Search Documents

By W. Rostoker

PART of a program of research on the Ti-A1 system1 involved a study of the lattice parameters of the titanium-rich a solid solution, which has a hexagonal close-packed structure. For this work, a 14 cm Debye-Scherrer powder camera and filtered CuK, radiation was used. For each pattern, the parameters were calculated by a least squares solution of the five strongest high angle lines. This provides an accuracy of i0.005A or better. The results are shown graphically in Fig. 1. It will be seen that an unusual change of slope occurs in the curve for the C parameter at high aluminum contents. Such anomalous changes in slope have been recorded by RaynorV or several magnesium-rich solid solutions. The effects were interpreted in terms of a special contribution to the lattice distortion due to factors of electronic origin predicted by Jones." Jones' theory, in substance, suggested that an unusually large expansion of the lattice would begin when the electron per atom concentration in the alloy was increased to a value at which an overlap just began from one Brillouin zone to another. Con-

Jan 1, 1953

By Tormod Forland

FROM equilibrium measurements on the system NaF-Na 3A l Fo-A 1 2 O 3-Na CO 3-CO 2 with high contents of NaF, Forland, Storegraven, and Urnesl concluded that complexes are formed containing two oxygen, three aluminum, and a less defined number of fluorine per complex. The same number of oxygen atoms per complex was also found by cryoscopic measurements for mixtures high in NaALF 6. In a recent paper by Stokes: some other complex ions, Al2O2F42- and AlOF2-, have been suggested. Here an additional argument in favor of the complex ALO2F. suggested by Forland, Storegraven, and Urnes will be given. When fused Na3AlF6 containing some A12O3, is cooled slowly, the solid phase will consist of the two components as separate phases. The melting point and the heat of fusion of Al2O3 are so high that this component will form the stable solid phase even though in the liquid state the complex may have a high stability. If, however, the fused mixture is quenched, the decomposition of the oxygen-containing complex and the formation of solid Al2O3 does not proceed fast enough, and a solid solution of A12O3 in Na3AlF6 is obtained. Zintel and Morawietz3 obtained cryolite containing 10 pct AL2O3 in this way. The density and the lattice parameters of the A12O3 containing cryolite were also measured, and from this it was concluded that the Al2O3 enters the cryolite lattice as Al3AlO0 groups replacing Na3AlF6 groups. However, the experimental data could as well be explained by assuming that one Na+ ion and two of its neighboring F- ions are replaced by one Al3+ ion and two O2- ions. This may be pictured schematically as: F F F F F F F Al F Na F Al F ,-Na+ + Al8+ F Al 0 A1 0 A1 F F F F —2 F- + 2O2- F F F solid cryolite cryolite-alumina solid solution This means that the complex in the solid solution, derived from X-ray and density measurements, is the same as that which Forland, Storegraven, and Urnes derived from equilibrium measurements in the liquid state. References IT. Forland, H. Storegraven, and S. Urnes: Ztsch. fur anorgan-ische und allgemeine Chemie, 1955, vol. 279, p. 205. 2J. J. Stokes: AIME Trans. To be pubhshed. s E. Zintel and W. Morawietz: Ztsch. pubhshed.fur anorganische und allgemeine Chemie, 1939, vol. 240, p. 145.

Jan 1, 1958

By Walter Rose

Experimentation which measures differences in pressure across the interfaces of immiscible fluids in the interstitial spaces of porous media may be termed "capillary pressure experimentation". In the literature of petroleum technology since 1941 there have appeared twelve papers popularizing capillary pressure concepts and developing applications of these concepts for the solution of problems of practical reservoir engineering importance, such as the determination of connate water, fluid distribution. in transition zones, reservoir rock textural properties, and oil recovery from petroleum reservoirs. Although a review of the literature would be justified at this time in order to reconcile the conflicting viewpoints which are contained in the cited papers, the object of this note will be of more limited scope. It is believed that the recent paper of Muskat alls sufficient attention to many of the uncertainties which arise upon examination of the published literature. such that until satisfactory counter-proposals can be made it will serve our purpose only to mention some other like uncertainties. This will emphasize further the need confronting petroleum technologists to re. consider and reformulate the application possibilities of capillary pressure experimentation. In particular, I sug- gest that we examine the thesis that capillary pressure experimentation as above defined can lead to measurements reflecting the recovery of oil from petroleum reservoirs, as was proposed first" by Amyx and Yuster and was first reduced to practice by the experimentation of Welge . In fact. I shall deal exclusively with the Welge papers since it is the principle one on this subject which has appeared to date. I shall attempt to show that the possibility of describing oil recovery features in terms of capillary pressure phenomena has not been established entirely. The Welge paper was a pioneering effort to evaluate this recovery application possibility. P. P. Reichertz' comments on the Welge paper state that non-wetting phase discontinuities are developed occasionally in the Welge experiment, and restate Muskat's argument that discontinuous fluid elements (partially saturating the interstices of porous media which are elsewhere saturated with some other immiscible phase or phases) are not subject to the requirements of hydrostatic equilibrium. It is the purpose of my comment to show that it is unnecessary to make Reichertz' postulation regarding non-wetting phase discontinuities (however valid) when it is desired to criticize Welge's theoretical treatment of his problem. It can be shown that Welge's method of measuring values for ''capillary pressure" is invalid in many instances of application, such that his reported curves of capillary pressure Versus fluid saturation often have no physical meaning, even throughout the interval of fluid saturation where it might be otherwise suspected that no phase discontinuities occur. By considering established principles of capillary pressure experimentation it can be shown that the pressure difference experimentally observed between wetting and non-wetting fluid phases which are contained in external reservoirs will reflect on the capillary pressure difference at the interfaces of contact between these phases only when the following conditions are satisfied: (a) There shall be a balance between the opposing forces of gravity and capillarity, as obtains under conditions of hydrostatic equilibrium when the positions of the interfaces of contact become fixed in pore spaces of certain geometry (b) The wetting and non-wetting fluids within the interstitial spaces shall everywhere be continuous with the external wetting phase reservoir and the external non-wetting phase reservoir, respectively. It will become apparent immediately that in any instance when a greater pressure is recorded in the external wetting phase reservoir than in the external non-wetting phase reservoir, one may establish either that static equilibrium has not been attained or that discontinuities in one or more of the fluids have been developed. This is because the pressure otherwiee is always gereatest in the non-wetting phase at each static interstitial interface of contact with the wetting phase. such that the externally measured pressure in the non-wetting phase likewise must be greatest if the above conditions are to be satisfied.

