Search Documents

By B G. Blacka, O Salisbury, K W. Mills, R G. Jeffrey

Whitehaven Coal Limited operates an underground longwall mine near Narrabri, New South Wales. The mining horizon in the Hoskissons Seam is overlain by a 16–20 m thick unit known as the Digby Conglomerate, a unit that is sufficiently massive to have potential to cause a windblast during first caving at the start of each longwall panel and periodic weighting throughout the panel. A program of hydraulic fracturing has been successfully used to precondition the conglomerate strata to increase its caveability at the start of each panel. This paper presents a system of temperature monitoring that was used successfully to measure hydraulic fractures at Whitehaven confirming their rate of growth, orientation and interaction with previously placed hydraulic fractures.CITATION:Mills, K W, Blacka, B G, Jeffrey, R G and Salisbury, O, 2014. Temperature monitoring of hydraulic fractures used for preconditioning massive conglomerate strata to reduce windblast, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 189–194 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By A. Cummings

This paper reports two aspects of reactivity of complex Ni-Cu sulphide ores: variations that result from stockpiling of a nickel-copper sulphide ore in the Sudbury area and its consequences on flotation behaviour, especially in terms of metal losses to scavenger tails. In relation to the first aspect, self-heating characteristics of the stockpile were carried out by monitoring the internal temperatures of the stockpile. Six heat sensors were installed with respect to external conditions in local weather during a 7-month period. Stockpile temperatures were mainly influenced by ambient temperature with some retardation effects. The maximum temperature recorded in the stockpile was 44 °C. Samples taken at the beginning and at the end of stockpiling were tested to assess variations in behaviour of the rougher-scavenger flotation. Relative to the fresh ore, nickel and copper losses in flotation of the stockpile fines were 5.0 and 3.6 %, respectively. The fresh ore yields concentrates with higher nickel grades due to differential flotation behaviour of pentlandite and pyrrhotite relative to the stockpile fines, which exhibit a truly bulk flotation behaviour at least during the first 3 stages.

Aug 1, 2013

By Suguru Kohno, Yoshihiro Momose, Masakazu Honma, Tokirou Kamosawa

Copper metal surfaces have been examined by an extremely sensitive surface analysis technique called temperature programmed photoelectron emission (TPPE). The surfaces were ultrasonically cleaned and subsequently abraded by a screw in organic solvents and water. The TPPE apparatus is composed of a Geiger counter with Q gas (He+ iso-C4H10). The curve of photoelectron emission (PE) intensity vs. wavelength from 300 to 170 nm, termed PE spectrum, was repeatedly measured at different temperatures in the temperature- increase process from 25 to 350°C. The number of emitted electrons in a PE spectrum (PE total count) increased, reached a maximum at-250°C, and decreased with increasing temperature. With the surfaces cleaned alone in the liquids the maximum PE total count decreased in the order C3H70H > (CH3) 2CHOH > C2HpH > CHPH > H2O. With the mechanically abraded surfaces in the liquids the maximum PE total count changed as a function of the abrasion period and the maximum tended to appear at higher temperature with increasing abrasion period; the maximum value at 10-min abrasion decreased in the order H2O > CHpH > C2HPH > (CH3) 2CHOH > n-C3HpH. It was suggested that the TPPE behavior can be related to the acid-base interaction between the alcohols and the abraded metal surfaces and the presence of a contaminant over layer on the surface. From the XPS analysis of the 01 s spectra it was suggested that the chemical change of the adsorbed oxygen to oxide oxygen with temperature plays a substantial role in the appearance of the maximum PE total count.

Jan 1, 2000

By Baisheng Nie, Longlong Yang, Tao Yang, Wenjie Jia

"Gas adsorption in coal is an exothermic and physical process. Temperature might change during the dynamical process. In order to get the temperature variation of gas adsorption process, the experiment system which can test the temperature variation and analyze the thermal effect was established. Gas adsorption experiments under different conditions were done by using the test system. The results show that temperature increases during the adsorption process. It is an exothermic reaction process. Also, the temperature variation and the variation gradient increase with the increasing of equilibrium pressure. The temperature variation value is smaller if the experiment temperature is higher. The paper will provide basic experimental data for explaining gas adsorption mechanism better.INTRODUCTIONChina is the largest coal producer in the world while it also has the most serious coal mine disasters. According to the statistics, there are nearly a thousand coal mines in China including more than 110 the key state-owned mines risking to happen coal and gas outburst. Hundreds of coal and gas outburst occur each year which often causes serious casualties and economic losses (State Administration of Work Safety, 2007). With the continuing exploitation of the coal resources, the depth of the Chinese coal mines increases about 100 meters every year which causes the situation of gas accident becoming more and more serious (Xie et al., 2006).At present, the real mechanism of gas adsorption, desorption and the diffusion process in coal and the influence factor of it are not so clear. And because of the limit of prediction method and the technological level caused gas accident prevention theory and technology not so valid."

