Search Documents

This paper focuses on the dissolution of various Manganese based compact additions into liquid Magnesium. The experimental procedure employed cylindrical compacts with various Manganese compositions. The various temperatures of the additions and the Magnesium bath were measured simultaneously during the immersion of the additions into Magnesium bath. The exothermicity level of these additions during their dissolution into liquid Magnesium was determined. The relation of the exothermicity level with the dissolution kinetics was also examined. In addition, SEM and EDX work was conducted for additions, which were withdrawn from the Magnesium bath. Finally, the recovery of these additions was estimated by taking samples from the Magnesium bath and conducting ICP analyses.

Jan 1, 2006

The dissolution kinetics of cobalt in iodine/iodide solutions was investigated using a rotating disc technique. Variables studied here included temperature, rotating speed, concentration of lixiviants, and pH of the solution. The overall dissolution reaction was found to be limited by mass transfer of tri-iodide through the diffusion boundary layer with Arrhenius activation energy of less than 16.2 kJ/mol (4 kcal/mol) over the temperature range, 2-42°C. The pH of the solution had little effect as long as the pH of the solution was less than 8. However, when the pH of the solution became greater than 8, the dissolution rate decreased dramatically due to passivation. The rate of dissolution was in good agreement with the dissolution model developed by the authors earlier.

Jan 1, 1994

By Y. Guan

The dissolution behavior of copper and gold from their pure state and from Au/Cu alloys in cyanide solutions has been investigated using a rotating disc. Oxygen was used as an oxidant. The effect of the composition of the alloys, stirring speed of the disc, concentration of lixiviants and temperature on the overall dissolution kinetics has been studied. Gold/copper alloys of three compositions were used in this study. The atomic percent of gold in these alloys was 75, 50 and 25, respectively. The dissolution behavior of these three alloys was compared with that of pure gold and of copper under the same chemical conditions. In general, the dissolution of copper and gold from alloys is partially controlled by surface chemical reaction and largely by mass transfer.

Jan 1, 1992

By R. DasGupta

The dissolution behavior of gold in ammoniacal solutions at 75°C has been investigated. The variables investigated include concentration of lixiviants, pH of the solution and various oxidants. The anodic dissolution of gold was studied in the absence of oxidants using the potentiodynamic polarization technique. The cathodic reaction of oxidants was studied on a platinum electrode. Tafel polarization tests were also performed to determine the dissolution rate. The overall dissolution of gold in ammoniacal solutions was examined using a mixed potential theory. A comparative study on the role of cupric am mine, oxygen, hydrogen peroxide, sodium hypochlorite as oxidants for the dissolution of gold in ammoniacal solutions has been carried out.

Jan 1, 1996

By Y. Guan

The dissolution behavior of silver and copper from silver/copper alloys in ammoniacal solutions has been investigated using a rotating disc. Oxygen was used as an oxidant. The effect of composition of alloys, concentration of lixiviants, stirring speed and temperature on the overall dissolution kinetics has been studied. Silver / copper alloys of three compositions were used in this study. The atomic percents of silver in these alloys were 76.9, 46.9 and 24.1. The results on the rate of dissolution obtained for these alloys have been compared with that of pure silver and copper under the same testing conditions. A particular emphasis has been given to the galvanic effect on the overall dissolution rates.

Jan 1, 1993

By Y. Guan

The dissolution behavior of silver in ammoniacal solutions with cupric ammine as an oxidant has been investigated using a rotating disc electrode. The rates of dissolution of silver were determined by an electrochemical means as well as a direct measurement of silver ions reported in the bulk solution as a function of time. The variables investigated included stirring speed, temperature, concentration of lixiviants, and pH of the solutions. The rate of dissolution under the conditions studied' was found to be controlled by an electrochemical reaction at the liquid/ solid interface with an apparent activation energy of 48.07 kJ /mole. The rate was found to be a half order with respect to the, concentration of cupric tetra-ammine, Cu(NH3)l+.; The results were explained in terms of a mixed' potential theory.

