Search Documents

By Stewart W. Daniel

"Increasing labour costs, the trend to larger mills, the processing of lower grade ores and a diminishing sup-ply of well-trained and experienced mill operators contribute to the necessity of automating a grinding circuit. With sophisticated process control techniques, supervision of the mill line is reduced to an occasional inspection by the shift supervisor. Process operating decisions and/or adjustments are quickly and accurately performed by the electronic devices to be described. When the variables in the grinding circuit are stabilized using the sensors and controllers as discussed, the over-all grinding circuit is maintained at its optimum grinding load level, with ample protection against under-and overloading."

Jan 1, 1967

By P. Lenegan, R. Masethe, R. I. L. Ferreira

Underground mining in high rock-stress environments can induce unanticipated dynamic rockmass deformation, posing a serious risk to the workforce. Data collected by seismic networks are imperative for the design-as-you-mine process. Often an inappropriate assessment of the seismic hazard is done when unnecessary data are included in analytical techniques, particularly short-term time frames. Depending on the methodology or application of data analysis and interpretation, some of the information may not be relevant and even detract from the objective. By using the spatial event clusters associated with active workplaces to define the shape and size of the polygons for data selection for subsequent analysis, a problematic subjective component can be eliminated. The mining of tabular reefs in South Africa, be they gold- or platinum group metals, is very extensive, and underground workplaces are often widespread. Production stoppages are very costly, especially for marginal mines, so there is just cause not to evacuate an entire operation’s workforce following the occurrence of a large mining-induced seismic event. A rationale based on the damaging peak particle velocities (PPV) of the past seismicity can exclude the unaffected underground personnel and allow a quick orderly withdrawal where required. Micro-deformation may precede rockbursting, which can occur on-shift close to the workface. A mine-wide array of geophones suitable for the accurate location and analysis of seismicity may not be able to detect these higher-frequency emissions. Inexpensive but fit-for-purpose accelerometers, providing real-time, continuous measurement of acoustic rockmass deformation near the workplace, integrated through underground and surface communications networks, are shown to record ‘rock-talk’, clearly distinguishable from the instrument background noise, which can be in the order of hours leading up to an imminent damaging seismic event.

Jan 12, 2025

By Peter Ay, Harry Pempel, Satya Narra, Mike Müller, Jens Markowski

"Within the next few years major changes in mobility are expected. Increasing numbers of electric powered cars, electrobikes and E-Scooters define the transport sector. Recently lithium based traction batteries as storage medium have led into matrurity of series production combining high electrical efficiencies with low weights and compact dimensions. Due to the relatively young development with lithium batteries utilization, only few investigation were conducted regarding their recycling. Conventional battery recycling processes can not be applied due to differences in design and chemistry. So an automated disassembly and processing procedure for lithium traction batteries has been developed in the R/D-project ""Li-WERT"". Instead of complete smelting of the batteries without pretreatment, an automated disassembly and specific treatment of the material streams was realised, adjusted to the needs of the subsequent recovery technologies. A higher quality, with reduced expenses for the separation of fine-grained or fused material mixes, can be obtained for the individual components. The automated disassembly using an industrial robot significantly reduces dangers for the operating crew. The selective disassembly and beneficiation allows full recovery of the fractions. The batteries will be disassembled to cell level by the industrial robot. Anodes, cathodes, and separation layers are isolated and processed. The technology is designed, that no waste is generated for disposal. The pelletised cathode coating and the other separated metals (stainless steel, copper, aluminum) can be used in respective metallurgical plants. Circuit boards and plug contacts are also coveted secondary raw materials for reuse. The process is modular and offers high flexibility, e. g. for new battery types/ sizes by quick adjustment of the robot and tool change. Adaptation to other cathode materials (e. g. Li[FePO]) is possible. After finishing the R/D-project, a pilot plant for demontage was realised in 2013."

