Search Documents

By Ernst F. Eurich

(Cleveland Meeting, October, 1912.) ALEXANDER PARKES patented in England in 1851-52-53 a process for desilvering lead by means of zinc, making use of the greater affinity of silver for zinc than for lead, discovered by Karsten in 1842. The efforts in England to develop it commercially were not particularly successful, nor was the attempted introduction into the United States. This last was not surprising, as it was about the beginning of our Civil War, and at that period there was very little lead-bullion produced in the united States and there was no field for the process here. There was at that time on Staten Island an establishment that pattisonized lead, probably from Rossie, N. Y., and Chester, Pa., and possibly some Spanish lead, but the production of lead-bullion in the Far West had not yet begun. In 1864, Edward Balbach, of Newark, N. J., patented in this country a process for desilvering lead by means of zinc, and in 1867 Edward Balbach, Jr., patented a " movable black-lead retort with a neck, placed in a furnace," for the purpose of distilling the alloy of zinc, lead, and the precious metals. A brief comparison of the Parkes and the Balbach processes is interesting. The Parkes process as practiced in England consisted in stirring into silver-bearing lead, melted in a kettle, from 1 to 2 per cent. of zinc, cooling, skimming the alloy of lead, zinc, and silver that rose to the surface, liquating it in an iron retort, distilling the residual rich alloy in fire-clay retorts, thus regaining the zinc, and refining the desilvered lead at a low heat in a shallow cast-iron pan that formed the hearth of a reverberatory furnace. If the lead was too impure, it was first softened * Presented also at the Joint Meeting of the Institute and Section IIIa, Metal¬lurgy and Mining, of the Eighth International Congress of Applied Chemistry, New York, September, 1919, and here published by mutual agreement.

Dec 1, 1912

By D. G. E. Kerfoot

In September 1945, when the Lynn Lake nickel orebody was discovered Sherritt Gordon Mines was a small copper mining company with rapidly depleting ore reserves at its single producing mine at Sherridon in the Cold Lake area of Manitoba, 100 miles north of The Pas. The company has been formed in 1927, largely through the efforts of Eldon L. Brown, a 27-year old mining engineer, with the financial backing of Thayer and Halstead Lindsley and the Gordon family. The Lindsleys were American mine promoters who had been successful in the Sudbury area, and the Gordons had extensive interests in the lumber industry in northern Ontario. Carl Sherritt, who gave his name to the company, was an American trapper and prospector who had staked the copper property and sold his interest to the new company. Carl Sherritt died in a flying accident at The Pas in 1928. The Sherritt Gordon Mine started production in 1931, shipping copper concentrate to the new Hudson Bay copper smelter at Flin Flon, Manitoba. In 1931 the price of copper was 18¢/lb. Within a year the price had fallen to 5¢ /lb and the mine was forced to close. It remained closed through the Depression years.

Jan 1, 1999

By Staff

This paper contains an outline of the history of the Sullivan mine, now owned and operated by the Consolidated Mining & Smelting Company of Canada, Ltd.; some account of the various methods by which the ore has been treated in efforts to solve the metallurgical problems which its complex character presents, and, finally, to give, as concisely as possible, an outline of the present mining and metallurgical practice along with a description of the mining and milling plant at Kimberley and the smelter and refineries at Trail, in British Columbia. EARLY HISTORY In May, 1892, Pat Sullivan, John Cleaver and Mike Holland left the Coeur d'Alene country, in the State of Idaho, to seek their fortunes in the Kootenay lake district in British Columbia. They were aided in their venture by James Cronin, afterwards locator and owner of the St. Eugene mine at Moyie. Two months later the party broke up, Sullivan and Cleaver crossing the mountains from Crawford bay on Kootenay lake to the head waters of the St. Mary's river, the course of which they followed down to Fort Steele. Here they found a good deal of excitement about the North Star mine, and, joined by "Ed." Smith, who was familiar with this part of the country, they determined to return and prospect in its vicinity.