Jan 1, 1994

The dissolution kinetics of gold in iodide solutions with oxygen in an autoclave was investigated. The leaching process was described by a gas-liquid-solid heterogeneous reaction. The effect of stirring speed, temperature, partial pressure of oxygen, and concentration of lixiviants on the overall leaching rate was investigated. It was found that the dissolution of gold was limited by a heterogeneous chemical reaction. The apparent activation energy was measured to be 34.7-54.3 kJ/mol under the conditions studied. Experimental findings were in good agreement with the kinetic model proposed.

Jan 1, 1996

By K. T. Aye

An investigation into the leaching of chalcocite and covellite in cyanide solutions at concentrations typically encountered daring gold cyanidation has been conducted. The results indicate that, for both minerals, the extent of leaching is greater under anoxic conditions, but is still incomplete even in the presence of free cyanide ions, with undissolved copper solids remaining in equilibrium with solution species. The speciation of the sulfur and cyanide reaction products in solution are interpreted in terms of the fast formation of a copper(I)- cyanide complexes in solution and a sulfur-rich copper(I) polysulfide solid phase, which then reacts more slowly to produce thiocyanate ions.

Jan 1, 2011

By A. O. Filmer

A study of the dissolution of gold from a pyrite concentrate and from various calcines is reported. The percentage extraction of gold was found to decrease with increasing sulphur content in the material leached because of the porosity of the materials, and particularly because of the passivation of the anodic dissolution of gold when the gold was In contact with other conducting minerals. This is explained in terms of the current-potential curves for the oxidation of gold and the reduction of dissolved oxygen.

Jan 1, 1982

By J. E. Dutrizac

The dissolution of low-iron sphalerite, (Zn,Fe)S containing 0.08% Fe, in ferric sulphate-sulphuric acid media was investigated using closely sized fractions of crushed sphalerite crystals and sintered disks made from the crushed crystals. Linear kinetics are observed, and the predominant reaction products are ZnSO4, FeSO4 and elemental sulphur. The leaching rate increases systematically with increasing temperature, and the calculated apparent activation energy is 56 kJ/mol for the sized sphalerite and 54 kJ/mol for the sintered disks. The relatively high apparent activation energy suggests that the rate is chemically controlled, a conclusion supported by the insensitivity of the rate to the disk rotation speed. The rate increases as the 0.22 power of the Fe(SO4)1.5 concentration, and as the 0.22 power of the H2SO4 concentration. However, in the absence of ferric ions, the rate increases more significantly with increasing H2SO4 concentrations, and relatively rapid rates are observed in solutions containing >0.5 M H2SO4. In 0.1 M Fe(SO4)1.5-0.3 M H2SO4 media, the measured rate decreases with increasing sulphate concentrations, added as Li2SO4. The rate of dissolution of low-iron sphalerite is promoted by dissolved copper concentrations as high as 800 mg/L. In contrast, dissolved silver, even in the 0-2 mg/L concentration range, significantly retards the dissolution of the low-iron sphalerite.

Jan 1, 2008

By Luis M. Chia

The direct dissolution of zinc in an organic solution of di-(2-ethylhexyl) phosphoric acid (D2EHPA) and kerosene was studied. The objective was to gain a better understanding of the fundamentals involved in the anodic step of the galvanic stripping process. Results showed that metallic zinc does dissolve spontaneously at ambient temperature by an electrochemical mechanism and the presence of additional oxygen activated the process. When oxygen was removed by prior nitrogen sparging, dissolution did not occur indicating a depolarizing cathodic reaction is necessary. The concentration of water in the organic also affected the rate of dissolution. A factorially designed experiment was made using four variables at two levels selected by evaluating results from previous screening tests. D2EHPA concentration, surface area and agitation were all found to be significant for the values chosen. Temperature was less significant and it was found that zinc dissolution is probably a diffusion or mixed controlled process, as indicated by the calculated activation energy of 6 kcal/mole.