Jan 1, 2014

By L. G. Morrell

Introduction A Self-Dumping cage which combines the features of a small skip and a cage has been used in a vertical winze between the 2,000 and 2,500 levels at the Coniaurum mine for the past three years, during which time its success has been demonstrated by uninterrupted service and low maintenance charges. lt was designed by John Reddington, mine manager, and was built under his supervision in the Coniaurum mine shops. Being new in many of its operating features, a small-scale model was made and tried before the final construction was undertaken. The mechanical performance of the model suggested a few minor changes that were incorporated in the final drawings. During its three years of use, the automatic dumping device has saved the expense of deck-handling of the cars. This actually represents a gross economy of something over four times the cost of construction and installation, which totalled $1,325. The cage, empty, weighs 2,200 pounds, of which 500 pounds represents the weight of the dumping accessory and necessarily heavier construction. Besides a considerable financial saving, the time saved in unloading increases the daily hoisting capacity of the winze. In raising ore from the 2,500 level, five minutes are required for a complete trip. Allowing one minute for the alternative of decking, we believe that the automatic dumping has increased the capacity of the winze hoist nearly 20 percent.

Jan 1, 1933

By Adabala Raja Venkata Sai Naresh, Radhakanta Koner

Particle size distribution (PSD) is an essential parameter in assessing the overall efficiency of blasting operations in mines and the subsequent mine-to-mill process in the mining industry. Despite some drawbacks of 2D image analysis techniques in accurately estimating particle sizes in PSD, the mining industry has relied on them for the last three decades. This study proposes the 3D rock fragmentation measurement (3DFM) technique for deducting the accurate dimensions of 3D rock particles for the PSD. 3DFM has utilized different processing algorithms. Images of different views of the non-touching rock particles of varying sizes have been acquired as a data acquisition step of structure from motion technology for generating sparse point cloud. Dense point cloud reconstruction is used to avail finer details of the point cloud using clustering views for the multi-view stereo algorithm. Random sample consensus (RANSAC) algorithm coupled with an unsupervised classification using the density-based spatial clustering of applications with noise (DBSCAN) classifier is employed to extract the rock clusters from the 3D point cloud. Finally, the accurate rock sizes are derived using the hybrid bounding box rotation identification (HYBBRID) algorithm with a root mean square error (RMSE) of 0.10 cm for length, 0.10 cm for breadth, and 0.32 cm for depth. The PSD of rock fragments obtained from the proposed 3DFM technique is found to be matching with the results of mechanical sieving and manual gauging with an R2 values of 0.98 and 0.99, respectively. The 3DFM method can be considered cheaper, more accurate, and computationally faster in determining the rock dimensions for the PSD determination method to enhance the productivity of the mining industry.

Dec 29, 2023

By G. S. Brooks

DURING the past few years, the Mineral Point Zinc Co. has had under consideration the improvement of various types of gas-filtering apparatus used in the removal of dust from crushing and milling plants, in the manufacture of oxide, and on blast-furnace fume and sintering furnaces. The original equipment of the various plants of the company was, of course, along lines of the standard stationary bag house. These houses required large surfaces, hand shaking, and varied only in the manner of the collection of solids and in the distribution of the gas. Early in 1908, the first trial of a mechanical bag house was made at Nassau Plant at Depue, Ill. The duty of this installation was on dust-laden gas from a fine-crushing mill. The Printz and Rau bag machine was finally adopted and put into operation. This ingenious machine embodied what were then to us two novel features in bag-house practice: 1. An intermittent crinkling and snapping of the filtering fabric to free the meshes of solids. i 2. A reversal of gas flow for a short period by a temporary connection w th the suction trunk. This equipment worked fairly well except in cold weather, when we ran into condensation troubles. Had we at that time understood more fully some of the limitations of fabric filtering work, these might well have been remedied. We were impressed by this experience, however, with the efficiency of sudden tension on the fabric under suction. After a study had been made of some of the Western blast-furnace houses using the reversal-of-flow feature, experiments were started early in 1914 with a view to developing an automatic equipment along the best lines of our past experience. The objects sought were: 1. Keeping labor out of the houses for hygienic reasons. 2. Reduction of labor costs. 3. Reduction in -size of hag houses. 4. Accessibility. 5. Ability to handle relatively hot gases where required.

Jan 11, 1917

By G. Guzman

In the framework of the optimization of Teniente Converter operation the new system of automatic flux feeding through gar-gun was implemented in the Potrerillos Smelter, Codelco Chile, Salvador Division. The control algoritm based on simple iron and silica balance adjusted by empirical coefficients was incorporated in the logical programmer. The programmer works in real time gathering information from the plant instrumentation events and introduced chemical assays of concentrate, slag and flux. Through the auto-tuning of the automatic operation the criterions of optimal flux dosage were determined. Four month of operation of the automatic flux feeding system demonstrated the stabilization of magnetite content in the slag in the narrow range from 18 to 20% and the decrease of flux consumption, corresponding to annual savings US$ 340,000. Additionally, the automatic system helps operators in the control room in fast determination of optimal fluxing and avoid the errors in flux dosage affecting the slag quality and its impact on refractory wear.