Jan 1, 1949

By Walter Rose

Experimentation which measures differences in pressure across the interfaces of immiscible fluids in the interstitial spaces of porous media may be termed "capillary pressure experimentation". In the literature of petroleum technology since 1941 there have appeared twelve papers popularizing capillary pressure concepts and developing applications of these concepts for the solution of problems of practical reservoir engineering importance, such as the determination of connate water, fluid distribution. in transition zones, reservoir rock textural properties, and oil recovery from petroleum reservoirs. Although a review of the literature would be justified at this time in order to reconcile the conflicting viewpoints which are contained in the cited papers, the object of this note will be of more limited scope. It is believed that the recent paper of Muskat alls sufficient attention to many of the uncertainties which arise upon examination of the published literature. such that until satisfactory counter-proposals can be made it will serve our purpose only to mention some other like uncertainties. This will emphasize further the need confronting petroleum technologists to re. consider and reformulate the application possibilities of capillary pressure experimentation. In particular, I sug- gest that we examine the thesis that capillary pressure experimentation as above defined can lead to measurements reflecting the recovery of oil from petroleum reservoirs, as was proposed first" by Amyx and Yuster and was first reduced to practice by the experimentation of Welge . In fact. I shall deal exclusively with the Welge papers since it is the principle one on this subject which has appeared to date. I shall attempt to show that the possibility of describing oil recovery features in terms of capillary pressure phenomena has not been established entirely. The Welge paper was a pioneering effort to evaluate this recovery application possibility. P. P. Reichertz' comments on the Welge paper state that non-wetting phase discontinuities are developed occasionally in the Welge experiment, and restate Muskat's argument that discontinuous fluid elements (partially saturating the interstices of porous media which are elsewhere saturated with some other immiscible phase or phases) are not subject to the requirements of hydrostatic equilibrium. It is the purpose of my comment to show that it is unnecessary to make Reichertz' postulation regarding non-wetting phase discontinuities (however valid) when it is desired to criticize Welge's theoretical treatment of his problem. It can be shown that Welge's method of measuring values for ''capillary pressure" is invalid in many instances of application, such that his reported curves of capillary pressure Versus fluid saturation often have no physical meaning, even throughout the interval of fluid saturation where it might be otherwise suspected that no phase discontinuities occur. By considering established principles of capillary pressure experimentation it can be shown that the pressure difference experimentally observed between wetting and non-wetting fluid phases which are contained in external reservoirs will reflect on the capillary pressure difference at the interfaces of contact between these phases only when the following conditions are satisfied: (a) There shall be a balance between the opposing forces of gravity and capillarity, as obtains under conditions of hydrostatic equilibrium when the positions of the interfaces of contact become fixed in pore spaces of certain geometry (b) The wetting and non-wetting fluids within the interstitial spaces shall everywhere be continuous with the external wetting phase reservoir and the external non-wetting phase reservoir, respectively. It will become apparent immediately that in any instance when a greater pressure is recorded in the external wetting phase reservoir than in the external non-wetting phase reservoir, one may establish either that static equilibrium has not been attained or that discontinuities in one or more of the fluids have been developed. This is because the pressure otherwiee is always gereatest in the non-wetting phase at each static interstitial interface of contact with the wetting phase. such that the externally measured pressure in the non-wetting phase likewise must be greatest if the above conditions are to be satisfied.

Jan 1, 1949

By C. G. Dunn, F. W. Daniels, M. J. Bolton

Recent observations on grain boundary movements in sihcon iron have indicated the possibility of studying grain growth phenomena in two-grain specimens in which several variables affecting growth are readily controlled. These variables are (1) the energy per unit area (?) in the grain boundary, (2) the orientation relationship of the two grains, and (3) the radius of curvature (7) of the moving boundary. Ideally, one grain A should be a narrow rectangular parallelepiped adjacent to a second grain ß as shown two dimensionally in Fig 1. Such a two-grain group becomes unstable when one end of grain A is shaped according to the dotted line. Since the width w of grain A remains constant during growth of grain B, T should also remain constant. The other vari- ables mentioned above can be controlled in the preparation of each two-grain specimen.l,2,3 For a parLicular orientation of each grain, is not necessarily fixed; ? may also depend on the orientation of the grain boundary, but this may be controlled to some degree. The energy relationships for the gowth of grain ß may be derived from the more simple arrangement of two grains A' and B' shown schematically in Fig 2. Here B' largely surrounds A'. Assume these grains are oriented with a common plane parallel with the flat

Jan 1, 1950

By Walter Rose

In a recent technical note, Owen Thornton&apos; suggests that wetting liquid relative permeability may be derived from the relationship: where Pd/Pc is the ratio of displacement pressure to capillary pressure at the wetting liquid satdration Sw, and I is the resistivity index at this saturation. Thornton shows that this expression gives values for relative permeability in good agreement with those experimentally determined by Leverett. We have recently developed another expression for krw which seems preferable to Equation 1 since it requires fewer experimental data for its verification. This equation may be derived in the following manner. Making use of the analogy between mass transfer of fluid in a porous medium and electrical conductivity through the fluid in the same medium, we can postulate a hydraulic formation resistivity factor analogous to an electrical formation resistivity factor. From Poiseuille&apos;s Law the resistivity to flow in a tube of radius R is of the form 8u/R², where is the viscosity of the fluid. Similarly7 the resistivity to flow in a porous medium of the same dimensions as the tube is given by D&apos;Arcy&apos;s Law as where k is the permeability of the medium. The hydraulic formation resistivity factor, Ff, is thus the quotient of these two resistivities, or: But permeability is defined by the KO-zeny equation as: where: r is the average pore radius of the porous medium, L. is the average tortuous length of the average pore, + is the porosity, and L is the bed length. This gives Fr as a function of the (La/L) .-.-.tortuosity ratio and porosity, or in explicit form: where: T = (La/L)&apos;, and N is the number of pores of radius, r, which will be found in any cross sectional area, x R&apos;. That is, N = R²/r². It will be clear from the foregoing considerations that the hydraulic formation fat. tor should be dependent on the value of R which in every case must be arbitrarily selected. By analogy, the hydrauiic formation factor, Fcf, characterizing the porous medium at Sw<1,will be given by: R² NT. where ke is the effective wetting liquid permeability obtaining at Sw<l, and Te is the square of the (Las/L) ratio defined by Thornton. Therefore, the hydraulic resistivity index, If, is: However, Thrnton gives I as: and it follows that: Equation 2, when checked against the data of wyckoff and Botset² and some of the Morse et al data³, gives comparisons as shown at the bottom of this page. Computations based on Leverett&apos;s data, quoted by Thorntaon, gives computed krw values somewhat lower than the experimental values. Moreover, other instances can be cited where we find that neither Equation 1 nor Equa tion 2 is checked by experimental data. The work of Botset&apos; on the Nichols Buff sandstone and Morse et a1 on oil wetted Bradford sandstone are such instances. A reason for these discrepancies may lie in the fact that if both Equations 1 and 2 are presumed always to give accurate values for krw, it follows that PC = Pd/Sw". Such an expression, it is well known, is too simple to describe accurately the capillary pressure behavior of all porous media. However, it is believed that a particular advantage resides on the use of Equation 2, since it is not dependent for its utility on a knowledge of the capillary pressures obtaining in dynamic flow svsterns. No practical technique for measuring the capillary pressures characterizing the fluid distributions in dynamic flow systems has yet been proposed. Acknowledgment is given to Dr. Paul D. Foote, executive vice-president of the Gulf Research and Development Company, for permission to publish this note. 1. Owen F. Thornton, "A Note on the Valuation of Relative Permeability," J. Pet. Tech., 1:7, Section 1, July, 1949. 2. R. D. Wyckoff arid H. G. Botset, "The Flow of Gas-Liquid Mixtures through Porous Media," Physics, 7:325-345, 1936. 3. R. A. Morse, P: L. Terwilliger, .and S. T. Yuster, "Relative Permeability Measurements of Small Core Samples," Oil and Gas J., 46:109-125, Aug. 23, 1947. 4. H. G. Botset, "Flow of Gas-Liquid Mixtures Through Consolidated Sand," Trans. AIME, 136:91, 1940.