Jan 1, 1995

By O. G. Olvera, D. G. Dixon, E. Asselin, L. S. Quiroz

Dissolution rates of chalcopyrite (CuFeS2) were calculated using electrochemical impedance spectroscopy (EIS). The calculated dissolution rate decreased by a factor of 3.2 after the electrode was passivated. The results presented in this work indicate that the reduction of Fe3+ was the rate-controlling step for fresh CuFeS2 electrodes while the transport of cations within the passive film limited the dissolution rate for the passivated electrode. The transfer of cations at the electrode/electrolyte and passive film/electrolyte interfaces did not affect the dissolution rates of the fresh and passivated CuFeS2 electrodes, respectively. The catalytic effect of pyrite (FeS2) on the dissolution of CuFeS2 continued after the passivating treatment. The contact of fresh and passivated CuFeS2 electrodes with different FeS2 particles resulted in increased dissolution rates, due to an increase in the reduction rate of Fe3+.

Jan 1, 2014

By I. I. Betcherman

INTRODUCTION A DISTILLATION process offers one of the most effective methods of refining metals. Its use is particularly attractive in the case of reactive metals which are not readily treated by pyrometallurgical or electrolytic methods. The 1ow vapour pressure of most metals severely restricts the applicability of the disti1lation process and only one or two metals may be effectively treated under atmospheric pressure at a reasonable temperature. If operations are carried out under reduced pressure several additional metals may be effectively distilled. Table I shows the vapour pressure of a number of metals together with a value of the free energy of formation of their ?oxides. Zinc and cadmium head the list and for many years? they have .been effectively refined by distillation. Sodium, magnesium, and calcium follow in descending order, and they may be distilled readily in vacuo and with difficulty at atmospheric pressure. Sodium, which is not of great metallurgical interest, is not considered. Magnesium has recently been produced in considerable tonnages by distillation methods ( 3). This paper describes the vacuum distillation of magnesium and calcium, their separation from each other, and their separation from less volatile impurities.

Jan 1, 1951

By William A. Rehrig

During recent years, there have been frequent investigations on the geochemistry of biotite. This work has emphasized, and no doubt was prompted by, factors related to mineral exploration, particularly for those deposits of the porphyry copper type. A large number of papers have been devoted to the obtainment of trace-element data from plutonic biotite. These data have been used to extract primary geochemical information pertaining to the parent magna and the hydro-thermal system which together give rise to porphyry copper deposits. In two early works, Putman and Burnham (1963) and Parry and Nackowski (1963) analyzed base metal contents of ferromagnesium minerals, primarily biotite, from various barrenfmineralized plutons of the Basin and Range Province. One similar conclusion from the two studies was that the Cu, Zn, and Pb contents of magmatic biotite served as indicators of ore development within the granitic rocks genetically related to ore. This theme was then pursued vigorously by a number of authors until the present time. Results, however, have been contradictory, as reviewed by Coope (1974). For example, studies by A1 Hashimi and Brownlow (1970), Lovering et a1 (1970), Putman (1972), and Graybeal (1973) continued to support positive primary relationships between the trace-metal content (usually copper) of biotite and associated sulfide mineralization. By studying biotite in close spatial association will sulfide occurrences, Putman (1972) and Graybeal (1973) developed models for base metal partitioning in magmatic systems based on their discovery of inversely distributed copper between silicate (biotite) and sulfide phases. Conversely, research by Bradshaw (1967) and Blaxland (1971) plus the recent findings of Parry and Jacobs (1975) and Kesler et a1 (1975) found little if any evidence to support a correlation of biotite base-metal or

Jan 1, 1976

By W. V. Swarzenski

In its, effort to combat waterlogging and coil salinity, the later and Soils Investigation Division of WAPDA (West Pakistan's Water and Power Development Authority) has carried out an extensive program of test drilling and water sampling, since 1954. Data collected during the past ten years have permitted the delineation of fresh and saline ground-water-zones in the Punjab Plain. Fresh ground water containing generally, less than 500 ppm (parts per million) of total dissolved solids is found in wide belts paralleling the major rivers and in other areas of fresh-water recharge. Locally, fresh ground water extends to depths of 1,500 feet and more. Saline ground water occurs downgradient from sources of recharge, particularly in the lower central parts of the interfluvial areas and, presumably, underlies most of the Punjab Plain. The ground waters of the Punjab are characterized by their evolution from calcium, magnesium bicarbonate waters, near sources of recharge, to waters containing a dominant proportion of sodium. The highly mineralized waters of the Punjab are generally of the sodium chloride type, whereas in Dera Ismail Khan District sodium sulfate waters predominate. The pattern of distribution of saline ground-water zones and the observed gradual increase in mineral content, downgradient from sources of recharge, can be explained best by a hypothesis stressing the processes of evaporation from the water table and solution of minerals within the alluvial aquifer.

