Search Documents

By C. Chamberlain

The Telfer Project, Australia's newest, largest, and most remote gold mine treats 480 kt of ore grading 9.33 g/t derived from open pit mining operations. Coarse gold is recovered by gravity concentration with jigs and further upgraded wing a continuous strake launder table, and by amalgamation. Remaining gold is recovered in a cyanide circuit and incorporates flat bottom air agitators, counter current decantation (CCD) and stellar filters for clarification and precipitate removal. Overall recovery into a bullion averages 98%. The mill incorporates a number of design features that allow for maximum efficiency and security wing a minimum number of operation personnel.

Jan 1, 1983

By D R. Seaman, B Adamson, F Burns, B A. Seaman, P Manton

The Telfer concentrator, located in the Great Sandy Desert of Western Australia, consists of a dual train gold/copper operation processing ore from one underground and, currently, two open pit mines with differing mineralogy. The flotation circuit of each train was designed to operate in several modes depending on the feed mineralogy. The majority of ore mined at Telfer is processed in a sequential mode where copper minerals are first floated into a saleable copper concentrate followed by the flotation of an auriferous pyrite concentrate which is treated in an on-site hydrometallurgical plant (carbon-in-leach (CIL)). Gold is recovered as a gravity product within the primary grinding circuit, to the copper concentrate, and to a lesser extent, the CIL circuit.Since Telfer was re-opened, with a new concentrator, in 2004, the processing plant has struggled with poor copper concentrate grades, partially due to the excessive entrainment of non-sulfide gangue minerals in the copper flotation circuit and, more recently, due to composite copper particles produced when processing ore from a supplementary satellite pit that has not previously been processed through the new Telfer concentrator. Gold recoveries in the CIL circuit have also been below industry standard. This paper presents the implementation of recent changes made to the circuit to address these performance issues. The reconfiguration of the circuit has involved the installation of the following major equipment items: two ISAMillsÖ in ultra-fine grinding applications (one in the copper circuit and one in the pyrite circuit), two Jameson Cells to improve fine gangue rejection and a bank of 5 + Outotec TC30s to recovery copper and gold from the reground pyrite stream. The equipment was purchased direct from vendors and an engineering firm contracted to design and install the multi-vendor reconfiguration upgrade.CITATION:Seaman, D R, Burns, F, Adamson, B, Seaman, B A and Manton, P, 2012. Telfer processing plant upgrade - The implementation of additional cleaning capacity and the regrinding of copper and pyrite concentrates, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 373-382 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By R Dunne, G Lane, S Ha, D Dreisinger

The paper outlines the 17 Mt/a Telfer Project plant process design from sample selection to feasibility study design. The 366 Mt Telfer mine reserve consists of a diverse range of copper and gold mineralisation, from massive sulfide reef ores to stockwork ore, oxide copper minerals to chalcopyrite, siltstone to competent quartzite, all with relatively high levels of gravity recoverable gold. The complexity of the orebody demanded a flexible plant that could recover copper and gold values by a combination of gravity recovery, flotation and concentrate leaching. The demands of treating ore from a high grade underground mine and a variable grade open pit (that includes underground old mine workings) necessitated a dual train approach from primary crushing to concentrate production in order to minimise the requirement for campaigning of different ore types. An extensive sampling, testwork and technical evaluation program was undertaken to identify processing characteristics and the optimum process route for each ore type. The design experience included: the development of robust primary stockpiling and pebble crushing concepts; detailed review of scale-up of SAG and ball mill pilot plant data to plant scale; the selection of two 15 MW SAG mills and two 13 MW ball mills for the grinding circuit; and detailed modelling of the pyrite concentrate carbon-in-leach (CIL)/sulfidisation acidification recovery thickening (SART)/acidification volatilisation recovery (AVR) process to optimise design for copper and cyanide recovery from leach liquors. The Telfer plant design also measures the development of process design based on experiences at the Cadia Hill Cu/Au concentrator, commissioned in 1998. The differences between the two plants are compared and contrasted.

Jan 1, 2003

Teller Underground Mine was established to extract ore from the Middle Vale Reef located on the eastern flank of Telfer Main Dome.The mine is located below a 150 m deep open pit operation. The ore body is shallow dipping highly structured, and is a main aquifer in quite difficult ground conditions.In respect of these conditions it was determined to access the orebody using an adaptation of coal mining and hard rock mining methods, with support being achieved using a combination of island pillars, rock bolts and timber stalls.The paper will describe these methods in more detail, then discuss the successes and failures of these methods when put into practice. As well, it will detail several factors whose influences were found to be greater than previously expected and stress the importance of good geotechnical advice.

