Search Documents

By Alfred E. Hunt

The charge to be described was made in a seven-ton furnace, with a hearth twelve feet long and eight feet wide, with three gas and three air ports on each side. The stock of the entire heat was charged cold in one hour and five minutes, a part of the pig being first placed upon the bottom to protect it, then upon it the plate-scrap and blooms, and finally the remainder of the pig—some two thousand pounds. In fire hours and twenty-five minutes after beginning the charge the metal was melted down level, and two hundred pounds of hot twelve-per cent. spiegel was charged, care being taken to have it entirely immersed in the bath. In two hours more the bath was thoroughly melted and hot, and began to boil, i. e., the carbon began to be oxidized and evolved through the bath of covering slag as carbonic acid and carbonic oxide gases. Seventy-five pounds of lumps of Republic specular iron ore were added at this time, increasing the action, so that in ten minutes after the metal was in active ebullition. A test of the metal showed it to have about 0.90 per cent. carbon. One hour after the first ore was added a test was again taken, after thorough rabbling of the metal, and it was found to be 0.37 per cent. carbon. One hundred pounds more of lump Republic ore and about seventy-five pounds of limestone were then added, and fifty minutes later, after the bath was thoroughly rabbled, a -test showed the metal to have 0.23 per cent. carbon. Twenty-five pounds more of Republic iron ore were added and the metal allowed to boil for twenty minutes, when a test, after rabbling, showed the carbon to be 0.18 per cent. and the manganese to be 0.01 per cent.; the slag fracture was vitreous and of a very dark-green color. About forty pounds of limestone were added, and, the metal being hot and in a state of quiet ebullition, a hickory pole of twelve feet length and about four inches diameter, was run through the aperture in the centre door and held in a steady inclined position in the bath, with the end touching the bottom, the pole being shoved in further as it was burned away. The bath was carefully watched to see that the action that ensued was not too violent, the pole being several times

Jan 1, 1884

By Alfred E. Hunt

Professor EGGERTZ first published a method based upon the fact that, when steel is dissolved in dilute nitric acid, and heated until the separated flocculent carbonaceous matter goes into the solution, the liquid assomed a brown color proportionate in intensity to the amount of the combined carbon in the steel. This method has been so variously modified that at present but few chemists use exactly the same procedure. It is the object of this paper to present

Jan 1, 1884

By L. P. Meade

The need to feed an established talc mill from a crude are source located closer to the mill prompted the drilling in 1986 of a previously mapped talc-carbonate deposit. This talc-bearing rock had never been considered as a potential source of crude talc are because of the high carbonate content and other deleterious minerals that were observed in outcrops. Selective mining, in-pit grade control and creative processing has allowed this deposit to be developed into an orebody. By definition, an orebody has to be a source of positive cash flow. With industrial minerals, this is determined as much by market acceptance as by are tenor.

Jan 1, 1992

By P. Walshe

A common belief among Itlnl.ng operators today is that computer based truck m:mitoring and dispatching systems are only applicable to, or affordable by, very large scale open pit mines. Before the advent of microcomputer technology this belief was generally a valid one. Microcomputer technology as it currently exists has reached a high level of sophistication and capability, rapidly approaching that of the minicomputer standard. When coupled with reliable software and data communications packages, it now provides the means to make truck monitoring and dispatching a viable and attractive management aid to mines of all sizes. This paper briefly addresses the evolution and current state of computer truck dispatching and examines a microcomputer based system in this context. To demonstrate the effectiveness of this approach to truck dispatching a recent installation in a medium sized mine is presented. Preliminary field data from the case mine are presented to illustrate the methodology.

Jan 1, 1989

By Edward R. Mueller

As an alternative to a million dollar, sensor based, computer dispatching system, Cyprus Pima Mining Company has installed a home¬made analog computer. The device is used in conjunction with a standard radio-dispatching system; it is inexpensive and very simple to build and operate. It enables the dispatcher to make near opti¬mum dispatching decisions and to identify all off schedule haulage trucks. Since installation, Cyprus Pima has experienced significant increases in pit productivity.

Jan 1, 1977

By Yashar Pourrahimian, Roberto Noriega

Truck fleet dispatching plays a crucial role in reducing operational costs and fulfilling operational targets in open-pit mining operations and is subject to large uncertainty arising from the operating cycles of trucks and loading equipment. This paper proposes a reinforcement learning-based truck dispatching system. Reinforcement learning is a machine learning area that deals with learning an optimal sequential decision-making strategy in an uncertain environment. An open-pit load-and-haul simulation is developed that also captures the truck movements and interactions in the shared road network, and a Neural Network is successfully trained to suggest truck dispatching decisions in a real-time manner.