Jan 1, 1949

By Walter Rose

In a recent technical note, Owen Thornton&apos; suggests that wetting liquid relative permeability may be derived from the relationship: where Pd/Pc is the ratio of displacement pressure to capillary pressure at the wetting liquid satdration Sw, and I is the resistivity index at this saturation. Thornton shows that this expression gives values for relative permeability in good agreement with those experimentally determined by Leverett. We have recently developed another expression for krw which seems preferable to Equation 1 since it requires fewer experimental data for its verification. This equation may be derived in the following manner. Making use of the analogy between mass transfer of fluid in a porous medium and electrical conductivity through the fluid in the same medium, we can postulate a hydraulic formation resistivity factor analogous to an electrical formation resistivity factor. From Poiseuille&apos;s Law the resistivity to flow in a tube of radius R is of the form 8u/R², where is the viscosity of the fluid. Similarly7 the resistivity to flow in a porous medium of the same dimensions as the tube is given by D&apos;Arcy&apos;s Law as where k is the permeability of the medium. The hydraulic formation resistivity factor, Ff, is thus the quotient of these two resistivities, or: But permeability is defined by the KO-zeny equation as: where: r is the average pore radius of the porous medium, L. is the average tortuous length of the average pore, + is the porosity, and L is the bed length. This gives Fr as a function of the (La/L) .-.-.tortuosity ratio and porosity, or in explicit form: where: T = (La/L)&apos;, and N is the number of pores of radius, r, which will be found in any cross sectional area, x R&apos;. That is, N = R²/r². It will be clear from the foregoing considerations that the hydraulic formation fat. tor should be dependent on the value of R which in every case must be arbitrarily selected. By analogy, the hydrauiic formation factor, Fcf, characterizing the porous medium at Sw<1,will be given by: R² NT. where ke is the effective wetting liquid permeability obtaining at Sw<l, and Te is the square of the (Las/L) ratio defined by Thornton. Therefore, the hydraulic resistivity index, If, is: However, Thrnton gives I as: and it follows that: Equation 2, when checked against the data of wyckoff and Botset² and some of the Morse et al data³, gives comparisons as shown at the bottom of this page. Computations based on Leverett&apos;s data, quoted by Thorntaon, gives computed krw values somewhat lower than the experimental values. Moreover, other instances can be cited where we find that neither Equation 1 nor Equa tion 2 is checked by experimental data. The work of Botset&apos; on the Nichols Buff sandstone and Morse et a1 on oil wetted Bradford sandstone are such instances. A reason for these discrepancies may lie in the fact that if both Equations 1 and 2 are presumed always to give accurate values for krw, it follows that PC = Pd/Sw". Such an expression, it is well known, is too simple to describe accurately the capillary pressure behavior of all porous media. However, it is believed that a particular advantage resides on the use of Equation 2, since it is not dependent for its utility on a knowledge of the capillary pressures obtaining in dynamic flow svsterns. No practical technique for measuring the capillary pressures characterizing the fluid distributions in dynamic flow systems has yet been proposed. Acknowledgment is given to Dr. Paul D. Foote, executive vice-president of the Gulf Research and Development Company, for permission to publish this note. 1. Owen F. Thornton, "A Note on the Valuation of Relative Permeability," J. Pet. Tech., 1:7, Section 1, July, 1949. 2. R. D. Wyckoff arid H. G. Botset, "The Flow of Gas-Liquid Mixtures through Porous Media," Physics, 7:325-345, 1936. 3. R. A. Morse, P: L. Terwilliger, .and S. T. Yuster, "Relative Permeability Measurements of Small Core Samples," Oil and Gas J., 46:109-125, Aug. 23, 1947. 4. H. G. Botset, "Flow of Gas-Liquid Mixtures Through Consolidated Sand," Trans. AIME, 136:91, 1940.

