Search Documents

By Qingchun Yu, Bin Yang, Yong Deng, Heng Xiong, Fei Wang, Minxiu Chen

"Metal aluminum produced by non-electrolysis process received much attention due to its lower energy consumption. In this paper, carbothermic reduction and carbothermic-chlorination of alumina in normal pressure and vacuum were studied. The products were examined by means of XRD, EDS and SEM. During the carbothermic reduction process using carbon reductant in normal pressure, no metal aluminum was found. However, when coal was used as reductant, a mixture containing metallic aluminum, A14C3, and silicon was obtained, but metallic aluminum couldn't be separated from the mixture. During the carbothermic-chlorination process in vacuum, Al404C and Al4C3 were produced by the reaction between alumina and carbon, and Al Ch gas reacted with Al404C and Al4C3 to produce Al Cl gas. Metallic aluminum was produced due to the disproportionation of A!Cl gas and condensed on the collecting plate. Meanwhile, the initial temperature of carbothermic reduction of alumina reduced in vacuum compared with that in normal pressure.IntroductionIndustrial production of primary aluminum is carried out in alumina cell by the so-called Hall- Heroult process, necessitating the use of very high currents of low voltage. The alumina from which metallic aluminum is gained must be chemically pure, otherwise impure metal results. The main drawbacks of the electrolytic production are its very high energy consumption, the release ofperfluorocarbons, and the high specific C02 emissions [1]. During the past years, there were a lot of attempts to produce metallic aluminum by carbothermic reduction of A1203 [2, 3]. Cox [4] determined the vapor pressure over the A1203-C system and performed X-ray diffraction analysis of condensed products. It was demonstrated that an increase in the carbon content in the system leaded to the sequence of transitions: A1203~Al404C~A1zoc~A14C3 ~AI [5]. In any carbothermic reduction process for aluminum, extremely high temperatures (2000 °C ) were required [6]. In spite of considerable effort, the carbothermic reduction of alumina to aluminum remains a formidable technical challenge, due to the high temperatures required, and to the formation of aluminum carbide and oxycarbide byproducts [7]."

Jan 1, 2013

By Qingchun Yu, Bin Yang, Yong Deng, Heng Xiong, Fei Wang, Minxiu Chen

"Metal aluminum produced by non-electrolysis process received much attention due to its lower energy consumption. In this paper, carbothermic reduction and carbothermic-chlorination of alumina in normal pressure and vacuum were studied. The products were examined by means of XRD, EDS and SEM. During the carbothermic reduction process using carbon reductant in normal pressure, no metal aluminum was found. However, when coal was used as reductant, a mixture containing metallic aluminum, A14C3, and silicon was obtained, but metallic aluminum couldn't be separated from the mixture. During the carbothermic-chlorination process in vacuum, Al404C and Al4C3 were produced by the reaction between alumina and carbon, and Al Ch gas reacted with Al404C and Al4C3 to produce Al Cl gas. Metallic aluminum was produced due to the disproportionation of A!Cl gas and condensed on the collecting plate. Meanwhile, the initial temperature of carbothermic reduction of alumina reduced in vacuum compared with that in normal pressure.IntroductionIndustrial production of primary aluminum is carried out in alumina cell by the so-called Hall- Heroult process, necessitating the use of very high currents of low voltage. The alumina from which metallic aluminum is gained must be chemically pure, otherwise impure metal results. The main drawbacks of the electrolytic production are its very high energy consumption, the release ofperfluorocarbons, and the high specific C02 emissions [1]. During the past years, there were a lot of attempts to produce metallic aluminum by carbothermic reduction of A1203 [2, 3]. Cox [4] determined the vapor pressure over the A1203-C system and performed X-ray diffraction analysis of condensed products. It was demonstrated that an increase in the carbon content in the system leaded to the sequence of transitions: A1203~Al404C~A1zoc~A14C3 ~AI [5]. In any carbothermic reduction process for aluminum, extremely high temperatures (2000 °C ) were required [6]. In spite of considerable effort, the carbothermic reduction of alumina to aluminum remains a formidable technical challenge, due to the high temperatures required, and to the formation of aluminum carbide and oxycarbide byproducts [7]."

