Search Documents

By Amr Sallam, Ahmad Mohamed, Mohamed Alrowaimi

Renewable energy, in the form of wind and solar, has emerged as main source of energy in the modern society. The wind industry has substantially grown over the last two decades to become a key player in providing energy to public. Wind turbines are getting larger, taller, and more efficient every year. The foundation is a major component of the wind turbine system. The wind turbine foundation must provide short and long-term stability for the overall turbine to allow continuous and safe turbine operation for energy production. The turbine serviceability and stability requirements must be geotechnically and structurally satisfied. In North America, major foundation types currently utilized in the wind industry include gravity spread foundation, mono pier foundation, and pile foundation. In this case study, a Post Tensioned Pile Cap (PTPC) foundation was used to support a 3.15-3.4 Megawatt turbine with 125M Rotor supported on 87.5M-hub-height tower. Soil anchors in the form of Auger-Pressure-Grouted-Displacement (APGD) piles and Continuous Flight Auger (CFA) piles were utilized. Four distinct subsoil conditions were identified, and for which four pile designs were adapted. Due to the occasional encounter of stronger soils at 50 to 55 feet (15.2 to 16.7 m), shorter pile design was preferred. To satisfy the design uplift load, pile post grouting were utilized to increase the shaft capacity of the piles. In this paper, the pre-production pile load test program will be described. The pile load test procedure, analysis, and results will be presented. A discussion will be provided, which led to the selection of the optimum pile design to support the high tension loads taking into consideration pile length limitations.

By Federico Pagliacci

Continuous Flight Auger (CFA) technique represents an important technological advance in the construction of piles in soft soils. The possibility of excavation under the water table with no need for drilling fluids, along with high productivity, have resulted in this technique?s becoming widespread in many countries. However, CFA technology has limitations because of its difficulty in penetrating hard layers and cross strata with cobbles and boulders. In these situations, pile verticality may be an additional problem. The Cased Augered Pile (CAP) technique consists of penetrating the soil with an auger housed in a casing. Two independent rotary heads sliding along the rig mast operate the auger and the casing. By adjusting the height of the casing shoe and auger bit according to soil type, it is possible to drill piles in very severe conditions - in the presence of cobbles and boulders - and to socket the pile into the rock. The use of a steel casing enables improved pile verticality. Therefore, the CAP technique is also used to construct secant piles to be used as diaphragm walls. The limitations of this technology are the depth, usually no more than 27 m (88 feet), and the size of the rig that supports the drilling tool, no less than 70 t (77 short tons) in working conditions. This paper illustrates CAP technology, the drilling system, and the characteristics of concrete and steel reinforcement and offers a case study of the Palermo-Carini second railway line, which used CAP to construct the new 30 km (18.6 mi) railway line, 20 km (12.4 mi) of which passes through the very congested downtown area of Palermo. More than 300,000 m (186.4 mi) of piles have been drilled in dense calcarenite formations with unconfined compressive strength of 15-25 MPa (2,200-3,600 lb/inch2), soft clay, and silt formations.

By Federico Pagliacci

Continuous Flight Auger (CFA) technique represents an important technological advance in the construction of piles in soft soils. The possibility of excavation under the water table with no need for drilling fluids, along with high productivity, have resulted in this technique’s becoming widespread in many countries. However, CFA technology has limitations because of its difficulty in penetrating hard layers and cross strata with cobbles and boulders. In these situations, pile verticality may be an additional problem. The Cased Augered Pile (CAP) technique consists of penetrating the soil with an auger housed in a casing. Two independent rotary heads sliding along the rig mast operate the auger and the casing. By adjusting the height of the casing shoe and auger bit according to soil type, it is possible to drill piles in very severe conditions - in the presence of cobbles and boulders - and to socket the pile into the rock. The use of a steel casing enables improved pile verticality. Therefore, the CAP technique is also used to construct secant piles to be used as diaphragm walls. The limitations of this technology are the depth, usually no more than 27 m (88 feet), and the size of the rig that supports the drilling tool, no less than 70 t (77 short tons) in working conditions. This paper illustrates CAP technology, the drilling system, and the characteristics of concrete and steel reinforcement and offers a case study of the Palermo-Carini second railway line, which used CAP to construct the new 30 km (18.6 mi) railway line, 20 km (12.4 mi) of which passes through the very congested downtown area of Palermo. More than 300,000 m (186.4 mi) of piles have been drilled in dense calcarenite formations with unconfined compressive strength of 15-25 MPa (2,200-3,600 lb/inch2), soft clay,