Jan 1, 1949

By Owen Thornton

Recently equations have been presented by Rose and Bruce&apos; and by Rose², showing how the relative permeability of a reservoir rock may be determined from the capillary character of the rock. In particular, equations were developed to show the relationship between capillary pressure and the effective permeability to the wetting phase in a poly-phase flow system. The equations are as follows (nomenclature the same as in the Rose and Bruce paper) Rose and Bruce assume that the average length of path (L,), which the wetting fluid follows in flowing through a porous media is independent of the saturation to the wetting phase, so that 1 is a constant dependent only on the k rock, and the permeability to the wetting phase is a function of the saturation and of the capillnry pressure: In measuring the flow of ekctric current through partially saturated core samples, it has been observed that the electrical resistance usually is not a simple linear function of saturation. This fact indicates that the average length of path in the flow of electric current is not independent of saturation, but rather that the tortuosity of the path depends upon the average saturation to the conducting fluid as well as upon the characteristics of the rock. itself. Inasmuch as the flow of fluid and the flow of electric current in many respects are analogous, it may be indicated further that the length of path for fluid also may not be independent of saturation. The following relationship can be derived to express the resistance to flow of electric current through a core sample partially saturated with conductive wetting phase, the non-wetting phase being non-conductive: where L is the average length of path followed by the current in flowing through a length L of partially saturated core, where L is the length of current path when the core is fully saturated, and where Rs and R, are the specific resistivities of the partially saturated and saturated core sample, respectively. It will be noted that R., the specific resistivity of the core sample when S, = 1.0, is equal to the "formation resistivity factor"&apos; multiplied by the specific resistivity of the saturating fluid. If it be assumed that the average lengths of path for fluid flow and for the flow of electric current are the same, then equation (5) may be combined with equations (l), (2) and (3) to give the following relationship: The above equation suggests including a correction for tortuosity when calculating the relative permeability of a reservoir rock to a wetting phase. The correction factor may be obtained from the resistivity-saturation relationship. For instance, the following calcu- lations are obtained for the unconsoli-dated sands described by Leverett Kw Kw Sw R°/Rs Pt/Pc¹ (Calc.) (Obs.) 0.30 0.08 0.88 0.02 0.0 0.40 0.16 0.94 0.06 0.04 0.50 0.27 0.97 0.14 0.11 0.60 0.40 0.98 0.26 0.21 0.70 0.53 0.98 0.39 0.35 0.80 0.68 0.99 0.57 0.54 0.90 0.84 0.99 0.77 0.76 1.00 1.00 1.00 1.00 1.00 It will be noted that the agreement between the calculated points and the observed data is rather good. Further investigation of the above method for obtaining relative permeabilities may be merited. For many sands within specified ranges of saturations the following relationship has been found to hold approximately&apos;: — =SW"......(7) Rs The exponent n in the above equation has been found to equal two for many sands so that equation (6) reduces to the following: The writer acknowledges the permission of The Texas Co. to submit this note for publication. 1. Walter Rose and W. A. Bruce—Jnl. of Pet. Tech., Vol. 1, No. 5, p. 127 (1949). 2. Walter Rose—Jnl. of Petr. Tech., Vol. 1, No. 5, p. 111 (1949). 3. G. E. Archie— -Trans. AIME, 146, 54 (1942). 4. M. C. Leverett— Trans. AIME, 142, 152 (1941). 5. M. C. Leverett—Trans. AIME, 132, 149 (1939).

Jan 1, 1949

By Owen Thornton

Recently equations have been presented by Rose and Bruce&apos; and by Rose², showing how the relative permeability of a reservoir rock may be determined from the capillary character of the rock. In particular, equations were developed to show the relationship between capillary pressure and the effective permeability to the wetting phase in a poly-phase flow system. The equations are as follows (nomenclature the same as in the Rose and Bruce paper) Rose and Bruce assume that the average length of path (L,), which the wetting fluid follows in flowing through a porous media is independent of the saturation to the wetting phase, so that 1 is a constant dependent only on the k rock, and the permeability to the wetting phase is a function of the saturation and of the capillnry pressure: In measuring the flow of ekctric current through partially saturated core samples, it has been observed that the electrical resistance usually is not a simple linear function of saturation. This fact indicates that the average length of path in the flow of electric current is not independent of saturation, but rather that the tortuosity of the path depends upon the average saturation to the conducting fluid as well as upon the characteristics of the rock. itself. Inasmuch as the flow of fluid and the flow of electric current in many respects are analogous, it may be indicated further that the length of path for fluid also may not be independent of saturation. The following relationship can be derived to express the resistance to flow of electric current through a core sample partially saturated with conductive wetting phase, the non-wetting phase being non-conductive: where L is the average length of path followed by the current in flowing through a length L of partially saturated core, where L is the length of current path when the core is fully saturated, and where Rs and R, are the specific resistivities of the partially saturated and saturated core sample, respectively. It will be noted that R., the specific resistivity of the core sample when S, = 1.0, is equal to the "formation resistivity factor"&apos; multiplied by the specific resistivity of the saturating fluid. If it be assumed that the average lengths of path for fluid flow and for the flow of electric current are the same, then equation (5) may be combined with equations (l), (2) and (3) to give the following relationship: The above equation suggests including a correction for tortuosity when calculating the relative permeability of a reservoir rock to a wetting phase. The correction factor may be obtained from the resistivity-saturation relationship. For instance, the following calcu- lations are obtained for the unconsoli-dated sands described by Leverett Kw Kw Sw R°/Rs Pt/Pc¹ (Calc.) (Obs.) 0.30 0.08 0.88 0.02 0.0 0.40 0.16 0.94 0.06 0.04 0.50 0.27 0.97 0.14 0.11 0.60 0.40 0.98 0.26 0.21 0.70 0.53 0.98 0.39 0.35 0.80 0.68 0.99 0.57 0.54 0.90 0.84 0.99 0.77 0.76 1.00 1.00 1.00 1.00 1.00 It will be noted that the agreement between the calculated points and the observed data is rather good. Further investigation of the above method for obtaining relative permeabilities may be merited. For many sands within specified ranges of saturations the following relationship has been found to hold approximately&apos;: — =SW"......(7) Rs The exponent n in the above equation has been found to equal two for many sands so that equation (6) reduces to the following: The writer acknowledges the permission of The Texas Co. to submit this note for publication. 1. Walter Rose and W. A. Bruce—Jnl. of Pet. Tech., Vol. 1, No. 5, p. 127 (1949). 2. Walter Rose—Jnl. of Petr. Tech., Vol. 1, No. 5, p. 111 (1949). 3. G. E. Archie— -Trans. AIME, 146, 54 (1942). 4. M. C. Leverett— Trans. AIME, 142, 152 (1941). 5. M. C. Leverett—Trans. AIME, 132, 149 (1939).