Jan 1, 1924

With the employment of a system of ore pillars to support the hanging wall during the mining operations at the North Mine, it was found that, when the stopes were worked out and the pillars remained intact, the main footwall drives developed an undulating longitudinal section due to the shrinkage of the filling in the worked out stopes.These depressions collected water, which made the footwall drives very wet under foot, and everitually worked its way into the pillar workings and the levels below.Water was also finding its way into the shafts because of the silting-up of the level drainage systems and, as both the shafts are down-cast, this tended to increase the humidity of the air entering the mine.To overcome these troubles it was decided to try a system of siphons as a method of subsidiary drainage.SYSTEM AT PRESENT IN USE.All drainage water is collected as near to its source as possible, run into a sump in an adjacent low lying part of the level, and continuously removed from these sumps by a siphon system.Each level has its own system. Water is collected from the sumps by a 1-in. pipe and delivered to a pipe running the length of the level along the back of the footwall drive. At the shaft the pipe is increased to...

Jan 1, 1938

By B Cope, Y Churi

Roxgold was a small exploration company when it discovered the Zone 55 orebody at the Yaramoko project in Burkina Faso in 2010. Since this time, it has actively progressed the project with the completion of a preliminary economic assessment in 2013, a feasibility study in early 2014 and obtained full permitting for construction in January 2015. With no other underground gold mine in Burkina Faso, developing a modern and productive modern gold mine in West Africa was considered a significant challenge as Roxgold moved from explorer to producer.To facilitate this development, Roxgold engaged an international underground mining contractor to partner this development. This has enabled Roxgold to successfully develop the mine over a relatively short time frame with construction commencing in April 2015, first gold being poured in May 2016 and commercial production being achieved in October 2016.This paper discusses key elements of the project development and highlights some of the challenges faced with operating in a remote poorly developed area with a limited mining culture. Furthermore, the authors highlight the key technical and operational aspects that make the Yaramoko project a very successful development project.CITATION:Cope, B and Churi, Y, 2017. The development of the Yaramoko gold project in Burkina Faso, West Africa, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 173–182 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

By P. D. Hodgson, G. L. Kelly, H. Beladi

"The formation of ultrafine ferrite by strain induced transformation is assessed using rolling and hot torsion experiments. These experiments are used to examine the impact of thermomechanical processing conditions and steel chemistry on strain induced austenite to ferrite transformation and the formation of ultrafine ferrite. The critical strain for dynamic strain induced transformation increased with increasing carbon equivalence, deformation temperature and austenite grain size. The deformation structure in the austenite grains changes with the thermomechanical processing conditions.Drawing on these results and the current literature, the important factors for the production of ultrafine ferrite are described and a mechanism proposed."

Jan 1, 2004

By Philani Larrance Ngwenyama, Ronald CW Webber-Youngman

The survival chances of trapped miners in underground mines depend on how quickly they can be located and rescued post-accident. During entrapments, emergency rescue is highly desired but can be hindered by the lack of positioning information when a fit-for-purpose missing-person locator system is not available. Various types of missing-person locator systems are available to aid search-and-rescue operations. From the wide range of the available systems, selecting the most suitable one becomes the next challenge. The available systems have not been measured if they are fit-for-purpose or not, and to what situation. This study proposes user requirements that can be used as a guideline to facilitate the system selection process. These user requirements provide a framework for the design and development of a fit-for-purpose missing-person locator system. The user requirements can also be used for evaluating the performances of a particular system, predict its success, and also drive future research toward developing new technology to enhance the capabilities of the current systems.