Jan 1, 2015

By Khamis Y. Haramy

Curing temperature, density, and moisture significantly affect the velocity measured in the crosshole sonic logging, the rate of strength gain, and the final strength of concrete in drilled shafts and, thereby, affect their structure capacities. Non-destructive field measurements can enhance the QA/QC program by measuring temperature, density, moisture, and sonic velocity of curing concrete during the construction and curing of drilled shafts. The curing environment can greatly affect the concrete strength, and requires close attention during construction. This article shares the experience with the NDE technology used in the QA/QC program in the drilled shaft construction. To understand the mechanism by which a drilled shaft cures under field conditions, two newly constructed drilled shafts were monitored for up to seven days, immediately following concrete placement using the following geophysical logging methods: a) temperature logging; b) crosshole sonic logging; c) gamma-gamma density logging; and d) neutron-moisture logging. One additional drilled shaft was also monitored to a shorter duration. Temperatures were monitored using the sensor in access tubes and/or thermocouples embedded at the center of a drilled shaft and near its reinforcing cage. For a small shaft under 1m diameter, curing temperatures appeared to peak at 41° ? 68° C at different depths at around 24-hour curing time and decreased to and stabilized at around 23° ? 35° C in 6 days. The shaft curing rate varied with depth, shaft diameter, surrounding geo-material types, and the depth of ground water. CSL logging was performed in one shaft from top to bottom from six access tubes and limited monitoring in another shaft. The velocity increased with curing time till 4 to 7 days, and, at a specific time, the velocity appeared to be inversely correlated to curing temperatures. The gamma-gamma density log (GDL) results from 5 different depths were obtained at a source-detector separation of 355 mm. The average density was found to increase with curing time, but decrease slightly in 3 to 5 days. At a given time the GDL density curves seemed to correlate with the neutron monitoring logging (NML) moisture curve. The NML moisture was monitored from 1st to 6th day after concrete placement. The moisture was highest when surrounded by bedrock, then clay, and sand due to different hydration rates.

Jan 1, 2007

By X. Tang, N. Ripepi

The Langmuir model has been widely used for the coal-methane sorption process through an isothermal test. However, even though the temperature-dependent Langmuir model was recognized theoretically and experimentally, the quantitative relationships between the Langmuir constants a and b and temperature have not been clarified and confirmed by laboratory test data. This paper collects 158 methane-coal sorption data under different temperatures that apply the Langmuir model to the relationships between the Langmuir constants a and b and temperature. Even though the Langmuir model cannot be used to show the physical state of methane adsorption on coal, it is widely used because of its simplicity and the reasonable explanation of its parameters a and b. The results from these published isothermal tests indicate that (1) there is no consistent relationship between Langmuir constant a and temperature, (2) the Langmuir model is a temperature-dependent model whose temperature-dependent feature is mainly shown by the relationship between the Langmuir constant b and temperature, and (3) the relationship between the Langmuir constant b and temperature can be described by both exponential and linear relationships with dried coal. This paper provides a database for the temperature-dependent Langmuir model that can be used for the reservoir simulation of coalbed methane reservoirs and for the coal seam degasification modeling of underground coal mines, considering the heating effects induced by geothermal and heat injection through factors such as hot water, hot steam and ultrasonics.