Jan 1, 1949

By Roscoe C. Clark

In October 1945. R. F. Farris. in an AIME paper entitled Method For Drtermining Minimum Waiting OIL Cenzent Time, presented a method for caiculating the minimum WOC* time required in oil well cementing operations. Briefly. this method consisted of shutting in a well. after the cement had been placed and noting the time required fur the wellhead pressure to reach a. maximum. This time was then multiplied by a factor of 1.5 to determine when the cement had reached sufficient strength to support the weight of the casing. As a result of this work, a number of areas have reduced their WOC time ~Wuirements with the subsequent saving of considerable rig time. The tests conducted by Farris were, for the most part, conducted under cementing temperatures in excess of 70°F. This was done because in the overwhelming majority of cases. cementing temperatures are in excess of 70°F (only in tile northern part of the country. primarily in the Rocky Mountain ares. in cementing surface casing are temperatures below 70° F. encountered, and such temperatures occur only during the winter months). The Stano-lind Research Laboratory since that time has performed a number of tests both in the laboratory and in the field to evaluate this WOC factor when cemeriting temperatures are lower than 70°F. The results of these tests indicated the need for greater WOC time in areas affeaed by abnormally low cementing temperatures. These tests indi.cated that a woc factor of 2 (Time from start to mix cement to maximum wellhead pressure x 2 = Time to drill plug) will allow sufficient time for the cement to develop adequate strength. A field test under abnormally low cementing temperatures (surface temyerature 35°F., mud discharge temperature <70°F. and cementing depth 500 ft.) in the Rangely Field, "* using the WOC factor of 2, indicated the time to drill the plug as 45 hours. Well conditions preventing getting back into the well until a 48-hour WOC time had elapsed. At this time, the plug drilled firm to hard indicating that the cement had reached its final set. It is contemplated that during next winter additional field tests will be performed to further check the results of the laboratory and field tests conducted to date,

Jan 1, 1949

By Roscoe C. Clark

In October 1945. R. F. Farris. in an AIME paper entitled Method For Drtermining Minimum Waiting OIL Cenzent Time, presented a method for caiculating the minimum WOC* time required in oil well cementing operations. Briefly. this method consisted of shutting in a well. after the cement had been placed and noting the time required fur the wellhead pressure to reach a. maximum. This time was then multiplied by a factor of 1.5 to determine when the cement had reached sufficient strength to support the weight of the casing. As a result of this work, a number of areas have reduced their WOC time ~Wuirements with the subsequent saving of considerable rig time. The tests conducted by Farris were, for the most part, conducted under cementing temperatures in excess of 70°F. This was done because in the overwhelming majority of cases. cementing temperatures are in excess of 70°F (only in tile northern part of the country. primarily in the Rocky Mountain ares. in cementing surface casing are temperatures below 70° F. encountered, and such temperatures occur only during the winter months). The Stano-lind Research Laboratory since that time has performed a number of tests both in the laboratory and in the field to evaluate this WOC factor when cemeriting temperatures are lower than 70°F. The results of these tests indicated the need for greater WOC time in areas affeaed by abnormally low cementing temperatures. These tests indi.cated that a woc factor of 2 (Time from start to mix cement to maximum wellhead pressure x 2 = Time to drill plug) will allow sufficient time for the cement to develop adequate strength. A field test under abnormally low cementing temperatures (surface temyerature 35°F., mud discharge temperature <70°F. and cementing depth 500 ft.) in the Rangely Field, "* using the WOC factor of 2, indicated the time to drill the plug as 45 hours. Well conditions preventing getting back into the well until a 48-hour WOC time had elapsed. At this time, the plug drilled firm to hard indicating that the cement had reached its final set. It is contemplated that during next winter additional field tests will be performed to further check the results of the laboratory and field tests conducted to date,

Jan 1, 1949

By J. E. Burke

THE origin of recrystallization textures continues to be a matter of controversy. One explanation is that a recrystallization texture occurs because only grains having a limited range of orientations ever appear in the deformed matrix—the oriented nuclea-tion* hypothesis. Another explanation is that grains essentially having all orientations are nucleated but that those having certain orientations grow much more rapidly than any others in the deformation texture, and thus only the rapidly growing grains survive when recrystallization is complete. There has recently appeared a great deal of evidence&apos;- indicate that recrystallized grains of face-centered cubic metals are frequently related to their parent grains by rotations of 20" to 40" about a common [lll] direction. Furthermore, it has been observed that the growth rate of the new grains depends upon their orientations with respect to the matrix, and that the most rapidly growing grains lie within the stated range of orientations. In a recent note, Beck7 has concluded from observations of this type that oriented growth alone is responsible for the appearance of preferred orientations in re-crystallized metals. It should be pointed out. however, that many of the available data indicate that oriented nucleation operates in addition to oriented growth. Thus, while oriented growth may permit a selection to be made among nuclei of several orientations, only a limited number of orientations are available in the first place for such selection.