Jan 1, 2017

By John R. Grillo, Gordian Ulrich, Franz-Werner Gerressen

Most geotechnical construction professionals are aware of piling using hydraulic drill rigs and the so-called Kelly drill mode. Kelly drilling has many advantages as it can work with a wide range of tools facing almost all types of soil and rock conditions. Kelly drilling can also deal with diameters up to 10 ft (3.00 m) and bigger or depths of more than 330 ft (100 m). Nonetheless, there is a concern about Kelly drilling as it is a relatively slow installation process. Therefore, an alternative piling method like Cased CFA (CCFA) Piles (Cased Auger Cast Piles) provides a significant advantage in terms of installation performance, schedule and cost saving potentials. Major application for the Cased CFA system is the secant pile wall construction. Against the traditional secant pile wall systems like fully cased bored piles or CFA secant piling the Cased CFA secant pile wall system has the advantage in cost and time against the fully cased system and in quality against the standard CFA system. This paper will describe the methodology and installation process in general as well as first reference projects carried out in the United States. This paper will present the results in cost and schedule saving using this method. In addition, we will also describe the limitations of this method. INTRODUCTION In the changing construction environment, companies are searching for new technologies or improvement of existing technologies to complete their projects in shorter time frames to provide a good economic solution. Especially with the focus of increasing urbanization, the aim of fast construction becomes more and more important. When thinking of piling, most people will have the same picture in mind: that of a hydraulic drill rig working in Kelly drilling mode; however, the perpetual drill rig development provides a number of options for the execution of specialist foundation projects, either for foundations or for pile walls when using single pass applications like CFA, Cased CFA and Full Displacement Piling (FDP). Single pass means, in general, that the tool is pushed and rotated into the ground to the final depth in one stroke. After reaching the final depth, concreting is started and concrete is pumped continuously while the tool is withdrawn.

Jan 1, 2019

By Henk van Muijen

From an interesting and intriguing scientific research topic, deep sea mining has altered into an interesting mining prospect over the last years. Ten years ago most of the focus was on geological investigations, searching for typical deep sea deposits and getting answers on where we can find them and how these deposits were formed. At this moment we know much more about the interesting deposit possibilities and with our quest for minerals, metals and other materials to feed global economic growth, answers as to the technical and economic feasibility to mine these deposits are sought. This is not a new phenomenon as we already witnessed such question late 1970?s and early 1980?s. Most of the focus was on mining manganese nodules and brines in the Red Sea driven by the report of the Club of Rome that predicted shortages in near future at that time. Development went different, but later in the 1990?s a rival of interest could be noticed for mining deep sea deposits.

Jan 1, 2010

By L. E. Collins

"In western Canada, many new wells contain a significant fraction of H2S. As well, many older wells become increasingly sour over their operating lifetime. For these reasons, there has been increased demand for linepipe and casing for sour service applications in recent years. This paper will review the metallurgical factors which must be considered in designing steels for such applications. IPSCO’s development of linepipe and casing, and experience in fabricating products to meet test standards specified for sour service applications will be summarized. IntroductionWestern Canada produces the majority of Canada’s domestic crude oil and natural gas. A complex system of pipelines has been built to gather the oil and gas from the fields for transport to refining and/or cleaning operations. The gas carried in these pipelines can be either sweet or sour (i.e. containing no H2S or containing H2S) depending on the nature of the field from which it came. Many new fields contain a significant fraction of H2S and many older fields become more sour as their time in production increases. This uncertainty regarding product condition influences the user’s choice of materials for both casing and pipeline applications.It is well known (Merrick, 1989) that hydrogen induced cracking (HIC) will occur in steel when three conditions exist simultaneously: (1) the presence of H2S gas, (2) moisture, and (3) a susceptible material. Steelmakers can only address the latter of these factors. Development of steels to meet test requirements of sour service has been a major focus of IPSCO’s development work for several years."

Jan 1, 1998

By E. R. Smith

ANALYSIS of the requirements for gun perforation equipment suitable for penetrating casing and cement showed that these points would be involved: (1) Powder charges electrically detonated under high fluid lieads and at remote distances. (2) Selective firing of sliots in sequence. (3) Sufficient velocity for the bullet to penetrate at least two strings of seamless casing and all cement beyond the strings. (4) Heat-treatment of steels to withstand great pressures and penetration. (5) Esclusiorl of fluid under extremely high hydrostatic pressure. (6) Stranded steel wire line acting as weight - suspending and current - carrying medium. (7) Firing controls operated above the surface. (8) Determining gun depth and suspended weight by means of the wire line. (9) Portability for field use.