Jan 1, 1967

By A. Malfliet, A. Van den Bulck, D. Willems, M. Guo

The feed stock of copper fire refining processes consists of two major constituents: blister copper and high-Cu secondary scrap. A large fraction of this secondary scrap, originating from urban mining, is quite high in impurities such as Fe, Ni, Pb and Sn. Problems arise in electro-refining when these elements exceed certain limits. As a consequence, transformation of the secondary copper raw materials into high grade copper has become troublesome. However, the behavior of impurities relevant to fire refining conditions, essential for anode refineries, has not been studied in detail. Furthermore, limited research has been performed on the distribution of Ni between copper metal and slag. In this study, equilibration at 1300°C of liquid Cu-1wt.% Ni alloy and CaO-CuOx- FeOy-SiO2 slag in vacuum sealed quartz ampoules was performed for 12 hours, followed by water quenching. Electron Probe X-ray Microanalysis was employed to investigate the composition of the equilibrated alloy and slag. The distribution coefficients of Ni between slag and alloy were determined as a function of oxygen partial pressure and CaO concentration. INTRODUCTION Europe’s initiatives for a circular economy, pushing for resource-efficient ways for a sustainable future, puts Europe at the forefront of the globe. In Europe, 50% of the copper originates from recycling, being an excellent example of Europe’s circular economy (Juncker, 2018; Lacasse, 2018). High-grade copper recyclates are made available which regularly contain impurities like Fe, Ni, Sn and Pb. Aurubis Belgium is responsible for recycling these types of recyclates to anodes, cathodes and copper products. However, after fire refining of copper, the aforementioned impurities remain in the anode copper, leading to problems in electrorefining. During the fire refining of copper, a CaO-“Cu2O”-“Fe2O3”-SiO2 slag is used. Fundamental information of the distribution of impurities between the copper and this slag system is therefore essential to understand and improve the copper fire refining process at Aurubis Belgium.

Jan 1, 2019

By M. P. Brameld, R. H. McCorkell

"Overburden covering bedrock uranium deposits was sampled to depths of 29 m and Rn concentrations measured at the same depths. Total-alpha activities, V concentrations and Rn emanation (J) of the samples were measured. The U-flux into the overburden was greater in the past: oxidation and dissolution has since removed most U, leaving decay products which indicate the presence of U deposits when U itself does not. Distributions of U and decay products and their ratios to each other reflect U-migration and degrees of U-removal. Rn distribution in overburden is related to the J of overburden samples and the presence and movement of groundwater. Simple, rapid methods of total-alpha and J measurement are described.IntroductionThe overburden drilling apparatus developed by Bondar-Clegg and Company makes possible sampling and radon measurement in overburden from the surface down to about 50 metres. This apparatus was used here to study the diffusion of uranium and its decay products from ore deposits into over lying overburden at the N deposit of the Amok Ltd. property (Cluff Lake, Saskatchewan) and on the Imperial Minerals Ltd. property at Gooderham, Ontario. These ores are enclosed in bedrock; the overburdens were deposited by glaciers or streams. The migration of uranium and its decay products in such situations and the factors which affect it have been little studied in the past, as readily usable techniques for mapping it in three dimensions have not been available. The results reported here are somewhat sketchy and preliminary, but they indicate the value of the methods used and some of the patterns to be expected. Surface and subsurface sampling and measurements were carried out on 3-line grids crossing known zones of mineralization. The lines were 60 metres apart at Gooderham and 40 metres apart at Cluff Lake."

