Search Documents

By Sergio N. Monteiro

Fibers extracted from the ramie plant have been traditionally used in textile and are now being considered as polymeric composite reinforcement owing to their superior strength. Recently the mechanical behavior of ramie fiber reinforced polyester composites was investigated but no significant improvement was found. Therefore, the objective of this work was to carry out a similar investigation by changing the type of polymeric matrix. Specimens with up to 30% in volume of ramie fibers incorporated into epoxy were bend-tested until fracture. The results showed a moderate improvement with a tendency of decreasing stress for higher amounts of ramie fibers due to the weak interface developed with the epoxy matrix.

Jan 1, 2009

By P. N. Anyalebechi

"The as-cast microstructure of two commercial-size ingots of aluminum alloy 3004 produced by the electromagnetic casting process was quantitatively characterized. This involved the quantitative determination of through-thickness and across-width variations in dendrite cell size, grain size, macrosegregation of alloying elements, interparticle spacing, and the types, volume fractions, and sizes of the constituent or second phase particles. More than ninety-five percent of the constituent phases in the ingots consisted of the A16(Mn,Fe) phase; the desirable a-Al 12(Fe,Mn)3Si phase was not detected in any of the ingots by Guinier X-ray diffraction analyses or electron probe X-ray microanalyses. A significant microstructural heterogeneity through the thickness and across the width of both ingots was observed. For example, macrosegregation, and the sizes of the constituent phase particles, dendrite cells, and grains increased concomitantly from edge to mid-width and from surface to center of the ingots. There was a -20% depletion (negative macrosegregation) of Mg and a +54-87% enrichment (positive macrosegregation) of Ti in the center of the ingots. With the exception of grain size, there was no significant microstructural difference between the two ingots examined. The causes and practical implications of the observed microstructural heterogeneity in the ingots are discussed.IntroductionThe first step in the fabrication of majority of wrought products of aluminum and its alloys is the casting of large ingots or billets of simple shapes (round or rectangular). The sizes of the ingots vary from 10 mm to 450 mm diameter or 25 mm to 780 mm thick. The quality of the finished products is established at the ingot casting stage. This is because the microstructural characteristics, such as secondary dendrite cell size or arm spacing, amount of alloying elements retained in solid solution, macrosegregation, and the characteristics of second phases, produced during casting cannot be reversed by subsequent processing. Up until twenty-five years ago, the effect of as-cast microstructure of large ingots on the structure and behavior of thin sheets (0.34 mm thick) during drawing and ironing processes was incorrectly assumed to be minimal or nonexistent. This was based on the erroneous notion that the thermal treatments and large reduction (>99.94%) and strain that the ingot undergoes during production of the sheets completely destroys the original ingot structure and its inherent heterogeneity. However, the effects of ingot structure can, a priori, be deduced from the observed effects of constituent phase particle size, type and volume fraction on recrystallization, development of texture during annealing and deformation, and earing. In fact, careful examination of the behavior of products produced from different size ingots or castings have shown that the original microstructure of the ingot has a direct impact on the properties and performance of the end products."

Jan 1, 2011

By Clarence Karr

RESINS from a bituminous pitch, a bituminous coal, a lignite tar, a subbituminous pitch, and an electrode binder pitch wore investigated by the Bureau of Mines. The compositions of these resins were determined by four independent methods of structural detemination: (1) Molecular formula and ring analysis, including ring (2) infrared and ultraviolet spectra; (3) combined pyrolysis/gas chromatography, and (4) catalytic dehyrogenation followed by spectra and pyrolysis. The resin structure was correlated with coal structure, and it was concluded that pitch resins probably consist of essentially unaltered coal molecules carried over with the tar vapors in low-temperature carbonization.

