes automatically. Remote access is setup with a computer view screen to review the real-time system status. Once the turbidity drops below a threshold, the sluice gate is reopened remotely. The automated sluice gate has successfully reduced the amount of ARD and suspended sediment entering the lake. This reduction has resulted in an improved aquatic habitat for the fishery and benthic macroinvertebrate community. BACKGROUND The Red River is located within the Sangre De Cristo Mountain Range in northern New Mexico. The river drains an area of approximately 190 square miles and spans elevations from 6,600 feet at its confluence with the Rio Grande to its headwaters near 12,000 feet (Figure 1). The river generally flows to the west along most if its length.The Red River watershed includes several hydrothermal alteration zones. The alteration zones were created by intrusion of high-silica granites and subvolcanic porphyries, with associated hydrothermal fluids, into the volcanic rocks of the Questa Caldera. The hydrothermal alteration is also responsible for the molybdenum deposits in the area. Rapid chemical weathering and physical erosion of pyrite-rich hydrothermally altered rocks has resulted in the formation of alteration scars. The alteration scars are characterized by steep, erodible slopes with little vegetation and incised gullies. Debris fans from the drainages containing active alteration scars have formed and typically consist of poorly sorted sand and gravel that is distinctly pale yellow in color. Some of the more prominent scars are located in the Hansen, Straight and Hottentot Creek drainages downstream of the town of Red River."

Jan 1, 2018

By M. K. Elmouttie, G. V. Poropat

Mapping of exposed rock walls provides data on geological features such as joints, bedding planes, faults etc critical to the economics and the safety of mine operations. Traditional, manual methods of mapping can be time consuming, error prone and limited in their coverage. New methods have been developed to map exposed faces remotely and safely however the benefits of these methods are only fully realised when exposed structures can be quickly and easily mapped using automated methods. This paper describes the application of an automated method of analysis of 3D images that provides users with the capacity to map exposed structures automatically. The method is based on the use of vector classification methods used in some neural network systems and provides rapid and reliable identification of exposed planes. CSIRO Exploration and Mining is applying these methods to 3D images for a range of applications from pit mapping to machine automation.

Jan 1, 2006

By J M. F Clout

Geological, textural and mineralogical classification of iron ores is routinely conducted by mine and exploration geologists on reverse circulation percussion, blasthole cone and bulk samples for grade control, defining ore and waste, determining lump:fines ratio and predicting downstream processing characteristics. Classification is based on physical hardness, colour, streak and other visual characteristics. However, logging is generally restricted to the five to 20 per cent of chips above about 2 mm. This means that most of the sample is too fine to be reliably logged for anything but colour or streak and the textural types must be inferred from other information. A recently developed software package called æRecognitionÆ allows automated identification and classification of iron ore textural types and gangue on a particle basis in polished section down to 0.01 mm using processed digital images. It is not designed to be used as a routine logging tool, but is applicable where higher definition is required at the resource evaluation stage on selected percussion, drill core or bulk samples. æRecognitionÆ processes data obtained after optical image analysis of fine iron ore samples. It contains several parts, like æRecognitionÆ, æCompositionÆ, æLiberation by Total IronÆ, æLiberation by PhasesÆ and æStatisticsÆ, which allow vast and diverse information to be obtained about the iron ore samples being studied. Identification and classification of the textural type of each particle is performed according to the CSIRO-Hamersley Iron Ore Group Classification Scheme. The recognition procedure encompasses a good knowledge of different ore types and a logical knowledge tree, managing fuzzy boundary problems and the potential for a few different ore types in the same particle to be considered. This new technology introduces strict criteria to make the process of identifying particles more objective. Automated recognition standardises the identification procedure and significantly saves time. It enables users without a strong background in mineralogy to perform accurate texture identification. The æRecognitionÆ package has a modern user-friendly interface and Word compatible output. The combination of all the features mentioned makes the package a convenient tool for detailed studies of fine iron ores.

