Search Documents

By Lassaad Hazzar

The ultimate lateral resistance of piles in cohesive soil is studied using the well-known finite difference code, FLAC2D. The Modified Cam Clay (MCC) constitutive relation is adopted in the analyses to model the cohesive soil behavior, whereas the structural pile model with three degree of freedoms, available in FLAC2D library, is adopted to model the piles. The reliability of Broms's method, still used in the current design practice of piles under lateral loads, is verified. Comparisons between the ultimate lateral resistances of piles and those deduced from the graphs proposed by Broms (1964) are presented in graphs. Different factors thought to affect the lateral resistance of piles in cohesive soil, not adequately considered in Broms's method, such as clay stiffness, pile length, pile diameter and axial load are parametrically studied. A special concern is devoted to elucidate the effects of over-consolidation ratio (OCR) on the ultimate lateral resistance of piles in cohesive soil.

Aug 1, 2013

By Henry Otto

THE anthracite industry can be divided into two parts-the underground, or mining, and the outside, or preparation or manufacture. To understand recoveries in the two branches, some of the history of the industry and the changes that have taken place in the past century should be considered. It is a long step from 1807, when 55 tons were produced in the Wyoming field, to 1917, the peak year, when 80,841,223 tons were shipped to market from all the fields. In 1820, the Lehigh Coal Co., the predecessor of the Lehigh Coal & Navigation Co., shipped 365 tons in arks down the canal of the Lehigh Navigation Co. The Schuylkill field was not opened until 1822, when 1480 tons were shipped. The Wyoming field really became a producer in 1829, when 7000 tons were mined and shipped. It is well to note, at this time, the passing of the Coleraine colliery after a life of 88 years; in collieries of this age will be found the. romance of the region, as well as the history of the changes to date.

Jan 1, 1925

By Kjell Karlsrud

"Abstract New semi-empirical design procedures for the determination of ultimate shaft friction and load-displacement response of axially loaded piles in clay are proposed. Hereunder also prediction of how the capacity will build up with time following the pile installation, primarily as result of reconsolidation. A main basis for developing the new procedures was detailed review and re-assessment of results from a series pile load test programs published over the past 30 years on piles well instrumented to monitor soil- and pore pressures as well as load distribution along the pile shafts. Two new alternative procedures are proposed for predicting the ultimate shaft friction; a-approach using the normalised undrained strength based on direct simple shear tests as a main correlation parameter, and ß-approach using the overconsolidation ratio, OCR. Both approaches include the effects of the plasticity index of the clay, Ip, which is shown to have an especially large impact on the correlations when Ip<25. It is recommended to use both methods in design practice, and select design values for the ultimate shaft friction that represents an average for the two methods. Pile diameter, length or stiffness, or whether the pile is open- or closed-ended seem to have little impact on the shaft friction. However, a moderate effect of pile length or flexibility on the total ultimate pile capacity comes out of the proposed t-z curves, which include some post-peak reduction. The proposed procedure for predicting the time for set-up is based on linear radial consolidation theory. The main input parameters are the insitu permeability and virgin modulus number (or virgin compression index) of the undisturbed clay. The same basic formula and correlations are applicable to both open and closed-ended or partially plugging piles.IntroductionThe design procedures presented herein are primarily based on observations and data collected in connection with “fully instrumented” pile testing programs that the author has been responsible for or has become involved with over the past 40 years, or that have been found in the literature.It was a pre-requisite for the test programs included that there were sufficient high quality soil data available to give a reliable determination of the true in-situ strength and compressibility characteristics of the clay deposits. The soil conditions range from soft NC clays with undrained shear strength down to about 15 kPa, to very stiff clays with undrained shear strength up to about 500 kPa and OCR up to 25. The plasticity index of the clays mostly lies in range 12 to 60 %."

Jan 1, 2014

By Michael Windhager

UltimaTM rolls have been designed for intermediate and finishing stands of rod and bar and small and medium section mills. The rolls and rings are spun cast, with a highly alloyed working layer and a tough nodular iron core. Microstructure and hardness level can be adjusted over a wide range, which allows us to adapt the rolls to differing rolling conditions. After introducing the UltimaTM concept, this paper will describe the results of UltimaTM rolls achieved in various mill applications, like finish rolling of rebar, and slitting. Special emphasis is given to performance gains when using UltimaTM rolls, compared to standard rolls. This paper also examines the impact of UltimaTM rolls on mill and roll shop productivity.