Jan 1, 2016

By N. Ripepi

"The Langmuir model has been widely used for the coal-methane sorption process via an isothermal test. However, even though the temperature-dependent Langmuir model were recognized theoretically and experimentally, the quantitative relationship between the Langmuir’s constants (a & b) and temperature have not been clarified and confirmed by lab test data. This paper collects 158 methane-coal sorption data under different temperatures, which apply the Langmuir model to consider the relationship between Langmuir’s constants (a & b) and temperature (see APPENDIX I). Even though the Langmuir model cannot be used to show the physical state of methane adsorption on coal, it is widely used because of its simplicity and the reasonable explanation of its parameters (a & b). The results from these published isothermal tests confirm that 1) there is no consistent relationship between Langmuir’s constant-a and temperature; 2) the Langmuir model is a temperature-dependent model, and the temperature-dependent feature is mainly shown by the relationship between Langmuir’s constant-b and temperature; 3) The relationship between Langmuir’s constant-b and temperature can be described by both the exponential and linear relationship with dried coal. This paper provides a database for temperature-dependent Langmuir’s model, which can be used for reservoir simulation of coalbed methane reservoir, coal seam degasification modeling for underground coal mines considering the heating effect induced by geotherm and heat injection (via hot water, hot steam, ultrasonic, etc.). INTRODUCTION The isothermal test for gas sorption on coal is one of the fundamental tests in Coalbed Methane (CBM) recovery fields, such as underground coal mine methane degasification, CBM gas-in-place estimation, and carbon dioxide sequestration in un-minable coal seams. Generally, two methods, volumetric and gravimetric, are employed to obtain isothermal data (Bush, A. & Gensterblum, Y., 2012). Based on these two approaches, a series of commercial and self-assembled instruments are built and several calculation methods are used to obtain isothermal data (Bush, A. & Gensterblum, Y., 2012, Gasparik, K., 2014; Goodman, A. L., et al, 2004; Zhang, L., et al, 2013). In the post-processing stage, many models are provided to analyze isothermal data in order to understand the storage mechanism of gas in coal. Common models include the Langmuir model (and its extended forms), the pore-filling model, multilayer adsorption model (BET), and the Gibbs’ model. Among these models, the Langmuir model is the most widely used for its simplicity and functionality. The Langmuir model is expressed as follows:"

Jan 1, 2016

By W. K. Ting, A. Hasan

Mine stope is typically backfilled with cemented paste backfill, which provides a regional underground stability and also a reduction of aboveground tailings accumulation. During backfilling, a phenomenon known as arching occurs and affects the stress distribution of the cemented paste backfill. The change in temperature due to uncontrolled heat transfer from the surrounding rock mass and/or generation from hydration process complicates the stress distribution development of cemented paste backfill. This paper presents results of the investigation on the effects of hydration to cemented paste backfill behaviour when backfilled into a narrow wall model using uncemented paste backfill as controlled sample. The parameters considered include backfill type (cemented paste backfill vs uncemented paste backfill), curing temperature (30°C–60°C), and stress evolution during pouring, consolidation, and curing stages. Results show that uncemented paste backfill re-establishes arching effects more readily, with lower peak stresses and greater stress relaxation than cemented paste backfill, of which its behaviour is significantly influenced by hydration under elevated temperatures. The main outcome of this work is that hydration critically controls the stress-temperature response of cemented paste backfill, and the balance between hydration-driven strength gain and stress relaxation can be leveraged to optimise backfill mix design for safer and more efficient stope filling.

Jan 30, 2026

By B. S. Norris, Charles R. Austin

IN a recent paper the authors1 discussed the reactions to tempering of hypereutectoid steels quenched from 1000° C., as revealed by studies on changes in hardness, electrical resistivity, coercive force and metallographic characteristics. The data, which related specifically to tempering temperatures of 550°, 650° and 710° C., for varying periods up to 125 hr., permitted the following important conclusions: 1. The rate of softening of the steels at the temperatures examined differed markedly although the steels were of "similar" general chemical composition. 2. The temperature of maximum softening spread over a range from about 650° C. to the eutectoid inversion. 3. The divergence in behavior was ascribed, at least in part, to a profound difference in tendency to graphitization on annealing at subeutectoid temperatures. 4. The node of spheroidization of the cementite, as revealed by metallographic studies, also varied considerably in the different steels. The purpose of the present investigation is to pursue further the study of the difference in behavior of the steels on tempering over a wider range of temperature. To this end the following features have received particular attention: 1. Comparison of temperatures of maximum softening of the various steels when the quenched samples were tempered for 5 hr. and for 75 hr. followed by furnace cooling and by quenching in water. 2. Determination of the effect of quenching temperature, prior to tempering, on the rate of softening. Quenching temperatures of 1000° and 850° C. were used in the investigations. 3. Examination of the microstructures obtained with the various heat-treatments employed.