Jan 1, 1936

By C. M. Campbell

In his report on the Coal Resources of Southern Vancouver Island, Mr. J. D. MacKenzie stated that: "For various reasons it has been imagined that the coal deposits of Vancouver Island are extremely large and readily available." "Unfortunately," he added, "neither of these assumptions is correct." The chief disability under which the Island mines now labor does not concern the extent of the deposits. There is ample coal for the present demand. It does, however, concern the availability of the coal. If it were readily available the fuel-oil competition would not be serious and there would be no competition with Alberta, American, Welsh, or Australian coal along the Pacific Coast, for Vancouver Island coal could be produced at a price that would cut out all competition. The outstanding operating difficulty common to all Island mines is the extreme irregularity of the coal seams. To most people a coal seam is synonymous with uniformity, and in most coal seams a condition found at one point will be repeated at other points in the same seam throughout the basin. The accompanying drawings show how very far this is from being true in the Cassidy mine, which, in many respects, is typical of Vancouver Island mines. Figure I is a plan covering about 160 acres of the Douglas seam, the only workable seam in this part of the district. The area shown represents what has been the best producing part of the mine and indicates the very large percentage of the seam where the coal is either entirely lacking or so small in amount that it cannot be profitably recovered.

Jan 1, 1924

By Robert L. Martin, Brian W. Stump

"The Black Thunder Mine is located in the Powder River Basin of Northeastern Wyoming. Over 39.2million tons of coal were produced at the Black Thunder Mine in 1996. Just over 100 million pounds ofANFO/Emulsion blend were consumed in that same year. Currently around 30% of the overburden is cast to final with the use of explosives. With plans for a mine expansion, explosives will continue to play a very vital roll well into the future."

Jan 1, 1997

By Jeff Wachendorf

As the title "Cast Blasting Around Town" implies, this paper details the starting of a cast blasting program in and around the town of Colstrip, Montana. As strip ratios have increased, the need to adapt and find solutions to provide coal at a reasonable cost to the captive power plants has risen. Colstrip, Montana has a long history of coal mining which dates back to the early 1920's when Foley Brothers began supplying coal strictly for powering locomotive engines. Early mining days starting in the 1920's and the progression up through the 1970's when mine mouth power plants were built will be discussed. To accomplish the desired results, early mining techniques included steam and electric powered equipment as well as a lot of actual horse power.

Jan 1, 2009

By R. H. Sailors

During the last 15 years, the North American Mining Industry has experienced increasing usage of cast high chromium white iron grinding media in wet grinding applications. First introduced into the cement industry (klinker grinding) where wear rate reductions of four or five times have been realized compared to steel balls, this same grinding media serve the iron, copper, and phosphate markets by resisting not only impacts and abrasion, but also corrosion which occurs in wet grinding. In these markets, single mills containing 250,000 kg of grinding balls are not un-common and hence the economic potential with respect to lower wear rates can be significant. Add to reduced wear rate the increased production efficiency that is possible and it is readily understood why much of the mining industry uses cast high chromium grinding media. Metallurgically, the alloys used consist of a martensitic matrix containing hard M7C3 eutectic carbides. Carbon (2.0 to 3.5%) and chromium (12 to 277.) are characteristically used to arrive at the desired properties.

Jan 1, 1989

By Bert S. Hall

"The purpose of this paper is to review the evidence at hand concerning the earliest centuries of cast iron in Europe, from roughly 1400 A.D. until the second half of the sixteenth century. For the most part it is concerned with the relationship between two technologies which emerged first in China and then later appear in Western lands, gunpowder weapons and iron founding. We should not assume, as I hope to show later in this discussion, that weapons constituted the only product for which the iron founder had any market, but it is clearly true that attempts to produce weapons constituted the most severe technical challenge for the early founder. Firearms appear for the first time in Europe in the 1320s and develop into significant weapons on the field of battle by the end of the century. Theirs is a complex history, subject neither to easy summary treatment nor to simplified models of development. I hope to be able, through the analysis of the evidence concerning cast iron, to show that one important strand in the fabric of gunpowder's history concerns the materials from which cannon could be made. This question is subject to a number of shades of meaning, because ""cannon"" can be made for many purposes under a profusion of different names, and under sharply varying conditions of use. As a result, the question of materials is frequently really a question of competing materials, and involves a complex set of factors, of which production costs and the ultimate safety of the user seem the most important. Judged in this manner cast iron was an important but unsatisfactory metal for weapons purposes until 1543, at which time English founders learned to make iron muzzle-loading cannon which could rival bronze ordnance in most important performance criteria, but which cost much less to produce. With that event, the history of cast iron and the history of weapons entered into the close relationship that persisted until the advent of rifled artillery made of steel in the middle of the nineteenth century."

