Search Documents

By Y. Wang

In this study, homogeneous (unseeded) precipitation of nesquehonite (MgCO3.3H20) by the reaction of MgC12 with (NH4)2CO3 in supersaturated solutions at 30 °C was investigated. Factors which influence the precipitation of MgCO3.3H20, such as initial concentration, temperature, stirring speed, titration speed, equilibration time, have been studied. SEM images show that the initial concentration and titration speed have significant effect on nesquehonite's crystal morphology and particle size. In addition, stirring speed and equilibration time also have some influence on its properties. With the optimization of operating conditions, the crystals can grow up to a length of about 40µm and a width of 5µm, indicating good filtration properties. High purity nesquehonite obtained in this study was calcined to produce highly pure MgO at 800 °C as shown by XRD results. The novel process may be used to separate Mg and Li from high Mg/Li ratio brines in Qinghai, China.

Jan 1, 2007

By Afrodite Ntziouni, Vassilia Kasselouri – Rigopoulou, Athanasia Kyritsi, Konstantinos N. Pistiolas, Stamatia Gavela, Konstantinos Kordatos, Lazaros Iliadis

"The present study deals with the production and characterization of rice husk ash (RHA) and its use in the synthesis of zeolite of type ZSM-5. Rice husk was combusted in various temperatures with aim to find the suitable conditions for the production of amorphous silica. The resulted amorphous silica ash was then utilized as a starting material for the synthesis of ZSM-5 zeolite using the low temperature and atmospheric pressure process. The method led successfully to the synthesis of highly siliceous zeolite of type ZSM-5. The produced material was characterized using x-ray diffraction (XRD) and scanning electron microscopy (SEM).IntroductionRice husk is a major by-product of the rice-milling industries and it is usually used as a fuel for steam generation due to its high calorific power. During its combustion, rice husk ash (RHA) is produced. Knowing that the annual rice world production is over 615 million tons (2005), thus resulting in a potential production of more than 22 million tons of RHA [1], it can be understood that the RHA disposal is a crucial issue towards the environmental protection. However, due to the high silica content, RHA can be used as an alternative cheap source of silica for many uses, including as filler in polymers [2], concrete [3] and synthesis of zeolites [4-7].The burning of rice husk in air results in the formation of RHA with content in SiO2 that varies from 87 to 97% depending on the burning conditions, the rice variety, the climate and the geographic area [8]. Some small amounts of inorganic impurities are always present in the ash along with unburned carbon. The unburned carbon can be removed from the ash by further heating treatments in high temperatures, but this usually leads to the crystallization of the amorphous silica to cristobalite and/or tridymite [9]. The crystallization of the contained silica of the ash is also occurred when the burning conditions of husk are uncontrolled [10]. This crystallization is a disadvantage towards the preparation of silicon based materials, because the silica ash is rendered inactive in its crystalline form [11]."

Jan 1, 2008

By S Bluhm, LádeáOliveira, R Funnell

Taquari Vasouras potash mine (Vale Fertilizantes) has many interesting features including virgin rock temperatures of 50¦C at depths of 700 m. The mine has a relatively small shaft system with limited ventilation carrying capacity, which was not adequate to exploit the full extent of the deposit. This limitation was overcome by installing two large-scale recirculation systems with underground reconditioning centres. This paper describes this unique mine ventilation and cooling system and some of its history over the past two decades. The two controlled recirculation systems have been operating safely for some ten years and the use of large-scale recirculation has been a fundamental component in the increase of production and extending the mining further-and-further from the shaft centre. The recirculation systems have played a huge role in the mine profitability and comprehensively extending the mine life. The paper also discusses a number of novel design and operating features such as reverse running pumps for energy recovery. The underground chilled water system design required a number of special safety features in order to minimise the risk of water leakage since this could be catastrophic in a potash mine. This paper describes a good example of a mine in which the final ventilation and cooling system design ends up very different to what was envisaged at the greenfields stage.CITATION:Bluhm, S, Funnell, R and de Oliveira, L, 2013. Controlled recirculation and refrigeration at ValeÆs Taquari Potash Mine, in Proceedings The Australian Mine Ventilation Conference , pp 237-248 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