Jan 1, 2005

By G. K. Palshikar

Mining operations offer many opportunities for the use of IT and communication technologies to improve automation and thereby deliver higher levels of productivity, cost, quality and safety. In this paper, we discuss a particular application, namely, building a fully automated train control and operation system within a mining area. We first outline the basic architecture and functionality of such a system and then present a real-life case study where the railway system within a remote iron ore mine in Canada was converted to a fully automated train operation system. This hard real-time safety-critical system required the use of advanced technologies such as embedded systems (e.g., on-board train controller), radio communications, formal methods, optimal scheduling, and extensive simulations. We focus on the design aspects for maintaining the system in safe states.

Sep 1, 2012

By M J. Thurley, L Lindqvist, D Degerfeldt, J Nyström, R Nordenskjöld

Rock breakage is a major component of all mining and mineral processing operations with the particle size distribution linked to productivity through the comminution chain. Optimisation and automatic control of comminution, material handling, and agglomeration processes is a complex task with large potential for gains in productivity, and energy efficiency. A key factor in realising these gains is the requirement for fully-automated online particle size distribution measurement to provide the necessary feedback and input for control. Moreover, to enable automatic control system it is necessary to provide a consistent, reliable size distribution measurement that avoids the significant errors resulting from under-sizing overlapped particles and over-sizing clusters of fine particles. Published literature and observation of commercial systems indicate a body of predominantly 2D photographic based particle size measurement systems that suffer from a number of significant errors except in the simplest case of a monolayer of particles under good illumination with limited colour variation in the material. In order to overcome these limitations a university and industry collaboration developed three-dimensional particle measurement (3DPM) between 2006 and 2012, based on 3D surface profile measurement of the visible material on conveyor. 3DPM avoids particle delineation errors due to variation in material colour and shadows, detects overlapping versus non-overlapping particles, and identifies areas of fine particles as fines and not large rocks. 3DPM measures: the visible material and calculates its particle size distribution, bulk volume, detects boulders, and conveyor belt fill factor in an automated consistent manner. Furthermore, 3DPM’s advanced algorithms allow observation of particle variation that would otherwise be undetected without the capacity to identify visible areas-of-fines and overlapped particles. Boliden Mines has installed 3DPM at three operations for measurement between the stockpile silo and grinding mill, and measurement after the primary crusher. Fragmentation measurements across multiple years of measurement are presented with some observations of plant behaviour. In the future 3DPM results will be incorporated into automatic control strategies for plant optimisation. 3DPM is used across a wide range of material types and applications that also includes; limestone aggregate for quality control in manufacturing, agglomerates for closed-loop automatic control in chemical production, and measurement of coke for size-based blending feed control to the blast furnace in steel production. CITATION:Thurley, M J, Degerfeldt, D, Nyström, J, Nordenskjöld, R and Lindqvist, L, 2018. Automated, online measurement of bulk material size distribution on conveyor using 3D profile imaging at Boliden Mines, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 641–652 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By T E. Tibbetts

This paper deals with coal sampling in general and with mechanical coal sampling in particular. The necessity of obtaining representative samples is emphasized. Other sections of the paper are devoted to the design and selection of automatic samplers, with a consideration of the three main types, and the testing, operation and maintenance of these samplers. The cost of the installation of an automated sampling system must be related to the value of the material to be sampled, to the volume of coal involved, and to the savings in labour and economy which can be achieved. Introduction T HE Committee?:; on Coal Sampling of the Coal Study Subsection, Thermal Power Section (Eastern Zone), Canadian Electrical Association, was established in November, 1963, to "study the various problem areas of coal sampling." The first undertaking of the Committee was to at-tempt to survey the problem areas of coal sampling through an evaluation of coal sampling difficulties as experienced at both the plant design and operational levels within the electric utilities represented on the Committee. The results of this enquiry indicated that satisfactory answers to almost any conceivable

Jan 1, 1965

By Andreas Gaich

A new 3D fragmentation analysis method for muck piles is presented. It works with aerial imagery from UAVs (drones) and handles entire muck piles with minimum user intervention.