Apr 1, 2024

By Ronald C. W. Webber‑Youngman, Philani Larrance Ngwenyama

Entrapments are a huge risk in underground mines. This happens when miners (or any other persons who have entered underground) survive the initial event of an accident, become trapped or lost in unknown and life-threatening locations after evacuation, and remain unaccounted for. At this point, every second counts, and emergency response is highly desired for any chances of saving survivors. The survival chances of the missing persons depend on how quickly they can be located. Rescue teams are often deployed to search for the missing persons underground. However, the rescue teams are forced to search in random and presumed areas of the mine. This is due to the unavailability of information pertaining to the whereabouts of the missing persons. Not only the provision of accurate locations, but various other types of information such as post-accident two-way communication can enhance the survival chances of the missing persons. This information can be provided by a fit-for-purpose missing person locator system. A wide variety of missing person locator systems are already commercially available, some are in testing phases and others in prototype and development phases. This includes tracking, tracing, location detectors and post-accident two-way communication systems. These systems have unique functionalities, capabilities and limitations; making it difficult for mines to select the most effective, applicable and suitable system specific to their mine. In this study, the user requirements for a fit-for-purpose missing person locator system were developed. The purpose of the user requirements was to provide a guideline to facilitate the system selection process. The user requirements can also be used as a tool to measure and evaluate the performance of the selected missing person locator system. The user requirements were also used to predict the success of the selected system under different missing person incident scenarios. The development of the user requirements showed a potential for many other benefits for missing person locator systems.

Nov 2, 2023

By K. H. McDaniel

An interactive mine ventilation simulation software program (WIPPVENT) was developed at the Waste Isolation Pilot Plant (WIPP). The WIPP is a U.S. Department of Energy (DOE) research and development project located near Carlsbad, New Mexico. The facility is designed to provide a permanent, safe underground disposal of U.S. defense generated transuranic waste in bedded salt. In addition to its regular functions, the underground ventilation system is engineered to prevent the uncontrolled spread of radioactive materials in the unlikely event of a release. To enhance the operability system, Westinghouse Electric Corporation has developed an interactive mine ventilation simulation software program (WIPPVENT). While WIPPVENT includes most of the functions of the commercially available simulation program VNETPC (copyright © 1991 Mine Ventilation Services, Inc.), the user interface has been completely rewritten as a Windows ® application and screen graphics have been added. WIPPVENT is designed to interact with the WIPP ventilation monitoring systems through the site wide Central Monitoring System.

Jan 1, 1996

By K. Sun, S. A. Argyropoulos

The assimilation and the exothermic behavior of Zn-Zr metallic powder compacts into molten aluminum was studied by measuring simultaneously the temperatures inside at the centerline of the compact, at its surface, and inside the molten aluminum bath, as well as the net downward force acting on the compact. In addition, the exothermic behavior of these compacts was also investigated in an argon protected atmosphere. The temperature rise inside the compact increases significantly with the mass ratio of zirconium in the compact and to a lesser degree with the aluminum bath temperature. Experimental results on the recovery of these compacts in molten aluminum will also be presented.

Jan 1, 2008

By R Goddard

An alternative stoping method has been adopted for narrow vein stoping at the Tasmania Mine in Northern Tasmania. Colloquially described as ‘Radial-in-Reef’ (RiR) stoping, the method employs the drilling of radial rings in the plane of the Reef from a drill stub located at the geographic centre of the proposed stope panel.Production from the Western Zone of the Tasmania Reef has been undertaken remotely from the Reef since 2007, after a detailed geotechnical engineering analysis indicated that the integrity of the sill drives could not guarantee an acceptable level of confidence should an anticipated seismic event occur within a radius of 10 m. The key tenet of the remote mining approach was the exclusion of personnel from sill drives once stoping had commenced. The remote mining method had to be ‘retrofitted’ to four existing stoping blocks totalling 11 sill drives which totalled 160 m vertically. The remote mining method proved to be complex, cumbersome and very expensive. However, the ore was extracted successfully.By early 2010, previously developed ore had largely been exhausted and the future development with an orebody open at depth presented the opportunity to review the current extraction method. However, the new extraction method needed to maintain the tenet of excluding personnel from sill drives of active stoping blocks, but seek opportunities to reduce the difficult and costly aspects of the previous method. The new ‘Radial-in-Reef’ stoping reduced the development requirement from six to two drives per ore block. Cost implications aside, the significant reduction in prestoping extraction ratio was expected to also reduce the likelihood of seismicity. Transverse production rings were designed to be drilled radially from a drill stub mined from a mid-stope footwall drive. Stopes totalling up to 7000 tonnes were planned be fired in a single electronic blast. Extraction was designed to take place from a basal sill drive under teleremote operation. At the time of writing, the method was under trial.