Jan 1, 1966

By Shadia J. Ikhmayies

SnO2:F/CdS:In bilayers were produced by the spray pyrolysis technique on glass substrates. The structures were characterized by recording and investigating their transmittance curves, I-V plots, X-ray difractograms (XRD) and by observing their scanning electron microscope (SEM) images. From the I-V plots it was found that the SnO2:F forms an ohmic or quasi-ohmic contact with CdS:In. XRD patterns show the polycrystalline nature of the films and show that there is a small shift in the position of the (200) line of SnO2:F without the appearance of new peaks. The morphology of the structures are compared with those of SnO2:F alone and CdS:In alone on glass substrates.

Jan 1, 2009

By G. L. Peralta

Geothermal energy is an important source of power in more than 12 countries and is a potential source in 50 countries. However, the exploration and use of geothermal resources generate residues such as scale and sludge. The scale is from the steam distribution pipes while the sludge is from cooling ponds. These solids contain significant levels of elements which are of environmental importance notably, arsenic, sulfur, copper, zinc and lead that require safe treatment and disposal. The compositions, phases, textures, morphologies and size of scale and sludge particles have been studied by laser particle size analysis, light microscopy, scanning electron microscopy, X-ray microanalysis, and X-ray diffraction. In addition, their leachability was tested with protocol leaching procedures and sequential extractions. The detailed spatial relationships and speciation of the environmentally significant constituents have received particular emphasis. The information obtained is useful in understanding how the scale and sludge are formed, their leaching behavior if disposed of in a landfill and in developing appropriate treatment strategies.

Jan 1, 1994

By Justin Karl, Ali Gordon, James DeMarco, Yongho Sohn

"Aluminum metal-matrix composites are lightweight materials that have the potential to supplant steel in many applications. The current work helps to identify the parameters that confer maximal strength and ductility. Torsion tests were performed on the as-cast aluminum metal-matrix composite A359-SiCp-30% at a variety of temperatures and twist rates. Dependence of material properties on temperature and strain rate were identified from equivalent stress-strain curves constructed from the reduced data. Examination of the microstructure was performed on the as-cast material and on fracture surfaces. A temperature-and strain rate-dependent constitutive model was applied to simulation of the mechanical response of the torsion specimen. Trends in material properties corroborate and extend trends identified previously under tensile loading with regard to temperature and strain rate dependence. Shear properties of simulated specimens agree with properties obtained through experimentation.IntroductionAluminum metal-matrix composites (A1-MMCs) have become increasingly popu1ar in recent years. While unreinforced aluminum alloys have low densities and high ductilities, they are not suitable for many applications due to their lack of strength and stiffness. To provide added strength and stiffness while maintaining favorable densities, it has become common to reinforce aluminum alloys with silicon carbide in various forms, although usually the inclusions are in the form of whiskers or particles. The result is a composite material with superior specific strength and stiffness. While whisker-reinforced composites are expensive due to the necessity of processing by nonstandard techniques and have low transverse properties when rolled, particle reinforced Al-MMCs have transverse material property values almost as high as the longitudinal properties and are not as expensive to process as whisker-reinforced Al-MMCs [1]."

Jan 1, 2012

By Denise Cristina de O. Nascimento

Natural lignocellulosic fibers are increasingly being used as polymeric matrix composite reinforcement owing to economical and environmental advantages as renewable and biodegradable materials. Among these, the piassava fiber extracted from a palm tree native of South America stands as one of the most rigid with a potential to be used as composite reinforcement. Therefore, the present work investigates the notch toughness behavior, by Izod impact tests, of epoxy composites reinforced with up to 40 % in volume of continuous and aligned piassava fibers. It was found that the incorporation of piassava fibers results in significant increase in the impact energy of the composite. Scanning electron microscopy analysis showed that the nature of the piassava fiber interface with the epoxy matrix is the major responsible for the superior toughness of the composite.