Feb 1, 2020

By L. S. Almeida, U. A. Courbassier, C. T. Guimãaraes, M. N. Souza, V. L. Silva, H. P. Dias, G. A. Bicalho, B. S. Rocha, P. N. Rodrigues, A. Carnevale

During primary aluminum production the anode changing is a very important task. So improvements on it will be essential to avoid disturbance and have a better operational control. After anode changing a good current distribution will be guaranteed using a cavity cleaner and precise anode setting. Albras switching a manually anode setting to an automatic one solved the setting problems. In this paper it will be shown some pot line results and the improvements on workers ergonomic and safety conditions. The device was developed in a partnership between Albras and Pesto.

Jan 1, 2006

By Thierry Bernard

New technology to automatically design a blast based on autonomous drone. The process of flying a drone, calculating the 3D cloud of points, generating the critical face profiles and placing holes automatically according to burden specification becomes fully automatic. A nice time saving with more efficiency

Feb 1, 2020

By F. Sundqvist, B. Skawina, J. Greberg, A. Salama, M. Astrand, P. Ekbeck

Today’s mining operations require fast reporting and rapid rescheduling based on updated information. An automatic mine scheduling system could not only quickly reschedule but also propose alternative solutions. To avoid the financial and physical risks associated with testing such a system directly in operation, it could be first evaluated via discrete event simulation models. This would offer a safe environment to evaluate different operating rules and algorithms. In this study, this is achieved by integrating automatic scheduling software with a discrete event simulation model.

Jun 1, 2021

By Felix Wunsch

WHILE the effect of the cold-junction temperature has been known by many, its consideration has been ignored in a number of installations, resulting at tunes in a very considerable error. In fact, the magnitude of this error may amount to over 100° in some cases. While hand-operated correcting devices for portable checking pyrometers may be entirely satisfactory, it is, of course, desirable to have such apparatus en¬ Millivoltmeter Thermocouple Platinum Wire Mercury FIG. 1.-EARLY `METHOD OF AUTOMATICALLY COMPENSATING FOR COLD-JUNCTION TEMPERATURE CHANGES. tirely automatic, when applied to curve-drawing or printing pyrometers, otherwise there is no assurance that the record is correct. Numerous methods for automatically compensating for cold-junction temperature changes of thermocouples have been proposed and used in connection with millivoltmeters. One of the earliest proposed was that shown in Fig. 1. A bare resistance wire was immersed in a column of mercury located near the cold junction of the thermocouple. An increase in temperature near the cold junction resulted in a rise of the mercury column, which short-circuited more of the resistance wire causing an increase in the potential difference across the millivoltmeter, which compensated for the decreased electromotive force of the thermocouple.

Jan 9, 1919

By CK Tsang, Jack Muir, Dharman Gersch, Joshua Barry

Correct face pressure is critical to safe operation of a closed face TBM. If inadequate face pressure is applied, this will lead to excessive ground movement, and may result in collapse of the tunnel face. Face pressure calculations are performed manually every few meters along the tunnel alignment. With the application of a 3D ground model, ground profile information can be extracted for automatic computation. This will significantly improve the efficiency and accuracy and is adaptable to changes in design parameters. This paper will discuss the development of automatic computation techniques in extracting information from a 3D ground model.

Jun 13, 2021

By A. L. Mular

"IntroductionSince the mid -1960s, automatic control of grinding circuits has become the rule, to avoid losses attributable to frequent circuit upsets associated with uncontrolled disturbances such as ore hardness variations. Higher capital costs of grinding equipment and corresponding operating costs-especially with respect to energy consumption-are major factors that continue to stimulate interest in grinding control.Grinding circuit control strategies depend upon the control objectives defined by the processing plant and are subject to constraints such as: maintain final per cent solids within some range, do not transport steel ball s out of the discharge trunnion, or do not overflow or empty the pump box and so on. Constraints depend on the nature of equipment employed within the grinding circuit and may actually determine the characteristics of the control scheme. Typical control objectives are:1. Maintain final particle size at set point by ,a. manipulation of fresh feed rate with circulating load maintained by manipulation of pump box water addition rate, orb. manipulation of pump box water addition rate with circulating load maintained by manipulation of fresh feed rate, where the methodology utilized to accomplish either (a) or (b) is dependent upon equipment/circuit constraints such as the availability of a variable speed pump.2. Maintain circuit throughput at a maximum by,a. manipulation of fresh feed rate subject to constraints on final particle size and variables such as power draw, circulating load and mill overload.3. Maintain mill load at set point by a. manipulation of fresh feed rate subject to constraints such as on power draw.4. Maintain mill power draw at set point bya . manipulation of fresh feed rate subject to mill load constraints. Often, a grinding control objective is dictated by the recovery vs fineness-of-grind characteristic that exists for downstream separation circuits. When recovery is relatively insensitive to size, maximum throughput in the grinding circuit is advantageous.The purpose of this paper is to review control strategies for primary ball mill grinding circuits, rod mill/ball mill grinding circuits and semi-autogenous grinding mill circuits. Primary sensors employed are highlighted and modern trends are documented briefly."