Jan 1, 2013

By William J. Scott

In the last two years, C-CORE has developed a new seabed sampler directed specifically at obtaining samples from hard or compacted bottoms such as are typical of marine placer deposits. Samples are required for appraisal of concentrations of saleable commodities, and for determination of levels of biological indicators in the deposits. Recently C-CORE and the University of Victoria have been comparing the performance of the Scott/C-CORE sampler with that of the Van Veen sampler often used for biological sampling. Initial trials of the Scott/C-CORE sampler in 1992 at the WestGold mining site, Nome, Alaska, were described by Jewitt et al. at the 1993 UMI. Since that time the sampler has been modified to prevent overfilling, and to limit turbulent flow of water across the top of the sampler buckets when the sampler is recovered with partly-open buckets. The modifications included shoes to prevent sampler overfill, and flexible rubber shielding over top and sides of the sampler to prevent water circulation. Samples have been taken with both samplers in two field areas, one at Pine Cove, Baie Verte, Newfoundland, and the other near Long Pond in Conception Bay on the Avalon Peninsula, Newfoundland. In each area multiple samples were taken with both sampler types, and the samples processed immediately to establish the types and quantities of marine organisms that were present. Species identification is expected to be complete by late August.

Jan 1, 1994

By William J. Scott

In the last two years, C-CORE has developed a new seabed sampler directed specifically at obtaining samples from hard or compacted bottoms such as are typical of marine placer deposits. Samples are required for appraisal of concentrations of saleable commodities, and for determination of levels of biological indicators in the deposits. Recently C-CORE and the University of Victoria have been comparing the performance of the Scott/C-CORE sampler with that of the Van Veen sampler often used for biological sampling. Initial trials of the Scott/C-CORE sampler in 1992 at the WestGold mining site, Nome, Alaska, were described by Jewitt et al. at the 1993 UMI. Since that time the sampler has been modified to prevent overfilling, and to limit turbulent flow of water across the top of the sampler buckets when the sampler is recovered with partly-open buckets. The modifications included shoes to prevent sampler overfill, and flexible rubber shielding over top and sides of the sampler to prevent water circulation. Samples have been taken with both samplers in two field areas, one at Pine Cove, Baie Verte, Newfoundland, and the other near Long Pond in Conception Bay on the Avalon Peninsula, Newfoundland. In each area multiple samples were taken with both sampler types, and the samples processed immediately to establish the types and quantities of marine organisms that were present. Species identification is expected to be complete by late August.

Jan 1, 1994

By S. S. Clarke

ABOUT two years ago some of my friends were discussing the amount of drill-steel breakage that was permissible or not excessive, per month, per rock ton, per ton of steel or any unit of measure or output that would give a comparison between different kinds of drill steel. No one seemed to know what life to expect of steel, or what percentage of breakage might be termed excessive. In fact there were no operating data available to guide one in selecting the best steel for our mines, nor could any ideas or information be secured from the steel manufacturers. One was merely told that so and so used their steel and it was very satisfactory; or else one was given a highly technical lecture on their specific heat-treatment. Any estimates on expected breakage were just guesses, ranging from a fraction of a per cent to as high as ten per cent per month.