Jan 1, 1938

By Charles Austin

IN a recent paper the authors1 discussed the reactions to tempering of hypereutectoid steels quenched from 1000° C., as revealed by studies on changes in hardness, electrical resistivity, coercive force and metallo-graphic characteristics. The data, which related specifically to temper-ing temperatures of 550°, 650° and 710° C., for varying periods up to 125 hr., permitted the following important conclusions: 1. The rate of softening of the steels at the temperatures examined differed markedly although the steels were of "similar" general chemi-cal composition. 2. The temperature of maximum softening spread over a range from about 650° C. to the eutectoid inversion. 3. The divergence in behavior was ascribed, at least in part, to a profound difference in tendency to graphitization on annealing at sub-eutectoid temperatures. 4. The mode of spheroidization of the cementite, as revealed by metallographic studies, also varied considerably in the different steels. The purpose of the present investigation is to pursue further the study of the difference in behavior of the steels on tempering over a wider range of temperature. To this end the following features have received particular attention: 1. Comparison of temperatures of maximum softening of the various steels when the quenched samples were tempered for 5 hr. and for 75 hr. followed by furnace cooling and by quenching in water. 2. Determination of the effect of quenching temperature, prior to tempering, on the rate of softening. Quenching temperatures of 1000° and 850° C. were used in the investigations. 3. Examination of the microstructures obtained with the various heat-treatments employed.

Jan 1, 1938

By W. G. Davenport

This chapter shows how flash furnace industrial oxygen and oil requirements are affected by different: (a) product temperatures (b) conductive, convective and radiative heat losses (c) electrical energy inputs (d) hydrocarbon fuels. The calculations of the chapter are all for production of 65% Cu matte from pure CuFeS2 concentrate. Blast temperature is? 298 K throughout.

Jan 1, 2001

By J. L. Jambor, E. J. Reardon, E. C. Appleyard, J. A. Cherry

Since the 1957 initiation of deposition of mill tailings at the Heath Steele mine, New Brunswick, periodic detailed studies of the tailings geochemistry and mineralogy have been conducted, thereby providing a unique opportunity to examine the geochemical evolution of a sulfide rich mine>tailings impoundment. When deposited, the tailings contained about 85 wt% sulfide minerals, 1 wt% to 3 wt% carbonate minerals, and 12 wt% to 14 wt% alumino silicate minerals. Mineralogical examination of samples of the tailings from deep in the impoundment indicates that little oxidation occurred prior to tailings deposition. The mill process-water deposited with the tailings was neutral to slightly basic and contained low concentrations of Cu, Pb, Zn and As. Sampling of the tailings five years after deposition indicated that sulfide-oxidation reactions, occurring near the tailings surface, had decreased the tailings-water pH and increased the concentrations of Fe, S042-, Cu, Zn and Pb (up to 10 000 mglL, 25 000 mg/L, 2.5 mg/L, 200 mg/L, and 4.5 mg/L, respectively). In 1975, ten years after decommissioning, the tailings could be divided into three zones: an upper oxidation zone in which sulfide oxidation is actively occurring, a hardpan layer, 15 cm to 20 cm thick, composed of tailings cemented by secondary Fe minerals, and an underlying reduction zone in which the tailings are relatively tin oxidized (Boorman and Watson, 1976). Chemical analyses indicated the presence of low-pH waters containing very high concentrations of SOi-, Fe, and other metals (up to 63 600 mg/L SO42-, 28 600 mg/L Fe, 10 mg/L Pb, 600 mg/L Cu and 4000 mg/L Zn), suggesting that there was a period of intense sulfide oxidation between five and ten years after tailings deposition. More recent sampling, conducted some 20 years after the end of tailings deposition, indicates that relatively little change has occurred in the last ten years, thereby suggesting that the hardpan layer has provided an impediment to the downward movement of dissolved constituents. Analyses of the tailings solids show increased accumulations of many metals at or near the depth of the hardpan layer. Evaluations of the long-term evolution of the tailings can be enhanced by comparison of descriptions of the tailings with descriptions of the gossan that overlay the massivesulfide orebody prior to mining. At Heath Steele, this comparison suggests that many of the mechanisms controlling the distribution of metals in the tailings will probably persist over geologic time.