Jul 30, 2018

By Wenxian Zhu, Xuema Li, Patrick R. Taylor

"Experiments were performed in a non-transferred arc, thermal plasma flow reactor to investigate the synthesis of ultra fine boron nitride (BN) powder from the reaction system of boron oxide (Bz03), methane (CH4), ammonia (NH3) and hydrogen (H2). Argon (Ar) and nitrogen (N2) were used as plasma gases. The thermodynamics and kinetics of the synthesis reactions were examined and a chemical reaction mechanism was proposed. The powders produced under certain operating conditions had high purity and good conversions. All the products were extremely fine powders (< 30nm) and were uniform in size distribution. The powder products were analyzed by chemical and physical characterization. The effects of the reaction variables on the conversions from B203 to BN and the purity of the products were investigated.IntroductionIn the past few decades, boron nitride (BN) has attracted a great deal of interest because of its excellent thermal, chemical and electrical properties (1-4) It has a high thermal stability and thermal conductivity. Chemically, it is very stable and is not wetted by most molten metals and slag. It is also an excellent low loss insulator. Since hexagonal boron nitride (h-BN) is light in weight, strong and easily fabricated, it has applications in a variety of specialized high temperature areas, such as a high temperature lubricant, crucibles for molten metals, thermocouple protection tubes, break rings for horizontal continuous casting of steel, and friction reducing coatings. In cubic form, boron nitride is one of the hardest materials known, second only to diamond, and it is an excellent material for tools in which the use of carbon based materials is limited by oxidation or reaction with metals."

Jan 1, 1998

Since early-2001, Kalgoorlie Consolidated Gold Mines (KCGM) has successfully operated an ultra fine grinding (UFG) circuit to supplement its roaster capacity for the treatment of the refractory gold flotation concentrate. A second UFG mill was installed in 2002 taking the total UFG capacity to over 20 tph while grinding to 11 to 12 microns and achieving over 90 per cent gold recovery. A development program in 2002/3 involving plant trials, pilot plants and laboratory testwork resulted in process improvements and a better understanding of the milling and gold leach processes that assisted in narrowing the gap between UFG and roasting. This paper details the operation of the ultra fine grinding process at KCGM as a non oxidative treatment for the extraction of gold from a refractory ores.

Jan 1, 2003

By Abb Raymond

Finely processed industrial minerals in "powdered" form have long been utilized by the plastics, paint, rubber, paper, ceramics, and adhesives industries as fillers, extenders, coatings and special additives. These minerals, primarily calcium carbonate, talc, kaolin, titanium dioxide, and the like, have provided economic, uniform and consistent base materials which have, in turn, been used by the referenced industries to manufacture quality products. The focus of this paper will be the development of equipment and systems at ABB Raymond for the dry processing of such non-metallic minerals in order to meet what have become increasingly stringent requirements of the producers of these minerals. Changes in these requirements seem to have been accelerating rapidly during the last ten years, and it is expected this process will continue into the 1990&apos;s.

Jan 1, 1990

By A. W. F. Smith, P. B. Prangnell, D. N. Crowther, P. J. Apps

It is well known that the refinement of grain size in metals leads to a significant improvement in important mechanical properties. As part of a European collaborative project, processing schedules have been investigated aimed at producing a homogeneous ultra-fine ferrite and spheroidised carbide aggregate microstructure structure in high carbon (CMn) steels (0.6-1.2wt%C), via conventional &apos;warm&apos; rolling and innovative Equal Channel Angular Extrusion (ECAE). Suitable deformation schedules were determined from dilatometry and thermo-mechanical Gleeble simulations. Evidence of an ultra-fine ferrite and carbide aggregate microstructure following &apos;warm&apos; rolling is given. A significant improvement in tensile strength, particularly proof stress (0.2%) was also noted in comparison to material deformed at higher temperatures. Concurrent Equal Channel Angular Extrusion (ECAE) experiments investigated microstructural evolution with incremental strain. Extensive analysis was carried out using various techniques, including high resolution Electron Back Scattered Diffraction (EBSD). Evidence of ferrite grain refinement was noted in a eutectoid composition steel. A sub-micron ferrite structure was observed following high strains (E-3.33) and the mechanical properties exhibit a marked increase in tensile strength.

