Search Documents

By Carl C. Nesbitt

A study was conducted to investigate the claims of early observers who noted an increase in the rate of gold dissolution when chlorine was chemically produced in the leach vessel compared to sparging with chlorine gas. This "nascent" chlorine was presumed to be an active intermediate in the production of chlorine (C1,l from chloride ions. The study used UV light to produce an activated chlorine atom intended to recreate the observed increase in the gold dissolution rate. Although no change in the kinetic rate was observed, the reaction mechanism by which chlorine reacts with particulate gold was instead determined. Various concentrations of multivalent cationic chloride salts were added to the leach solution to demonstrate that the increased dissolution rate was due to the increased concentration of the chloride ion and ionic strength of the solution.

Jan 1, 1992

By J. W. Mahar, E. J. Cording

INTRODUCTION In exploration for rock tunnels, the geology should not only be described, but its effect on excavation and support assessed. It is not an easy task to correlate exploration results with support and excavation requirements, even when the exploration program is detailed and geologic conditions are relatively well known. Many of the significant geologic features are subtle and their effect is difficult to interpret from exploration results. However, in similar geologic settings, there are specific geologic features which will cause recurring support problems. Such features should be actively sought out when exploring in a given geologic setting. In blocky and seamy rock, the primary features controlling performance are the joints, shears, and shear zones. This paper describes the effect of such features on the formation and movement of rock wedges in tunnels driven in foliated metamorphic rocks in Washington, D. C. and New York City. In both areas the foliation commonly forms a N-S striking plane of weakness along which major shear zones, shears, and joints have formed. In addition, the structural history of the two areas has been similar, so that there are similarities in the orientation and character of the other major joint sets and shear zones in the rock mass. The observations were made in tunnels ranging from 10 to 70 ft in width and excavated at depths ranging from 80 to 800 ft. Most of the tunnels described were deep enough to be located in unweathered rock, or in rock only slightly weathered along joints and shears. Variations in the planarity, filling, spacing, and attitude of joints, shears, and shear zones accounted for significant differences in the

Jan 1, 1974

By C. F. Vos, J. D. Miller, J. C. Davidtz

"This work presents the potential for improving the flotation recovery of slow-floating sulphide minerals with the use of starvation dosages of a normal dodecyl (n-C12) trithiocarbonate (TTC) co-collector, together with a sodium isobutyl xanthate (SiBX) and dithiophosphate (DTP) collector mixture.At potentials below –150 mV (SHE), addition of nC12-TTC with SiBX improves the hydrophobicity of pyrrhotite, yielding captive bubble contact angles greater than those measured for SiBX or nC12-TTC alone, suggesting a low potential synergistic effect. This synergistic effect is further studied using Fourier transform infrared (FTIR) spectroscopy, the results indicating an increase in the surface concentration of the collector species when in a mixture. Thus, nC12-TTC with SiBX may act as an immobile surface anchor to which SiBX/SiBX2 molecules bond, increasing the localized concentration of collector species.Bench-scale flotation tests using mixtures of SiBX/DTP/nC12-TTC on a platinum group element (PGE)-bearing ore from the Bushveld Complex in South Africa confirm an improved metallurgical performance at very low substitutions (approx. 5 molar per cent) of SiBX. The improved recoveries for PGE, Cu, and Ni are correlated with improvements in the flotation kinetics of their slow-floating components. IntroductionShort-chain (less than C6) xanthates are very effective for the bulk flotation of sulphides (Fuerstenau, 1982), and early work (Leja, 1968; Gaudin, 1957; Plaksin and Bessonov, 1957; Taggart, Giudice, and Ziehl, 1934) indicated that the presence of oxygen in flotation slurries is necessary for the oxidation of the xanthate collector at the sulphide mineral surface to induce hydrophobicity. Fundamental research into the chemistry and adsorption mechanisms of xanthates over the years (Finkelstein and Poling, 1977; Woods, 1976; Winter and Woods, 1973) has revealed that for iron-bearing sulphide minerals, adsorption occurs predominantly through a charge transfer process. Oxidation of the adsorbed collector to the corresponding dimer takes place if the mixed potential of the system is greater than the reversible potential for dimer formation. In oxygenated slurries the rate of adsorption and oxidation of the collector depends greatly on the substrate surfaces. For chalcopyrite (Guler et al., 2005; Leppinen, 1990; Roos, Celis, and Sudrassono, 1990) and pentlandite (Hodgson and Agar, 1989) a two-step interaction with xanthate is proposed in which the chemisorbed xanthate is further oxidized to the dimer. The initial interaction of xanthate with pyrrhotite is through physisorption where xanthate physisorbs onto positive surface sites followed by oxidation to dixanthogen (Khan and Kellebek, 2004; Bozkurt, Xu, and Finch., 1998). This process is, however, slow and increased reaction time is needed to improve flotation recovery (Buswell and Nicol, 2002)."