Mar 21, 2011

By Claudio Barsotti, Leonard C. Kitchener

INTRODUCTION The major mining operations of the Ontario Division of Inco Metals Company are located in the Sudbury Basin. Around the rim of this geo- logical formation and within thirty miles of the City of Sudbury are located eleven under- ground mines of the Company, two of which are on standby. In addition, there is one mine in Northwestern Ontario at Shebandowan, 1127 Km (700 miles) northwest of Sudbury. In 1980 ore production totalled 10.6 x 10 mt (11.7 million tons) from underground and open pit operations. Underground mining methods include blasthole, vertical retreat, sublevel caving, cut-and-fill and undercut-and-fill. Inco reduction operations in the Sudbury area include two concentrators, one smelter, one iron ore recovery plant, a copper refinery a nickel refinery and a high purity plate rolling mill. As well, an electrolytic nickel refinery is located on Lake Erie at Port Colborne, near Niagara Falls. In the Sudbury District, Inco employees total 14,278 of whom 6,490 are directly employed in the mining and milling operations. I T H DRILLING Background - The use of long blastholes in underground operations at Inco mines in the Sudbury district started more than 30 years ago at the Levack Mine. At that time, diamond drills were used to mine ore by open stoping and for pillar recovery. By the 1950's the concept had been extended to all mines. The heavy percussion drill was also developed by this time and led to the acceptance of the 11.43 cm (4% in.) piston diameter drifter for bar and arm and fan drill applications. The use however, of the nominal 5.08 cm (2 in.) diameter blastholes drilled radially from the level or sublevel causes overdrilling at the periphery. As well, the smaller holes are subject to hole deviation, are difficult to drill beyond 38.1 m (125 ft.) and require the need for several drilling horizons or sublevels. The need to improve blasthole stoping techniques and our experience with large diameter blastholes in open pit mining led to the trial of an I T H drill in 1962. The test was unsuccessful however, since button bits were not available at the time and the tungsten carbide cross bit experienced short life, gauge loss, and caused hole deviation and poor penetration rates. The successful application of the raise borer beginning in 1964 and the ability to drill 20.32 cm (8 in.) to 27.94 cm (11 in.) diameter pilot holes led to the development of smaller, more portable, rotary drills for blasthole mining. As a result, a mining method based on the use of 20 cm (7 718 in.) diameter, 60.1 m (200 ft.) long rotary blastholes was developed and tested successfully at our C.C.North Mine. Between 1972, when the method was first tested, and 1973 over 4572 m (15000 ft.) of large holes were drilled with rotary drills in the recovery of 175,960 mt (194000 tons) of primary stoping and pillar remnants. A new mining method was developed that made use of this large hole drilling equipment. Instead of longhole carbide drilling by bar-and-arm or fan drill set-ups at sublevels, the large diameter holes were drilled full stope height from the top sill, which substantially reduced development, drilling time and improved fragmentation. These drills however, were difficult to move and set-up, and had a high maintenance cost and low productivity. The capital outlay and extensive technical development required to improve these drills and reduce the high drilling costs however, was economically unattractive. New development