Search Documents

By M. C. Chang, J. Dasher

The Crucible mine in Pennsylvania, operating on Pittsburgh seam coal, is rated at 5000 tpd. The washing plant, built in 1943, is rated at about 400 tph, using hydroseparator boxes to wash the coarse coal (4 x 5/16 in.) and hydrotator units for the fine coal (5/16 x 0). It is generally acknowledged that gravity concentration equipment cannot be used efficiently to bene-ficiate coal finer than about 65 mesh. Before the present flotation circuit was installed, Crucible recovered its fine coal slurry, predominantly —24 mesh material, by passing it through a battery of five 14-in. and one hundred and ten 3-in. Hey1 & Patterson cyclones in parallel with a 75-ft Dorr thickener. About two thirds went to the cyclones and one third to the thickener. Underflows from cyclones and thickener were filtered, respectively, in one 12-disk Eimco and two 4-disk Oliver filters fitted with stainless steel cloth. The resulting cakes were added to the coarse metallurgical coal. The filtrates, overflow from the 3-in. cyclones, and thickener overflow were recycled to the coarse coal plant. The three major problems encountered in this system became acute when the mine switched from track-mounted machinery to the more economical off-track equipment. The quality and uniformity of product declined, too much slime accumulated in the circuit, and waste pond disposal became highly impracticable. Lowering of Quality and Uniformity: Since the filter cake was not beneficiated in any way, addition of this material, which contained about 18 pct ash. would certainly lower the quality of metallurgical coal. Difficulties of handling the high-ash, high-moisture cake were compounded by the lack of adequate blending facilities at the mine, making it impossible to maintain uniform feed for the coke ovens. For a two-month test period, to verify the source of trouble, all filter cake was excluded from the metallurgical coal. The excluded filter cake was stocked in the yard. Slime Buildup: The moisture retained in the coarse coal products and the filter cake provided daily the only means of slime bleed from the circuit. As this bleed was not enough to offset the incoming fines in the raw coal feed, there was excessive buildup of slimes. To operate at all, it was necessary to purge the system each weekend by pumping all the solids from the thickener to a waste pond. The slimes built up during the week progressively increased the apparent viscosity and density of the circulating plant water, so that hydroseparators and hydrotator units had to be constantly adjusted. Uniformity, yield, and quality of the metallurgical coal suffered in consequence, and the filter cake ash and moisture contents increased from Monday to Friday. Limited Waste Disposal: Location of the plant does not permit unlimited waste pond area. Maintenance of a waste pond for the purpose of emptying the thickener during weekends became a costly burden that could not be tolerated. HOW THE PROBLEMS WERE SOLVED The flowsheet (Fig. 1) chosen to overcome these difficulties is considered the one most economical to install and operate. In a preliminary change made before the flotation circuit was installed, the cyclones and thickener were first operated in series, the overflow from the 3-in. cyclones, after flocculation, being discharged into the thickener and the thick-

Jan 1, 1960

By H. J. Modi, D. W. Fuerstenau

pH effectively regulates the flotation of corundum through its control of the surface charge. Since collector ions function as counter ions in the double layer, the collector must be anionic when corundum is positively charged and cationic when it is negatively charged. Even a long-chained xanthate will float positively charged corundum. Association of the hydrocarbon chains of the adsorbed collector ions gives rise to increased adsorption and increased rate of flotation. Because of this phenomenon, neutral organic molecules aid flotation although the unionized collector cannot promote flotation independently. Na2SO4 was found to depress the flotation of corundum with animic collectors through ionic competition whereas the same salt activates corundum for flotation with cationic collectors. A close connection between ion association, electrokinetic behavior, and floatability is suggested. As part of the increasing interest in the physical chemistry of flotation, strong experimental evidence has been obtained which indicates that organic ions are adsorbed as counter ions by non-metallic oxide minerals mainly because of the electrical forces which exist at interfaces(1-3). Thus flotation of such minerals without activation should then be appreciable only when the mineral and the collector are oppositely charged. Since only limited work has been reported on the effect of surface charge upon flotation behavior(3) this general hypothesis on the flotation of insoluble oxide minerals has not been tested thoroughly. Investigating the flotation of a mineral for which extensive electrokinetic data exist yields a way to test this hypothesis more extensively. The electrokinetic behavior of corundum in solutions containing both organic and inorganic electrolytes has been studied quite thoroughly' Electro-kinetic measurements have shown that in the case of corundum, simply by controlling pH the solid surface can be charged either positively or negatively. For this reason corundum was chosen for study. The object of this paper is to present a study of the flotation of corundum and to explain the results in the light of our knowledge of adsorption mechanisms gained from streaming potential investigations. This paper is concerned mainly with the effect of surface charge on flotation with anionic and cationic collectors, but in addition such flotation phenomena as collector hydrolysis, Van der Waals attraction between hydrocarbon chains, ionic competition, and activation are discussed. While the present paper is confined to a reporting of the data obtained and some of the more immediate conclusions, it will be seen that the results, in combination with those on other systems, do promise a