Oct 1, 2018

A study of the effect of nickel on the cupellation process has shown that a very low "nickel limit" must be imposed for cupellation (0·08 grams nickel or 0·05 grams when copper is present). In the presence of slightly greater amounts of nickel, lead tends to spreadon the cupel with detachment of drops from the main lead pool. In crucible fusions nickel contaminates the lead button to a small extent, and this contamination is increased.in the presence of either iron or copper. Nickel also causes "shotting" of the lead, this effect being more apparent in the presence of iron.Both the spreading during cupellation and the shotting during crucible fusion are considered to be caused by adsorption of insoluble NiO at the Pb-PbO interface, lowering the interfacial tension.Excess litharge crucible charges are' fused at 116boC. to eliminate shotting. A brief· soaking in molten basic litharge slag effectively reduces the nickel content of lead buttons. The solubility of silver in litharge slags is considerably decreased in the presence of nickel. Corrections can be applied for silver losses in slags but these corrections are not as accurate as with copper ores.INTRODUCTIONThis paper on the effects of nickel on fire assays for silver is the second of an intended series describing investigations into the fire assaying method.In the first paper, discussing the effect of copper on fire assaying processes (Guerin, 1957), it was shown that certain elements, because of their relatively low affinities for oxygen, will tend to contaminate the lead button during crucible fusion and scorification. Nickel, having a slightly greater affinity for oxygen than has lead, would be expected to be oxidized and slagged readily, and would not be expected to appear in the metal phase (lead button) to any appreciable extent. Thus, judged solely on this basis of...

Jan 1, 1960

By E. Kordzadeh, M. Reza Bateni, M. Karaminezhaad, A. Moeini

A series of austenitic heat resistant Fe-Ni-Cr-Al alloys with different nickel contents have been investigated at 1100 ° C and 25, 50, 50,100 hours in S/0 bearing atmospheres. Before sulphidation test, the specimens were annealed in argon at 1250 °C for 8 hrs. Weight changes were measured using an automatic thermo gravimetric analyzer and corrosion products were analyzed by scanning electro microscope (SEM), energy dispersive X-ray spectrometry (EDAX), X-ray diffraction and optical microscope. The results showed that sulphidation resistance decreased with increasing nickel content. Internal sulphidation controlled by gaseous transport through cracks and pores and the formation of internal sulphide increased when liquid sulphides formed on the surface.

Jan 1, 2004

By D. G. Schmidt

Tests were conducted on C86200 high-strength yellow brass in order to ascertain the effect of a low level of nickel on the mechanical properties on this alloy. A series of two alloys was studied, one of which had a nickel content of 0.85% and the other with <0.05% nickel. Copper and aluminum content ranged from 62.5% to 64% and 3.2% to 4.6%, respectively. When compared by zinc equivalents, a nickel addition of 0.75% in high-strength yellow brass does not act like copper but raises the tensile strength, 0.5% yield strength and BHN while lowering the elongation.

Jan 1, 1999

By W. C. McClain

In the design of underground excavations, rock mechanics considerations are nearly always based on an elastic behavior of rock. Most rocks do exhibit a certain amount of elasticity, and the application of principles and concepts of elasticity to rock mechanics problems has been largely responsible for progress in the field over the past 10 or 15 years. No doubt the theory of elasticity will remain the most useful analytical tool available for both the design of underground openings and the interpretation of phenomenological data.