Jan 1, 2004

By Choi Sang-Ken, Chung Hun-Saeng, Kim Byoung-Gon, Lee Jae-Jang, Park Chong-Lyuck

"Graphite has unique properties such as high thermal resistance, low thermal expansion coefficient, and good thermal and electrical conductivity, and is often utilized as coating materials for electrical conductors, TV Brown tubes, electromagnetic shields, and so on. Additionally, its excellent lubrication property is widely used in oil and solid lubricants. Finely ground graphite particles in the sub-micron range are commonly used for these applications.Sub-micron fine graphite particles are typically prepared in liquids by vibration ball mills. However, it is known that the wet process takes long periods of grinding time like 24 hours or more and requires a series of subsequent highenergy operations such as de-watering, drying, regrinding and classification. On the other hand, there would be numerous advantages if fine grinding could be done effectively in dry atmosphere. However, since crystalline graphite has a layered structure giving a high lubrication property, its dry grinding, especially when obtaining sub-micron size particles, is extremely difficult. The shape of the graphite particles is also important for its utilization since particles with flaky shape can maintain relatively high electrical and thermal conductance as well as lubrication ability. Therefore, it would be necessary to reduce the size of graphite particles into fines with flaky shape while grinding proceeds. Dry grinding characteristics of natural graphite under various atmospheric conditions with gases using different mills were studied, and fine flaky particles by grinding the graphite intercalation compounds and the exfoliated graphite were produced. However, there were no sufficient investigations on the size reduction of natural graphite at low atmospheric pressures in attritional milling conditions. The main purpose of this paper is to provide sub-micron fine grinding characteristics of natural crystalline graphite at various degrees of low atmospheric pressure, and to discuss the size reducing models in an attrition mill"

Jan 1, 2003

By Choi Sang-Ken, Chung Hun-Saeng, Kim Byoung-Gon, Park Chong-Lyuck

Fine grinding of crystalline graphite was conducted using a dry attrition mill with a vacuum system to investigate the characteristics of size reduction. Low pressure and high temperature conditions in the grinding mill were found to greatly improve the efficiency of the size reduction of graphite. Natural flaky graphite of .100 mesh was ground into sub-micron sizes, then over 90% of the product were able to be reduced below 1?without disrupting their crystallinity in a short period of time. Reducing the atmospheric pressure in the grinding environment promotes the removal of chemical species such as oxygen and water molecules adsorbed on the graphite particle, resulting in effective size reduction while maintaining the crystallinity of graphite.

Jan 1, 2003

By Christopher Davey, Professor Emeritus, Marian Mazurkiewicz, Peter Kanjorski

The concept of a high pressure liquid jet mill with highly unsteady flow, has been developed and recently patented by Cornerstone Technologies LLC (CsT), for the purpose of micron and sub-micron particle production. The mill accepts feed sizes up to 15mm for some materials and is capable of sub-micron production. Successful material range from precious metals such as silver and palladium to dielectric components and substrates such as Barium Titanate slips, zirconia, titania and silica. The process has also succeeded in adequately reducing the size of materials for both composite and coating uses such as anthracite coal, graphite, chrome metal, wollastonite and more than 100 others. A unique design approach has been taken to highly maximize the energy flux in the mill’s chambers to create extremely high turbulence and destructive cavitation. This is assisted by shock waves, which cause particles to undergo ultra high frequency pressure pulsations, high frequency collisions and then abrasion, shattering, hydro-wedging, and cleaving. Due to these extreme properties the processing occurs in just fractions of a second allowing throughputs up to 1000 kg/h on a machine that would fit inside a 60 cm box. The technical solution and technological advance, as well as the environmental and economic benefits indicate rapid and wide spread acceptance of high-pressure liquid jet milling in modern industry.