Jun 25, 2023

Aitik, a Boliden owned and operated open pit mine located in northern Sweden, will expand production from 18 Mt per year today to 36 Mt per year copper ore during 2010. The challenge for the mine operation is to double production with a planned increase of the shovel and truck fleet of only 50 per cent. This will be achieved through improved shovel and truck utilisation and productivity. In early 2005 Aitik started projects to enhance the utilisation of truck engine hours and to reduce fuel consumption. Both projects were successful, within a year efficient2 utilisation of engine hours increased from 60 per cent to 75 per cent and fuel consumption was reduced by six to eight per cent. The truck utilisation project focused on minimising idle truck hours by for example four operators on three trucks thus reducing idle engine hours to minimise lost time for breaks and shift changes. Other measures included focusing on improved dispatch usage, parking trucks when overtrucked, etc. Eco-driving was a project together with Swedish Road Administration with the objective to combine economical and environmental savings. To keep the focus on eco-driving a reward was set up for the shift team with the lowest fuel rate over rolling 15 weeks periods. Both activities included a comprehensive training program for mine foremen, dispatchers and truck operators focusing on efficient use of trucks from economic driving to optimised truck dispatching and minimising idle engine hours. Online monitoring of trucks activities and fuel consumption combined with continuous reporting gave shift foremen and management a tool to discuss and follow trends and individual shift team performance. The combination of close monitoring of mainly organisational practices and operator training resulted in significant productivity increase and lower operating costs without any capital investments.

Jan 1, 2007

A brief history of the significant haulage truck feature changes and the factors that influenced those changes during the 60's and 70's provide a basis for forecasting the changes that can be expected in the 1980's. A review of the impact factors and changing requirements that currently exist that will create changes. Define the critical requirements of a successful haulage truck design and discuss the availability of bigger engines and better electric drive componetry to provide deeper pit capability and improve reliability. The Unit Rig Trolley Assist System to provide improved productivity and diesel fuel savings and an economic analysis to evaluate the Trolley System is covered. The Unit Rig Automatic Truck System for a driverless truck is covered in concept and discussed from the point of view of the experience in a test in a New Mexico mine. INTRODUCTION A good basis for trying to forecast what is going to happen in the future is to go back a little bit in history, to see what the influencing elements were in different periods of time as a foundation for the forecast. INFLUENTIAL FACTORS IN THE 1960'S If you look at the truck development that occurred in the 1960's, there were some identifiable factors that give us insight. (See Fig. 1) Several things happened at the beginning of the 1960's. Mechanical drive haulage trucks were introduced that were

Jan 1, 1982

By S P. Young, K R. Monro

Reducing metal prices have forced mining operations to become more efficient and innovate in order to do more with the existing base. Much of this effort has focused on improving the efficiency of load and haul operations. The key to this is to understand and quantify where delays and missed opportunities exist. Metrics such as utilisation of availability, efficiency utilisation and asset availability are helpful indicators of performance; however, uptime-based time usage models and performance analysis tools using productive operating time models help to identify additional improvement opportunities.Phu Kham is a copper-gold mine operated in the Lao People’s Democratic Republic (Laos) since 2008 by PanAust Limited. The mine is a single large open pit of 450 m depth, running a fleet of 51 100 t class rigid dump trucks and 300 t and 200 t shovels controlled with the aid of a fleet management system in order to achieve ex-pit material movements of 56 Mt/a.Commencing in late 2014, a range of initiatives were implemented in order to improve the efficiency of the mine haulage fleet. These include hot seating of all operator changeouts via changeout ramps, split shifting of crews to minimise queuing delays, maximising blast volumes and minimising blast event days to reduce blast exclusion delay events including opportune refuelling of equipment during blasting events, inspections of trucks during refuelling events, implementation of a dedicated haul road services team to help reduce wet weather related delays and infrastructure development for haul path efficiency improvements.These and other initiatives have allowed the mine haulage fleet utilisation of availability (UofA) to be sustainably increased from 85 per cent to 97 per cent (see Figure 1), efficiency utilisation to increase from 85 per cent to 90 per cent, and productive operating time (POT) to increase from 73 per cent to 84 per cent. The corresponding increases in efficiency of the haulage fleet has allowed an equivalent reduction of eight haul trucks from the fleet to meet continuing life-of-mine production requirements.CITATION:Monro, K R and Young, S P, 2016. Truck haulage improvements at the Phu Kham mine – the journey to 97 per cent utilisation of availability, in Proceedings International Mine Management Conference, pp 339-346 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 22, 2016