Jan 1, 1967

By Mingxia Liu, Hao Li, Qi Liu

"Laboratory batch flotation tests were carried out on fine (-20 µm) hematite to investigate the non-polar oil’s influences when sodium oleate, octyl hydroxamic acid, or oleyl hydroxamic acid were used as a collector. Batch flotation tests were performed with artificial mixed minerals (hematite:quartz = 1:1) under natural pH condition and kerosene was utilized as the model oil. The experimental results showed that kerosene emulsion behaved differently when used in conjunction with the three collectors. Kerosene helped improve the flotation when sodium oleate or oleyl hydroxamic acid was used as a collector. Nevertheless, it reduced concentrate weight yield, grade and recovery to a noticeable extent when octyl hydroxamic acid was used as a collector, especially at low dosages. In addition, single hematite batch flotation kinetics tests coupled with water recovery measurement were carried out to study the role of kerosene at different collector dosages. It was observed that water drainage and the resulting froth destabilization by kerosene was dominant at low collector dosages, especially in the flotation using octyl hydroxamic acid. At higher collector dosages, the water drainage and froth destabilization effect by kerosene was possibly counter-balanced by the higher hematite hydrophobicity and bubble surface tension gradient, which led to more stable froth layer.INTRODUCTION The minerals industry is facing a steady decline in ore grade, compounded by increasing complexity of mineral dissemination. As a result, the ore has to be ground sufficiently fine to have a suitable degree of mineral liberation, which produces large percentages of fine and ultrafine particles outside of optimal size range for ore dressing. Due to the unique characteristics of fine particles, i.e., small mass, high specific surface area, and problems such as increased solubility of complex minerals (Finkelstein, 1997; Finkelstein & Allison, 1976; Fornasiero & Ralston, 2005), high reagent consumption, fast surface oxidation in the case of sulfides (Collins & Read, 1971; Klassen & Mokrousov, 1963), severe particle entrainment (Subrahmanyam & Forssberg, 1988; Warren, 1984), low flotation rates (Glembotsky, 1953; Philippoff, 1952; Ye & Miller, 1988), slime coating (T. K. Mitchell et al., 2005; Parsonage, 1984), etc., flotation performance of these finely ground ores is very poor in terms of low concentrate grade and recovery."

Jan 1, 2017

By R. Altındag, D. Akbay

The point load index is a simple, fast, and inexpensive method for determining rock strength and can be applied both in the field and in the laboratory. There are, however, some disadvantages and limitations to the method, and the test results can be affected by the person carrying out the test, the rock characteristics, or the test device. In this study we describe an investigation into how the point load index value is affected by the shape of the conical platens used in the test. Point load index tests were carried out using different devices fitted with conical platens of different spherical radii, and on a modified device which circumvented the limitations/disadvantages. It was seen that the point load index value increased as the platen radius increased, as expected. In the case of testing using non-standard conical platens, an equation is proposed to normalize the point load index value with respect to the standard spherical radius value.

Nov 1, 2021

"The global demand for the copper metal is continuously increasing however, the high-grade copper ore deposits are constantly depleting. As a result, ore bodies with complex mineralogy characteristics and rich in arsenic-copper bearing minerals are increasingly processed. Arsenic-copper sulphides such as enargite can represent a significant amount of arsenic in concentrate, which causes high financial penalties by smelters. On the other hand, arsenic (As) is a highly toxic inorganic pollutant, which causes human health and environmental problems. Recent research studies have demonstrated promising results showing the possibility of separating arsenic-copper sulphides from copper sulphides using controlled pulp potential (Eh) flotation at laboratory scale. However, the selective removal of arsenic-copper minerals in real ore systems is not well understood. Two ore samples were selected from the Tampakan copper-gold deposit located in the Philippines named the HAS (high arsenic sample) and the LAS (low arsenic sample) samples and the mineralogical analyses were performed on both samples. The floatability of enargite in a batch flotation system under controlled pulp potential conditions was investigated for the HAS and the LAS samples. It was observed that it is possible to selectively separate enargite from other copper minerals after reducing the pulp potential to about -200 mV SHE at pH 11 in the LAS sample. However, no separation between enargite and other copper minerals was observed at a reducing potential for the HAS sample. Mineralogical analyses and surface chemistry studies were undertaken for both samples to find out the reasons for different observations. This study has an important implication in sulphide flotation to achieve sustainable development in the utilisation of arsenic-copper mineral resources. INTRODUCTIONAs the demand for copper is increasing, the extraction and development of resources including complex deposits is becoming necessary. These complex deposits often have issues such as: lower grade ores, floatable non-sulphide gangue, very fine-grained ore and therefore poor liberation and significant regrinding, mixed copper mineralogy, complicated galvanic interactions, economic levels of gold and silver, and high levels of impurities such as arsenic. There is currently no established methodology for separating arsenic-bearing copper minerals from other copper sulphide minerals by flotation. The possibility of separating arsenic-copper sulphides from other copper minerals by controlling the potential of the flotation pulp has been shown in previous studies. However most of these studies were conducted on single mineral systems and the selective removal of arsenic-copper minerals in complex ore systems is not well understood. The flotation behaviour of arsenic-bearing minerals within complex ores differs significantly from that of pure mineral systems due to the effects of mineralogical composition, the degree of liberation, and the surface oxidation. The understanding and manipulation of these effects can lead to improvements in the selective flotation recovery of arsenic-bearing species from complex ore systems."