Jan 1, 2009

By Leonardo Mota, Felipe Perissé Duarte Lopes, Marcelo Gomes da Silva, Sergio Neves Monteiro, Helion Vargas

"Natural fibers, as a class of material, are attracting the interest of engineering sectors owing to specific advantages such as comparatively reduced cost and lower density as well as environmental benefits associated with renewability and biodegradability. For industrial applications, thermal properties, among others, are required. These are major requirements, especially in the case of an insulating natural fiber. In the present work, thermal properties of the curaua were investigated by photothermal techniques, i.e., the open photoacoustic cell and a method based upon the monitoring of the temperature evolution as a function of time. This investigation, in tum, permitted to evaluate two important thermal properties: the thermal diffusivity and the specific heat capacity of the curaua fibers. Indirectly, by means of simple mathematical relations, the thermal conductivity was also obtained. The results were compared with other materials and characterize the curaua fiber as an efficient insulator.IntroductionMaterials are gaining attention in recent years owing to their benefits for the environment as compared to synthetics. Being biodegradable, yearly renewable and recyclable, the natural planted-based are considered fully sustainable [1]. In particular, their life-cycle, from growing to industrial processing, absorbs as much C02 as it is emitted and makes them neutral with respect to greenhouse gases responsible for global warming [2]. Typical examples of these environmentfriendly materials are the lignocellulosic fibers that have been used in simple items such as ropes, baskets, textile, modest roofing, etc, since the beginning of our civilization [3]. In the past few decades, these natural fibers have been extensively investigated [ 4-1 O] as a possible reinforcement phase of polymer composites in substitution for synthetic fibers. In fact, engineering application of lignocellulosic composites are today in the market, especially in the automobile industry [11-13]. Out of the hundreds available natural fibers, only part of them exhibits superior properties to be qualified for composite reinforcement."

Jan 1, 2011

By Helvio P. G. Santafé Jr., Ruben J. S. Rodriguez, Sergio N. Monteiro, Teresa E. Castillo

"The coir fiber extracted from the husk of the coconut fruits are worldwide available in tropical regions as a low cost lignocellulosic by-product for many applications including composite filler in automobile parts. Possible uses above room temperature require information on the thermal behavior of these coir fiber composites. Therefore, the objective of this work was to perform thermogravimetric, TGA and DTG, analysis on polyester matrix composites incorporated with different volume fractions of coir fiber. In general, it was found that thermal degradation associated with weight loss occurred in three stages. Changes were also observed in the DTG peaks that could be attributed to the coir fiber participation through the decomposition of its lignocellulosic structure.IntroductionThe development of new materials has always been motivated by the need of improved properties. This was the case of modem composites with combination of properties that surpass those of conventional monolithic metallic alloys, ceramic or polymers, from which composites are made. A typical example is the synthetic fiber reinforced composite with specific strength i. e, ultimate stress divided by density, higher than any other monolithic material. Today, however, our global society is concerned with serious environmental problems and thus demanding that new materials be developed with distinct characteristics. They are known as environmentally correct and are expected to be sustainable, which corresponds to the condition of being biodegradable, renewable, recyclable and neutral with respect to C02 emission, considered the main responsible for global warning [1]. Synthetic fiber composites cannot meet these requirements. Consequently, new composite reinforced with cellulose-based natural fiber are being developed [2-8] and are already replacing the synthetic ones in several engineering fields including the automobile industry [9-11]. These composites have additional advantages owing to the lignocellulosic fiber benefits of being diversified, abundant, less expensive, lighter and of societal interest [8]. In some cases even technical advantages such as non-abrasive effect to processing equipments and more flexibility exist in comparison to synthetic fibers."

Jan 1, 2011

By Constantino Capurro

For certain applications, coarse titanium nitride (TiN) precipitates can be deleterious for the final properties of the material. Hence, in order to better understand the mechanisms involved in the generation of these precipitates, a thorough characterization of the particles observed in steels with different titanium and nitrogen content was carried out. Samples from liquid steel (tundish), continuous casting billets and final product were evaluated using an Automatic Particle Analyzer (APA) coupled to a Scanning Electronic Microscope (SEM). The location, frequency, size distribution and composition of the different particles observed were assessed. While only few TiN precipitates were observed in liquid steel samples, the density of this type of particle significantly increased in the continuous casting billets samples. Particles ranging from 1 to 10 µm were mainly found in the interdendritic zones of the as-cast structure. The density of TiN particles observed in these samples did not change after re-heating and rolling operations. A model to predict TiN precipitation during solidification was developed. A reasonable agreement was found between model results and measured data. Results of this analysis confirmed that the precipitated fraction of TiN increases as the product of steel Ti and N contents rises.