Jan 1, 1961

By F. M. Morris

A large reserve of thick coal in southwest Virginia was developed by Clinch-field Coal Co. in 1957-1958 to produce a nominal rate of 1500 tph raw coal. Operation features coal cleaning in transit. Refuse removed averages 35 pct. Evolution of plant from initial conception to completion is discussed, selection of means applied is explained, and performance to date us design expectation is described. The long-range plan calls for ultimate handling capacity of 40,000 tpd raw coal with anticipated clean coal capacity of 26,000 tpd on a three-shift basis. From a materials handling viewpoint, the Moss No. 3 operation is principally of interest as an ensemble. Generally speaking, it uses time-tested equipment and ideas but some of these are employed on a scale that may be new in the industry. At present about 20,000 tpd of raw coal are being handled. This is expected to increase to 40,000 tpd as soon as business conditions justify it. The purpose of this paper is to discuss the evolution of the plant as to materials handling practices, to describe briefly the equipment and methods used, and to comment on performance in certain areas. The subject divides itself naturally into four phases: 1) operations at the mines, 2) transportation from mines to plant, 3) raw coal handling into the plant, and 4) transportation of refuse away from the plant. OPERATIONS AT THE MINES The coal reserves for Moss 3 are in southwest Virginia where Dickenson, Russell, and Buchanan Counties come together. This area contains about 15 square miles and over 100,000,000 tons of coal. Here the No. 4 (Tiller) and No. 5 (Jawbone) seams of the Norton Formation lie so closely together that for practical purposes, they constitute one seam of coal. This seam, which is called the Thick Tiller, varies from 10 to 18 ft in thickness and underlies Sandy Ridge, a mountain cresting between 2400 and 3300 ft above sea-level. At 18-ft seam height (which is considered to be the maximum practical mining height) the parting between seams will be about 3 1/2 ft thick and each bench of coal will be about 7 ft thick. Depending on the amount of impurities in the seams Drover. total reject in this height coal may approximate 50 pet by wt. It will average about 35 pet for the property as a whole. The first move in developing this resource was made in 1953 when contour maps of several square miles around Duty, Va., including all the known outcrop, were made by photogrammetry. At this time, it was felt the prospective operation would be served by the Clinchfield Railroad and a photogrammetric route survey was made by this railroad from Haysi to Duty. Study of the resulting maps indicated only one site—adversely owned—which might accommodate the size washing plant to be erected. Water resources of a dependable nature seemed nonexistent. In 1954 bulk washability tests were made on the Tiller Bench at the Moss No. 1 preparation plant. The tests indicated this portion of the seam, mined separately, would wash to 4 pet ash with good recovery. Also in 1954, development of Moss No. 2, south of Sandy Ridge, was begun. This mine is in the Tiller Seam where it is about 100 ft below the Jawbone Seam. The reasons for developing a mine in the normal Tiller Seam before tackling the Thick Tiller seemed compelling: Railroad service could be established quickly, communications were better (though not good!), more was known of the seam (it had been mined in the years 1911 to 19241, and there was no essential property to be acquired. After some legal skirmishing, the Norfolk & Western Railroad was granted the right to serve the new mine. Three decades earlier the old mine had been served by the Clinchfield Railroad. The event which triggered active development of Moss 3 was the Appalachian Power Co.'s decision in 1956 to build a 450,000-kva power plant on Clinch River at Carbo. This solved the problem of marketing the steam coal which inevitably must be a product of a mine in the Thick Tiller. Management promptly decided to build the preparation plant at Carbo where an excellent site was owned; where railroad service existed; where telephone service could be obtained; and where roads, bridges, and water supply were tolerable.

Jan 1, 1961

By J. Peperakis

Coal mine bumps are normally associated with pillar mining under moderate or deep cover. Severe bumps at Sunnyside, however, have not been confined to pillar lines. Many have occurred in virgin development and in localities a long way from active pillar workings. As early as 1918 bumps in virgin territory were attributed to the faulted structure in the Sunnyside area.' Sunnyside is an old property, mined for more than 60 years. Both man-made and natural conditions contribute greatly to bump occurrences, and loss of life and great destruction of workings have resulted from some unusual bumps in recent years. Before Kaiser Steel acquired the Sunnyside Mines in 1950, about 21 million tons of coal had been extracted. Large areas had been worked out and equally large areas first-mined. As demand for coking coal gradually diminished, extensive blocks were shut down, and during the low production period of the 1930's mining on a very limited scale was confined to a section of the property close to the coal tipple. Following purchase of the property Kaiser Steel developed the mines into a fully modernized operation. The worked out and first mined areas covered about four square miles extending five miles along the strike and up to one and a half miles down dip from the outcrop. The sections with favorable mining conditions and clean coal had been largely extracted under the selective mining system imposed by economic conditions and the lack of cleaning plant facilities. Large reserves remained on the fringes of the worked out sections and in areas under deep cover and difficult roof. There were also considerable reserves in first-mined areas. In recent years much of Sunnyside's daily output of 7000 to 8000 tons has been derived from the partially mined localities. Many bumps have occurred when pillars have been pulled within the first-mined areas and on the fringes. The bumps have been associated with retreating pillar lines backing up against old workings and pillar lines in old first-mined areas backing up against highly stressed oversized barrier pillars surrounded by smaller pillars. In some parts of the property the upper Sunnyside seam was extensively worked in the past, and sizable areas of old works overlie the present lower seam workings. Abutment pressures from barrier pillars and pillar remnants are transmitted to the lower seam, contributing to bumps and squeeze conditions. Cover: The terrain is exceedingly rough, and cover varies considerably over relatively short horizontal distances. For example, at No. 1 mine the 2000-ft cover line is ony 2700 ft from the coal outcrop, and at No. 2 mine the cover over the main hoisting slope increases from 1000 to 2000 ft in a horizontal span of 1200 ft. Cover over the present mining sections ranges from several hundred feet in the valleys to 2500 ft under the crest of the divides. A short distance ahead of Sunnyside's deepest development down dip the cover reaches 3000 ft or more.