Jan 1, 2003

By N. N. Rulyov

"Starting from fundamental principles of colloid-hydrodynamic theory of disperse systems we have shown that application of strongly non-uniform hydrodynamic fields allows to achieve not only faster rates of flocculation of suspension, but also supports significant improvements in the quality of clarified water and separation characteristics of solid phase. Specifically, it has been experimentally proven that the new treatment method based on these principles (then termed as ""ultra-flocculation"") allows:•,Increase the output of thickeners and pressure filters by 1,5-1,7 times;•,Decrease solids fall through into the filtrate in the process of vacuum filtration by 2¬3,5 times;•,Improve the rate of purification of water phase in the upright thickener by 1,5-1,9 times;•,Decrease flocculant consumption by 1,5-3 times;•,Increase the effective operational life time of cloth filters by 3-4 times;•,Ensure sustainable operation of separation equipment, i.e. decrease the sensitivity of process to variation in suspension concentration, as well as to variations of suspension composition and dispersion characteristics;•,Apply flocculant solutions of concentration 2-3 times higher, thus increasing the capacity of equipment used for solutions preparation."

Jan 1, 2004

By Kouji Mimura, Tamas Kekesi, Yongfu Zhu, Masahito Uchikoshi, Minoru Isshiki

"The formation and anion exchange sorption of chloro complex ions can offer a great potential to be utilized for the separation and purification of metals in aqueous solutions. Available stability data were primarily used to estimate the predominance of chloro complex species, indicating the feasibility of such separations. Anion-exchange sorption functions, describing the equilibrium distribution of a number of important elements have been determined by the batch equilibrating method in the practical HC1 concentration range. Various oxidation states were stabilized by the addition of appropriate agents. Tendencies in oxidation, complex formation and anion exchange sorption were confirmed by spectrophotometric investigations. Based on the fundamental results, anion exchange processes have been developed for the purification of iron, cobalt, copper and zinc. The efficiency of separation was assessed and the procedure optimized by the analysis of experimental elution curves. Results have demonstrated that by properly controlling the oxidation states and HC1 concentrations, practically all the impurities can be eliminated. Computer programs have been developed to estimate complex formation and redox equilibria, to screen and correct analytical data, to determine distribution coefficients and to evaluate efficiencies of separation.IntroductionBase transition metals have long been used as the staple materials in various fields of industry. In general, there has been an increasing tendency in purity requirements but recent advances have created a rapidly increasing demand for ultra-high purity metals. To give a few examples, ultra high purity copper can be used as bonding wire and interconnection in integrated circuits, or as material for superconductor stabilizing, high-field magnets, beside its use in cryogenics and ultra high vacuum technology [1]. Iron holds promises as a constituent element in the ß-FeSi2 material to be applied in new opto-electronic devices [2] and it is currently used, together with chromium and manganese, in the production of special magneto-optical materials for digital recording. The use of ultra high purity manganese and chromium in semiconductor technology is evolving. Although not considered a transition metal, zinc is also treated here because of the major significance in compound ZnSe semiconductors [3], and the possibility to purify it by the anion exchange method."

Jan 1, 2000

By Karin Bäppler

A new polyhalite fertilizer mine is currently being developed in the UK by Anglo American Crop Nutrients. The project includes the construction of a Mineral Transport Tunnel almost 37 kms long to house a conveyor belt that will move polyhalite from the production shaft at the mine to a materials handling facility at the port. The project sets a new standard in terms of an ultra-long tunnel drive and sustainable, environmentally friendly and efcient material transport. The paper highlights in particular the . m diameter TBM in use for the construction of the ultra-long tunnelling section.

Jun 23, 2024

By Roberto Balarini Junior

Tribological behavior of Si3N4 balls sliding against Al2O3 discs in water was investigated by studying the influence of parameters such as initial surface roughness and circular axial run-out of the discs. The objective was to relate these parameters with the occurrence of the phenomenon known as ultra-low friction coefficient (ULFC), which is characterized by µ < 0.01, including the correlation with running-in duration. As a general trend, greater initial surface roughness and circular axial run-out resulted in greater running-in duration. In addition, it was verified that a mixed lubrication regime (hydrodynamic and boundary) is required to guarantee the occurrence of ULFC by comparing the calculated minimum film thickness with the composite roughness of the worn surfaces. Also, ICQ-OES analysis of the water after the tests indicated that a silicon concentration greater than 1.3 mg/l should be fundamental for the occurrence of µ < 0.01.