Oct 30, 2017

Cement kiln dust (CKD) is a waste product generated at the rate of 4 to 12 million tons per year in the United States. The dust has considerable resource potential as a neutralizer for coal mine waste effluents and as a lime substitute in the agriculture and construction industries. However, little information has been published on the composition and characteristics of CKD, and a concern arose over the potential environmental effects of the waste when an analysis of a single sample from West Germany revealed lead and zinc concentrations of 5,620 µg/g and 16,200 µg/g, respectively. To assess the hazardous waste potential of CKD,

Jan 1, 1983

By Emily Sarver, August Greth, Cigdem Keles, Setareh Ghaychi Afrouz

The characterization of respirable dust on the basis of constituent fractions and particle sizes is increasingly of concern for evaluating exposure hazards. For high-resolution particle analysis, scanning electron microscopy with energy dispersive X-ray (SEM-EDX) can be an effective tool. However, it requires particles to be deposited on a smooth, uniform substrate such as a polycarbonate (PC) filter for optimal results. While direct sampling onto PC is possible, this is not the standard approach in many situations. For example, in coal mines, respirable dust samples have typically been collected onto polyvinyl chloride (PVC) filters because they are intended for gravimetric and/or infrared spectroscopy analysis. Such fibrous substrates are not ideal for SEM-EDX (or other microscopy), but an effective method to recover and redeposit the dust particles could render such samples suitable for the additional analysis. Here, we present a simple method and compare SEM-EDX results for paired samples analyzed directly on PC and following recovery from PVC and redeposition on PC. Both laboratorygenerated dust samples (n = 10 pairs) and field samples of respirable coal mine dust (n = 44 pairs) are included in this study. Although some changes in particle size distributions were observed between samples analyzed directly and those that were recovered and redeposited prior to analysis, the results indicate the dust recovery method generally yields a representative sample in terms of mineral constituents. That said, results also highlighted the effects of high particle loading density on individual particle analysis. Considering all sample pairs, those with similar loading density between the directly analyzed and recovered sample tended to exhibit similar mineralogy distributions. This was generally the case for the lab-generated sample pairs, and the Freeman-Halton exact test of independence indicated that the samples in just three (of 10) pairs were in disagreement in terms of their mineralogy distributions. On the other hand, for the field samples, the directly analyzed sample often had higher loading density than the recovered sample; and the Freeman-Halton test showed that 25 (of 44) pairs were in disagreement. However, the effect of possible particle agglomeration on the directly analyzed samples cannot be ruled out—and exploration of this factor was beyond the scope of the current study.

May 17, 2024

By R. Hogg

"The problems of sampling particulate materials, and of characterizing the distributions of particle size and composition are reviewed. Requirements for sampling from comminution systems are discussed and a simple formula is presented for estimating the minimum sample size needed. The limitations and errors associated with the techniques available for particle size analysis are evaluated and guidelines are suggested for the selection of appropriate methods. The use of microscopic and macroscopic approaches to the characterization of particle composition are discussed.INTRODUCTIONComminution is a process of particle size reduction in which the goal is to produce a material with a specified particle size distribution from a coarser feed. In mineral processing applications, the product size distribution is often qf secondary importance to the extent to which individual mineral grams can be liberated from one another. However, due to poor understanding of the nature of the liberation process and the lack of reliable procedures for characterizing it, the actual specification is normally in terms of particle size.Particle size distribution can be regarded as the fundamental characteristic of a particulate system. The distributions of particle shape and composition among the various particle sizes present are often sufficient to define the bulk properties and behavior of the system. Description of the distributions of size; shape and composition of the different phases which may exist within individual particles is necessary to complete the picture and is especially important for predicting liberation etc., in comminution processes. It is quite obvious that · the complete characterization of real particulate systems is a formidable, if not .impossible task. Practical characterization procedures should involve ·evaluation of those characteristics which are deemed to be important and which can be measured. In comminution systems, this should ideally include the particle size distribution, the size-by-size distributions of particle composition, and as much information as can be acquired on the internal composition and structure of individual particles. In most cases, of course, we fall far short of even this rather limited goal."