Jan 1, 1959

By G. G. Sarkar

SHARPNESS of separation and washing efficiency are often confused. The sharpness index indicates the precision of a washing unit; the washing efficiency takes into account not only the unit's precision but also the washability characteristics of raw coal and the near-gravity materials at the effective density of cut. A sound basis for evaluating the sharpness index is essential in comparing the sharpness of separation attained by different cleaning units. Sharpness Index and Related Criteria: Washing plant sharpness of separation has been well represented by Hancock's efficiency chart and Tromp's curve of migrated materials. Some useful coefficients derived from Tromp's curve—the error area, probable error, and imperfection value—have been widely used to measure sharpness of separation. These are defined in a number of papers presented at the first and second International Coal Preparation Colsference held in Paris (1950) and Essen (1954).1-5 In evaluating the performance of a dense medium separator at four different gravities, Yan-cey and Greer6 bserved that even with similar operating conditions and the same size grading of feed, the imperfection value of a washing plant varies through a greater range than the probable error. The present writer also observed the same type of anomalies in comparing the imperfection values of one plant which were determined under almost identical conditions. He therefore devised a graphical method to evaluate a washing unit's sharpness of separation and define it by a single coefficient, which is substantially independent of coal characteristics under normal operation of the unit. Unlike imperfection value, the new coefficient can be expressed on a percentage basis. Coal preparation engineers generally agree that the amount of misplaced material resulting from any separation in a washing plant is almost directly related to the amount of +0.10 sp gr (near-gravity) materials. In actual practice, however, misplacement is not restricted to the 20.10 sp gr range. It will be evident from a study of Tromp curves that this misplacement often extends over unequal specific gravity ranges on the two sides of the actual density of separation. The same condition exists for near-gravity ash distribution and the resultant misplacement of ash units during any separation. But so far as the same unit is concerned, the total misplacements bear a definite ratio to the amount of near-gravity zone materials that is affected by misplacements. This ratio should be constant not only for various densities of separation but also for different qualities of feed coal treated in the same plant. This ratio, multiplied by 100, directly represents the inefficiency of the plant. When the plant inefficiency value is subtracted from 100, the re- ' sult is designated as sharpness index. Evaluating the Sharpness Index: The method of evaluating the sharpness index is explained here with reference to Fig. 1. Fig. 1 is a reproduction of the familiar diagram used by Cerchar of France to represent the inefficiency of a separation in terms of "triangle of errors," which is a measure of organic loss. It will be observed that the characteristic (yield/fractional ash) curve of the raw coal represented by GHAPR

Jan 1, 1958

By R. Stefanko

The use of strain gauges and compression pads for an underground bolt installation in a central Pennsylvania coal mine revealed that satisfactory anchorage could not be maintained in the shale stratum that constituted the immediate roof. Comprehensive laboratory tests resulted in a new shell designed with an increased area of contact and smaller surface serrations. Retightening of the bolt was also found to be beneficial for maintenance of high load values. Roof bolting in coal mines has progressed very rapidly in the last decade, and today this method of support is in general use. There are many theories concerning the functions of roof bolts, but the importance of beam building is indisputable. Proper tension in the bolts minimizes shearing along bedding planes and creates a thick, competent beam from individually weak layers. Bolting must be accomplished immediately upon exposure of the roof, and bolt tension must be maintained if roof failure is to be prevented. Seams are being mined today with roof bolt support where conventional timbering was not effective.' The widespread use of continuous mining equipment was made possible by roof bolts which permit long supported spans free of obstructions. Since adequate anchorage is the key to successful bolting, better methods for determining the efficiency of anchorage are continually being sought. Attempts have been made to measure bolt loads, thus assessing anchorage efficiency by employing sensing devices between the bolt head and roof. 3-s None of the techniques appears to be very accurate, and all have at least one serious deficiency. The greatest efforts are being directed toward the standardization of the pull test.6" Nevertheless, the author believes that the pull test is only one criterion for establishing the efficiency of anchorage and not necessarily the most important one. The conventional pull test involves the short-term application of forces, whereas the success of roof bolt installations is dependent upon the ability of anchorage to sustain relatively long-term forces. Therefore, it would appear that the time-dependent function of the anchor is the single most important parameter for the success of roof bolting in many types of rocks. UNDERGROUND TESTS Strain gauges and compression pads were employed to measure bolt loads in a central Pennsylvania coal mine.8 Bolting had been employed only sporadically in the shale top since dubious benefits were obtained with this type of support. Table I shows some typical results from this investigation. Anchorage losses were extremely variable among the bolts, but all showed a considerable degree of bleed-off. The tests indicated that anchorage efficiency was extremely low in this type of shale. The results confirmed that bolting under these conditions was practically worthless, and thus a waste of material and labor. Probably even more important, bolting constituted a hazard when reliance was placed upon it for support. Certainly the complete lack of confidence in roof bolting, which was apparent in the mine personnel, was justifiable since the bolts did not accomplish their purpose. PRELIMINARY LABORATORY BOLT TESTS The extreme losses in bolt tension that were detected in underground installations prompted a comprehensive study to assess the causes. However, preliminary studies were first made to determine the combined stresses in a roof bolt and to prove conclusively that the observed bleed-off phenomena were due to anchorage: slippage and not to some other physical manifestation. In all of the ensuing tests