Jul 31, 2018

By Henrique Silva Furtado

Concerning production of low phosphorus steel critical grades at ArcelorMittal Tubarão site, bottom blowing system plays a very important role. For those systems with independently controlled tuyeres, some non-uniform bottom blowing patterns seem to be promising in improving metal-slag mixing; however, based on computational fluid dynamics (CFD) results of ArcelorMittal Tubarão’s post oxygen bottom blowing, this may not be generalized. Also, from industrial trials it became clear that higher the bottom blowing flow rate, the closer were the end point P to the equilibrium. Despite this result an analysis of the apparent mass transfer coefficient has shown a week correlation with the classical power stir correlation suggesting a more complex kinetic limiting step for phosphorus removal.

Jul 30, 2018

By K Zhao, H Gong, B Li

Health and safety are the first priority for Australian minerals sector. Australia has a global reputation in the mining industry. However, accidents occur every year. Legislation and regulation are important to prevent the accident from occurring, so do the new technologies. It is sad to witness the collision incident persisting and the long called collision avoidance system (CAS) is still not widely used in underground mines. The main reason is that the existing systems are still not advanced enough. The current CASs utilise GPS, infrared, ultrasonic, RFID, Radar, electromagnetic etc have their limitations and disadvantages. For instance, GPS is widely used in a surface mine, but it cannot be applied in underground mine; Infrared and electromagnetic have the false positive problem.

Sep 1, 2024

By K. Neumann

"INTRODUCTION For many automation and safety tasks in open cut and underground scenarios it is crucial to have highly reliable distance measurements at hand. These measurements can for instance be used to obtain the exact position of a machine in one-, two- or even three dimensions. Research and development has shown interest in the ultra-wide-band technology (UWB) in recent years. While for this technology short range, high speed data transfer is the current main research focus, the technology can also be used for highly accurate ranging applications. Due to the use of a very wide frequency band, it is robust against disturbances of many types (e.g. EMC, rain, dust etc.) and is therefore attractive for the use in mining applications. The wide frequency band also offers benefits for ranging applications. Especially in environments with strong multipath problems such as in underground mines it is possible to focus on the dominant signal propagation path, thus increasing the reliability of the measurements. [1] State-of-the-art UWB ranging equipment claims precision within the range of a couple of centimeters and working ranges of more than hundred meters. At the Institute for Mining and Metallurgical Machinery (IMR) at RWTH Aachen University in Germany a modern UWB system was examined in several laboratory and real life tests to examine the feasibility of UWB bases ranging equipment in mining applications. UWB TECHNOLOGY The term ultra-wide-band denotes radio systems that use an ultra-wide frequency band. A common definition for UWB radio systems is that it needs to work on a frequency bandwidth of more than 500 MHz or a bandwidth equal to 20% or more of the center frequency [1]. Due to the ultra-wide frequency bandwidth UWB systems overlap the frequency spectrum of narrow band radio technologies like Wi-Fi, Bluetooth and other mobile communication systems which use a defined carrier frequency onto which information is modulated on (e.g. by using frequency or phase modulation). In order to not conflict with these other radio applications, it needs to be ascertained that the transmission power of a UWB system on a given frequency is so low that narrow band systems are not affected by it. As opposed to this only a small fraction of the UWB system’s bandwidth is affected by the narrow band system. The unaffected remaining bandwidth is sufficient to reconstruct the original signal, even if additional noise is present. Figure 1 shows the power spectral densities of popular radio standards [6], [7], [8]. A significant driver of research and development of UWB systems has been wireless high bandwidth communication. Using an ultra-wide frequency band is highly desirable here, as the channel capacity is dependent on the bandwidth. So far systems have been realized especially for short distances (e.g. wireless USB or Wireless HDMI) but beyond that, communication systems for long distances (several kilometers) are possible [2]. Advances in semiconductor technology led to a reduction in power dissipation of such systems. This enabled higher integration levels which in turn facilitated smaller solution sizes for space constrained applications [3]. Nowadays, UWB is also used for high-precision ranging applications [4], [5]."