Jan 1, 2007

By J. Lee

A monolithic caisson is one of the major structural components commonly used in the construction of docks, breakwaters, and container terminal quay walls. Since the structure of monolithic caissons is typical and somewhat simple, its design process is also typical and repetitive, but still time consuming. To reduce the total time and enhance productivity, we developed a parametric model in Revit to automatically generate a 3D model of a monolithic caisson. It is designed to generate the Revit model of a caisson with concrete body and reinforcing bars. The size of caisson, the number of reinforcing bars, and the space between reinforcing bars are automatically changed when users update parameters. This paper presents how we developed this parametric family in Revit for monolithic caisson design and how it would enhance its design process.

Aug 1, 2013

There are presently in use many grinding mill control schemes and concepts. This paper presents one operating method of controlling the particle size of the cyclone overflows for proper metallurgical results and controlling the level of the cyclone feed sump and new feed rate to obtain lowest unit cost of finished (ground) material which is usually at the maximum grinding mill throughput. This system stresses simplicity of field instrumentation and control strategy. Both of these factors lead to better operator understanding and acceptance. The low capital investment of this system also makes it more attractive at the Buick Concentrator when compared to other more complicated systems utilizing mass flow measurement and a computer to calculate circulating load and infer particle size. Furthermore, it has the advantage of utilizing an actual measurement for control, rather than a difficult-to-maintain inferred value. There are several reasons for maximizing mill throughput at Buick. The milling rate before automatic control was too low when compared to mill throughput increases planned for the future. Through this new operating system, it appears Buick will not have to make major changes of mill motors and speeds to meet the increased? production rate. Also, since power costs continue to escalate, it is desirable to maximize the throughput to the grinding circuit and reduce overgrinding to achieve a reduction in power cost per ton of ore milled. Presently, 45% of the concentrators' total power is consumed in this grinding circuit.

Jan 1, 1977

By Terry E. Perkins, Len Marnewecke

Installation of a relatively simple, low-cost analog mill control system at Amax Lead Co. of Missouri's Buick concentrator has paid off handsomely. The system, which provides the capability of handling mill circuit upsets and ore changes while maintaining a desired particle size, is expected to generate annually a return on investment of several times its capital cost. In addition, the system stresses simplicity of field instrumentation and control strategy, leading to better operator acceptance and understanding, and its capital cost makes it very attractive for the specific installation when compared to more complex schemes using mass flow measurement and computers for calculating circulating load to infer particle size. This system has the advantage of utilizing an actual measurement for control, rather than a difficult-to-maintain inferred value.

Jan 2, 1978

By Donald D. Murphy

My first contact with underground, bolt conveyors came when I was hired as a draftsman by the La-Del Conveyor & Manufacturing Company in 1935. At that tine relatively few nines were using haulage belt conveyors. Wore they were in use, they were usually loaded by chain or shaker type room conveyors which in turn were hand loaded at the working face. Duo to the low room tonnage, a gathering belt might receive who output of from six to eight rooms. For several years belts 26 and 30" in width were the favorites for coal mine use. Belt speeds very seldom exceeded 200 ft. per mm. at that time. Conveyor lengths for the majority of units lay between 1.000 and 2000 ft. For a number of years 25 H.P. drives were adequate for those conveyors. From 1940 until about 1950 loads and speeds went up slightly and 40 H.P. drives became the standard. Since the majority of mines were then using direct current power systems, we were able to use controllers with 3 or more steps of starting resistance. The slow belt speeds coupled with relatively long starting cycles kept the rate of acceleration low and gave us smooth, easy starts.