Jan 1, 1962

By A. F. Meger

Coal treatment by oil spraying receives special attention at the Georgetown plant for the dividends it pays in satisfying present customers and attracting new markets. Customer satisfaction requires care, quality control, and use of suitable oils. REPRESENTED here are the ideas and varied experiences of many people in the Hanna Coal CO. who have helped develop, over a number of years, an efficient and flexible method for spraying controlled amounts of oil on coal. Since the Georgetown preparation plant began operations early in 1951, oil treatment of coal has received special attention. It is believed that oil treating will satisfy present customers and also attract new markets. The first step in developing the new method of oil spraying was the construction of a dust cabinet for testing 50-lb samples of treated coal with the available oil sprays on the market. Tests results were tabulated for both indoor and outdoor storage. The graph, Fig. 1, shows results of the original tests made with a 700-sec residual blend and a 500-sec lubricating oil on Georgetown stoker coal of 1¼x3/8-in. size.* The advantages of better price, improperly blended can raise havoc. Some.,pale oils also, although odorless when delivered, give off a sweet sickening odor when atomized under pressure. It is recommended that all products be tested before they are used. There is a specific place for all spraying oils. For example, at a power plant a severe dust condition exists around the stockpile area and in parts of the plant. The cheapest spraying oil made, regardless of odor, will do an excellent job in this case and will save the company 3 to 5c per gal or more. Domestic trade, on the other hand, must be carefully handled to prevent complaints about odor, and the only way to do this is to stay with the proved products after the odor tests have been made. The preparation plant at Georgetown has facilities to handle either tank car or tank truck deliveries. Steam is available at the unloading point if the weather is severe, and there is an indicator at the unloading point to prevent overflowing the 20,000-gal underground storage tank. Systematic test samples are removed from each delivery and sent to the lubrication engineer to insure quality control. Fig. 3 illustrates the chutes in which smaller sizes of coal are treated. Fig. 4 shows the entire spraying system. Buried in the ground is a 20,000-gal tank with immersion heaters grouped around the feeder line to insure adequate gravity flow to the pump under all conditions of weather. Oil flows to a 500-gal preheating tank where the temperature is kept about 150°F by six 1½-kw immersion heaters thermostatically controlled. Hot oil is fed through a self-cleaning disc-type filter to the hydraulic pump. Valves and piping make it possible to transfer oil from one tank to another or to drain the lines for maintenance purposes. All this equipment is below ground level in a covered pump room,

Jan 1, 1955

By Orville R. Lyons, A. C. Richardson

THE Coal Division of Battelle Memorial Institute, during the course of an investigation conducted for a coal producer, carried out extensive sampling of the fine-coal section of a preparation plant. The information obtained during the testing period was used to evaluate the overall plant operation and provided the basis for. recommended changes in the plant flowsheet. Included in the information were data for the results obtained when using a Bird centrifuge to dewater the particular coal being treated. At the completion of the investigation, the coal producer gave Battelle permission to publish the operating data for the Bird centrifuge in order to make this information available to the coal industry. The authors wish to take this opportunity to express their appreciation to this company and its officials for their willing cooperation in the matter of publication. Description of Preparation Plant: The preparation plant on which the data were obtained is primarily a jig plant. The coal being washed is a low inherent moisture, friable, Pocahontus-type. The washed coal from the jig is dewatered and sized at 1/4 in. by a Parrish-type dewatering and sizing screen. The minus 1/4-in. coal and the underflow water from the shaker screen flow to a sludge tank where, after the coal settles, the coal is conveyed by a flight conveyor into a pump sump. The pump, a 300-gpm sand pump, delivers a mixture of fine coal and water to a Bird centrifuge which produces a dewatered cake and an effluent. At the time when the investigation was made, the centrifuge effluent was returned to the sludge tank and the cake product was mixed with a coarser size of coal prior to loading into railroad cars. The semiclarified water from the sludge tank overflowed into a pump sump from which it was pumped to the jig. As originally designed, the preparation plant was intended to operate with a closed water system but it was found, soon after operations started, that for various reasons this could not be done. In order to provide for removal of excess water from the system and to aid in maintaining the desired minimum percentage of solids in the circulating water, the plant was operated to provide from the sludge tank a continuous overflow of water and fine solids that was sent to waste. The centrifuge feed represents approximately 35 tons per hour of minus 1/4-in. coal in the form of a pulp averaging 38 pct solids. Sampling Procedure: In order to obtain basic data for determining the relationships existing in the fine-coal section of the preparation plant, samples were obtained for: (1) the centrifuge feed, (2) the centrifuge cake, (3) the centrifuge effluent, and (4) the circulating water. The sampling was arranged to start on a Monday, in order to begin operations with a sludge tank full of fresh water, and was continued long enough to allow sufficient time for fine solids to build up within the water system or for a two-day, four-shift operating period. All samples were taken at half-hour intervals except when plant stoppages occurred. After a stoppage the plant was

Jan 1, 1951

By Orville R. Lyons, A. C. Richardson

THE Coal Division of Battelle Memorial Institute, during the course of an investigation conducted for a coal producer, carried out extensive sampling of the fine-coal section of a preparation plant. The information obtained during the testing period was used to evaluate the overall plant operation and provided the basis for. recommended changes in the plant flowsheet. Included in the information were data for the results obtained when using a Bird centrifuge to dewater the particular coal being treated. At the completion of the investigation, the coal producer gave Battelle permission to publish the operating data for the Bird centrifuge in order to make this information available to the coal industry. The authors wish to take this opportunity to express their appreciation to this company and its officials for their willing cooperation in the matter of publication. Description of Preparation Plant: The preparation plant on which the data were obtained is primarily a jig plant. The coal being washed is a low inherent moisture, friable, Pocahontus-type. The washed coal from the jig is dewatered and sized at 1/4 in. by a Parrish-type dewatering and sizing screen. The minus 1/4-in. coal and the underflow water from the shaker screen flow to a sludge tank where, after the coal settles, the coal is conveyed by a flight conveyor into a pump sump. The pump, a 300-gpm sand pump, delivers a mixture of fine coal and water to a Bird centrifuge which produces a dewatered cake and an effluent. At the time when the investigation was made, the centrifuge effluent was returned to the sludge tank and the cake product was mixed with a coarser size of coal prior to loading into railroad cars. The semiclarified water from the sludge tank overflowed into a pump sump from which it was pumped to the jig. As originally designed, the preparation plant was intended to operate with a closed water system but it was found, soon after operations started, that for various reasons this could not be done. In order to provide for removal of excess water from the system and to aid in maintaining the desired minimum percentage of solids in the circulating water, the plant was operated to provide from the sludge tank a continuous overflow of water and fine solids that was sent to waste. The centrifuge feed represents approximately 35 tons per hour of minus 1/4-in. coal in the form of a pulp averaging 38 pct solids. Sampling Procedure: In order to obtain basic data for determining the relationships existing in the fine-coal section of the preparation plant, samples were obtained for: (1) the centrifuge feed, (2) the centrifuge cake, (3) the centrifuge effluent, and (4) the circulating water. The sampling was arranged to start on a Monday, in order to begin operations with a sludge tank full of fresh water, and was continued long enough to allow sufficient time for fine solids to build up within the water system or for a two-day, four-shift operating period. All samples were taken at half-hour intervals except when plant stoppages occurred. After a stoppage the plant was