Jan 1, 1993

By A. Flemming

"As the next century draws near, new mine properties must be brought into production to replace existing operations that are approaching their economic life. This paper presents some of the critical technical issues being addressed by Manalta Coal Ltd. as they strive to bring the Telkwa Coal Project near Smithers, BC into production during the year 2000. The mine is planned to produce between 1.0 to 1.5 million tonnes per year of medium volatile coal for export to overseas thermal and PCI markets. IntroductionManalta Coal Ltd. (Manalta) is proposing the development and operation of a surface coal mine and associated infrastructure approximately six kilometres southwest of the village of Telkwa, British Columbia (Fig. 1). The infrastructure consists of a coal washing facility, tailings disposal area, clean coal haul road, access road and rail loadout facility. Over a 25-year period, the mine is expected to produce between 25 and 37 million clean tonnes of coal primarily for the export market.To achieve public and governmental approval for the development, the project will be reviewed under British Columbia’s Environmental Assessment Act. Manalta entered the formal Assessment process in February 1, 1997 with the submission of an Application for a Project Approval Certificate for the Telkwa Coal Project."

Jan 1, 1997

By Elaine T. Cullen, Albert H. Fein

Federal law mandates that all miners receive safety and health training when first entering the mining industry and at least 8 hours annually thereafter. Although the mining industry has historically relied on an experiential master-apprentice model for training new employees, the formal safety training provided to miners is generally done in a classroom, with mixed results. In a series of stakeholder meetings held by NIOSH across the West in 1997-2000, trainers identified significant gaps in materials that were available to teach new and experienced miners. They asked whether NIOSH could develop effective materials to fill these perceived gaps, as well as make training more effective for those who were required to attend, but who often refused to be attentive. Adult learning theories, social learning theories, mentoring, and storytelling were all employed in the development of a series of safety training videos that have become very popular in the mining industry. This Report of Investigations describes the theoretical frameworks that were used, the process that was developed to produce the videos, and the results of the evaluations as to whether or not they were effective in training new and experienced miners.

Jan 8, 2005

By Noboru Masuko, Sachiko Ono

"The structure and composition of anodic films formed on aluminum in a borate solution have been investigated by using TEM and SIMS with respect to the effect of current density and electrolyte temperature. The film is composed of a boron-containing outer layer and a boron-free inner layer with disc-like crystals present at the interface. The thickness of the film formed at constant current density up to an identical voltage, decreases with increasing current density. The thickness increases remarkably with elevated temperature. The transport number of Al3+ estimated from the thickness ratio .of the cuter to the inner layers is 0.4 when the film is formed at the current density of 20 Am-2 at 60°C. It increases slightly with increasing current density and decreases significantly with increasing temperature. Content of boron in the outer layer increases 1.5 times when current density .increases 10 times. These changes in film structure and composition with electrolysis conditions must have a significant role in the determination of electric properties of anodic alumina films as a capacitor material.IntroductionThe growth of anodic alumina film in ·a neutral electrolyte proceeds at both film/electrolyte and film/substrate interfaces giving a duplex structure. The oxide layer formed at the former interface includes electrolyte anions while a-pure alumina layer is formed at the latter interface. The thickness ratios of each layer respectively represent transport numbers of Al3+ and 0 2 - (1). The film thickness and the incorporated anion content as well as transport numbers of both ions must affect the dielectric properties of the film as a capacitor material. However, the correlation between film structure and electrolytic conditions is not fully understood (2). For the further clarification of anodic film growth mechanism, more detailed characterization of anodic films in relation to electrolytic conditions is advantageous. In the present paper, therefore, the effect of current density and electrolyte temperature on the microstructure and composition of anodic barrier films formed in a neutral borate solution was studied. The films were characterized by direct observation using transmission electron microscopy (TEM) and depth profiles of constituent elements obtained by secondary ion mass spectroscopy (SIMS)."