Jan 1, 1963

By William Petruk

A fully automatic image analysis system that consists of a microprobe, an energy dispersive x-ray analyzer, and an image analyzer was developed at CANME:I' to determine mineral behaviour that affects beneficiation. The interlacing between the instruments permits automatic identification and characterization of minerals in samples of unbroken ore pieces and of mill products. Different types of information are obtained for minerals in samples of unbroken ore pieces than in samples of mill products, and are used differently. For unbroken ore pieces size distributions are determined for discrete mineral grains to predict a grind at which they might be liberated, and other measurements are Irade to predict the percentage of mineral that occurs as nonrecoverable grains. For mill products the minerals are analysed to determine percentages that (1) are free, (2) are likely to be recovered in concentrates, (3) are likely to be lost to tailings, and (4) could be liberated with regrinding. The image analysis data for mill products are processed by a mineral-metals balance program to determine the distributions of free and unliberated mineral grains at each point in a concentrator, pilot plant or bench test. For samples containing trace minerals, such as gold, an automatic search technique is used to scan the entire area of the polished section for the trace mineral grains. The identified trace mineral grains are characterized with regard to size, liberation, and other properties.

Jan 1, 1988

By M. Leslar

Slope monitoring has been an important issue in static terrestrial lidar for some time. Several solutions for monitoring the progress of a slide have been devised over the years. All of these solutions have required users to be in the field operating the lidar equipment. This paper presents a new system developed using the Optech ILRIS-HD or ILRIS-LR lidar and the scripting language of PolyWorks to produce an autonomous slope monitoring system. This system has proven invaluable in detecting and alerting mine workers to potential danger within their mine sites. It has already been deployed in two mine sites and is scheduled to be installed at a third.

Feb 27, 2013

By K. Bommer

"In today’s fast paced, globally competitive world, reliability and machine uptime are of the utmost importance to a successful operation. Along with these targets more emphasis is being put on cost reduction and decreasing the environmental impact of the overall system. To achieve these goals, automatic lubricators and lubrication systems have been used in many industries for years and are now becoming a common tool in the mining industry as well. These systems are able to provide proper lubrication amounts at the proper times autonomously, helping to keep the machines running smoothly while minimizing the physical support required. Copper mines in the southwest have begun utilizing auto lubrication to avoid mistakes and unplanned shut downs on critical equipment. This paper will describe the engineering behind these products and review case histories where these tools have been successfully utilized in the mining industry. INTRODUCTION In a dirty, dusty, wet environment, where machine uptime is imperative, proper lubrication of bearings is the only way to survive. With the push for cost reduction and mines striving to lower their environmental impact and increase worker safety according to MSHA guidelines, the old lubrication practices have come under scrutiny. It is no longer encouraged or cost effective to have maintenance personal walk from point to point throughout the entire mine pumping a shot of grease into each bearing once per shift. Automatic lubricators and lubrication systems have been on the market for years but recently, as the market focus has changed and technology has developed, the use of these systems has begun to rise in the mining industry. Automatic lubrication systems can be as simple as a single point lubricator lubricating one (1) bearing or a more complex system lubricating numerous bearings. With system design, the automatic lubricator provides a preset amount of grease to a bearing at regular, predetermined intervals. The systems designed to lubricate more than one bearing contain grease pumps of some design and possibly PLC controllers which can be used to remotely adjust and monitor the system. As can be seen in Figure 1, the right amount of lubrication can be achieved much more reliably with automatic lubricators. Depending on application needs, the market now has products to fit almost every wish list. This paper is going to focus on the single point systems that are lower in cost but are still being effective."

Jan 1, 2015

By R. C. Miranda

The purpose of this work is to present ?state of the art? mass balances closing strategies in ore treatment plants. It presents a brief history of difficulties and challenges ahead. The current methodology is based on usage of an expert system, which seizes and filters the plant data, analyzes situations of equipment stops and mostly instruments failures. It is still possible to internally create a strategy to check the data of an instrument failure. The system is coupled to software with a Lagrangian model of mass balance closure that receives the pre-treated data. Thus, the data goes through filtering and reconciling processes to generate a reliable mass balance of the ore treatment plant. This made possible to obtain a system that is able to tell the real productivity of a ore plant through reliable mass balances. Residence times on equipments are critical to the balance, thus, they require good logic to eliminate errors due to the characteristics of non-steady state. Among the next challenges is the inclusion of a ?soft sensor? as a replacement of an instrument required for mass balance closure.