Jan 1, 1992

By J. L. Jambor, E. J. Reardon, E. C. Appleyard, J. A. Cherry

Abstract- Since the 1957 initiation of deposition of mill tailings at the Heath Steele mine, New Brunswick, periodic detailed studies of the tailings geochemistry and mineralogy have been con­ ducted, thereby providing a unique opportunity to examine the geochernical evolution of a sulfide- rich mine-tailings impoundment. When deposited, the tailings contained about 85 wt% sulfide minerals, 1 wt% to 3 wt% carbonate minerals, and 12 wt% to 14 wt% aluminosilicate minerals. Mineralogical examination of samples of the tailings from deep in the impoundment indicates that little oxidation occurred prior to tailings deposition. The mill process-water deposited with the tailings was neutral to slightly basic and contained low concentrations of Cu, Pb, Zn and As. Sampling of the tailings five years after deposition indicated that sulfide-oxidation reactions, occurring near the tailings surface, had decreased the tailings-water pH and increased the concentrations of Fe, SOi-, Cu, Zn and Pb (up to 10 000 mg/L, 25 000 mg/L, 2.5 mg/L, 200 mg/L, and 4.5 mg/L, respectively) . In 1975, ten years after decommissioning, the tailings could be divided into three zones: an upper oxidation zone in which sulfide oxidation is actively occurring, a hardpan layer, 15 cm to 20 cm thick, composed of tailings cemented by secondary Fe minerals, and an underlying reduction zone in which the tailings are relatively tinoxidized (Boorman and Watson, 1976). Chemical analyses indicated the presence of low-pH waters containing very high concentrations of SO42- , Fe, and other metals (up to 63 600 mg/L SO42-, 28 600 mg/L Fe, 10 mg/L Pb, 600 mg/L Cu and 4000 mg/L Zn), suggesting that there was a period of intense sulfide oxidation between five and ten years after tailings deposition. More recent sampling, conducted some 20 years after the end of tailings deposition, indicates that relatively little change has occurred in the last ten years, thereby suggesting that the hardpan layer has provided an impediment to the downward movement of dissolved constituents . Analyses of the tailings solids show increased accumulations of many metals at or near the depth of the hardpan layer. Evaluations of the long-term evolution of the tailings can be enhanced by comparison of descriptions of the tailings with descriptions of the gossan that overlay the massive­ sulfide orebody prior to mining. At Heath Steele, this comparison suggests that many of the mechanisms controlling the distribution of metals in the tailings will probably persist over geologic time.

Jan 1, 1992

By N McKenzie, E Taylor, S V. L Barrett, H Lagger, A Purwodihardjo

This paper discusses the temporary support design methodology for the largest road caverns ever built in Australia—the Lutwyche Caverns—part of the Airport Link project in Brisbane, Australia. The Lutwyche Caverns with a maximum excavated span of 27 m form a key component of this major road project, allowing on and off ramps merging with the underground highway. In addition to the two large span caverns, a 15 m soft ground tunnel with 5 m cover above the caverns and two 24 m deep burial chambers for the 12.4 m tunnel boring machines (TBMs) had to be built in record time at Lutwyche.The temporary support design methodology involved the use of a range of analytical approaches, including empirical methods to provide a starting point for design development, key block models to determine the potential influence of discontinuities on excavation stability and 2/3D continuum and discontinuum models to determine the potential influence of adjacent excavations and the proposed construction staging on the design. In addition, probabilistic analysis of potential kinematic instability using a discrete fracture network (DFN) approach was also undertaken to establish the critical block loads for the temporary lining, while the continuum and discontinuum models were used to design the support for the 1.5 m diameter rock pillar at the north end of the northbound cavern.The numerical modelling was undertaken in close conjunction with the contractor to develop the optimal construction sequence, considering the available construction equipment on-site and the overall project program requirements. Part of the presentation will further show the applicability of the developed design during construction (deformations, monitoring field observations) and lessons learned for future cavern construction in Australia.CITATION:Lagger, H, Purwodihardjo, A, Barrett, S V L, McKenzie, N and Taylor, E, 2014. Temporary support design for the largest road caverns ever built in Australia – the Lutwyche Caverns, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 399–410 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By R. T. Swinderman

This paper discusses how many of the common practices in conveyor specification and design are out of date compared to the current expectations of users for safe, serviceable, reliable, and fugitive material-free conveyance of bulk solids. Ten of the most common mistakes made in the specification and design stages related to user expectations are reviewed along with the cost vs. price implications of those decisions. A general specification and design hierarchy that designers can use to improve conveyor design is included.

Jan 1, 2010

By J Johansson, J Lööw

There are many reports about how the new technology will affect our work, sometimes they are utopian but often dystopian. Most of the visions describe the industrial work, while the work of the managers does not seem to be affected. In this article, the authors will discuss how the new technology within the concept of Mining 4.0 changes the conditions for leadership and the work of managers in a modern mining industry.