By Andrew B. Cecala, Robert J. Timko, Christopher J. Pritchard

As mine venti1ation systems become more complex, it is increasingly difficult to supply fresh air to the working face. A high percentage of the fresh air entering a mine never reaches the working face because it short circuits through stoppings and doors, exiting the mine without being utilized. When ventilation limits are reached, the only option presently available to most U.S. mines is to sink a new shaft - an extremely expensive undertaking that many companies cannot afford. Reusing or recirculating a percentage of ventilating airflow may make it possible for some mines to remain operational while maintaining a safe environment for workers. Such a study was performed at a trona mine in Granger. Wyoming. A vane axial fan was used to recirculate approximately 9.4 m /s (20,000 cfm), 25% of the total ventilating airflow, back to the working face area of a three-entry continuous miner section. This study involved two evaluations: the first when the face was 305m (1,000 ft) from the recirculation fan, the second when the face was 610m (2,000 ft) from the fan. The evaluation consisted of monitoring the mine atmosphere for respirable dust, methane (CH4). carbon monoxide (CO), and nitric oxide (NO), at various locations in the intake and return entries. Several shifts were monitored, with and without the recirculation system in operation. With the recirculation system in operation. there was an increase in measured respirable dust concentrations in the intake along with a slight increase in the mine temperature (1.67°C). There were also some minor changes in CO and NO levels in the intake entry, but this seemed to depend on the proximity of the instruments to the turn-around point for the diesel haulage vehicles, than to whether the recirculation system was or was not in use.

Jan 1, 1989

By A. A. Sobek

Controlled release systems delivering the required concentration of an effective bactericide over an extended time period have been developed by The BFGoodrich Company's ProMac® Systems group. The ProMac system is site-specific and includes a four-step approach to controlling acid mine drainage (AMD): (1) Diagnosing the problem, (2) Prescribing the treatment, (3) Supervising the application of controlled release bactericides, and (4) Honitoring the success of applied treatment. The success of the ProMac system is evidenced by improved water quality, healthy vegetation, a reduction in levels of acidophilic thiobacillus, and a corresponding increase in population of beneficial microorganisms.

Jan 1, 1986

By Greg Rappard, Francois Holowenczak, James Rickard

The King George V (KGV) Shaft forms part of MTR Corporation Limited (MTRCL) Works Contract 703 extension of the underground West Island Line on Hong Kong Island. The Shaft and the associated adit was the sole access to excavate the running tunnels. Originally during the Detailed Design stage, it was concluded that blasting was not feasible at the KGV Shaft due to the close proximity of sensitive receivers in the form of residential buildings, electrical cables and hospitals. As a result, the Contractor planned to excavate the Shaft using mechanical means with a programme time of seven months. The Contractor appointed a Sub-contractor to analyse the feasibility of excavating the Shaft by blasting. The Sub-contractor reviewed the proposal and recommended the use of an innovative blasting technique that had never been previously employed in Hong Kong. The Sub-contractor recommended the Shaft be blasted using DetNet electronic delay detonator technology, manufactured by AEL Mining Services in South Africa, with an initial 1.5m depth of water ballast covering the blast face. The electronic delay detonators provided initiation accuracy to ensure there would be no overlap between sequentially detonating blastholes. The water ballast makes use of the effect of energy lost through the shock front causing the water to break up into droplets creating a spray dome resulting in the attenuation of the energy imparted into the surrounding rock mass. Various tests have demonstrated that both the maximum overpressure and impulse density are significantly reduced when water of a minimum depth is in direct contact with detonating explosives. This innovative blasting technique reduced the excavation programme by three months, saved HK$5 million in direct costs and totally mitigated the impacts on the public and other stakeholders nearby the KGV Shaft. Peak Particle Velocities (vibrations) rarely exceeded 2-3mm/sec (0.08-0.12in/sec) at a distance of 30-40m (98-131ft) from the blast location and air overpressure levels were reduced below the Hong Kong target level of 120dBL. In total, 24 blasts were fired with an average advance of 1.6m (5.25ft) with an average powder factor of 2.03kg/m3 (0.127lb/ft3) to 1.84 kg/m3 (0.114lb/ft3). The initiation pattern had 5ms between sequentially detonating blastholes and 20ms between adjoining rings.