Jan 1, 1933

By K. B. Chaudhurl

The thermodynamics of the reactions taking place are examined with the aid of equilibrium diagrams for the Pb-O-S system. Based on investigations of chemical, mineralogical and differential-thermo analyses of intermediate products of different desulphuration degrees, an attempt is made to explain the mechanisms of the reactions in the smelting shaft of the KIVCET furnace. The differences between this and other direct lead smelting processes are demonstrated by these thermodynamic and kinetic considerations. Proceeding from these results, the practicability of direct lead smelting processes is discussed with reference to the composition of the primary feed materials to be processed. This comparison also considers the behaviour of minor metals, the products obtained and their characteristics in respect to further treatment. For assessing the operating costs, the over-all energy consumption is considered taking into account various price relations between electric energy and fuels/reductants. Based on the peculiarities of the various processes, an attempt is made to compare the necessary means of meeting the pollution control requirements. The paper concludes with reference to the criteria and problems involved in comparable evaluations.

Jan 1, 1978

By Thainá Silveira Garcia Mendes

A manutenção de monumentos e obras históricas deve ser executada com o uso de argamassa de cal, devido à sua maior permeabilidade e por preservar as características originais da obra. Entretanto, o uso de revestimento de tinta acrílica comercial sobre esta argamassa interfere na permeabilidade da construção como um todo, por vedar a superfície das paredes e tetos, internos e externos. Como uma alternativa que permite maior permeabilidade, tem-se a tinta à base de solo, constituída de água, cola branca e solo rico em silte e argila. O presente trabalho tem como objetivo quantificar e comparar as permeabilidades de amostras de argamassa de cal revestidas com tinta acrílica e com tinta de solo. Usou-se o método do tubo de Karsten para medir a permeabilidade dos dois revestimentos em comparação com a argamassa de cal sem revestimento. Os resultados dos ensaios indicaram que o revestimento de tinta à base de solo apresenta permeabilidade significativamente maior que a acrílica, sendo então mais indicada para o uso em restauro e manutenção de edificações históricas.

Oct 30, 2017

By Agnes Ágata Fróes Martins

O ensaio de impacto determina a resistência e sensibilidade dos materiais quando submetidos a uma certa carga de impacto, por isto, a importância deste ensaio. Através dele conhecemos as características que um material necessita ao ser projetado de tal maneira que possa suportar a uma força de impacto. Neste trabalho, o objetivo é comparar os resultados de energia absorvida no ensaio de Charpy analógico com o ensaio de Charpy instrumentado e verificar se há uma diferença significativa entre os resultados. Para isto, ensaios são realizados baseados em normas técnicas, neste caso a norma ASTM E23 [4]. Após os ensaios observou-se que os resultados do Charpy analógico e do Charpy instrumentado não obtiveram diferença significativa para todas as amostras ensaiadas. Em critério de avaliação dos resultados utilizamos a norma ASTM E2298 [8].

Aug 16, 2017

By Tiago Bristt Gonoring

Este trabalho estuda a redução de pós de hematita de alta pureza (com Fe2O3> 99,00% e tamanho de partículas

Aug 1, 2018

By Anthony Garotinho Barros Assed Matheus de Oliveirar, Wagner Anacleto Pinheiro, Andreza Menezes Lima

Óxido de grafeno foi sintetizado e posteriormente reduzido pelo uso de vitamina C. Para comparação entre o óxido de grafeno (GO) e o óxido de grafeno reduzido (rGO) foram utilizadas as técnicas de difração de raios X (DRX), microscopia eletrônica de varredura (MEV) e espetroscopia Raman (ER). Na etapa da síntese do óxido de grafeno por DRX confirmou-se a efetiva oxidação do grafite precursor, enquanto por MEV observou-se a esfoliação dos flocos de grafite em folhas de GO. Após a redução, por meio de DRX e ER analisou-se a remoção dos grupos funcionais, enquanto por MEV a morfologia das folhas do material.