Sep 1, 2024

By S N SHEARD

The use of geophysics in mineral exploration in Australia, and overseas, has increased dramatically over this century. This paper shows that using simple equipment with clever interpretation that the foundations of modem geophysics were laid, using all the same principles. The plethora and diversity of mineral exploration geophysical techniques does not allow a full description of their evolution to be given in such a paper. To convey this evolution, however, the progress of two different geophysical methods, magnetics - a potential field (passive) method, and electromagnetics - an electrical (active) method, are described. Examples of magnetic survey data from the 1920s and more recent vehicle home and airborne surveys are given to show the increase in data quality through technological improvement. A set of four airborne electromagnetic data sets spanning three decades is used to indicate the improvement in electromagnetic techniques. It is argued, that considerable progress is still required in the electromagnetic field to increase its interpretability.

Jan 1, 1992

By Timothy Batchler

"Standing roof supports help to provide a stable working environment in coal mine gateroads. NIOSH participates in the development of these support systems by conducting full-scale tests in their Mine Roof Simulator. These tests have established the performance characteristics of every coal mine support system currently in use in the United States. Through these tests, mine operators and regulatory officials have acquired a fundamental understanding of the various types of support performance that guides the assessment and use of these support systems. However, some little known factors that influence support behavior can lead to misconceptions and, perhaps, a poor assessment of support behavior at times. This paper highlights several of these factors and discusses their significance. The paper also examines a current longwall tailgate support and discusses the inefficiency with this approach. Finally, the NIOSH Mine Roof Simulator (MRS) is the world’s most powerful load frame built specifically to test full-scale roof supports, including longwall shields. are addressed in this paper to provide a more in-depth assessment of the limitations of the MRS and what the MRS testing protocol is designed to do. INTRODUCTION Over the years, considerable research has been conducted to develop standing support technologies and to evaluate their performance characteristics. The load and displacement characteristics of the standing supports have been determined from full-scale testing conducted using the National Institute for Occupational Safety and Health (NIOSH) Mine Roof Simulator (MRS) (Barczak and Tadolini, 2008) located in Bruceton, PA. Performance traits, installation patterns, and ground responses are observed in various geological and mining conditions and are evaluated to determine the support performance in the field (Dolinar, 2010; Campoli, 2015; Zhang et al., 2012). Despite widespread use of standing supports, not every aspect of their performance and resulting ground support capability are always well understood. This paper discusses 10 factors, several of which are surprising, that impact standing support performance."

Jan 1, 2017

By Andrew Case

The Port Nickel facility in Braithwaite, Louisiana, is known for pioneering hydrometallurgical processes for the 'separation and recovery of nickel, cobalt and copper. Ten years ago, in 1985, a new CRI-MET process for the recovery of molybdenum, vanadium, nickel, cobalt and alumina from spent catalysts was developed and implemented. Spent- catalysts from the petroleum industry consietute the majority of feed. These are not only a valuable-source of metals, but due to EPA regulations are frequently classified as hazardous under RCRA. Molybdenum and vanadium are selectively leached in an oxidative hydrothermal step. Alumina is then extracted in a caustic digestive leach. The unique technology produces four primary commercial products l molybdenum trioxide, vanadium oxide, aluminum trihydrate and nickel-cobalt concentrate. This paper discusses the process, modifications. during ten years of operation, and the relationship of these modifications to the future of the catalyst recycling business.

Jan 1, 1995

By A. Lee Barrett

"THE COAL INDUSTRY of the United States• and Canada has made great progress in recent years. Coal mining in •the old days represented one of the most arduous tasks for labour and industry, but over the years great progress has been made in reducing the effort required from labour. Also, the tonnage produced per man, the cost of the coal per ton, and the overall safety of the operation, have been greatly improved.Looking back over the past fifty years:, the era can be divided into four principal parts: (a) hand-loading, (b) track mining methods, (c) off-track mining methods, and (d) continuous mining. For many years, all of the coal was won by hand-mining methods. The first forms of mechanization •resembled the move from the horse •and buggy to the automobile. Early track mechanical mining methods were usually adaptations of the direct methods involved in hand-mining, with each improvement directed toward some specific process. A revolutionary development came about with off-track mining methods. The first efforts in this direction were provided by off-track mechanical loading machines, which loaded the cars •on track and differed from conventional track mining methods only in that the loading machines themselves operated on the mine floor. With the advent -of the shuttle car about ten years ago, true off-track mining came into being, and real progress in this direction began to be made.At the present time we •are at the beginning of a new era -.the era of continuous mining. There will be a period of development with some time needed before the system is generally applied throughout the industry, but -already enough •has been done to indicate rather dearly what the future holds in this direction."

Jan 1, 1953