Jan 1, 1953

By Paul A. Beck

THE occurrence of the (100) [lOO] or "cube" texture upon annealing of cold-rolled copper has been much investigated.&apos; The conditions favorable for its formation were found to be a high final annealing temperaturez or long annealing time," a high reduction of area in cold rolling prior to the final anneal,&apos; and a small penultimate grain size." The effects of penultimate grain size and of rolling reduction were found by Cook and Richards4 to be interrelated in such a way that any combination of them giving lower than a certain value of the final average thickness of the grains in the rolled material leads to a fairly complete cube texture with a given final annealing time and temperature. Also, according to the same authors, at a higher final annealing temperature a larger average rolled grain thickness, i.e., a lower final rolling reduction, is sufficient than at a lower temperature. These somewhat involved conditions can be understood readily on the basis of recent results obtained at this laboratory. Hsun Hu was able to show recently by means of quantitative pole figure determinations that the rolling texture of tough pitch copper, which is almost identical with that of 2s aluminum: may be described roughly as a scatter around four symmetrical "ideal" orientations not very far from (123) [112]. In the case of aluminum, annealing leads to retain-ment of the rolling texture with some decrease of the scatter around the four "ideal" orientations, and to the appearance of a new texture component, namely the cube texture." A microscopic technique, revealing grain orientations by means of oxide film and polarized light, showed that the retainment of the rolling texture is achieved through two different mechanisms operating simultaneously, namely "re-crystallization in situ," and the formation of strain-free grains in orientations different from their local surroundings, but identical with that of another component of the rolling texture. Thus, a local area in the rolled material, having approximately the orientation of one of the four "ideal" components of the texture, partly retains its orientation during annealing, while recovering from its cold-worked condition, and it is partially absorbed at the same time by invading strain-free grains of an orientation approximately corresponding to that of another "ideal" texture component. The reorientation here, as well as in the formation of the strain-free grains of "cube" orientation, may be described as a [Ill] rotation of about 40°, see Fig. 1 of ref. 6. The preferential growth of grains in such orientations is a result of the high mobility of grain boundaries corresponding to this relative orientation.&apos; " It appears very likely that in copper the mechanism of the structural changes during annealing is similar to that observed in aluminum (except for the much greater frequency of formation of annealing twins in copper). In both metals the new grains of cube orientation have a great advantage over the new grains with orientations close to one of the four components of the rolling texture. This advantage stems from their symmetrical orientation with respect to all four retained rolling texture components of the matrix; they are oriented favorably for growth at the expense of all of these four orientations. As a result, the growth of the "cube grains" is favored over the growth of the others, as soon as the new grains have grown large enough to be in contact with portions of the matrix containing elements of more than one, and preferably of all four component textures. It is clear that this critical size is smaller and, therefore, attained earlier in the annealing process if the structural units, such as grains and kink bands, representing the four matrix orientations are smaller, i. e., if the average thickness of the rolled grains is smaller. Hence, for a given annealing time and temperature, a smaller penultimate grain size and a higher rolling reduction both tend to increase that fraction of the annealing period during which the above condition is satisfied. Consequently, the percentage volume of material assuming the cube orientation increases. The same is true also for increasing time and temperature of annealing when the penultimate grain size and the final rolling reduction are constant, since the average size attained by the new grains during annealing increases with the annealing time and temperature. For the same reason, at higher annealing temperatures a given volume percentage of cube texture can be obtained with larger rolled grain thickness (larger penultimate grain size, or smaller rolling reduction) than at lower annealing temperatures. The well-known conspicuous sharpness of the cube texture may be interpreted as a result of the fact that selective growth of only those grains is favored that have an orientation closely symmetrical with respect to all four components of the deformation texture and exhibit, therefore, a high boundary mobility in contact with each. The effect of alloying elements in suppressing the cube texture, as described by Dahl and Pawlek,&apos; appears to be associated with a change in the rolling texture. For face-centered cubic metals, such as copper, which do exhibit the cube texture upon annealing, the rolling texture is always of the type described above, i. e., scattered around four "ideal orientations" of approximately (123) [112]. The addition of certain alloying elements, such as about 5 pct Zn or 0.05 pct P in copper, has the as yet unexplained effect of changing the rolling texture into the (110) 11121 type. This texture consists of two fairly sharply developed, twin related components. In such cases, as in 70-30 brass and in silver, the annealing texture again is related to the rolling texture by a [lll] rotation of about 30°, however, because of the different rolling texture to start from, it has no cube texture component. At higher temperatures, both in brassm and in silver," grain growth leads to a further change in texture: A [lll] rotation of the same amount, but in reversed direction, back to the original rolling texture.

Jan 1, 1952

By B. L. Averbach, M. Cohen, G. P. Conard

IT has been frequently observed that, when metal crystals are bent and annealed or when they are bent at elevated temperatures, the asterism of the Laue spots is split discontinuously into tiny intensity maxima. This finding indicates that segmented crystallites or subgrains are produced, which are relatively undistorted within themselves but which differ slightly in orientation from their neighbors. The following viewpoints have been put forward concerning the nature of this segmentation process: 1—Crussard&apos; has described the phenomenon as "re-crystallization in situ." According to this mechanism, the deformed lattice recrystallizes on heating into an aggregate of comparatively strain-free subgrains separated from one another by low-angle boundaries and having nearly the same orientation as the original crystal. This process differs from the classical type of recrystallization in that the latter involves the formation of grains having quite different orientations from that of the mother crystal. 2—A similar but more detailed picture has been advanced by Cahn&apos; who adopted the term "polygonization." In this interpretation, the plastic bending of lattice planes results in an excess of dislocations of one sign, but at suitable temperatures these dislocations migrate along slip planes and collect in localized regions to form an array of low-angle boundaries. Concurrently, the lattice segments between the boundaries lose their curvature and elastic strain. 3—The "cell formation" concept of Wood and co-workers: unlike the two hypotheses cited, postulates that the segmentation of the lattice is basically a mode of deformation and is not an annealing phenomenon. Cell formation appears to compete more effectively with respect to the normal slip process as the deformation temperature is increased and as the strain rate is decreased. The present work was performed on 3.2 mm diameter 99.99&apos; pct Zn single crystals, grown from the melt in a gradient furnace. The major impurity was 0.003 pct Fe. The crystal orientations ranged from those with basal plane parallel to the rod axis to those with the basal plane almost perpendicular to the rod axis. The specimens were bent on templates to effective radii varying from 14.2 to 1.3 cm at the temperatures from —196" to 100°C. In each case, the axis of bending was parallel to the basal plane. Subsequent annealing was carried out at temperatures from —196" to 400°C. Back-reflection Laue pictures were taken on the convex surface of the bent specimens, before and after annealing. This procedure was found to yield better resolution of the detail in the diffraction spots than did the previously used Laue transmission technique. Some X-ray pictures of rods bent at —196" and —78°C were taken at these respective temperatures without intermediate warming to room temperature. In addition, bent crystals were acid cut" parallel to the basal plane, and double-crystal spectrometer rocking-curves were obtained from the etched (0001) face before and after increment an-

Jan 1, 1954

By F. E. Steigert, A. H. Geisler

THE permanent magnet alloy comol, which contains 17 pct Mo, 12 pct Co, balance Fe, exhibits a precipitation reaction analogous to that at the iron end of the binary Fe-Mo system. The equilibrium precipitate, (P,), has a structure isomorphous with Fe,Mo, which is rhombohedra1 with parameters a = 8.97A and a = 3038.6&apos; according to the work of Arnfelt and Westgren.&apos; In the ternary alloy the parameters are a = 8.87A and a = 31°0.5&apos;. Oscillating crystal patterns of a single matrix crystal, M, in which P, was precipitated by slow cooling from 1300°C, showed that the orientation relationship of the two lattices is as follows: (110)P3 // (110)* (111)p3 // (110)m There are crystallites of P, in 12 different orientations in a single crystal of the parent solid solution. Microscopic examination shows that the crystallites are generally plate-like with their lateral dimensions parallel to (110) matrix planes. When precipitation in a supersaturated alloy quenched from 1300°C progressed isothermally at temperatures between 600" to 800°C, the evolution of the P, structure could be traced. Diffuse diffraction effects in Laue patterns provided early evidence of the precipitation process. Analyses of these by a previously described technique2 showed that they corresponded to rod-like elements parallel to <110> matrix directions in reciprocal space. With further aging to promote growth of the precipitate, the rod-like elements contracted to points in reciprocal space for normal Bragg reflection from the precipitate as shown by the left diagram in Fig. 1. Thus the diffuse scattering was attributed to the small thickness of the plate-like particles which was inadequate for sharp diffraction. When the precipitate particles were first thick enough to give normal diffraction their structure was different from that of the equilibrium precipitate, P,. The first structure, P1, presumably is a coherent transition struc-