Jan 1, 1988

By C. J. Beyke

Slags and/or mattes from three secondary lead producers were studied as part of an effort to develop treatment methods for these lead-bearing residues. Each company used a somewhat different production process. Company A used a reverberatory furnace followed by a blast furnace. Company B used only a blast furnace. Company C used both a reverberatory and a blast furnace, and the scrap material was desulfurized with sodium carbonate prior to smelting. The slag matrix produced from sulfur-bearing scrap consisted mainly of iron-calcium silicates; the slag from desulfurized material was similar, but also contained sodium. In all the slags most lead was present in metallic form, often alloyed with tin, antimony, arsenic, and/or iron. Slag from Company B contained the most alloying elements, often as discrete subparticles within the lead droplets. Mattes were produced at Companies A and B; predominant phases were pyrrhotite and magnetite, while lead was present in metallic form and as galena.

Jan 1, 1995

By Jacob Petersen, Jon J. Kellar, Samuel Kessinger, Kiran Green

 The paper demonstrates that Belle Fourche Shale (BFS), an abundant shale, can be transformed into a ceramic through careful characterization and thermal processing. The study explores the potential of BFS ceramics for use as refractories and thermal energy-storage devices, highlighting their high thermal storage capacity, good thermal shock resistance, and cost-effectiveness.

Dec 1, 2023

By Jacob Petersen, Jon J. Kellar, Samuel Kessinger, Kiran Green

Belle Fourche Shale was processed and characterized for use as a clay-based ceramic. The shale was wet sieved to produce particles that were ± 150 μm. X-ray diffraction (XRD) revealed that the -150 μm material was enriched in clay content compared to the unprocessed materials, whereas the oversize material was enriched in quartz compared to the undersize sample. Particle size analysis was performed on the—150 μm sample, which showed that the median particle size was around 10 μm. Scanning electron microscopic (SEM) analysis further confirmed the small plate size, which appeared to be primarily layered clay particles. Next, the -150 μm particles were rolled into a green body, dried at room temperature, and fired at 998°C. The fired piece was analyzed by XRD and contained 6 wt% hematite, 55% quartz, 19% microcline, and various other minor amounts of minerals. When fired at 1152 ℃, mullite was found with increasing hematite compared to the 998 ℃ firing. A multi-spectral analyzer was used to quantify the color change of the 998 ℃ fired (orange) to the 1152 ℃ fired (red) samples. Micro-computed tomography (Micro-CT) of the unfired body exhibited very few large pores, while the piece fired at 998°C also exhibited few and small pores, the overall porosity of the fired body increased. Microhardness data, obtained from the aforementioned samples, resulted in Vickers Hardness (HV1.0) values of 70.8 HV1.0 (998 ℃) and 485.7 HV1.0 (1152 ℃). Three-point bend testing was performed, giving an average strength of 23 MPa on pieces fired at 998 ℃. The average bending strength of the samples fired at 1152 ℃, was 55 MPa.