Jan 1, 2018

By W. C. McClain

In the design of underground excavations, rock mechanics considerations are nearly always based on an elastic behavior of rock. Most rocks do exhibit a certain amount of elasticity, and the application of principles and concepts of elasticity to rock mechanics problems has been largely responsible for progress in the field over the past 10 or 15 years. NO doubt the theory of elasticity will remain the most useful analytical tool available for both the design of underground openings and the interpretation of phenomenological data. Dr. Cook&apos;s analysis of rock behavior based on energy considerations represents a significant new approach to mining rock mechanics problems. Although the foundations of this analysis are somewhat broader and more general than elastic analysis, the development and applications are grounded almost entirely in the theory of elasticity. It has long been known1,2 that all rocks, even granites and dense limestones, exhibit nonlinear time-dependent strain properties to a greater or lesser degree. Creep strain (that is, deformation under constant stress) in salt, potash, and trona can be several orders of magnitude greater than instantaneous elastic strain. Design of underground workings in these materials must incorporate provisions for these strains and must therefore go considerably beyond elastic analysis. Some of the principles of underground design in highly plastic materials will be discussed in this paper. Since all rocks, especially when highly fractured, exhibit a certain amount of creep-type strain, these concepts should be at least recognized in any rock mechanics problem. The discussion will be illustrated largely, but not entirely, by examples drawn from

Jan 1, 1967

By Tadashi Nishida

Subsidence due to mining caused various kinds of damage to the surface structures, and actually great deal of mining damage becomes the severe social problem at some time in many coal fields, but the most of mining damage was restored at present. Recently, the effect of old coal working on the deformation of newly constructed structures has become into question, because it was obliged to plan many engineering structures in old mining areas for the shortage of adequate construction sites and the difficulty of getting location. That is, building, dams, bridges for railroads and highway, power plants, tunnels, storage tanks and so, have to be built on the ground which has old coal working.

Jan 1, 1982

By L. C. Woollacott, A. K. Tripathy, J. H. Potgieter

This paper presents the second of a two part study on density stratification in a laboratory batch jig. The first study, reported elsewhere, investigated the effect of operating conditions on the stratification profile achieved at equilibrium. The study reported in this paper investigated their effect on the kinetics of density stratification under 18 different sets of operating conditions - five for binary systems with different particle densities; and 13 for a ternary system with different configurations of the jig cycle. Although the study was academic in nature (it involved simple systems of 8 mm glass beads) it has a number of practical implications. It found that the most influential operating variables affecting stratification kinetics are the amplitude of water displacement, the pulsion hold time, and, to a lesser extent, the pulsion time. It also found that reasonable rates of stratification can be expected in systems with density differences as low as 237 kg/m3 but below this the kinetics deteriorate significantly. The two studies together suggest that, within a broad range of operating conditions, the equilibrium stratification profile is independent of control variables and it is the control of stratification kinetics that has the primary influence on the quality of density separations in a jig. Keywords: Jigging kinetics, stratification, equilibrium stratification, batch jig