Jan 1, 1999

Discussion of the paper of J. E. Johnson, Jr., The Effect of High Carbon on the Quality of Charcoal-Iron, presented at the Cleveland meeting, October, 1912, and printed in Bulletin. No. 74, February, 1913, pp. 173 to °14, and of the paper of Albert Sauveur, Notes on Cast-Iron, presented at the New York meeting, February, 1013, and printed in Bulletin No. 75, March, 1913, pp. 503 to 524. CHAIRMAN. JOHN BIRKINBINE :-Just 20 years ago I had the pleasure, when I retired from the Presidency of the Institute, of introducing my successor, and this afternoon it is my pleasure to ask my good friend Dr. Howe to open this discussion. PROFESSOR HENRY M. HOWE, New York, N. Y. :-This paper of Mr. Sauveur's is extremely interesting. It is one of those papers that one wishes to read in the quiet of one's study, where it can be read with great profit. There are many points which he makes which I think are of very great value, in particular as to the importance of getting fine ;grained graphite by a relatively rapid cooling, combined with a high percentage of silicon. That theory would seem to be very promising; how far it has actually been carried out very likely Dr. Moldenke can. tell us.

Jan 5, 1913

By K. Harms, T. D. Jones

TO unload large tonnages of lead bullion cast in 100-lb. bars is a problem which has confronted the lead refineries for many years. The bars, on arrival, must be restacked for unloading by truck or hand-charged to charging machines. Selected crews of labor, capable of working at sustained speeds for five- or six-hour periods, are required for this exhausting task. Due to the fatigue involved crew personnel changes rapidly. During the war it became increasingly difficult to maintain crews, especially in critical labor areas, so that the development of casting and shipping ten-ton lead blocks from the smelters to the refineries became a must in our operating program. For many years lead refineries, when making interdepartment or intradepartment transfers, have cast lead blocks weighing five or ten tons which are easily handled by crane by merely attaching the crane hook to a steel anchor embedded in the frozen lead blocks. In previous years, the practice was to use regular smelter slag pots which, due to their rounded shape, produced what were called "buttons" by the refinery personnel. The button-type blocks were unsafe as they rolled and tipped easily and were unsatisfactory for stacking since no piling pattern could be followed. To remedy this situation, flat-bottom molds came into general use and later the bottoms were made concave to prevent slipping.

Jan 1, 1946

By Albert L. Toenges

(1) The Castleman Basin was investigated by diamond drilling, engineering examination, and geologic study. Agreements permitting investigation of about 14,700 acres of land were entered into with 79 landowners. Eleven beds of coal between the horizons of the Harlem and Mercer beds were penetrated in drilling. These beds from top downward are: Harlem, Upper Bakerstown, Lower Bakerstown, Brush Creek, Upper Freeport Rider, Upper Freeport, Upper Kittanning, Middle Kittanning, Lower Kittanning, Mount Savage, and Mercer. The total estimated reserves of coal (measured, indicated, and inferred), 14 inches or more thick, in six beds follow: [Coal bed: Etimated reserves, tons Harlem _______________________ 23,430,000 Lower Bakerstown _______________ 44, 688, 000 Brush Creek ____________________ 23, 694, 000 Upper Freeport __________________57, 731, 000 Upper Kittanning ________________ 40, 450, 000 Middle Kittanning ______________42,276,000 Total________________________ 232,269,000]