Sep 26, 2023

By Luís Marcelo Tavares, Daniel Francioli, Malcolm Powell, Mohsen Yahyaei

"Mathematical modeling of the comminution process requires understanding of all breakage mechanisms occurring in this mechanical environment. Modeling of high energy impact breakage is well established, however, modeling low energy breakage including incremental damage breakage, attrition and abrasion is still under development. Free fall incremental impact tests were carried out to investigate the surface fragmentation of a copper-gold ore. This process was achieved by dropping particles individually from a height of four meters onto a metallic plate. The impact specific energy was 0.01KWh/t. The setting of the metallic plate was changed to test the impact angles of 0°, 45°, and 60°. Tests were carried out using fresh angular rocks as well as smoothed particles. Changes to the plate angle and particle shape enabled the study of the influence of the tangential component of the impact energy along with particle shape on superficial breakage. By studying the fractional mass loss variation in each impact, two distinct stages of surface fragmentation were clearly determined: high fractional mass loss dominated in the first 10 impacts and was attributed to chipping, whereas low fractional mass loss occurred for the remainder of the impacts and was attributed to abrasion. Smoothed particles demonstrated higher resistantance to breakage and their surface fragmentation behavior indicated a closer relationship to abrasion, especially when lower impact angles were used."

Jan 1, 2014

By Yuchen Wu, Jing Mei, GUOZHONG LIU, KE GAO, Songjie Tian, Jianwei Cheng, Yu Wang, Yuhang Wu, Hui Wang

The stability and integrity of protective coal pillars between the longwall working face and development roadways are greatly affected by the mining activities such as the development face advancing or retreat mining. Due to underground strata pressure, the coal pillar cracks could be further developed and then the air leakage passages (mainly cracks) could be produced greatly. The air circulation caused by the atmospheric pressure difference between the two sides of the coal pillar may also provide suitable conditions for the possible spontaneous combustion of the residual coal in the mine gob. In this paper, a typical the protective coal pillar in a Chinese coal mine is studied. The deformation and stress of coal pillars during the mining process of longwall working face are simulated by using FLAC3D. The displacement and strain of coal pillars are analyzed. Two indexes, the linear fracture rate (LFR) and area fracture rate (AFR), are introduced to characterize the development of internal cracks’ development within coal pillars. By using field measurement, the air leakage intensity distribution due to coal pillar cracks is obtained; the equation of air leakage resistance of coal pillar under the influence of mining is derived. Then, the possible location of large air leakage of coal pillar is determined, which can be used as guidelines to study the possibilities of coal spontaneous combustions happening in pillar or mine gob. The research results help to control such potential hazards in advance.

Jun 16, 2022

By L. Zhou, L. Yuan, D. Bahrami, Y. Xue

Underground mine accidents, such as mine fires, remain a health and safety risk to mine workers. Researchers at the National Institute for Occupational Safety and Health (NIOSH) are developing a data-driven, predictive model for characterizing the location and size of unknown underground fires. This study examines applying a machine learning-based model to predict fire size and location in a large underground metal mine based on hypothetical scenarios on the model performance. The results show that the size and location of an unknown fire can be determined with over 80% and 90% accuracy, respectively, and potentially help to reduce the risk of hazardous conditions for emergency response.

Feb 1, 2024

By Deirdre Bradshaw, Cornelius Vos

"The detailed understanding of the variability in process performance parameters within an ore body forms a key aspect of ensuring that proper decisions are made with regards to the economic viability of that ore body. To gain this understanding, various tools have been developed over the years, of which the batch flotation test is the most well-known and applied technique for investigating the flotation separation of ores. In this paper, the Julius Kruttschnitt Mineral Separability Indicator (JKMSI) is put forward as a small-scale test, suitable for the characterization of the flotation separability of copper porphyry ores. It is demonstrated that the JKMSI can be a complementary technique to the batch flotation test, with the capability to further improve the knowledge of ore body variability. The response from this test has been shown to be sensitive to particle size and modal mineralogy, providing a critical link between flotation and upstream comminution activities. The trade-off between the fineness of grind and the recovery target can thus be evaluated to determine the minimum energy application required for optimal separation economics. The test is designed to utilize small sample quantities of various sizes, providing an opportunity to increase our understanding of ore variability through increased tests. This complements our ore body knowledge and combining this with efforts in comminution (Powell, 2013) provides a platform for extending the concept of flexible circuit design."

Jan 1, 2014