Jan 1, 2013

By Toshiaki Nakai, Kunihiko Takeda, Kimio Imaizumi, Hiroaki Shirasaka

"The new type of nano-porous silica particle was considered to be constructed by the spinodal decomposition-type process which was found to have narrower pores than those of conventional porous silica prepared from boron silicate or ""Shirasu"" balloon. Nano-porous silica particles were fabricated by the calcination of silica gel mixed with well-dispersed complex salts composed of phosphorous and molybdenum compounds. Both silica and inorganic salts were not perfectly dissolved in the suspension solution. After removing of the water, the silica-inorganic salts complex was volatized and successively calcinated at a temperature ranging from 650 °C to 800 °C. Then, the inorganic salts were removed by dissolving in hot water. Other inorganic salts such as potassium halides were also found to be effective as a pore-size controller.IntroductionControl of structure has an important role in the field of industry as well as in the separation and purification technology for metals and organic syntheses. Many studies on the control of material structures have been reported regarding porous materials with pores ranging from nanometer to micrometer scale. 1 ) One example is zeolite as a naturally yielded porous inorganic material. Various types of synthetic zeolites have been studied as ""molecular sieve"" materials with ordinary pore-size of less than one nanometer. In 1992, crystalline meso-porous material with a large surface area named MCM-41 was synthesized through the use of template synthesis. 2) In direct relation to our study, amorphous borate glass having 4 to 100 nm of fine pores known as Corning glass 3l or SiO2-Al2OrB2O 3-CaO porous glass having large pore dispersity ranging from 4 to 10,000 nm have been reported. 4 ) S) 6 ) Some examples of several reported studies are as follows: phase-separated porous glass consisting of B2OrAl2O3-ZrO2-RO-R2O complex oxide 7 ) glass with finer pore induced from hydrolysis of silane alkoxide, porous material attained by condensation polymerization through the use of sol-gel process 8), alumina meso-porous material 9 ) 10), silica-zirconia material 11), carbon porous material 12), etc.."

Jan 1, 2000

By Shangshu Li, Xionggang Lu, Xingli Zou, Zhongya Pang, Kai Zheng, Yinshuai Wang

Metal carbides (MCs), especially transition metal carbides have attracted a lot of attention due to their unique properties, such as high strength and hardness, good chemical and thermal stability. In this paper, a new route was proposed for preparing TiC nanoparticles directly from TiO 2/C precursor by using solid oxide membrane (SOM) technology in molten CaCl2. The TiO2/C pellet pressed under 8 MPa was used as the cathode, and a yttria-stabilized zirconia (YSZ) tube filled with carbon-saturated liquid tin was served as the anode. This process employs an inert SOM to separate the anodic reaction area from the molten electrolyte to control the electrolysis process. The electrochemical process was carried out in molten CaCl2 at 1000°C and 4.0 V from 0.5 to 4 h. The characteristics of the phase composition and morphology of the electrolysis products were investigated. The product electrolyzed was examined by X-ray diffraction (XRD) and scanning electron microscopy (SEM) with energy dispersive spectrometer (EDS). The results show that TiC nanoparticles can be obtained directly from TiO2/C mixture at 1000 °C, 4.0 V and for 4 h in molten CaCl 2 and the current efficiency is calculated to be 74.1%. In conclusion, we suggest that the SOM process is a promising environmentally friendly and low energy costs electrochemical method for the facile and controllable electrodeoxidation of MO x/C precursors to micro/ nanostructured MCs.