By David M. Lake

Conversion to trolley assist is a means of minimizing diesel fuel consumption, which in many mining situations offers a rapid payback of capital investment plus the inherent flexibility and maneuverability of truck shovel operation. When diesel electric truck shovel mining operation with trolley assist is compared to alternative mining methods such as conveyor systems, the trolley assist system can be easily justified in terms of return on investment, payback and increased productivity. A review of present technology, performance requirements and past experience in the mining industry has led to the development of a trolley assist system for diesel electric haulage trucks which, is proven in the mining environment, offers significant reduction in fuel consumption and increased productivity.

Jan 1, 1981

By C. O. Aksoy, H. Kose, K. Ozfirat, T. Malli, A. Gonen, S. Gurgen

In selecting mobile mining equipment, factors including availability, useful economic life, maintenance and operating costs, and spare parts availability are considered. Given these factors, trucks and shovels with different capacities are selected. Optimizing equipment for pit and hillside quarry cases, where 8% and 10% ramps are commonly in use, were examined; the effect of other mining activities such as drilling and blasting on unit cost were considered. In principle, 20 m to 25 m high benches should be economical for downhill haulage, and 7 m to 10 m low benches economical for uphill haulage. However, practice of both mining styles favours 10 m to 15 m bench heights. Hence, the analysis here was carried out with the field experience bench height range. In the study, a truck-shovel optimization was based on the movement of 5 to 20 million cubic metres (in 2.5 million cubic metre increments) of overburden stripping at the Eynez open pit mine in the Soma region of Turkey. The outcome showed that low-capacity shovels were unfavourable due to high production expectations. High-capacity shovels were also unfavourable due to health and safety issues causing high instances of impact vibration on trucks during the loading cycle and a decrease in foreseeable unit lifetimes. The number of shovel passes required to load a truck ranged from three to six. Trucks with high-capacity bodies were deemed uneconomical due to high investment and operating costs.

Jan 1, 2005

By Y. Lizotte

The purpose of this paper is to describe a stochastic simulation program used to assess several dispatching rules applicable to small scale computerized systems for optimizing truck/shovel productivity. The system studied is semi-automated with a dispatcher communicating instructions by two-way radio. The simulation program is structured on an advance clock approach which enables the insertion of dispatching rules at various points in the haulage net- work. The rules tested include minimize shovel idle time, maximizing immediate truck use and assigning trucks to shovels to meet specific production objectives. A variation of the traditional "Match Factor" is implemented to maintain fleet balance throughout the shift. A mine case study demonstrates how the dispatching rules increase productivity of such semi-automated dispatching systems. Practical problems involved in the implementation of small computerized dispatching systems are also discussed.

Jan 1, 1986

For the past 40 years, underground trucking using diesel powered or electric wheel driven vehicles, either conversions of surface trucks, or purpose built, has been the preferred means of ore and waste transport in underground mining. The relatively low capital cost, flexibility and requirement for minimal infrastructure means that trucking systems are selected in the early stages of a mining operation. An increase in the carrying capacity of trucking systems with dimensions to operate within existing development excavations is the solution to long term ore and waste underground haulage systems using trucks. The next generation of underground trucks will be low profile articulated trucks with carrying capacities up to 60 t.

Jan 1, 1998

By R B. Venugopal, P Staples

The selection of the mode of transport for moving bulk materials is never a simple task as there are various concerns/considerations applied to the selection of the most practical and cost-effective mode of transport to be used to move bulk materials. This paper examines various alternatives for moving ore from a mine at the top of a mountain to a process plant below (some 5000 m apart and a vertical drop of 650 m). The terrain of the mountain section of the route has added its own specific requirements, resulting in the final selection of a pipe conveyor for this application. The paper further addresses the final selection of hardware used in the implementation of the solution.