Jan 1, 2015

By K. van Netten, T. P. Ernst

"Froth flotation has been used successfully for about a century in the beneficiation of both coal and mineral particles. With the on-going trend towards lower feed grades, however, there is a need to transform this technology in ways that can deliver ultrafast separations, with strong selectivity, and recovery, covering a broader size range. It should be recognised that the hydrophobic effect, with its highly selective and long-range interactions, will most likely underpin any new technology. We identified the separation of the concentrate from the tailings as the rate determining step of conventional flotation technology. This limitation was then addressed by developing a novel flotation technology, insuring the formation of a concentrate that could be separated more rapidly from the tailings. We introduced a novel binder medium, a highly concentrated water in oil emulsion, to act as the focal point for hydrophobic adhesion, effectively replacing the air bubbles used in conventional flotation. The hydrophobic particles adhere to and become embedded within the binder, forming saturated agglomerates that float upwards. Moreover, by forming these large and resilient agglomerates, the product can be quickly dewatered over a screen and separated almost immediately from the tailings. Remarkably, this new binder permits residence times in the order of a few seconds under batch conditions. This paper examines the performance of the technology as a function of the oil wt% added to the slurry. The paper also examines the performance of the technology as a function of the particle size, showing a decline as the particle size exceeds 0.50 mm.INTRODUCTIONFroth flotation involves the collision and adhesion of hydrophobic particles to rising air bubbles, the carrying of those particles from the bubbly-pulp zone into a froth zone, and subsequent drainage and migration of the pulp to achieve the final concentrate (Wills, 2006). Within a Jameson Cell the feed slurry and air bubbles are brought into intense contact within the active area of the downcomer, achieving rapid kinetics of hydrophobic particle adhesion to the air bubbles (Harbort et al., 1994). However, once the bubble laden product and tailings emerge from the downcomer there is the need for separation of the concentrate from the tailings, an inherently slower process. In other devices such as mechanical cells the initial kinetics of particle adhesion are far slower, relying on the turbulent eddies throughout the cell, while in a column the kinetics rely upon an even slower process of bubble interception with suspended and settling particles (Gorain, 2007). However, in all cases the driving force for segregating the bubbles from the tailings, and the drainage of the froth are inherently the same. We do note, however, recent advances by Galvin and co-workers in achieving so-called Fast Flotation, utilizing a system of inclined channels to dramatically increase the segregation rate of bubbles from the tailings, permitting much higher gas and feed fluxes to be applied, achieving up to a ten-fold throughput advantage (Dickinson et al., 2014). Any further improvement within the existing flotation paradigm would require the introduction of centrifugal forces, but this would also require the formation of much finer bubbles than is typically used given the tendency of relatively large bubbles to reach a limiting slip velocity due to deformations and increased drag. Across all flotation devices we argue the rate determining step remains the segregation of the bubbles from the tailings."

Jan 1, 2016

By Y. A. Attia

A study was performed on selective flocculation and dispersion for ultrafine coal cleaning. A totally hydrophobic polymer, FR-7A, was employed as the selective flocculent for coal, sodium metaphosphate (SMP) as the general dispersant for shale and a synthetic polymeric product, polyacrylic acid-xanthate (PAAX), as the selective dispersant for pyrite. In the adsorption tests, nephelometry and spectrophotometry were employed for determining the concentration of FR-7A and PAAX in the solutions respectively. The adsorption tests indicated that: a) FR-7A has a higher affinity toward coal and pyrite than that for shale; and b) PAAX has a much higher affinity toward pyrite than toward coal and shale. In the selective flocculation tests, the ash-forming minerals can be efficiently rejected using sedimentation as the separation method. However, due to their relatively high specific gravity, pyrite particles co-settle with the coal flocs. To reject fine pyrite, a froth flotation was used for floc separation. The one-step flocculation-flotation process could reject more than 70% of each of the pyritic sulfur and ash minerals, while recovering more than 85% of the coal.

Jan 1, 1990