Mar 1, 2018

By Raden Haris Handayana, Jihan Farhan Lubis, Milia Putri, Tengku Deli Hamonangan Hasibuan, Sani Salahudin

An environmental issue that must be controlled from coal overburden blasting near the structure is ground vibration. Damaging ground vibration is the effect exerted from residual energy from blasting that does not work to fracture the rocks. Sebuku Tanjung Coal is a coal mining that operates T3 Pit adjacent to the High Voltage Tower. This structure is included in the Class 5 building with a maximum Peak Particle Velocity (PPV) of 40 mm/s. The shortest distance from the blasting location to the structure is 105 m. The initiation system used is electronic detonators combinate with emulsion as an explosives type. In Indonesia, the government regulated vibration limitation on SNI 7571:2010. The blast outcomes targeted are PPV below 40 mm/s, fragmentation size <80 cm for Excavator Komatsu PC-2000, and digging time <12 seconds. In this paper, the blast design was engineered by conducting Signature Hole Analysis for optimizing delay timing configuration and Scale Distance regression analysis to determine optimum charge weight per delay at the blast site. PPV results from 30 blastings achieved 100% below 40 mm/s with the range of about 1.773-30.250 mm/s. The deviation between PPV prediction to PPV actual is less than ±18% which provides the blasting with electronic detonator resulting in good PPV prediction for controlling vibration. The average fragmentation size (D80) is 55.81 cm in the 1st layer and 54.81 cm in the 2nd layer. The average digging time is 10.30 seconds in the 1st layer and 10.12 seconds in the 2nd layer.

Feb 6, 2023

By R. Bruce Sheibach

The Picher Mining District, located principally in north-eastern Oklahoma, was one of the world&apos;s largest lead-zinc mining areas during its 55 year life. The field covers an area of approximately 72 square miles (186 km.-); an estimated 1.6 x [103 yds3 of material (1.22 x 103m3)] worth in excess of one billion dollars, has been mined. Mining activities were typified by surface exploratory drilling identifying ore distribution and extension of underground workings to the lead and zinc deposits outlined. Exploration holes were either left unplugged or plugged at the surface with a section of a telephone pole. Low grade ore and waste rock were discarded in mined out portions of drifts. These waste piles containing pyrite and marquisette were left underground and oxidized during the many years of active mining. Upon cessation of mining activities in the mid-1960&apos;s, the drifts and shafts of the abandoned workings began to flood as the cone of depression filled in, leading to the dissolution of the oxidized sulfides and the formation of large volumes of acid mine water in the mined out openings. The resulting poor quality water, with high concentrations of cadmium, iron, lead and zinc, began discharging at the surface in 1979. Contamination of the underlying aquifer supplying local residents was first detected on a localized scale in 1980. The present surface water and ground water contamination have lead to the area being classified as one of the top ten hazardous waste sites in the U.S. by the EPA under the superfund program.

Jan 1, 1982

By Tyler Rockley, Cara Rosen

Blasting at a granite quarry in eastern Maryland produces elevated air blast readings that can fall into the cautionary zone for the state of Maryland environmental regulations on a semi-regular basis. When designing blast patterns in this quarry, challenging geology creates rough and uneven blast faces that can be difficult to capture with 2D laser profiling fully. Utilizing several methods known to manage high air blast results like pattern adjustments, decking, and timing changes have not achieved consistent outcomes. Accurately capturing and modeling this geology is the key to controlling high air blast. 3D modeling and profiling by drone is the solution to understanding accurate face profiles and real minimum burdens. Using 18 months of blasting data and air blast results to establish a baseline, the comparisons between blasts designed with 2D profiling and blasts designed with drone 3D profiling show improvement in air blast levels. Additionally, shots with completed drilling were drone profiled to understand precise amounts of burden for each borehole. This 'audit' of a blast allows for custom loading of explosives, accommodating the amount of burden present on the blast face. 3Dprofiling is not a new tool in the blasting industry, but a drone alleviates some of the restrictions ground systems face. Controlling and managing air blast, as it pertains to face burdens, requires an understanding of those burdens from all angles. A drone provides that distinct level of insight. The results of this study indicate that drone profiling is managing the customer's air blast readings, allowing the customer to maintain their license to operate within the community.