Jan 1, 1989

By Leonid Pevzner, Valerie Dmitriev, Yuri Babitchev

Performance of belt conveyors, service life of belts and mechanical elements can be radically improved if the automatic adjustment of the belt speed movement is made in such a way, that the unit load over the conveyor length be constant and close to the rated one under random input freight traffic. Such an adjustment is possible when the system of a controllable thyristor electric drive on the basis of induction squirrel cage motor is used. Computer-aided adjustment of the belt conveyor movement is effected via bicontour digital control of the main drive in order to redistribute loads when the loading of conveyor and contour of the control of tension drive are changed. The system envisages control and condition monitoring of the conveyor electromechanical system, as well as metering of electrical power and the amount of conveyor freight. The results of the simulation of speed control of the conveyor belt are given in the report. Mathematical model of the conveyor electromechanical system describes the movement of the belt with cargo and the tension drive. The input cargo traffic is assumed as stationary ergidic random process with the assigned characteristics. The solution of the problem of the synthesis of a closed-loop control system, the structure and parameters of adjustment, the conditions of asymptotic stability of the control back-up system and the condition of minimization of mean square error of shadowing are also given in the report. Microprocessor controller is used to realize the function of the adjustment unit. Under this control system standard mode of conveyor operation, different modes of start-up, operating mode with decreased speed when transporting people, service and emergency braking of a conveyor and some other modes are realized. The digital model of a conveyor as an instrument for decision making in case of emergency is used in those modes. MASTER TEXT Long-standing practice of belt conveyor operation in mines of Russia has proved their inefficient use with 40-70% capacity and 20-25% availability factor. It is associated with unreasonable power intensity and reduction of service life of mechanical components, and as a result, with the growth of total transportation costs. Low efficiency of conveyor application can be explained by the extremely irregular distribution of conveyor freight traffic. Usually, the width of a conveyor belt is identified in accordance with the possible maximum traffic value, engine power capacity for long-term operation under rated loads. However, actually a conveyor often runs without any load and its average load in most cases is lower than the rated one. The problem can be eliminated by way of the adjustment of the operational mode of a conveyor according to an actual input freight traffic via belt speed control providing for the conveyor regular linear load which is nearly equivalent to the rated one. Experimental research into freight traffic under working conditions of the operating underground and open-cast mines proves the fact that the actual freight traffic can be adequately presented through the model of stationary random function of time, for ex- ample, as a J (t) continuous random Gaussian process that is modulated with a G(t) elementary pulse flow:

Jan 1, 1996

By W. TRINKS

RAPID progress has been made in the automatic control of open-hearth furnaces in the past few years and many firms today\supply such control apparatus. It is somewhat surprising that so little was heard about open-hearth control up to about, 1928, and that thereafter the practice of automatically controlling open-hearth furnaces spread very rapidly. Before discussing the reasons for this it may be advisable to list the quantities that can be controlled. One of the easiest quantities to be controlled in the open-hearth furnace is pressure. The reasons for controlling it are plain. If there is excess pressure in the furnace, products of combustion leak out around .the .door and through all the cracks in the brick-work. The stability of the piers between the doors is seriously endangered, and front wall repairs become frequent. Furthermore, hot gases are lost that might be usefully employed in heating the checkerwork. If there is a slight vacuum in the furnace, cold air entering through the doors and cracks cools the interior, slowing down the reactions and making it impossible to secure the highest degree of preheat from the checkerwork.

Jan 1, 1931