in drills and button bits INTRODUCTION The major mining operations of the Ontario Division of Inco Metals Company are located in the Sudbury Basin. Around the rim of this geo- logical formation and within thirty miles of the City of Sudbury are located eleven under- ground mines of the Company, two of which are on standby. In addition, there is one mine in Northwestern Ontario at Shebandowan, 1127 Km (700 miles) northwest of Sudbury. In 1980 ore production totalled 10.6 x 10 mt (11.7 million tons) from underground and open pit operations. Underground mining methods include blasthole, vertical retreat, sublevel caving, cut-and-fill and undercut-and-fill. Inco reduction operations in the Sudbury area include two concentrators, one smelter, one iron ore recovery plant, a copper refinery a nickel refinery and a high purity plate rolling mill. As well, an electrolytic nickel refinery is located on Lake Erie at Port Colborne, near Niagara Falls. In the Sudbury District, Inco employees total 14,278 of whom 6,490 are directly employed in the mining and milling operations. I T H DRILLING Background - The use of long blastholes in underground operations at Inco mines in the Sudbury district started more than 30 years ago at the Levack Mine. At that time, diamond drills were used to mine ore by open stoping and for pillar recovery. By the 1950's the concept had been extended to all mines. The heavy percussion drill was also developed by this time and led to the acceptance of the 11.43 cm (4% in.) piston diameter drifter for bar and arm and fan drill applications. The use however, of the nominal 5.08 cm (2 in.) diameter blastholes drilled radially from the level or sublevel causes overdrilling at the periphery. As well, the smaller holes are subject to hole deviation, are difficult to drill beyond 38.1 m (125 ft.) and require the need for several drilling horizons or sublevels. The need to improve blasthole stoping techniques and our experience with large diameter blastholes in open pit mining led to the trial of an I T H drill in 1962. The test was unsuccessful however, since button bits were not available at the time and the tungsten carbide cross bit experienced short life, gauge loss, and caused hole deviation and poor penetration rates. The successful application of the raise borer beginning in 1964 and the ability to drill 20.32 cm (8 in.) to 27.94 cm (11 in.) diameter pilot holes led to the development of smaller, more portable, rotary drills for blasthole mining. As a result, a mining method based on the use of 20 cm (7 718 in.) diameter, 60.1 m (200 ft.) long rotary blastholes was developed and tested successfully at our C.C.North Mine. Between 1972, when the method was first tested, and 1973 over 4572 m (15000 ft.) of large holes were drilled with rotary drills in the recovery of 175,960 mt (194000 tons) of primary stoping and pillar remnants. A new mining method was developed that made use of this large hole drilling equipment. Instead of longhole carbide drilling by bar-and-arm or fan drill set-ups at sublevels, the large diameter holes were drilled full stope height from the top sill, which substantially reduced development, drilling time and improved fragmentation. These drills however, were difficult to move and set-up, and had a high maintenance cost and low productivity. The capital outlay and extensive technical development required to improve these drills and reduce the high drilling costs however, was economically unattractive. New development in drills and button bits