By Tyler Rockley, Cara Rosen

Blasting at a granite quarry in eastern Maryland produces elevated air blast readings that can fall into the cautionary zone for the state of Maryland environmental regulations on a semi-regular basis. When designing blast patterns in this quarry, challenging geology creates rough and uneven blast faces that can be difficult to capture with 2D laser profiling fully. Utilizing several methods known to manage high air blast results like pattern adjustments, decking, and timing changes have not achieved consistent outcomes.

Feb 1, 2020

By Steven E. Mischler

The exposure of mine workers to diesel particulate matter (DPM) and gases is an issue of great concern to the underground mining community in the United States. Approximately 30,000 underground miners are potentially exposed to high concentrations of DPM. In January of 2001, the U.S. Mine Safety and Health Administration (MSHA) promulgated rules setting compliance standards for both underground coal and metal / nonmetal mine workers. As industry works to achieve compliance with these standards, mine operators are looking for feasible methods for reducing DPM concentrations in their mines. In addition, the industry needs methods to accurately measure DPM to ensure that the control strategies they adopt are working successfully. The Pittsburgh Research Laboratory (PRL) of the National Institute for Occupational Safety and Health (NIOSH) conducts research to evaluate control technologies and monitoring instrumentation that can be used to reduce the diesel particulate matter (DPM) exposure of mine workers. An overview of the strategies being utilized in underground US mines to reduce DPM concentrations will be presented. Also, updates on the development of diesel monitoring instruments such as the continuous elemental carbon monitor or the Personal Dust Monitor for DPM measurement will be provided.

Jan 1, 2010

By D. R. Zuchelli

The purpose of wrapping ball mills with thermal/acoustic blankets is twofold: 1) to maintain the desired temperature inside the mill, and 2) to reduce the sound emanating from the mill. This field case study focuses solely on the latter, evaluating and documenting the sound level reduction attributed to the installation of the blankets on ball mills and its potential to reduce the noise dose experienced by the process attendant. One of the three ball mills had already been treated (baseline) before the evaluation started. However, treating the remaining two mills still proved to be very effective, further reducing ball mill noise in the near field by as much as 10.0 dBA and producing far field noise reductions of 3.0 dBA or greater, extending as far as 35 feet from the mills and to the floor above. The model developed from the survey data shows that a process attendant spending a substantial portion of a shift in the mill building will experience a significant reduction in overall noise dose.

Jan 1, 2010

By J Rock, K Bambrook

"Hanwha Mining Services was approached by Glencore Coal to provide a series of (trial) demonstration blasts at its Clermont coalmine. The intent of the project was to trial a bulk explosive product that would be able to provide sufficient energy for the ground type encountered without production of post-blast fume. Three blasts were loaded using the patented XLOAD bulk explosives with a density of 1.00 g/cc. XLOAD bulk products are water resistant explosives that can be loaded at densities much lower than traditional (generic) water resistant heavy ammonium nitrate – fuel oil (ANFO) or pumped blends with significantly reduced risk of fume. In addition, these products have detonation characteristics that generally deliver a higher heave partition than conventional bulk products and hence improve muck pile looseness and digability.The priority key performance measures included the absence of fume from blasting, being at least cost neutral and providing similar if not improved shovel dig rates. The design for the initial blast took a conservative approach to ensure the key blast outcomes of fume control and fragmentation were achieved.The second blast used the same pattern dimensions as the benchmark bulk product used in this area to provide a cost neutral comparison with the benchmark products that had been used over the prior six months. This resulted in a 20 per cent lower powder factor than would have otherwise been used. To test the suitability of XLOAD, this shot was slept for over two weeks between loading and firing in geology where the sleep time is typically kept to a few days to minimise the fume risk.The third blast utilised a slightly larger drill pattern to push the capabilities of XLOAD and provide a cost neutral comparison between the trial product and the traditional benchmark products. All three blasts were fired with no fume observed, no recordable incidents and good fragmentation. Shovel productivity from all three of the trial blasts was excellent with higher average instantaneous dig rates being recorded (average six per cent improvement against the instantaneous dig rates recorded for the benchmark blasts).Citation:Rock, J and Bambrook, K, 2016. Controlling Blast Related Fumes with Unconventional Explosives, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 39–49 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