Jan 1, 2000

By Leonard D. Jaffe, Donald C. Buffum

THE importance of temper brittleness in alloy steels has long been realized in Europe, In the United States recognition of its importance has developed within the last several years. Many brittle failures encountered in parts made of alloy steel are undoubtedly attributable, wholly or in part, to temper brittleness. These failures have occurred particularly at low temperatures, under shock loading, and in the presence of notches, restraints and combined stresses. It has been almost universally accepted that plain carbon steels are not susceptible to temper brittleness. As a result, considerable effort has been expended in attempts to discover the manner in which alloying elements introduce temper brittleness. It is desired to raise the possibility that plain carbon steels are not only susceptible to temper brittleness, but are much more susceptible than alloy steels, in the sense that they embrittle much more rapidly. It is suggested that previous views, (that plain carbon steels are not susceptible), are based upon an erroneous interpretation of the experimental results. INTERPRETATION OF PREVIOUS DATA For many years the standard criterion for susceptibility of a steel to temper brittleness consisted of comparison of the energy absorption, in a notched-bar impact test at room temperature, of specimens that had received two heat treatments.1 One specimen (or group of specimens) was quenched, tempered, and quenched from the temper. The other specimen (or group) differed only in having received an embrittlement treatment, which might consist of a slow cool from the tempering temperature, or of an isothermal hold in the range 450-550°C subsequent to quenching from the temper. If the energy absorption of the specimen receiving the embrittlement treatment was lower than that of the specimen not given this treatment, it was said that the steel was susceptible to temper brittleness, If the energy absorptions were the same, it was said that the steel was not susceptible. Several investigators2,3 found that plain carbon steels showed negligible difference in energy absorption in such tests (at least when their manganese content was below 0.60 pct), and concluded that plain carbon steels are not susceptible to temper brittleness. Recently the deficiencies of the criterion mentioned above have been pointed out.4-6 The criterion now generally used for susceptibility to temper brittleness retains the heat treatments used in the earlier scheme, but instead of the notched-bar impact tests being made only at room temperature, they are made over a range of temperatures, covering the transition from ductile to brittle fracture, If the transition temperature of the specimens receiving the embrittlement treatment is higher than those

Jan 1, 1948

By L. Callele, C. DiGiovanni, L. Li, R. Driver

"Hot-dip galvanizing is a common procedure used to protect structural steels from corrosive environments. However, in a construction project involving welded structural steel platforms by a Canadian steel structures company, numerous connections were found with large cracks in the welded corner joints and T-joints after galvanizing. Historically, in other similar projects by the same industry partner, cracking did not occur making this an unforeseen and new phenomenon. The project explored the mechanical properties of the base material, the thermal stresses induced by the hot-dip galvanizing, and the fracture surface of the cracks. A key feature to note, the fracture surface showed intergranular cracking with no plastic deformation. Lab testing showed the base material exhibited intergranular brittle behavior when heated and fractured at the galvanizing temperature. The transition to a brittle fracture mode is due to temper embrittlement and the segregation of elements in the grain boundaries.INTRODUCTION Galvanization is a common practice for protecting steel structures from the corrosive environment. Hot-dip galvanizing is the most common approach to bonding the zinc layer to the steel, and it is highly cost effective. In the case of welded structures, it is common to do the hot-dip galvanizing process after welding. This is so the protective layer can be applied to the structure as a whole and over the welds. In a recent construction project carried out in industry, a steel frame platform structure measuring approximately 3 m x 7 m was galvanized after welding fabrication. The structure was built of CSA G40.21 350W and CSA G40.20/G40.21 300W plain carbon steels and welded using a metal core arc welding process for the flanges and a flux core arc welding process for the webs of the beams. Due to their size, the platforms underwent a double-dip galvanizing process meaning half of the structures were submerged in the molten zinc path while the other half was exposed to the ambient air. This was repeated for the remaining side. Shortly after the galvanizing process was completed, numerous large cracks were found in the welded joints. Given there was no history of weld cracks after galvanizing in previous similar frames that were double dipped, this failure posed a new and curious problem."