Jan 1, 1952

By C. Goldberg, R. H. Wynne

WHEN using an optical goniometer to determine crystal orientation&apos; it is advantageous to use a preferential etchant so that the etch pits have plane faces which are parallel to crystallographic planes, all of which are of the same "form." "Westinghouse Silver Etch" (WAg), a preferential etch for germanium, is made up as follows: 40 ml of 49.7 pct hydrofluoric acid, 20 ml of 70.7 pct nitric acid, and 40 ml of distilled water containing 2.0 g of silver nitrate. Examination of metallographs of WAg etched surfaces (Fig. 1, for example) indicates that, regardless of crystal orientation, the faces of the etch pits are (111) surfaces. Optical goniometer examination of these WAg etched surfaces also indicates that the faces of the etch pits are (111) surfaces, i.e., all bright reflections are from (111) planes. When using an optical goniometer of the type described by Barrett,&apos; not only (111) reflections from a WAg etched germanium surface but also other reflections of lower intensity will be observed. These latter reflections can cause confusion. We have used an optical goniometer made from a war surplus astrocompass and a galvanometer lamp. The reflections are observed by using the goniometer in a darkened room and letting the reflected light be in- cident upon a piece of white paper. The resulting decrease of goniometer sensitivity enables (111) reflections only to be observed. This in turn permits the crystal orientation to be determined in a matter of minutes, since only two measurements are necessary. The authors wish to acknowledge the help received from R. E. Davis who assisted in making the metallographs and aided the authors in the interpretation of the metallographs.

Jan 1, 1954

By C. G. Dunn

THE present note, which was given in the form of a Research in Progress item,&apos; traces the origin of secondary recrystallization grains produced on annealing a cold rolled bicrystal specimen. The investigation began with the realization that a recently acquired conception for the origin of secondary grains produced on annealing cold rolled single-crystal specimens might require modifications for the case of polycrystalline materials. The stated conception2,3 begins with several conditions to be met by primary recrystallization: 1—a primary re-crystallization structure to consist of many small primaries and relatively few large primaries (diam- eters two or three times the average); 2—a primary recrystallization texture to consist of one strong preferred orientation or component and one or more weak components; and 3—a primary recrystalliza-tion structure-texture combination with some of the large primaries belonging to the weak components of the texture. When these conditions occur, some of the large primaries from the weak components of the texture

Jan 1, 1955

By F. G. Stone

A strain anneal process has been developed for the production of iron tensile test specimens, the gauge length consisting substantially of a single crystal. Since the method has been quite successful and the results of general interest, the process will be described in detail. The essential feature of the method is the continuous, slow increase of furnace temperature during the grain growth annealing treatment. Briefly, the procedure is as follows: I. Heat machined bars to 950°C in vacuum, hold I hr, furnace cool. 2. Strain to 3.5-3.8 pct elongation (axial loading). 3. Anneal, continuously raising furnace temperature from 450 to goo°C at a rate of so0 per day. 4. Hold at 900°C for 100 hr, furnace cool. Tensile test bars with a 1/4- X I-in. gauge section have been machined from 35 in. Armco iron plate and from 3/8 in. rounds of Puron, a high purity laboratory iron. The axes of the test bars were parallel to the rolling direction. During the machining operation the bars were polished in the lathe with No. 600 emery paper, and this polished surface proved satisfactory for subsequent macrographic examination. A micrographic examination of the materials showed that both were high in FeO inclusions, those of the Puron being smaller but much more numerous. An initial vacuum anneal of I hr at 950°C followed by furnace cooling resulted in a ferritic grain size of ASTM No. 3 for Armco and No. I for Puron. Special heat treatments which reversed these initial grain sizes produced no marked improvement in single crystal production after subsequent treatments. The strain for subsequent grain growth was determined by measuring the decrease in diameter of the tensile bar during elongation. The change in diameter could be measured with a micrometer to +0.0001 in., corresponding to an accuracy of 0.08 pct for the elongation. The accuracy of the diameter measurement is also dependent on grain size because of surface roughening during elongation, and for this reason, a No. 3 grain size is preferable. Optimum grain growth was obtained for strains between 3.5 and 3.8 pct elongation. Once this critical range had been cstablished, all tests were held within it, and thus only meager data were obtained on grain growth following strains outside this range. In general, grain size decreased with increasing strain to about 5.5 pct elongation. Grain growth was occasionally ohserved with less than 3.5 pct elongation although this may have been the result of error in measurement. The program control device for the grain growth anneal consisted of a I rpm motor and worm gear drive, operating the dial shaft of a pyrometer controller through a pulley. Dial speeds of 33 and 50°C per day were tried, but the results at the slower speed were not sufficiently better to warrant the increased furnace time. The furnace tube was evacuated at intervals during the run and kept sealed the remainder of the time. When the controller reached 900°C, it was stopped and the temperature held for 100 hr. This eliminated most of the numerous minute crystallites of about 0.5 mm dimension usually visible on the etched surface of the single crystal. Since recrystallization occurs at the A3 point, the top temperature of 900°C provided a 10"