Jan 1, 2005

By S. Andika, O. A. Putri

Maintaining fleet productivity, which consists of balancing loader and truck performance, has always been a challenging task. An automatic dispatching system (ADS) is implemented to help monitoring fleet condition and assign trucks to a designated loader. Integrated data from real time Global Positioning System, Vehicle Health Monitoring System, and other production related data are acquired to support the ADS. However, the abnormal truck cycle has been the main culprit which resulted in unnecessary loader hanging time and trucks queuing time. Hanging and queuing time accounted for 2.34 and 2.07 minutes respectively per loading cycle or equal to 2,861 loose cubic metres per fleet per day production losses. Using integrated dispatching system data, the authors conducted research to study a truck’s hauling cycle that affects fleet productivity. The data is modelled to obtain the arrival rate pattern in a front loading area by adopting the queue theory algorithm. This paper aims to understand the potential pattern of a truck’s cycle abnormality and to resolve its occurrence.

Sep 1, 2021

By G J. Halstead, R C. Steinhaus

The True Pipe® in-line sampler was developed in an attempt to address the need for a mechanically reliable and correctly designed sampler to suit one-dimensional pressurised slurry pipelines, often found in metallurgical process plants but for which no reliable and representative sampling solution as yet exists.The design, whose operation is based on the principle of symmetry, is described by Dominique François-Bongarçon (2005) with the synchronous opening and closing of relevant valves. It representatively isolates portions of the particulate material stream at predetermined intervals for effective extraction of primary increments for subsequent sample compositing.Theory of Sampling applicable solutions have proven elusive in flowing pressurised particulate material streams, with various attempts to date not having formulated a viable, mechanically reliable and acceptable design.Compliance to sampling theory is critical, and a number of tests were conducted where certain operating parameters were altered to determine their influence and sensitivity on sampling representativeness.The results of the initial series of tests performed on a carefully designed rig are presented, with additional work discussed for necessary investigation in the near future.Getting closer to a robust, economic and correct design for this challenging application in the minerals industry may now not be that far away. Plant management staff will see improved metallurgical mineral balances around their process plants and significantly reduced sampling discrepancies, particularly in tailings applications. Improved quality control is now possible where, due to plant head room constraints, classical cross stream sampling methods cannot be employed.CITATION:Steinhaus, R C and Halstead, G J, 2014. True pipe sampler – a correct design utilising the principle of symmetry in pressurised slurry particulate streams, in Proceedings Sampling 2014 , pp 127–134 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 29, 2014

By L. E. Welch, C. W. MacGregor

THE past 20 years has seen a revolutionary change in the testing of materials at elevated temperatures. This has largely been brought about by the practical importance of the creep problem in the design of equipment for operation at high temperatures. The short-time tension test carried out at elevated temperatures has consequently assumed in many cases only a secondary role compared to the long-time creep test. In many problems, however, a knowledge of the short-time high-temperature properties of a metal is essential. To mention a few cases in which this is so, we might include all hot-forming operations such as rolling, forging, etc., the welding problem if residual stresses are to be computed, the development of new alloys for high-temperature service where, in the initial stages, time does not permit of long duration creep tests, and others. Usually a knowledge of the short-time properties is desired, if only to serve as a background against which to compare creep behavior. In conducting short-time high-temperature tests, it has been almost the universal practice to determine stresses based on the original area and strains referred to the original gauge length which is usually chosen as 2 in. It has been pointed out 1,2 that one of the reasons that the true significance of certain tensile properties is not understood, which perhaps curtails their usefulness, especially when the material is applied [ ] under conditions differing considerably from the test conditions, is that true physical stresses and strains are not determined. It is essential to have a knowledge of true stresses and strains in order to correlate the values present in the tension test with those existing, for example, in hot metal-forming operations and in the general problem of the yielding and failure of metals under combined stress conditions. Stress and strain values based on the original dimensions of the test piece do not exist physically except in the early stages of the test. Since at the present time there is very little information in the literature on true stress-strain relations in the short-time high-temperature tension test it is proposed in the following pages to describe a