Jan 1, 1951

By Orville R. Lyons, A. C. Richardson

F. X. Ferney—We are pleased that this paper was presented at this meeting and thank Mr. Richardson and Mr. Lyons for their effort and work in preparing it. We agree with the authors that it was unfortunate that more comprehensive data were not available when the paper was prepared, this being particularly true since we had no knowledge that the paper was being written and could not make available data which were in our process files. Further, it is our opinion that because the data are not sufficiently comprehensive the results which are presented are erratic and will lead to false conclusions. As we see it, there are three Specific reasons why the data which are presented cannot be considered accurate. 1. The preparation plant was not at equilibrium while the samples were being taken. This is indicated by the fact that the percent of solids in the circulating water varied from 3.9 pct to 10.7 pct during the period when the plant was sampled. 2. We do not believe that the samples of Bird feed which were taken were representative and could indicatc the true feed to the filter. Evidence of this is shown in the data where the dewatered product leaving the centrifuge contains more coarse material than the feed to it, that is, material which is +6-mesh in size. 3. We question if the data concerning screen analysis in the fine sizes is accurate and would conclude (from the data) that these tests were made by a dry-screen method. We have found that wet screening is always necessary to obtain a true picture of the quantity of —200-mesh fines which is present. The test work described in the Lyons-Richardson paper was conducted some time ago and the tests were carried on during a period when the preparation plant had not ironed out all of their start-up problems. Since that time most of these problems have been corrected and now this is a smooth running, well-operated prep-

Jan 1, 1951

By Orville R. Lyons, A. C. Richardson

F. X. Ferney—We are pleased that this paper was presented at this meeting and thank Mr. Richardson and Mr. Lyons for their effort and work in preparing it. We agree with the authors that it was unfortunate that more comprehensive data were not available when the paper was prepared, this being particularly true since we had no knowledge that the paper was being written and could not make available data which were in our process files. Further, it is our opinion that because the data are not sufficiently comprehensive the results which are presented are erratic and will lead to false conclusions. As we see it, there are three Specific reasons why the data which are presented cannot be considered accurate. 1. The preparation plant was not at equilibrium while the samples were being taken. This is indicated by the fact that the percent of solids in the circulating water varied from 3.9 pct to 10.7 pct during the period when the plant was sampled. 2. We do not believe that the samples of Bird feed which were taken were representative and could indicatc the true feed to the filter. Evidence of this is shown in the data where the dewatered product leaving the centrifuge contains more coarse material than the feed to it, that is, material which is +6-mesh in size. 3. We question if the data concerning screen analysis in the fine sizes is accurate and would conclude (from the data) that these tests were made by a dry-screen method. We have found that wet screening is always necessary to obtain a true picture of the quantity of —200-mesh fines which is present. The test work described in the Lyons-Richardson paper was conducted some time ago and the tests were carried on during a period when the preparation plant had not ironed out all of their start-up problems. Since that time most of these problems have been corrected and now this is a smooth running, well-operated prep-

Jan 1, 1951

When a thin film of volatile matter is deposited under vacuum on a polished coal surface, and the coated surface is examined microscopically in piano--polarized reflected light, colour changes are observed characteristic of the various macerals present. The colour changes appear to be mainly due to interference between light reflected at the upper surface of the film and at the film/coal interface. A variety of source materials for the volatile matter required have been tested, including powdered bituminous coal, coal tars, boron oxide, and certain resins.

Jan 1, 1969

By Johnson M. W

Factual data about the sedimentation in the Newcastle Coal. Measures are presented. Data concerning the total coal measure sequence (isopachs, sand /shale ratio and total coal thickness variation), data about three coal seams (Borehole, Dudley and Victoria Tunnel) and data about interseam con- glomerate units are discussed. From this data conclusions are drawn about the coal measure environment. The western edge of the coal basin, the Lochinvar Dome, although a high feature was apparently stable during coal measure time. Despite its height it apparently supplied little sediment to the basin. The northern and north-eastern edge, which was unstable, suppl- ied most of the coarse detritus including the conglomerates to the basin. The conglomerates show patterns of fluvial origin but after a period of "normal" variations in pattern they become restricted to two parallel zones evidently tectonically controlled. Deposition of conglomerates is episodic and separated by periods of coal formation when deformation was apparently slight. Formation of each of the three seams considered followed a rather similar pattern - each shows development of thick coal around the basin edge and poor thin coal in the "axial" region of the present synclinal structure. Evidence of in-situ formation of some areas of the seams is discussed and periodic deformation of the basin during coal measure time is postulated.