Jan 1, 2020

By Zhang Chuanfu, Li Shixiong

"In the electrolysis electrodeposition or electroplating of aqueous solution of copper, lead, zinc, nickel, manganese etc, with the increase in cathodic over potential the reducing rate of metal and the cathodic current efficiency increases and the deposit becomes more compact and smooth. According to this principle, a method and equipment of the auto-control of electrolyte quality is invented. The industrial application shows that this method turns the experienced operation into auto-control. The quality and quantity of metal is improved greatly and the consumption of electric energy is reduced.In the electrolysis, electrodeposition or electroplating of aqueous solution of copper, lead, zinc, nickel, manganese etc, usually organic additives are added according to the state of cathodic deposit according to experience. This traditional and experienced operation, often lead to that the quality of additive is not optimum which affects the quality and quantity of metal and increases the consumption of electric energy. To counter the controlling problem of the quantity of additive, the authors have invented a corresponding equipment of the auto-control of electrolyte quality [1], it has found application in industrial practice."

Jan 1, 2000

By K. Knuutila

The behaviour of thiourea, animal glue and chloride ions in the electro¬lysis of copper has been investigated by various different electrochemical experiments, i.e. polarization curves with stationary copper electrodes, long-time galvanostatic electrolyses and Hull cell experiments. Polarization curves with stationary copper electrodes show that animal glue has a polarizative effect on the deposition potential. Small thiourea contents affect depolarizatively when high concentrations retard the copper deposition. The microstructures of the deposited copper after the long-time electrolyses show that animal glue favours a basis oriented deposition structure. With thiourea the field orientated structure was evident. It was also observed that the deposited structure depended much on the grain structure of the starter sheet. The chloride ion concentration has a drastic effect on. the crystal size of the deposited copper as it was found out in Hull cell tests. Chloride ions flattened the the crystals and the deposition became smoother when the chloride ions were added. The cathode copper quality is discussed according to the literature. Special attention is paid on the codeposition of thiourea and the origin of sulphur impurities in copper cathodes.

Jan 1, 1987

By S. W. Jacobsz, E. P. Kearsley, N. K. Schoeman

A physical modelling approach was adopted to simulate the process of cave mining propagation at various horizontal to vertical stress state ratios, and image data was captured and used to characterize the resulting failure mechanisms. Image processing was integrated into the study to determine minor principal strains in models to identify where critical extensional strains had been exceeded relative to crack propagation. The study exhibited a scale factor magnitude of 119 using a calculated critical extensional strain value of 0.014% for the modelling material used. It was perceived that cave propagation occurred through successive parallel extensional ‘fracture bands’ in all cases, as noticed in models of prior studies, deviating from that described by the Duplancic model. Cracks tended to bisect regions of minor principal strain equal to the critical extensional strain, which suggests ‘fracture banding’ is an acceptable failure mode for brittle, rock-like materials. Moreover, it was found that models with lower horizontal to vertical stress ratios (K ratios) showed a greater degree of vertical development of the caving mechanism (at similar vertical stresses), while the vertical extent of the cave was suppressed in models with higher K ratios. Models subjected to larger vertical stresses experienced slower cave formation in latter time-steps. These models exhibited larger two-dimensional caved perimeters and areas, respectively.