Jan 1, 1952

A coal mine located in southern West Virginia recently set a world record for daily low-seam coal production using a Cat automated longwall plow system. In a 24-hour period on April 10 and 11, 2014, the Pinnacle Mine longwall produced 32,411 t (35,724 st) from the Virginia Pocahontas No. 3 Seam, in a seam height of just 1.42 m (56 in.) along the 298-m (980-ft) longwall face. The Pinnacle Mine, located near the town of Pineville and owned by Cliffs Natural Resources Inc., an international mining and resource company, operates a Cat Gleithobel GH1600 Longwall Plow System. A previous record was set by this system at Pinnacle in August, 2012 when 29,423 t (32,430 st) were mined in a 24-hour period. The record was set by the same system, mining its second panel after a comprehensive rebuild was performed by Carter Machinery, the Cat Dealer in that area. The rebuild encompassed a complete rebuild of the headgate and tailgate armored face conveyor (AFC) drive, the headgate and tailgate special AFC pans, the stageloader drives and return end, the complete crusher and all gearboxes for the plow, AFC and stageloader. Carter acquired the rights to sales and aftermarket support associated with the former Bucyrus mining products, both surface and underground, in 2013. ?Supporting and rebuilding a longwall plow system was a new experience for the Carter service team,? said Chris Curfman, president of Caterpillar Global Mining Sales and Support Division. ?However, given the record production results attained by the rebuilt system at Pinnacle, it?s obvious that they are up to the challenge of supporting the underground product lines at the same high standards and quality level that they have been delivering for many years on the traditional Cat surface mining products.? Tom Bluth, president of Caterpillar Global Mining Products Division, said, ?Caterpillar congratulates the Pinnacle team for this great achievement. Without their efforts and dedication this record would not have been possible. To safely deliver that kind of output from such a thin seam is remarkable. We have been privileged to work alongside their team to demonstrate the capabilities of Cat longwall mining technology. ?

By William Gleason

Despite a global slowdown in most mining sectors, Caterpillar, the world?s largest mining equipment maker continues to forge ahead with new, and improved offerings to the global mining industry. On Nov. 10, as part of its Loading and Hauling Mining Focus Session at its Tinaja Hills proving grounds south of Tucson, AZ, Caterpillar unveiled to customers and media its two latest mining products, the 994K wheel loader and 6020B hydraulic shovel. The Caterpillar 994K wheel loader builds on a nearly 25-year history of the 994 model but with one noticeable difference ? the 994K is bigger ? much bigger. Weighing in at 239,142 kg (527,218 lb) the 994 K is up to 20 percent larger and comes with up to 30 percent increase in payload capacity. This behemoth of a machine is currently being tested at Caterpillar?s Tucson Proving Grounds, Anglo Gold Ashanti?s Cripple Creek and Victor gold mine in Colorado and Taseko?s Gibraltor copper and molybdenum mine in British Columbia, Canada.

By M Rea, E O’Connell

Decarbonising explosives manufacturing and catalysing low-carbon mining supply is a significant global challenge. Low-carbon manufacturing precincts – clusters of geographically close businesses across multiple industries that share a goal of adopting firmed renewable energy and decarbonising process emissions – offer one potential solution. In an Australian first, Orica commissioned tertiary catalyst abatement technology in 2023 to mitigate greenhouse gas (GHG) emissions at its Kooragang Island (KI) facility in New South Wales (NSW), Australia. The EnviNOx® technology (ThyssenKrupp Industrial Solutions AG, Dortmund, Germany) used reduces nitrous oxide (N2O), a potent greenhouse gas arising as a by-product of nitric acid manufacture. As a result, mining customers in NSW are now benefitting from ammonium nitrate (AN) products that are almost 50 per cent less emissions-intensive than those Orica previously offered. The $37 million project is a private-public partnership that has involved partners across Federal and State government, global engineering and technology vendors, local community groups and local carbon advisors to overcome financial barriers.

Sep 1, 2024

By P. E. Nolan

The disproportionation of carbon monoxide is an important aspect of reduction processes, in the production of carbon filaments for composites, and in the removal of CO from CO,. It can also be a hindrance, causing carbon fouling of equipment and metal dusting. The reaction is thermodynamically favored at lower temperatures, but it occurs slowly. Catalysis of the reaction by transition metals has been examined. A materials science approach to the selection of a catalyst material and of optimum operating conditions is being taken in the present work. Of particular interest is characterization of a catalyst that can be repeatedly regenerated to prevent deactivation in long term use. Experimental data on a less studied catalyst, ruthenium, are reported.

Jan 1, 1992

A strategy is presented for a relatively. "low-tech" means for decontamination of streams . containing .low concentrations of toxic metals. Metal ion solutions were . circulate through fluidized beds of activated carbon which support bio-films ?of bacteria .that naturally excrete exopolysaccharides. The attached 'biomass is shown to significantly enhance nickel, cadmium and silver extraction from dilute solutions (5- l00mg/l). By heat treating (at 300º C) the metal/biomass/carbon particles, bio-sorbed silver was subsequently fixed to the carbon surface. This approach to metal decontamination may therefore also provide a route for dispersing and fixing catalytic metal particles over an activated carbon surface.

Jan 1, 1991