Jan 1, 1981

By P. Hanniala, J. Sulanto

"The requirement for the reduction of sulphur dioxide emissions from copper smelters is becoming more and more important. Therefore, the most important question in smelting technology will be how to produce even, high strength SO2 gas in smelter and how to combine smelting and converting. The best sorution in certain cases is to eliminate converters totally.Outokumpu is already responding to this challenge. As a result of extensive research work, Outokumpu Oy has developed the Flash Smelting Process for direct smelting of blister copper from concentrates in one step.The newest process development is the Kennecott-Outokumpu Flash Converting process, where solidified copper matte is converted into blister copper. The production of low volume high SO2 content gases, separation of smelting and converting operations to allow increased on-line availability, and simplified process control are the major benefits of the process which translates to reduced smelter capital and operating costs.Also, it has been studied the use of the same Outokumpu furnace for smelting and converting alternately when the production capacity is low.In this paper, the developments and improvements of the Outokumpu Process are described from the operation and investment cost standpoints"

Jan 1, 1988

By Oswald J. Heinrich

THE great improvements which have been made in late years in the different systems and instruments used to perforate the crust of the earth for purposes of testing and exploring for mineral resources or for other reasons, by means of bore-holes of greater or less diameter and to greater or less depths, are manifold. It may therefore be of interest to make an impartial comparison of them, or of such as are most commonly used. Being well aware of the difficulties which are encountered in such a task, a reasonable allowance must be made in such a comparison. It is a rare instance when even two decidedly different systems or instruments have been used in the same locality, penetrating identically the same strata to the same depth. The diameter of a borehole as well as its greater or less depth must also be considered in regard to its cost per foot, etc. But for practical purposes, for ex¬ploration at least, we may assert this rule Any borehole, of whatever diameter, which allows the means of examining the strata most carefully and completely, will be sufficient for this purpose, but that one which will do it most economically and in the least space of time, must be considered the best for it. It will, therefore, partially depend upon circumstances, what system, in spite of other superiorities, may be the best in each case, and the following remarks may aid in deciding this question. To make the attempt here to review all that has been published upon the different systems and means of boring would be out of place. Reference can be had to the able publications treating upon this subject. A difference in this respect exists in regard to the use of the hollow rods in connection with the diamond drill, used for that purpose. The great future, which appears to be evident for this instrument, will be warrant enough for any one, who has had the opportunity to test it, to give his experience to the public. Only in this way can we bring this system to such perfection, as it seems to deserve and * The drawings illustrating this paper are one-half the size of the tools represented, with the exception of the instrument used to reverse the current in the bore-hole (Fig. 17), which is one-third the actual size.

Jan 1, 1874

By R. Alford

In the modern world of demolition safety is paramount and unnecessary or unquantifiable risks are not accepted (FasterCapital, 2024) and all risks must be kept As Low As Reasonably Practicable (ALARP) (BSI, 2017). This principle has led to a huge reduction in deaths in the last 50 years and the statistics continue to improve although this is starting to plateau (Beal, 2007). Under normal circumstances, this is now simply part of the normal way work is done and systems are in place to ensure both safety and economic profits are assured. What happens when the environment is less controlled and risks are unknown, such as after a natural disaster, war, an accident or a stand-up from a failed demolition attempt? A dangerous structure cannot responsibly be left alone with a fence around it so some action must be taken, but how can this be done safely and responsibly? An incident in Didcot, England in which half of a power station’s boiler house being prepared for an explosive demolition collapsed suddenly, killing four men in 2016 provides a useful case study of how technology, creativity and planning can be used to conduct complex demolition fully remotely to avoid any further risk to life.

Jan 21, 2025

By AIME AIME

THE annual meeting of the A.I.M.E. was fittingly closed with a joint meeting of the Metropolitan sections of the four National societies on Feb. 18, at which this subject was adequately discussed by leading engineers before an audience that completely filled the Engineering Auditorium. The large amount of publicity that has been given the Diesel electric loco- motive, and the often garbled reports of its performance and possibilities that have been circulated, makes it particularly fitting that the facts should be given the profession as determined by those who have aided in developing and operating this latest form of prime- mover in railroad operation. C. A. Stein, general manager of the Central R. R. of New Jersey, opened the meeting with a discussion of the problem of electrification, and the relation of the short haul, switching, and terminal service to heavy electrification. Referring directly to the problem of the Central R. R. of New Jersey, some subtitution for the steam locomotive is necessary within the city limits of New York because of local ordinances against the smoke nuisance. While the improvement in the design of the steam locomotive has been marked-the efiiency today is over fifty times that of the locomotive of 100 years ago-it has now probably reached the point of maximum perfection. If anything, it is open to the criticism of having Coo many appliances to get out of

Jan 1, 1926

When a thin film of volatile matter is deposited under vacuum on a polished coal surface, and the coated surface is examined microscopically in plane-polarized reflected light, colour changes are observed which are characteristic of the various macerals present. The colour changes appear to be mainly due to interference between light reflected at the upper surface of the film and at the film!coal interface. A variety of source materials for the volatile matter required have been tested, including powdered bituminous coal, coal tars, boron oxide, and certain resins. Bituminous coal gave the best results.