Nov 16, 2019

By Marília Silva Cavalcante, Filipe Brito Marinho de Barros, Suelen Silva Rocha, Jorge Luiz Valença Mariz

A seleção adequada da taxa de produção de um empreendimento mineiro tem influência direta na possibilidade de sucesso do projeto, assim como a definição do porte e quantidade de equipamentos empregados em sua operação influenciam a maximização do Valor Presente Líquido (VPL). Nesse processo, a análise de risco na variável de saída aliada à análise de sensibilidade fornece resultados mais consistentes, visto que considera os riscos e incertezas de um projeto ao longo de sua vida útil. Este estudo teve como objetivo analisar a operação em uma mina de agregados a partir da consideração de quatro diferentes conjuntos escavadeira-caminhões através do método do Valor Anual Uniforme Equivalente (VAUE), comparando-o com o método do VPL. Foram revistas as avaliações econômicas efetuadas em estudo anterior, no qual foi obtido o VPL e efetuadas as Análises de Risco e Sensibilidade em cada um dos cenários, e foi acrescida à análise a metodologia do VAUE, sendo esta também submetida à análise probabilística. Foi verificado o desempenho de cada escavadeira e seus correspondentes caminhões para diferentes taxas de produção em ambas as metodologias, permitindo concluir que, para um mesmo número de unidades de transporte e contanto que a taxa de produção requerida seja possível, quanto menor o porte do equipamento, mais econômico é o cenário. Por outro lado, quanto maior a taxa de produção do empreendimento, mais rentável este será.

Oct 3, 2019

By Diego de Araujo Santana

O tamanho médio dos grãos é um parâmetro estrutural frequentemente estimado quando se está avaliando, principalmente, as propriedades mecânicas dos materiais metálicos. A American Society for Testing and Materials (ASTM) estabelece, nas normas ASTM E112 e ASTM E1382, metodologias para estimar o tamanho médio dos cristais de maneira manual e semiautomática/automática, respectivamente. O presente trabalho propõe, além de uma nova metodologia semiautomática, duas metodologias automáticas para estimar o tamanhão médio de grão em materiais metálicos policristalinos monofásicos, assim como um parâmetro para avaliar a morfologia dos grãos. O tamanho de grão G ASTM encontrado utilizando os novos procedimentos testados se apresentou muito próximo aos valores obtidos pelos métodos padronizados, que também foram aplicados e usados como referência para avaliação da representatividade das medidas. Desse modo, os métodos propostos se apresentam como uma alternativa viável para estimar o referido parâmetro estrutural dos materiais metálicos.

Aug 17, 2017

By P. Ramsaywok, G. Legodi

Spiral concentrators are widely used in the coal industry treating fine (-1mm) coal. Their application was a limitation to the product quality until the introduction of low-cut spirals which allow a lower quality ash product to be produced, thus expanding the market. The Exxaro Grootegeluk 1 (GG1) plant has a two-stage traditional rougher-cleaner spiral circuit using conventional SX4 spirals to produce semi-soft coking coal product at 12.5% ash by mass. The overall plant product is 10.3% ash meaning that the coarser sized coal dense medium separation circuits must compensate. A low density cut-point spiral targetting 10.3% ash would thus be beneficial to the overall complex. The spirals were tested in the two-stage plant environment and in a pilot plant. This paper discusses the findings and compares a two stage four-turn low density cut and conventional spiral. The two spiral technologies were unable to sustain a 10.3% ash product. Pilot test work was also conducted on GG1 coal, demonstrating that an eight-turn low density cut-point spiral achieves the targetted 10.3% ash under controlled conditions. Keywords: Spiral, low-cut, coal

Jan 1, 2020

By Kelvin Lo, Erwin Oh, Darren Newel

The use of interface elements is widespread in most numerical methods to separate the structural elements from soil elements. It allows slipping and gapping or overlapping between the two media in contact with highly distinct deformability characteristics, such as piles and retaining walls. However, many existing analytical methods still assume no pile-soil slipping before failure in axially loaded piles. This paper attempts to compare the slipping and non-slipping analytical models by introducing an interface with a virtual thickness. Results show that both have different load-displacement characteristics when comparing to the measured data. The non-slipping model would result in a stiffer load-displacement curve if the same input stiffness parameters applied to both models. Different procedures to calibration the input stiffness parameters in slipping and non-slipping models are recommended.