Jan 1, 1949

By L. D. Jaffe, R. K. Pitler

IT would clearly be advantageous to produce molten titanium, suitable for alloying and casting, directly from the relatively inexpensive tetra-chloride, without using a metallic reducing agent. Accordingly, a preliminary investigation has been made of the production of titanium by hydrogen reduction of the tetrachloride in an electric arc furnace. For the reaction: TiCl4(g) + 2H2(g) ? Ti(s) + 4HCl(g), Lockhart and his colleagues&apos; have calculated equilibrium constants at 800" to 1500°K, based on tables of Brewer.&apos; Extrapolating these data on the assumption that the heat of reaction varies linearly with temperature, and using Brewer&apos;s value for the heat of fusion, there is obtained for the reaction: TiCl4(g) + 2H2(g) ? Ti(l) + 4HCl(g) an equilibrium constant at 2100°K (100" above the melting point) Kp = (PHCl)4/pTlcl4 (Ph2)2 = 0.167 atm. If this is correct, starting with hydrogen saturated with TiC14 at 25°C, where the vapor pressure of the latter3 is 12.6 mm, and maintaining the overall pressure at 1 atm, 99 1/4 pct of the TiC14 would be reduced to Ti at equilibrium. An arc furnace designed for the melting of titanium and lined with water-cooled copper was used for the preliminary experimental check. Its inside diameter was 2 7/16 in. and height 6 in. The water-cooled electrode was tipped with 3/4 in. diam tung-sten. In the one run carried out, the furnace was charged with a starting batch of 293.35 g of scrap titanium,&apos; analyzing 99.24 pct Ti. After the system was twice pumped out and flushed with argon to remove air, the arc was struck in argon and kept at 400 amp dc, electrode negative, for 1 min to melt the starting batch. Commercial tank hydrogen, dried by passing over silica gel and bubbled through technical grade TiC14 at room temperature, was then admitted to the furnace. The inlet tube directed this gas downward toward the arc and melt; the gas outlet was at the top of the furnace. The quantity of gas passed through was not measured accurately but is estimated to be about 50 liters per min at a few mm of mercury above atmospheric pressure. The arc was held in the H2-TiC14 mixture at 400 amp with little difficulty. After 10 min the arc burned through the copper lining above the melt, admitting water and ending the run. (This had happened frequently in straight melting runs under argon, and is not thought due to the atmosphere used.) In the furnace were found an ingot, several small pieces, and a little metallic powder, evidently formed when water entered the hot furnace. Some titanium also clung to the electrode. The portions were weighed and separately analyzed for titanium. Their total weight was 321.76 g of 94.82 pct overall purity. Much of the impurity consisted of tungsten broken off when the titanium was removed from the electrode. No detailed impurity analysis was made because the starting materials were impure and flooding the furnace introduced further contamination. Thus, the metal recovered contained 305.08 g Ti, as compared to 291.12 g in the starting batch. Titanium could not have been carried over from previous melting runs in the furnace, as the interior was sandblasted and the electrode ground clean before the run. Evidently at least 13.96 g of Ti were produced from TiCl4. Since this would require complete reduction of 430 liters of TiCl, gas at 12.6 mm of Hg, the efficiency of the process must have been rather high. Experimental work is continuing. No reason is seen why the process could not be scaled up to the size of a 30-ton steel-melting arc furnace. In a large unit there would be a large molten pool from which liquid metal could be withdrawn for alloying and casting. The problems of electrodes and power supply are similar to those arising in arc furnaces for melting titanium. Unreacted TiC14 and the HC1 in the exhaust gases could be recovered; unreacted H2 could be dried and re-used. The melt would be saturated with hydrogen, whose solubility in liquid titanium is unknown. Small amounts of hydrogen seem to have little effect on the properties of titanium.5 If the amount introduced was so large as to impair properties or cause casting difficulties, it could be reduced by holding the melt under an inert gas or by pumping on it, prior to casting. Acknowledgment The authors would like to thank I. Preble and M. Goldman for their valuable aid in the experimental work and the thermodynamic calculations, respectively. References 1R. J. Lockhart, J. J. Ward, M. J. Hussey, and J. W. Clegg: In unpublished report, "U. S. Air Force Project Rand. Titanium and Titanium Base Alloys." Battelle Memorial Institute (1949) 37-44. 2 L. Brewer et al: Chemistry and Metallurgy of Miscellaneous Materials—Thermodynamics. Ed. by L. L. Quill. pp 13-39, 60-192. (1950). McGraw-Hill Book Co. 3 K. Arii: Scientific Reports. Tohoku Imp. Univ. (1933) 22, 182. 4 R. S. Dean, J. R. Long, F. S. Wartman, and E. L. Anderson: Transactions AIME (1946) 166, 369-381; Metals Technology (Feb. 1946) TP 1961E. * R. I. Jaffee and I. E. Campbell: Transactions AIME (1949) 185, 646-654; Journal of Metals (Sept. 1949) TP 26813.

Jan 1, 1951

By Mary Barrett, Walter Rose

INTRODUCTION The conventional way to program reservoir problems* for solution on the electric analyzer1 is one which concentrates the block units towards the inner radius of the prototype system being represented by the analog model. This is achieved by the device of considering block units of equal value radial resistance, leading to the consequences: (1) the ratio of the external to the internal radius of each block unit is a constant (i.e. r1/ri-l = constant a); (2) the external radius of the nth block unit is equal to the innermost radius of the system times the constant a raised to the nth power: (3) the capacitance of the block units increase by a factor of a2 going out radially from the innermost to the outermost boundaries of the system; (4) given n block units in the radial direction, the capacitance ratio of the outermost to the innermost block unit is a (2n-2); and (5) the vertical resistance of the block units decrease by a factor of a going out radially from the innermost to the outermost boundaries of the system, such that the ratio of the maximum to minimum vertical resistance is also given by the factor a(2n-2) PRESENT PROGRAMMING METHOD While this conventional way of programming problems is quite adequate for routine uses of the electric analyzer, it leads to difficulties in those cases where the inner radius of the prototype system (e.g., the well-bore) is small compared to the external radius (e.g.. the external reservoir boundary). To handle such a case by the conventional method would require either that a large value be selected for the constant a or that a large number n, of radial block units be chosen. In consequence, the capacitance and vertical resistance ratios become impossibly large, as will be evident from the relations given above. In any event, the size of the smallest and largest capacitors will always be limited by the size of commercially available components, and the analyzer itself will determine how many mesh points are available for radial block units. For example, it can be shown that if the maximum capacitance ratio which can be electrically handled is a factor of l04, the maximum external radius of the system which can be considered (assuming an internal wellbore radius of 0.25 ft is: It is thus seen that in direct consequence of having the inner wellbore radius small compared to the external radius, models extending beyond 30 to 40 ft are not possible when the capacitance ratio is limited to l04. (NB. A value of 10-9 farads can perhaps be taken as the minimum electrical capacitance possible if corrections for the capacitance of the lead wires are to be avoided. Values greater than 10-5 farads would require the use of unstable and inaccurate electrolytic capacitors). On the other hand, models extending out to 500 to 5,000 ft may be desired in single-well problems, and hence the need for a revised method of problem programming. * REVISED PROGRAMMING METHOD The revised method of programming is one which attempts to retain the desirable features of the conventional method (viz. concentration of block units towards the inner boundary, simplicity in computation, etc.) without having as a consequence that impossible capacitance and vertical resistance ratios will be required. Other advantages will also be achieved by the revised

Jan 1, 1957