Sep 1, 2012

By O. C. Irwin

For several years the C. F. & I. Co. men have been working on a fan signal and many different schemes have been tried. I will describe a few of them. A make-and-break attachment was placed on the fan shaft which caused a light to flicker. A hinged door was placed on air course and counter balanced so that it would have a slight travel when the air pressure was reduced an appreciable amount. This motion was used to open the power circuit, blow a whistle, or ring a bell. Series transformers were placed in motor leads of fan drive motor and the variation in amount of power to motor was used to control the fan signal through a magnet or relay. A governor was placed on the fan shaft which opened a signal circuit when speed of fan was reduced. We tried to produce a machine actuated by the volume of air, (that is on the principle of the anemometer) but had to discard this due to its being too delicate. None of the above schemes seemed to fill the conditions which the State and our Mine Inspector wanted covered. They gave us the following demands for a signal: 1. Must open mine circuit and sound alarm when air pressure was reduced below a certain amount. 2. Must be fool proof. 3. Must work on any kind of fan drive (steam or motor). 4. Must be safe to ' install- in any mine or fan house. 5. Must not depend upon mechanical device which could become inactive due to friction or other causes. 6. Must be as simple and easy to adjust as possible.

Jan 1, 1925

IN 1932, the No. 4 shaft at Wright-Hargreaves mine was completed to a depth of 4,000 feet, and the lowest operating level at that time was at 3,900 feet. It was realized that the existing pumping system, using triplex plunger pumps at somewhat irregular depths in the mine, would be in-adequate to take care of the increasing volume of water that would have to be handled as mining operations expanded. Accordingly, in February, 1932, after a thorough study of the whole matter, it was decided to instal an entirely new, automatically controlled, system of pumping, employing centrifugal pumps, with their characteristically trouble-free performance, operated by off-peak power.

Jan 1, 1939

By K D. Conroy

For the past year, Lowphos Ore Ltd. has been operating two desliming hydroseparators on a fully automatic basis. Automatic operation is achieved by sensing the position of the silica-magnetite interface and automatically controlling the jet water addition to maintain a desired interface position. The system further provides automatic control of the underflow pump speed in order to assist in maintaining interface position when an <Ore change occurs. Interface position is maintained at 12 inches below the surface and is -controlled within plus or minus one inch. Metallurgical unit recovery is held above 98.5 per cent, and a 10 to 12 per cent increase in concentrate grade is normally achieved.

Jan 1, 1963

By M MacMillan

THE following is a brief description of the method of hoisting ore automatically at the No. 14 shaft of Mcintyre Porcupine Mines, Limited, Schumacher, Ontario. All ore and waste below the 3875-ft. level is hoisted up No. 14 shaft from the 7000-ft. level to the 3000-ft. level. Seventy to seventy-five per cent of the mining is done in this area. The shaft consists of four compartments: a man way, a ventilation compartment and two skip compartments. The hoist, located on the 3500-ft. level (see Figure l), is an 80-in.-diameter, 4-rope friction winder, utilizing two 6-ton front-dump skips in balance. The hoist is powered by a 1,100-h.p. A.C. motor, the maxi-mum speed being 2,400 ft. per minute. The operation can be either manual, push-button automatic from the pocket, or fully automatic. Men can be raised or lowered in the skips, using a collapsible aluminum platform placed inside the skip box.

Jan 1, 1963

By Kazmierczak J. B., Klein E., Kinscher J., Lizeur A., De Santis F.

In this work, we propose to implement machine learning methods for the automatic classification of mining-related seismic data. The approach retained for the classification is based on a Convolutional Neural Network (CNN) which has been tested and applied to two different mining datasets: the active ore mine of Garpenberg (Sweden), currently under exploitation, and the abandoned coal mine of Gardanne (France), where mining stopped in 2003. The first step of the approach consists in creating a well classified (manually) database of seismic signals separated in different classes as a function of the seismic sources. The selected database is then divided into two groups: train, containing the 70% of the signals, and test, which contains the remaining 30% of the signals within the selected database. The learning phase of the algorithm consists in creating a classification model based on the train group, which is further validated on the test group. The application of CNN for the automatic classification of Garpenberg and Gardanne seismic data shows, respectively, that about 88% and 98% of the seismic events of the two sites can be properly classified. These results demonstrate that machine learning could be a powerful tool for microseismic monitoring in mining and post-mining environments, which could be further extended to the whole automatic processing of seismic data, including signal’s classification as well as microseismic event’s localization.

Apr 26, 2022