Jan 1, 1970

By T. Narita

The diffusion barrier coating system (DBC system) was designed to suppress interdiffusion between alloy substrate and coatings in addition to ensuring slow oxide growth at high temperatures. In this report the concept of the DBC system will be introduced, and the results obtained for various heat-resistant alloys are presented. In this DBC system the s-phase of the Re-Cr-Ni system was selected as the barrier and is formed by electroplating Re-Ni and Ni films from aqueous solutions, followed by Cr and/or Al pack cementations. A typical DBC system consists of Ni-base superalloy / triple s-Re based alloy layer / ?’-Ni3Al and/or ß-NiAl (with or without Pt addition) / a-Al2O3. It was found that the DBC system maintained its structure for long time exposures because the s phase has tie-lines with the ? and ?’ alloy substrate and the ?’ and/or ß coating. The s-Re based alloy can suppress both the inward Al diffusion and the outward diffusion of alloying elements. The DBC system was successfully applied to various heat-resistant alloys such as Ni-Mo and Fe-Cr-Al based alloys, and these alloys with the DBC system were creep-deformed slowly under external applied stresses. A simultaneous diffusion coating process for Al and Hf was developed using Hf+NH4Cl+Al2O3 pack cementation. To obtain reliable and long-life coatings the combination of alloy substrate, coating, and external scale should be considered as a total system, to optimize oxidation resistance, structural stability, and mechanical properties.

Jan 1, 2010

By F. E. Harris

IT has been said that carbon is "ubiquitous" with reference to iron alloys. Certainly at temperatures where carbon and iron form the solid solution, austenite, it may be readily added to, or removed from, steel surfaces. Differences in concentration potential are the sole requirements for carbon flow. To measure the rate of carbon flow, a proportionality factor, D, is arbitrarily expressed in units of (length)2 X (time)-1. If the term used for carbon concentration is weight pct C, as is customary, then a factor must be found, changing this term to one of weight per unit volume when the diffusion coefficient, D, is used in flow formulae. The determination of D values for carbon is complicated since D varies with the concentration itself. The Matano method has often been employed for systems involving a variant D. This method expreses an evaluation of unsteady flow whereby .0 is given a relationship with the numerical value of C-X slopes. The author contends that this solution is incorrect, except when D is invariant. The primary purpose of this paper is to support this contention. Here diffusion is controlled under two conditions of flow. The first part deals with the steady state; the second part considers unsteady flow under definite restrictions. Beginning with the fundamental concept, the development is continued until equations for C-X curves are obtained. The solution is then subjected to experimental data. It is realized that a great amount of reliable data is required for a rigorous proof. No such research is claimed. Instead an attempt is made to set forth the physical significance of the diffusion mechanism, and particularly to express the factors which influence the flow of carbon in austenite. Of equal significance is the implication that gaseous media may be employed with reasonable accuracy in making these determinations. THE STEADY STATE DIFFUSION OF CARBON IN AUSTENITE The fundamental experiment defining diffusion in solid metals may be readily performed for carbon in gamma iron.1 For this experiment a thin plate of medium carbon steel is chosen. The surfaces of this plate may be taken as two parallel planes which may be considered infinite for points well in the center of the planes. These two planes are held at different concentrations of carbon at a constant temperature. This temperature, 1700°F for example, is one where the single phase, carbon in solution with gamma iron, exists. When these conditions are held for a sufficient time the concentration of carbon of the different points of the solid settles down towards its steady state value. At points well removed from the ends, the concentration will remain the same along planes parallel to the surfaces of the plate.

Jan 1, 1947

By Kurt Herzog

State-of-the-art automation information technology and connectivity enables the digitalization of steel production that goes far beyond conventional automation of industrial production. Initiatives have been started around the globe to foster digitalization like IIoT (Industrial Internet of Things) in the US, Industrie 4.0 in Germany or China 2025. Primetals Technologies is actively driving the digitalization shaping the future of steel production. Intelligent combination of sensor technology combined with digital models as well as quality and production planning and control systems leads to new dimensions in product quality and production cost reduction. New diagnostic ways allow intuitive fault tracing or processing to support faster maintenance. Digital assistants support both operation and maintenance using context-oriented or self-learned information.

Oct 30, 2017