Jan 1, 1982

By den Bulck A. Van

In Europe, 50% of the copper originates from recycling. High-Cu containing scraps are regularly rich in impurities like Fe, Ni, Sn and Pb. Many high-Cu containing scraps are fed directly into anode-furnace casting installations or furnaces with limited refining capability. The impurities levels of the anodes produced in these processes should however remain acceptable for further electro-refining. The distribution of Sn between copper and slag has been investigated for conditions relevant to copper converting. Unlike previous studies, this work focuses on the behavior of Sn relevant to fire refining conditions, which are essential for anode refineries.In this study, liquid Cu–1Sn and CuOx–FeOy–SiO2 slag, with CaO additions, were equilibrated at 1300 °C in vacuum sealed SiO2 ampoules. After metal–slag equilibration, the samples were quenched in water. The composition of the slag and Cu metal was investigated with Electron Probe X-ray Microanalysis. The distribution coefficients of Sn between slag and Cu metal were determined as a function of slag composition.

By Henry S. Washington

I. INTRODUCTION. DURING the last twenty years or so the chemical investigation of rocks has made great advances, and it is now generally recognized that a knowledge of the chemical composition is as essential as that of the texture or mineral composition-if not more so-for the proper classification of rocks and study of their origin and relationships. Rock-analyses have vastly increased in numbers and, what is of greater importance, in quality. New and improved methods permit of greater accuracy than was possible in the early days, and the list of chemical constituents frequently determined has risen from the seven or eight of the greater part of the nineteenth century to twenty or more. Indeed, rock-analyses with determinations of so many constituents are now commonly made by the chemists of the United States and Australia, while in Germany, Great Britain, France, and Italy the rarer constituents are determined more frequently than formerly. As a consequence of this modern, accurate work, it has been discovered that some elements which were formerly supposed to be rare are of wide-spread occurrence and are often present in considerable amount. The fact is further being developed that the elements tend to show certain relations of occurrence or abundance in connection with each other. This is a fact which is applicable to the rarer elements, and which also finds a broad geological and petrological expression in the recognition of petrographic provinces. We are beginning to obtain some definite, though as yet rudimentary, knowledge of the distribution of the elements among igneous rocks. Some of the results along these lines obtained by study of the vast accumulation of analytical data now available are well known to petrologists, while others do not seem to be so gener-

Sep 1, 1908

By A. E. Back, K. E. Tame, W. F. Wyman, S. F. Ravitz

IN 1940, when it appeared that the United States soon might be cut off from foreign sources of high-grade manganese ore, the Bureau of Mines began an extensive series of investigations on the production of ferrgrade products from low-grade domestic ores by ore-dressing, pyrometallurgical, and hydrometallurgical methods. Among the hydrometallurgical processes for oxide ores investigated was a sulphur dioxide process in which the manganese was recovered from solution by precipitation with lime;1 this process is essentially as follows: The ground ore is suspended in water and leached with SO2 gas to extract the manganese as manganese sulphate. Calcium chloride is then added to the slurry to precipitate calcium sulphate and form manganous chloride solution, and the resultant slurry is filtered to remove the calcium sulphate together with the in- soluble portion of the ore. Calcium hydroxide is added to the filtrate and the mixture is agitated with air to precipitate hydrated oxides of manganese and regenerate calcium chloride. The precipitate is calcined, and the calcium chloride is recycled. To determine manganese extraction, reagent consumption, grade of product, and similar data for this process, a laboratory investigation was started. Two minor modifications in the process were soon made: (I) the ore was suspended in calcium chloride solution instead of in water in order to extract the manganese and precipitate the calcium sulphate in one step, and (2) the agitation with air after the addition of slaked lime to the filtrate was omitted because manganese hydroxide is readily precipitated without air agitation and can be nodulized or sintered to a satisfactory product. When the process was carried through a series of cyclic tests, it was noted that the concentration of dithionate ion (which is one of the products of oxidation of SO2 by MnOz) in the cycled solution gradually increased; at the same time the chloride content of the solution gradually decreased, owing to soluble losses in the leach residue and in the precipitate. After a number of cycles, the calcium chloride became virtually completely replaced by calcium dithionate, the quantity of dithionate ion formed during the leach being more than enough to make up for the losses of dithionate in filtering. The calcium chloride process thus developed into a calcium dithionate process. Since the latter eliminated the need for make-up calcium chloride, and the dithionate solutions appeared much less corrosive than the chloride solutions, work on the calcium chloride process was dropped in favor of the calcium dithionate process. ACKNOWLEDGMENTS The dithionate process was developed by the Bureau of Mines as part of a

Jan 1, 1946