Jan 1, 2017

By Joseph Ames

THERE are two distinct questions associated with the concept of temperature: one is practical, the other is theoretical. Our fundamental ideas of temperature come from our senses; we know what we mean by the words "hot" and "cold," or by saying one body is "hotter than another." But for scientific purposes words require definition. We are guided in this matter, as in all other scientific questions, by our knowledge of facts of observation. When two bodies at different temperatures are intimately associated, e.g., a hot stone is, dropped into a pail of water, our experience is that ultimately they come to the smile temperature as far as our senses can tell; the hot body becomes colder and the cold body hotter. In the case of a block of ice, immersed in, water, the ice melts, forming cold water, which then mixes with the other water, the final result being water colder than the original water. From our knowledge of the nature of heat phenomena, we learn that in this process one body loses, heat and the other gains heat, the condition of equilibrium being, one in which each body gains Is much heat as it loses. It is distinctly assumed in this statement that only two bodies are concerned in the transfer of heat, all other bodies being rendered in some way impervious to heat. The body that in the process loses heat is said to have the ?higher temperature" while the body that gains the heat is said to have the "lower temperature;" and, when thermal equilibrium is reached, the two bodies are said to have the "same temperature." Consequently, the temperature of a body may be defined, is it was by Maxwell, as "its thermal state considered with reference to its power of communicating heat to other bodies."

Jan 9, 1919

By Jack Parker

Cycles of mine convergence coincide with annual cycles of temperature and humidity in the mine. Laboratory measurements confirm that the presence of moisture reduces rock strength and induces internal rock stress. Findings are used in the design of mine openings.

Jan 1, 1969

By P. Bissert, M. Klein, L. Yan, D. Yantek

"Mine Safety and Health Administration (MSHA) regulations require underground coal mines to use refuge alternatives (RAs) to provide a breathable air environment for 96 hrs. One of the main concerns with the use of mobile RAs is the heat and humidity buildup inside an RA. The accumulation of heat and humidity can result in miners suffering heat stress or even death. MSHA regulations require that the apparent temperature in a fully occupied RA must not exceed 95°F. To investigate this issue, the National Institute for Occupational Safety and Health (NIOSH) conducted testing on a 23-person tent-type RA in its Experimental Mine (EM) in a test area that was isolated from the mine ventilation system. The test results showed that the average measured air temperature within the RA increased by 9.4°C (17°F) and the relative humidity (RH) approached 94 %RH. The test results were used to benchmark a thermal simulation model of the tested RA. The validated thermal simulation model predicted the average air temperature inside the RA at the end of 96 hours to within 0.6°C (1.0°F) of the average measured air temperature. INTRODUCTION If an accident occurs in an underground coal mine, miners who fail to escape from the mine can enter an RA for protection from adverse conditions, such as high carbon monoxide levels. One of the main concerns with the use of mobile RAs is the potentially adverse thermal environment inside an RA from the metabolic heat of the occupants and the heat released by the carbon dioxide (CO2) scrubbing system. Moreover, the humidity within the RA will increase through occupants’ respiration and perspiration and from the chemical reaction within the CO2 scrubbing system. The accumulation of heat and humidity can result in miners suffering heat stress, heat stroke, or even death. In its 2007 report to Congress, the National Institute for Occupational Safety and Health (NIOSH) Office of Mine Safety and Health Research (OMSHR) recommended that RAs should be designed to ensure that the internal apparent temperature (a temperature-humidity metric) in an occupied RA does not exceed 35°C (95°F). However, a standard method to determine compliance with this metric does not exist. The heat transfer process within and surrounding an RA is very complex, and is not easily defined analytically or experimentally. To investigate the related issues, OMSHR conducted heat and humidity testing on a 23-person tent-type RA in its Experimental Mine (EM) in a test area that was isolated from the mine ventilation system. During the testing, numerous parameters were measured: heat input to the chamber, the air temperature and relative humidity inside the RA, the air temperature in the mine, the mine strata temperatures versus depth, and the airflow inside and outside the chamber. The focus of this paper is on the temperature rise within an RA. TAITherm heat transfer analysis software was used to develop a thermal simulation model of the RA as it was tested in the mine, using the test results as the benchmark. Both sensible and latent heat were used in the test and the model."