Jan 1, 1969

By R. C. Neavel

One of the most important requirements to be met by any coal producer is delivery of size consists tailored to specific applications. Generally these specifications include a minimum as well as a maximum size limit. The customers of a major Indiana coal producer noticed that some shipments of sized coal contained a large proportion of undersize pieces. Also, in these shipments, the pieces which remained within the specified limits were cracked and, when handled, crumbled readily. The producer, certain that these shipments had been properly sized at the tipple, suspected that degradation had occurred in transit. The Indiana Geological Survey was requested to examine the coal from one of these shipments to attempt to determine the cause of breakage. Two basic facts about coal and coal seams led to the employment of petrographic techniques in this investigation. First, all coal seams consist of accumulations of diverse organic and inorganic constituents; and second, most coal breakage, either desirable or undesirable, can be attributed to the inherent weakness of some of these constituents or to poor adhesion between certain constituents. Analyses of degraded coal Sampling: Samples were secured from 2 stock piles of 2-by 4-inch coal in a dealer's yard. The coal in both piles had received the same treatment from mining to storage, although it had been mined and shipped on two different days. The size consist of one pile, however, appeared smaller than that of the other. The sample from the degraded pile is referred to as the slack sample, and the other is called the unslack sample. Size analyses: In order to determine the actual size consist, the samples were screened, with a minimum of rough handling, on square 2-inch, 1-inch, 1/2-inch, and 12-mesh screens. It is assumed that 100 percent of the 2-by 4-inch coal is retained on a 2-inch round screen at the tipple. Analyses of several loads at the tipple indicate that approximately 26 percent of the 2- by 4-inch coal, 100 percent of which was assumed held on a 2-inch round screen, passed through a 2-inch square screen. Twenty-six percent may be taken as the normal difference between round and square screens. Results of the analyses of stockpile coal are shown in Table 1. Cumulative percent versus size are plotted on a Rosin-Rammler chart as Figure 1. Both samples approximately follow normal size distribution; this indicates that breakage is not size preferential and also that the samples are representative of the stockpiles. Although both samples exhibit the same general size distribution, the median size of the slack sample is considerably smaller than that of the unslack sample. Fifty-five percent of the unslack sample was undersize (29 percent greater than the normal 26 percent difference), and 83 percent of the slack sample was undersize (57 percent greater than the normal 26 percent difference). Both piles contained a greater percentage than normal of undersize coal; this indicates that they were both affected by degradation, but to a different degree. Bedding-plane analyses: Coal, because of its laminated nature, will break preferentially along bedding planes, especially where adjacent constituents are poorly cemented to each other. Subsequent breakage perpendicular to the

Jan 1, 1961

By J. M. Schopt

COAL petrology is the study of the lithologic composition and texture of coal and includes megascopic as well as microscopic differentiation. Coal petrography is a quantitative study, principally (but not exclusively) microscopical in nature. The distinction between coal petrologic and coal petro-graphic studies usually is not important, but it is important to recognize that these studies differ materially from other types of petrology that deal primarily with minerals. The petrologic entities* of coal are less clearly distinguished than most minerals and the basis of distinction is not always clearly expressed. The relation of coal petrology to geologic, mining, and technologic problems is most evident when results of coal petrologic studies can be stated quantitatively. The chemical and physical composition of coal and the determination of its quality and properties are continuing problems. The source of these problems lies in the heterogeneity of coal and in its almost complete insolubility in ordinary solvents at normal temperatures. The empirical and comparative character of standard chemical coal analytic values is one of the consequences resulting from heterogeneity and insolubility of coal. Nevertheless, these coal analytic methods are highly technical and diversified. Coal petrol.ogy employs a group of similar analytical methods which provide information about coal that the other methods cannot supply. The heterogeneity of coal is most clearly demonstrated by means of petrologic studies. The properties utilized in coal petrologic studies are related to texture (size, form, and association), hardness, light reflectance, and light absorption and transmission (color). Size relations are most evident but are commonly overlooked. Coal is classed chemically as a mixture, and chemical analyses thus show the composition of the sample as a whole. Geologically coal is an organic clastic deposit, derived from diverse plant fragments and particles having a size range comparable to that of a conglomerate or breccia. The mixture of different materials that compose coal, large and small, can be realized only by microscopic study. This is because the fundamental cellular units of plants, from which coal is formed, are microscopic in size. The kinds of altered plant particles and fragments in coal have specific differences in hardness, reflectance, and color that signify differences in composition. These differences must be taken into account in evaluating the aggregate properties of coal. Terminology and Texture Full discussion of terms applied by various petro-logists in analysis of coal is beyond the scope of this article. For convenience the simpler types of petrologic entities that are defined without reference to lithologic occurrence or texture will be called coal components. Fig. 1 lists reactive and relatively inert

Jan 1, 1957

By W. E. Hess

AT the Vesta mines of Jones & Laughlin Steel Corp. on the Monongahela River, 35 miles south of Pittsburgh, JCM Joy continuous miners and 6-SC shuttle cars are used for pillar extraction in the Pittsburgh seam. The entire output of the mine goes into coke production for blast furnace operation. Because this coal, which has high metallurgical qualities, is close to the place where it is ultimately used and because supplies with these properties are being rapidly depleted, complete recovery is essential wherever possible. With the introduction of the continuous miner into the Vesta mines, therefore, it was necessary to plan a project which would facilitate development and provide for future total recovery. Use of continuous miners under varying conditions has necessitated changes with regard to roof action, method of development, method of pillar attack, and innovations in mining. In the following pages these changes will be discussed. Prior to the introduction of continuous miners the Pittsburgh seam at the Vesta mines averaged 72 in. of mineable coal, overlain with 12 to 16 in. of draw-slate, which weathers on exposure to air and is not firm enough to be held in place. Immediately overlying the drawslate is a wild or rooster coal, very irregular in thickness, varying from 12 to 30 in. Above the rooster coal the strata consists predominately of shales or lime shales and sandstone. Just before the introduction of continuous miners in the Vesta mines, however, a definite change took place in the character of the roof structure overlying the coal seam, see Fig. 1. Thickness of laminated roof immediately overlying the rooster coal varies with localities and introduces a problem in roof control. In fact, a set of eight main entries being developed in Vesta NO. 4 mine entered an area with so difficult a roof structure that management considered abandoning the section altogether. In this locality the roof consisted of thin alternate layers of roof coals and shales, with an occasional irregular seam of slick slate, the whole being laced with slips, and the coal itself being cut by clay veins and spars. In an effort to overcome some of the difficulties, roof bolting was introduced in 1949. This made it possible to recover coal from an area which otherwise would have been economically unmineable. There have been very few roof bolt failures. When conventional machines were replaced by continuous miners there were changes in the development of butt entries. By these changes it was hoped: 1—to speed development, 2—to provide as much solid coal as possible for the machine on retreat, 3—to avoid the necessity of crossing entries already driven, 4—to facilitate ventilation, 5—to provide a roadway for shuttle car haulage which would eliminate the necessity of running through doors or curtains, 6—to provide better roof control by increasing the distance between the center lines of entries, and 7—to provide more coal when the machine was in position to load.