By Paulo Sérgio de Oliveira, Joaquim D. Donda, Andreia C. Rosa

"The search for energy efficient technologies for comminution processes is constant in mineral processing studies, since those processes represent a major percentage of operational costs. In this context the use of stirred mills is increasing, especially for ultrafine grinding. Although many authors claim that these new equipment are more efficient than the conventional ball mills, there were very little chances to prove that in a practical way, since there are few industrial circuits where those technologies perform the same duty. Therefore, the regrinding circuit of Germano second concentrator offers an interesting opportunity: a vertical mill operating in parallel with two ball mills. During almost two years of operation, several sampling campaigns were conducted to evaluate the vertical mill performance and to compare the operational data of the three mills. The industrial data was also compared to jar mill tests results, which are monthly conducted in Samarco labs in order to predict the specific energy consumption required by the ore fed to these circuits. The vertical mill demonstrated the same ability to achieve the product specifications of the ball mills while proved to be able to reduce the medium specific energy consumption in about 40%."

Jan 1, 2014

By Luís Marcelo Tavares, Juliana Segura

Comminution is one of the most energy consuming stages in a mineral processing plant. This consumption is not only related to the power supplied to equipment, but also to the indirect or embodied energy, mainly associated to materials that are worn during operation, including grinding media and liners. Until recently, preparation of iron ores in Brazil did not use comminution intensively, given that plants mainly produced sinter feed, natural pellet fines, besides lump ore. However, with decreasing ore grades, size reduction now occupies a centre stage in nearly all new plants. Technologies used up to date for processing low-grade iron ores in Brazil, in particular itabirites, have consisted of three or four stages of crushing followed by ball milling. A number of new plants are either being built or are currently being designed that will process the same type of ore, so that engineers are investigating alternative comminution routes. The paper analyses comparatively four comminution routes for processing a particular itabirite ore, many of which using technologies and layouts that have not yet been used in such application. Using data from bench scale and/or pilot-plant tests, the different routes are compared on the basis of sustainability principles in accordance to the Brazilian energy matrix, which is quite particular. It is concluded that if the sustainability criterion is used, then the optimal route would correspond to a circuit that uses HPGR technology with truncated feed followed by ball milling. Given the particular case of itabirite iron ores and specially to the one in the present work and the source of Brazilian energy, it is evident that indirect energy expenditure in comminution plays a significant role in greenhouse gas emissions when compared to direct energy, being the reason for the great attractiveness of HPGR technology. Evidently that these will have to be balanced against CAPEX, OPEX, NPV and other qualitative criteria, which can certainly lead to a different optimal circuit.

Jan 1, 2014

By Alex Ryberg, Matthew L. Becker

Several integrity testing methods exist which may be used to evaluate drilled shafts. Each test method has advantages and limitations. On occasion, the results from different test methods may lead to conflicting conclusions, making it difficult to conclusively know which results more accurately represent the quality and integrity of a drilled shaft. This case study focuses on the integrity testing evaluation for two drilled shafts which were constructed using permanent casings and installed through flowing river water. Integrity testing was performed using Thermal Integrity Profiling (TIP) and Crosshole Sonic Logging (CSL) on each shaft. During testing, the influence of flowing water and soil layering needed consideration in the collected TIP data. Similarly, concrete curing time influenced the CSL test results and required the CSL tests to be performed multiple times with additional wait times following concrete placement. To aid in the shaft integrity evaluations, Low Strain Integrity testing via the Pulse Echo Method (PEM) was performed on several shafts and concrete coring was also performed to help further assess the acceptance or rejection of the questionable shafts. This paper presents an overview of the testing methods that were applied, their basic methodology, as well as potential limitations that should be considered when evaluating their results.