Jan 1, 2016

By P. Bissert, L. Yan, D. Yantek

"Federal regulations require refuge alternatives (RAs) in underground coal mines to sustain life for 96 hours while maintaining an apparent temperature (AT) below 35°C (95°F). NIOSH research has shown that heat and humidity buildup is a major concern with RAs because they have a limited ability to dissipate heat, and high internal air temperature and relative humidity (RH) may expose occupants to heat stress. The heat transfer process within and surrounding an RA is very complex and is not easily defined analytically nor experimentally. To investigate heat and humidity buildup in RAs, NIOSH conducted multiple in-mine 96-hour tests on a 6-person metal-type RA, a 23-person tent-type RA, and a 10-person tent-type RA. The test results show that when moisture was introduced into the tests to represent perspiration and respiration from miners (wet tests), the average measured internal air temperature at midheight increased by 7.7°C, 9.4°C, and 10.5°C, and the RH approached 95%, 94%, and 88%, respectively. For the dry tests when no moisture was introduced, the average internal temperature increased by 8.4°C, 10.3°C, and 12.6°C, respectively. INTRODUCTION If an accident occurs in an underground coal mine, miners who cannot escape from the mine can enter an RA for protection from adverse conditions, such as high carbon monoxide levels. One of the main concerns with the use of mobile RAs is the thermal environment inside the RA. The metabolic heat of the occupants and the heat released by the CO2 scrubbing system will cause the interior air temperature to increase. Moreover, the humidity within the RA will increase through occupants’ respiration and perspiration and from the chemical reaction within the CO2 scrubbing system. The internal thermal conditions can subject miners to heat stress, which can lead to heat exhaustion, heat stroke, or even death depending on duration and magnitude of exposure. MSHA regulations require that RAs must be designed to ensure that the internal apparent temperature does not exceed 35°C (95°F) when the RA is fully occupied [1]. Apparent temperature (AT) is a temperature-humidity metric for the perceived temperature caused by the combined effects of air temperature, relative humidity (RH), and wind speed. It is used to assess the perception of indoor temperatures when workplaces are not sufficiently heated, cooled, or insulated to provide comfortable or healthy conditions. Before a mobile RA can be deployed at an underground mine for emergency usage, it must be tested to show that its internal AT when fully occupied will not exceed the 35°C (95°F) limit. For practical reasons, RA manufacturers usually conduct their tests at above-ground test facilities. To investigate RA thermal response in an in-mine environment, NIOSH conducted multiple 96-hour tests on a 6-person metal-type RA, a 23-person tent-type RA, and a 10-person tent-type RA in its underground coal mine facility. The work described in this paper could be used by RA manufacturers to determine a final temperature rise based solely on dry and time-reduced testing."

Jan 1, 2017

By T. Koulomzine

The theory of the Askania magnetometer, as well as a complete discussion of all factors influencing magnetometer readings, is very ably described by J. Wallace Joyce. We will assume that the reader is thoroughly familiar with this theory and we will use whenever possible the same notations for the physical values involved in the theory. On the other hand, we believe that the principal formulas of the magnetometer can be deduced much more easily by the use of differential calculus than by the methods employed by Joyce. Consequently, we are presenting herewith a resume of the theory of the vertical magnetometer in order to determine the correct formula of the temperature coefficient which we propose to compensate.

Jan 1, 1949

By Leonard Waldo

(New York Meeting, February, 1911.) THE recent and rapid development of the physics of engineering materials at temperatures as low as that of liquid air and as high is that of the electric are, has drawn renewed attention to the absence of tables, properly printed and spaced, for the convenient and accurate translation of temperature from centigrade to Fahrenheit scales and vice versa. It is to be noted that the Fahrenheit scale is the almost universal usage in foundries and shops in the United States, though the laboratories of the same works employ the centigrade notation. The growing use of the electric furnace in Germany and France calls for much American citation all in centigrade high temperatures, and while the arithmetical calculation is simple, it becomes burdensome when often repeated. I have been surprised at the numerous reprints of Table I. from centigrade to Fahrenheit degrees, first privately printed for personal use, which have been made by works, blue-prints, test-books, and technical journals, and I hope that Table II., from Fahrenheit to centigrade degrees, will be equally useful.

Jan 4, 1913

Discussion of the paper of Leonard Waldo, presented at the New York meeting, February, 1911, and printed in Bulletin No. 76, April, 1913, pp. 555 to 559. HERBERT HAAS, San Francisco, Cal. (communication to the Secretary*):-Referring to Leonard Waldo's paper on Temperature Conversion Tables, I believe the following formulas can be easily remembered, and by reference to the thermomter scales of Fahrenheit (F.), Celsius (C.), and Réaumur (R.), their derivation and relation are at once understood n° F. = 4/9 (n°-32) R. = (n°-32) C. n° C.=(9/5 n° + 32) F. = 4/5 n° R. n° R.=(9/4 n° + 32) F. = 5/4 n° C. As the freezing point of water is at 32° F., corresponding to 0° C. and 0° R., 32 must be deducted from the Fahrenheit degrees when these are converted into C. or R. degrees. Likewise, to C. or R. degrees converted into F. degrees 32 must be added. The fractions 4/9 and 5/9 and their reciprocals are obtained thus:

Jan 5, 1913

By S. K. Kawatra, M. T. Rusesky, T. C. Eisele, D. X. Zhang

It has been observed in some mineral processing plants that grinding circuit efficiency varies seasonally, such as in some plants which are located in the northern US and Canada and undergo large seasonal temperature changes, with the grinding circuit efficiency different between summer and winter. This indicates that the temperature of grinding circuit slurry has a noticeable effect on grinding performance. The effect has rarely been studied. To this end, an investigation to examine the effect of changing temperature on efficiency and determination of the mechanism responsible has been carried out. Plant investigations and laboratory experiments have been conducted in order to study hydrocyclones. It was demonstrated that when the pressure drop is held constant, the d50(c) size decreased approximately linearly with increasing temperature, while the shape of the reduced efficiency curve remained nearly constant. This effect was determined to be due to changes in slurry viscosity with temperature.

Jan 1, 1990

By A. D. Misener, L. G. D. Thompson

"IntroductionIt was shown by work previously reported that reliable geothermal gradients representative of various regions of the earth's, surface could he obtained from extended surveys of the rock temperatures in operating mines. These surveys showed the presence of anomalies in the isothermal levels and the existence of regions of regular behaviour. Below about 3,000 feet the temperature gradients became quite regular over the areas stud1ed. It is these regular gradients which are taken as representative of the region, wherever possible.The present paper describes the extension of this work which was undertaken to obtain further temperature gradients with a view to correlating them to other geophysical properties determined for the same regions. The additional data obtained have indicated possible reasons for the temperature anomalies. The experimental procedure was similar to that already described and was again made possible through the wholehearted co-operation of the management and the assistance of the personnel of the mines concerned. The research was entirely supported by a grant from the Research Council of Ontario.The equipment was a distinct improvement over that previously used and made it possible to take many more accurate temperature readings in a given time. Thermistor resistance thermometers were used, encased in silver sheaths and protected against damage by heavy copper casings. These were calibrated with a standard platinum resistance thermometer.The bridge used with these thermometers was one of a number designed and built by the Meteorological Service and designated M.S.C. Thermometer Indicator Type C-3. This very convenient and portable instrument operated from batteries in the instrument case. Multiple thermometer connections were provided so that rapid readings• of a number of thermometers was possible to accuracy of the order of 0.1°F. All electrical connections on the panel are covered with Dow-Corning ignition compound to prevent; electrical leakage due to moisture condensation. This, together with the high resistance of the thermometers and components of the bridge, gave much more reliable results than previously obtainable."

Jan 1, 1950

HENRY M. HOWE, Bedford Hills, N. Y. (communication to the Secretary *).-Dr. Burgess would add to the value of this important paper if he would give us the carbon content of the steel made in the several charges, or, if this cannot be done, if he would indicate whether, as might he inferred from his paper, the teeming temperature is approximately constant and independent of the carbon content of the steel, or whether as would be expected, it varies with the content and is materially higher for low- than for high-carbon steel. If he could add to Table 3 the time of the several tests, that would be welcome. His Table 3 leads one to infer that, once the bath is melted somewhat more than flat, the temperature of the roof is nearly constant and is approximately the highest compatible with reasonable longevity. That is to say, the metal is heated by means of a roof and flame at nearly constant temperature. The temperature of the observed upper surface of the slag should reflect that of the roof approximately, and in Table 3 this seems to be true, the temperature of both rising toward the middle of the record, and again falling. The slag as the medium through which the heat passes from roof to metal, should be intermediate in temperature between the two, as it is here. But the temperature of the metal ought to rise continuously, unless when cold additions are charged, and this too seems to be. true, allowing for slight observational errors, the total rise from the first to the last spoon-test being 89°. The temperature drop of from 85° to 135° from the last spoon-test to the teeming is surprisingly great, suggesting that the spoon-tests represent the metal immediately beneath the slag, and therefore appre-

Jan 6, 1917

By Xiang Sun

Microwave heating has been used in numerous industrial processes due to its great advantages when compared with conventional heating methods. However, microwave heated products can be affected by non-uniform temperature distribution resulting from the mechanisms of microwave heating. To overcome this problem, a critical step is to have a temperature-time profile. In order to characterize and evaluate microwave heating effects, an accurate temperature measurement is needed. This paper discusses the possibility of applying several temperature measurement techniques in microwave processing. Both contact and non-contact methods are introduced and compared.

Jan 1, 2006