Jan 1, 1956

By Fredrick C. Pearson, Albert Brown, Emil R. Ermert

EARLY in 1946 the Shen-Penn Production CO., a subsidiary of the Philadelphia and Reading Coal and Iron Co., was organized to operate the Shenan-doah Stripping, one of the largest open-pit anthracite mines in the world. This mine is located in the Western Middle Field near Shenandoah, Schuylkill County, Pa., and involves the removal of approximately 60,400,000 cu yd of overburden to permit the recovery of 9,200,000 gross tons of rough cleaned coal from an area 8000 ft long and 2700 ft wide, with a maximum depth of 400 ft. Operations began in August 1946, and within the next few years 31,811,-000 cu yd of overburden and 2,994,000 gross tons of rough cleaned coal had been removed. During the early days of open-pit mining operations, steam was the primary motive power. However, as the size of the equipment increased, so did the problems of fuel, water, labor, and maintenance. Because of its efficiency and convenience, electric power rapidly replaced steam. Later the modern diesel engine was developed, and today practically all stripping equipment is either electric, diesel-electric, or diesel-powered. In locations where electric power is not readily available or where operations are scattered over a large area, diesel power is favored. At Shenandoah operations are highly concentrated in a relatively small area, and this fact, coupled with the availability of ample electric energy, indicated the selection of electric-powered equipment. Since this was a new company, it was necessary to purchase every item, from the smallest tools to stripping shovels. Although the organization period was hampered by the postwar scarcity of materials, an excellent opportunity was afforded to set up a thoroughly modern plant. This paper will describe the power facilities, with particular emphasis on the more unusual features. The substation is a major item in a power distribution system, and a simple arrangement utilizing high quality equipment is an excellent investment. With this in mind, a 3000-kva unit type substation was selected and installed. This unit is made up of three sections, which are assembled simply by bolting together the various sections and connecting the power leads, see Fig. 1. The transformer proper, rated at 3000 kva, is oil-filled and nitrogen-sealed, having a 66,000-v Delta primary and 4160-v Wye secondary with a grounded neutral and 46-ohm ground resistor. The function of this resistor will be described later. Electrical energy is purchased from a public utility and is delivered to the main substation at 66,000 v over one or the other of two incoming lines. These lines terminate on a high voltage switching section on which high voltage fuses and Thyrite lightning arresters are installed. The outgoing feeder switching unit is made up of the following: 1—An auxiliary compartment consisting of potential and current transformers with necessary terminal blocks for connecting to power company metering equipment. 2—Another auxiliary compartment containing a control transformer, battery, and battery charger for the furnishing of power for tripping and reclosing of power circuit breakers. The assemblies in these auxiliary compartments are mounted on carriages that can be rolled in and out with ease. Potential transformers are readily accessible for inspection and fuse replacement. When withdrawn from the operating position they are completely de-energized and grounded. 3—Two feeder breaker compartments, each with a 1200-amp, 5000-v, solenoid-operated magneblast air circuit breaker, voltmeter, ammeter, overcurrent relays, and a ground relay. These power circuit breakers can be quickly and safely withdrawn or repaired. A built-in isolating mechanism is used for lowering the breaker to a transfer truck for repair or inspection or as a means of disconnecting the breaker from the source of power as an added precaution when working on power lines. Thus inspec-

Jan 1, 1953

By Albert Brown, Emil R. Ermert, Fredrick C. Pearson

EARLY in 1946 the Shen-Penn Production CO., a subsidiary of the Philadelphia and Reading Coal and Iron Co., was organized to operate the Shenan-doah Stripping, one of the largest open-pit anthracite mines in the world. This mine is located in the Western Middle Field near Shenandoah, Schuylkill County, Pa., and involves the removal of approximately 60,400,000 cu yd of overburden to permit the recovery of 9,200,000 gross tons of rough cleaned coal from an area 8000 ft long and 2700 ft wide, with a maximum depth of 400 ft. Operations began in August 1946, and within the next few years 31,811,-000 cu yd of overburden and 2,994,000 gross tons of rough cleaned coal had been removed. During the early days of open-pit mining operations, steam was the primary motive power. However, as the size of the equipment increased, so did the problems of fuel, water, labor, and maintenance. Because of its efficiency and convenience, electric power rapidly replaced steam. Later the modern diesel engine was developed, and today practically all stripping equipment is either electric, diesel-electric, or diesel-powered. In locations where electric power is not readily available or where operations are scattered over a large area, diesel power is favored. At Shenandoah operations are highly concentrated in a relatively small area, and this fact, coupled with the availability of ample electric energy, indicated the selection of electric-powered equipment. Since this was a new company, it was necessary to purchase every item, from the smallest tools to stripping shovels. Although the organization period was hampered by the postwar scarcity of materials, an excellent opportunity was afforded to set up a thoroughly modern plant. This paper will describe the power facilities, with particular emphasis on the more unusual features. The substation is a major item in a power distribution system, and a simple arrangement utilizing high quality equipment is an excellent investment. With this in mind, a 3000-kva unit type substation was selected and installed. This unit is made up of three sections, which are assembled simply by bolting together the various sections and connecting the power leads, see Fig. 1. The transformer proper, rated at 3000 kva, is oil-filled and nitrogen-sealed, having a 66,000-v Delta primary and 4160-v Wye secondary with a grounded neutral and 46-ohm ground resistor. The function of this resistor will be described later. Electrical energy is purchased from a public utility and is delivered to the main substation at 66,000 v over one or the other of two incoming lines. These lines terminate on a high voltage switching section on which high voltage fuses and Thyrite lightning arresters are installed. The outgoing feeder switching unit is made up of the following: 1—An auxiliary compartment consisting of potential and current transformers with necessary terminal blocks for connecting to power company metering equipment. 2—Another auxiliary compartment containing a control transformer, battery, and battery charger for the furnishing of power for tripping and reclosing of power circuit breakers. The assemblies in these auxiliary compartments are mounted on carriages that can be rolled in and out with ease. Potential transformers are readily accessible for inspection and fuse replacement. When withdrawn from the operating position they are completely de-energized and grounded. 3—Two feeder breaker compartments, each with a 1200-amp, 5000-v, solenoid-operated magneblast air circuit breaker, voltmeter, ammeter, overcurrent relays, and a ground relay. These power circuit breakers can be quickly and safely withdrawn or repaired. A built-in isolating mechanism is used for lowering the breaker to a transfer truck for repair or inspection or as a means of disconnecting the breaker from the source of power as an added precaution when working on power lines. Thus inspec-