Sep 8, 2021

By E de Necker, F D. I Hodg, L-M Cruywagen

The acid mine drainage (AMD) situation at three opencast collieries in the Witbank Coalfield, South Africa, was evaluated from different perspectives. Twenty-seven test pits were dug into the spoils of these collieries to characterise the in situ conditions of spoils of varying age. Detailed static testing was done on surrounding drill holes and additional samples were taken from the test pits. Selected samples were tested using different techniques, namely ABA, mineralogy and kinetic tests. Groundwater monitoring boreholes from the areas surrounding these spoils were also used for characterisation. The ABA results compared favourably with the in situ determinations; acidic test pits proved to be potentially acid-generating from ABA, even when the samples had neutral paste pH. Kinetic test results showed these samples to yield low pH leachate over the test period. In several of these results, the theoretical depletion of neutralising potential and the onset of acidity were well matched. NAG pH-values and final observed water chemistry corresponded for the cells predicted by ABA to acidify, but compared poorly in cells that did not acidify. Results from the non-acidic spoils were consistent with the in situ observations. Alternative kinetic test methodologies were also employed. Duplicate samples were tested in humidity cells and in aerated trays that were manually wetted on a regular basis. Results from these tests showed an excellent correlation. Detailed mineralogical determinations using XRD and XRF were used for comparison to the ABA and, in some cases, humidity cell results. These comparisons show that the ABA results are consistent with the results expected from the mineralogy. The conclusion from these assessments is that ABA, in most cases, provides information that can be correlated to the field, mineralogy and to humidity cells. The use of multiple techniques leads to a higher degree of confidence in the use of the data.

Jan 1, 2003

By R. E. Mitchell

The environmental impact assessment (EIA) is the accepted method for evaluating proposed mining and other industrial projects to obtain regulatory approval and to help companies plan for responsible development. Another increasingly common evaluation system for proposed projects is the environmental, social and health impact assessment (ESHIA). An ESHIA differs from an EIA for its generally more comprehensive and inclusive approach to evaluating potential impacts, such as on public health, and other features such as an ecosystem services approach to assessing biophysical and community impacts. An ESHIA may also be required by certain lenders for financing major projects. In this paper, EIA standards for the province of Alberta, Canada are discussed and compared to ESHIA. It concludes with several recommendations for consideration.

Jan 1, 2012

By E Niva

The IsaMillÖ is challenging the way that plants are designed and operated. This paper challenges existing designs of concentrator flow sheets, particularly focusing on magnetite circuits.   From what has started out as a small scale ultra fine grinding mill in the pharmaceutical and pigment industries, it has been redesigned and improved upon for mineral processing, and has been the mainstay of fine grinding applications for over ten years. These applications have required energy efficient grinding to succeed, and have been predominately in the base metals industry.   Further development of the IsaMillÖ has now resulted in the machines being able to treat larger tonnages, with higher capacity motors. This development, along with the introduction of purpose designed ceramic media, has allowed the mill to treat courser feed sizes. At the same time, the mill still offers highly efficient grinding, and has enabled it to be operated in coarser tertiary and secondary grinding applications.   The acceptance of the mill in coarser applications, predominately in base metals and PGM applications, has enabled the IsaMillÖ to be a serious contender for beneficiation in other minerals. One such application is the potential for IsaMillsÖ to be part of magnetite flow sheets, which are being considered in Australia to meet the growing iron demand of China. The high energy efficiency of the IsaMillÖ compared to conventional technologies, as well as the smaller infrastructure requirements, provides a great opportunity to reduce the power intensity of magnetite circuits.   This paper will examine the use of IsaMillÖ technology in conventional grinding applications, including recent testwork in a primary grinding base metal circuit, as well as testwork on magnetite ore comparing a lab scale IsaMillÖ with a lab scale Tower Mill.   The growing demand for minerals over the next decade, coupled with higher energy cost, will result in energy efficient technology, such as the IsaMillÖ, being included in standard circuit design.

Jan 1, 2008