Jan 1, 1942

By L. E. Welch, C. W. MacGregor

THE past 20 years has seen a revolutionary change in the testing of materials at elevated temperatures. This has largely been brought about by the practical importance of the creep problem in the design of equipment for operation at high temperatures. The short-time tension test carried out at elevated temperatures has consequently assumed in many cases only a secondary role compared to the long-time creep test. In many problems, however, a knowledge of the short-time high-temperature properties of a metal is essential. To mention a few cases in which this is so, we might include all hot-forming operations such as rolling,' forging, etc., the welding problem if residual stresses are to be computed, the development of new alloys for high-temperature service where, in the initial stages, time does not permit of long duration creep tests, and others. Usually a knowledge of the short-time properties is desired, if only to serve as a background against which to compare creep behavior. In conducting short-time high-temperature tests, it has been almost the universal practice to determine stresses based on the original area and strains referred to the original gauge length which is usually chosen as 2 in. It has. been pointed out 1,2 that one of the reasons that the true significance of certain tensile properties is not understood, which perhaps curtails their usefulness, especially when the material is applied [ ] under conditions differing considerably from the test conditions, is that true physical stresses and strains are not determined. It is essential to have a knowledge of true stresses, and strains in order to correlate the values present in the tension test with those existing, for example, in hot metal-forming operations and in the general problem of the yielding and failure of metals under combined stress conditions. Stress and strain values based on the original dimensions of the test piece do not exist physically except in the early stages of the test. Since at the present time there is very little information in the literature on true stress-strain relations in the short-time high-temperature tension test it is proposed in the following pages to describe a

Jan 1, 1942

"Standing 92 stories high and just over 1,362 ft tall, Chicago’s Trump International Hotel and Tower is perfectly positioned at the center of one of the world’s most impressive skylines.The Tower serves as a link between its famous predecessors, Willis Tower (formerly, the Sears Tower) to the south and the John Hancock Building to the north. Originally planned to be the world’s tallest building, the project was scaled back when the developers started questioning the need for super-tall buildings after the September 11, 2001 terrorist attacks. In its River North neighborhood, Trump Tower dominates the skyline as a symbol of Chicago’s last great building boom, standing triumphantly over other high-profile projects that have been postponed due to current economic realities.It is often said that the three most important factors in real estate are location, location and location. This maxim was not forgotten by The Trump Organization when the site was selected for the International Hotel and Tower. Located two blocks west of Michigan Avenue and Chicago’s famed Magnificent Mile, the site is bound by the historic Wrigley Building to the east, Wabash Avenue to the north and west, and the Chicago River to the south. The building’s position along a bend in the Chicago River allows visitors and residents unobstructed views to the mouth of the Chicago River and Lake Michigan. Site ChallengesUnderneath the site there are approximately 10 to 20 ft of sand and urban fill underlain by soft Chicago blue clay. At 75 ft in depth, the soft clay transitions into Chicago hardpan, a very hard till that was consolidated by the glaciers over 10,000 years ago. Below the hardpan, the till turns granular with cobbles, boulders and water under pressure. Bedrock is about 100 ft below existing grade and has a weathered surface with fractures and clay seams. Unweathered limestone bedrock is sound and hard with unconfined compressive strengths of 10,000 to 20,000 psi."

Jan 1, 2009

By Sean Gallagher

Study Design. A split-plot experimental design was used to evaluate the influence of posture, trunk angle, and rotational velocity on peak torque output and myoelectric activity during maximal trunk extension maneuvers. Objectives. To determine whether the kneeling posture alters extension torque capabilities in isometric and isokinetic exercises as compared with standing. Also, to ascertain whether recruitment of trunk muscles is modified by such a postural change. Summary of Background Data. Factors such as workplace geometry may force workers to adopt awkward or unusual postures in the performance of manual tasks. An understanding of the limitations placed on strength in unconventional working postures is crucial to the proper design of jobs. Methods. Twenty-one healthy male subjects (mean age = 36 years 7 SD) performed 12 trunk extension exertions in standing and kneeling postures. Isometric tests were performed at 22.5°. 45°, and 67.5° of trunk flexion. isokinetic tests were done at three velocities: 30°/sec, 60°/sec, and 90°/sec. Electromyographic data were collected from eight trunk muscles to assess muscle recruitment under each condition. A prior; orthogonal contrasts were specified for analysis of both torque and electromyographic data. Results. The kneeling posture was associated with a 15% decrease in peak torque output when contrasted with standing; however, no concomitant change in trunk muscle activity was evident. Trunk hyperflexion (isometric tests) and increasing rotational velocity (isokinetic tests) were associated with reduced torque in both postures. Trunk muscle activity was primarily affected by changes in trunk angle and velocity of contraction. Conclusions. A reduced extensor capability exists in the kneeling posture, despite equivalent trunk muscle activity. The similar activation patterns in both postures suggest that the strength deficit does not result from alterations in trunk muscle function. Rather, it may be the consequence of a reduced capability to rotate the pelvis in the kneeling posture, due to a disruption of the biornechanical linkage of the leg structures. [Key words: electromyography, isokinetic, isometric, low back pain, posture. strength1 Spine 1997;22:1864-1872