Jan 1, 1953

By G. C. Gambs

The electric utility industry is the largest customer of the coal industry and consumes nearly 50% of the present coal production in the United States. The byproduct of the burning of coal in utilities is ash in several forms including fly ash, bottom ash and bottom slag. At present, very little of the coal ash produced is being used and must be disposed of as waste. The coal industry should look upon this waste material as a valuable by-product which, if it can be sold for $2 to $4 per ton, will have the net effect of reducing the cost of coal to the utility by 1¢ to 2¢ per million Btu. There are many ways to use coal ash and thus benefit both the coal industry and the electric utility industry by reducing the cost of coal as burned. The solutions to the problems are obvious and all we have to do is apply them. The electric utility industry is the largest customer of the United States coal industry, consuming nearly 50% of present coal production. By 1980, the electric utilities are expected to burn over 500 million tpy of coal or 75% of total coal production. When coal is burned in electric utility plants, ash is produced in one of several forms. These include fly ash, bottom ash and bottom slag. At the present time, approximately 20 million tons of these ashes are produced and must be disposed of by the utilities at a cost of 50¢ to $2 per ton. In 15 years, more than double this quantity will be produced. Only a small quantity of this ash is put to any practical use. Much remains to be done about expanding uses for fly ash and bottom slag. It is well known that fly ash, when used to replace a portion of the cement in a concrete mix, will produce highest quality concrete. The Corps of Engineers and the Bureau of Reclamation have constructed dams and other concrete structures for years with fly ash as a partial replacement for cement. However, many construction firms do not use it. This can become an opportunity for the coal industry to reduce the cost of coal delivered to utilities. Any fly ash, or other ash or slag, which is sold by the utilities, reduces the cost of coal burned by the utility. As much as 1¢ to 2¢ per million Btu could be taken from the fuel cost for each ton of ash sold which otherwise must be disposed of at a cost.

Jan 1, 1967

By Edwin B. Wilson, Joseph W. Leonard, Richard W. Borio

preparation of specification coals for the utility industry is approached from the standpoint of a cooperative effort with the power company to assure that the shipped product will be a noncorrosive coal. Selective mining, coal preparation, the use of additives, and coal blending are mine-site techniques proposed as means for upgrading corrosion-retarding constituents of utility coals (CaO and MgO) while, at the same time, reducing the concentration of those constituents of coal (Na20 and K,O) which cause corrosion. Data obtained from large-scale boiler testing in combination with bench-scale physical and chemical tests are used as a basis for the formulation of mine-site procedures to improve coal combustion utilization. Electric power generation remains the greatest market for coal in the United States. A major reason for this strong market has been the ability of the coal industry to supply a superior product for combustion while maintaining competitive prices. Now that the coal industry is engaged in intensive competition with nuclear power for future energy demand, it becomes ever more imperative that superior coal products are produced. One important problem when burning some coals is a liquid phase corrosive attack on boiler tube metal in the superheater and reheater areas of the furnace where steam temperatures may exceed 1050°F. In addition to causing power outages and high maintenance costs, corrosion is a continuing barrier to the future development of more efficient steam cycles which permit lower generation costs when using coal. Research methods of the past which have been directed at finding solutions which could be applied at the power plant site have been only partially successful and are generally costly. This paper contains a suggested --method of corrosion control through investigation of the problem at the source of the trouble—the coal supplier facility. It is proposed that mine-site pre-ventative procedures be considered as an effective means of cooperative corrosion control between the power company and the coal supplier. Economic justification must be applied to the individual situation. This paper is based on recent work by Combustion Engineering, Inc. and the Coal Research Bureau of West Virginia University under a contract from the Department of the Interior Office of Coal Research.',' Results which are of importance to this discussion may be summarized as follows: 1) The alkali minerals of coal (Na2O and K2O), as measured by an acid leaching process, can be related to corrosion rate in utility boilers. As these constituents increase in a coal product, its corrosiveness can be expected to worsen. 2) The alkaline-earth minerals contained in coal, reported as total CaO and MgO reduce corrosiveness 2s their concentration increases. 3) Naturally occuring, alkaline-earth-bearing materials, such as limestone and dolomite, may be added to a coal to reduce its corrosiveness. 4) Coals with very low iron contents tend to be less corrosive. These results provide the groundwork for examination of the system of operations which occur at the supplier facility from the seam face where mining is begun to the point of loading for shipment. The Mining System Fig. 1 is a cross section of one of the typical coal seams (designated coal A) that was boiler tested during this research program. This seam is overlain by material which consists primarily of a gray-black shale. In the lower third of this seam, there exists a thin rock parting of less than 4 in. in thickness which is consistent throughout the seam. The floor material is fireclay. In order to examine mineral distribution throughout this particular seam, the Coal Research Bureau collected a

Jan 1, 1971