Nov 30, 2022

By Peter Zhang, Daniel Su, Berk Tulu, Bo Hyun Kim, Zoheir Khademian

Over 2,000 shale gas wells have been drilled in the Pittsburgh Seam longwall reserves. As longwall panels are laid out, some of these shale gas wells must be located in longwall chain pillars. With longwall mining on both sides and the constraint of chain pillar size, gas well in chain pillars are subjected to longwall-induced ground movements and stresses, which could induce deformations in gas well casings Casing deformations are associated with several factors such as overburden geology, surface topography, setback distance, and casing construction. Overburden geology is one important factor that largely determines the locations and levels of deformations in gas well casings Previous NIOSH gas well research has found that casing deformations above the coal seam horizon are smaller under deep cover than unde shallow cover and that casing deformations could occur at the coal seam horizon under deep cover. Recent mine-by cases have provided more insights into the locations and amount of longwall-induced casing deformations as well as the potential occurrence of a large casing deformation at the coal seam horizon. This paper presents three recent mine-by cases with shale gas wells in the chain pillars between two adjacent longwall panels under different overburden depths. Casing deformations were measured by multi-finger caliper surveys and predicted with numerical modeling. With the established numerical model, the effect of overburden depth was further analyzed to investigate the potential occurrence of a large casing deformation at the coal seam horizon under deep cover. These mine-by cases not only provide a general demonstration of how overburden depths can affect longwall-induced stresses and deformations but also give a good indication about the level of casing deformations that could occur under different overburden depths. The study concludes that (1) casing deformations reduce with increase of overburden depths at the gas well; (2) a cementing alternative with production casing uncemented is an effective means to eliminate production casing deformations; and (3) large plastic casing deformation could occur in the production casing at the coat seam horizon under deep cover. The experience and knowledge gained from these mine-by cases would help longwall operators and gaza companies to take appropriate measures to minimize the influence of longwall mining in shale gas wells in chain pillars.

Jun 25, 2024

By D. G. Kotlyar

Oxidized sulfide minerals, commonly formed by weathering, increasingly are becoming important resources as primary sulfide deposits are depleted. Oxidation, in general, reduces selectivity and recovery in flotation. The objective of this research was to determine the mechanisms of oxidation and collector adsorption in sulfide systems as a step towards developing improved technologies for beneficiation of oxidized sulfides. Data from microcell flotation tests are combined with electrochemical and spectrophotometric measurements. The adsorption of ethyl xanthate (EX) on oxidized sulfides was characterized using AC impedance techniques and correlated to flotation response. The floatability of chalcocite, chalcopyrite and pyrite was dependent on the extent of oxidation. Oxidation for 1?) d at 65? C inhibited flotation of chalcocite, and chalcopyrite even after the addition of a large amount (1 x 10&apos;) M) of collector. Heavily oxidized (27 d) chalcocite remained unfloatable. However, longer oxidation of pyrite and chalcopyrite restored the floatability. Oxidation resulted in an electrically resistive, nonporous surface layer.

Jan 1, 1993

By G. White

Traditional atmospheres used for Aluminum annealing have been air, exothermic gas, and cryogenic purity Nitrogen. Air and exothermic gas have several problems associated with them such as surface discoloration, toxic emissions, and explosion hazards. High Oxygen levels can cause Magnesium streaking and oil staining, and therefore pure Nitrogen has been the atmosphere of choice for high quality Aluminum coils. A comparative study was made on key Aluminum alloys annealed in Nitrogen with different Oxygen concentrations to determine the effect on surface quality. The atmosphere composition inside the furnace was analyzed during the purge and heat cycle to determine its effects on purge times and exhaust emissions. The Aluminum coils after annealing were visually inspected for surface staining before and after rolling. The lab study revealed that Nitrogen with up to 1.0% Oxygen is acceptable, and did not adversely effects the surface quality or any of the other processing variables. However it isbelieved that higher Oxygen concentrations are acceptable depending on the rolling oils and alloy systems.

Jan 1, 1996

By David White

This paper is the result of a comparative study of ultimate coal analyses made and published by the United States Geological Survey. This study, at first casually undertaken to devise an acceptable classification of coals based on chemical analyses, was continued in connection with a microscopic examination of a number of the coals. The initial comparisons, made from a relatively small number of analyses, not only confirmed a previous conviction that the elimination of oxygen incident to the development of a coal is economically far more important than has been generally suspected, but also showed that oxygen is very nearly as harmful as ash in coal. The immediate purposes of the present study were: (a) To determine more definitely, from a comparative examination of a large number of ultimate analyses, the relative importance of oxygen as an impurity in various coals; (b) to illustrate the transition between various grades of coal of similar origin-transition mainly due to progressive devolatilization, brought about more or less directly by dynamic influences; (c) to ascertain the relative proportions of oxygen, hydrogen, and carbon in coking coals, especially with reference to a theory tentatively framed to explain the coking quality; and (d) to forecast the probabilities of successfully treating a large number of coals so as to render them amenable, in a softened condition, to satisfactory study under the microscope.

Jan 1, 1911