By L. S. Harris

The application of briquetting in various chemical, mineral, mining and metallurgical processes has been rapidly increasing in the past two decades. This is, in part, due to the development of new, more economical and higher performance briquetting equipment. Some of these developments, which have reduced the operating and maintenance costs,, include anti-friction bearings, hydraulically applied pressure enclosed and sealed gearing and bearings, tapered predensification feed screws, water cooling and materials of construction capable of operating at temperatures up to 18000F, and control systems capable of maintaining optimum briquette quality control. The briquets can be formed into almost any desired size and shape, To date, with present rotary briquetting presses in the 25 to 500 ton force range, briquets from 1/4" to 6" length are presently being used, some of which are illustrated in Figure No. 1. In force fed rotary briquet machines, these shapes are produced by feeding the material in between a pair of counter rotating rolls, as illustrated in Figure No. 2. The rolls have forming dies indented into their circumferential surface, as illustrated in Figure No. 3.

Jan 1, 1973

By ZHONGLING ZHAO, WANTING SONG, GUOZHONG LIU, LEIXIN SHI, ZUI WANG, YUANYUAN LIU, KE GAO, DONGHONG JIANG, WANG LUO, PEICHAO LU, Jianwei Cheng, WANCHENG ZHENG, Gang Zhao, YUNGANG WANG, JIANBING ZHAO

Coal spontaneous combustion is one of the disasters occurring in underground coal mines. As a typical case, the spontaneous combustion of broken coal left in the longwall gobs often happen which could greatly interrupt the normal mining production. Such concealed thermal event is featured as rapid development and difficulty in locating “hot” spots. If such spontaneous combustion fails to be timely prevented and controlled, a large amount of toxic gases (mainly CO) and smoke could flow and diffuse in the underground working sections, which could present safety hazards for coal miners. In this paper, based on an coal spontaneous combustion event happened in a Chinese gassy mine, the fire ratios derived from the gas composition data obtained through the tube bundle mine atmospheric monitoring system are used in determining the fire status. A comprehensive and collaborative fire extinguishing effort including inert gas injection, underground pressure balance, and sealing enhancement are made to control the fire progress. Simultaneously, the effects of such works to control the spontaneous combustion event have also been quantified using the fire ratios to justify again. Finally, the danger of coal spontaneous combustion in gob is eliminated, and the longwall panel is successfully re-opened for normal production.

May 6, 2021

By ZHONGLING ZHAO, WANTING SONG, GUOZHONG LIU, LEIXIN SHI, ZUI WANG, YUANYUAN LIU, KE GAO, DONGHONG JIANG, WANG LUO, PEICHAO LU, Jianwei Cheng, WANCHENG ZHENG, Gang Zhao, YUNGANG WANG, JIANBING ZHAO

Coal spontaneous combustion is one of the major disasters in coal mines, and it can have devastating effects on the normal mining and production activities of mines. This paper presents the field investigation, field measurement, data analysis, and formulation of fire-extinguishing measures conducted to extinguish the fire from a coal spontaneous combustion incident that occurred in a high-gas coal mine in China.

By Anthony Iannacchione, Tim Miller, Nicole Evanek

The Subtropolis Mine is a room-and-pillar mine extracting the Vanport Limestone near Petersburg, OH. In February 2018, mine management began implementing a new mine layout to better control the negative effects of excessive levels of horizontal stress. Almost immediately, the conditions in the headings improved. Conversely, and as expected, stress-related damage was concentrated within crosscuts. Over the last 18 months, the mine operator has diligently experimented with different techniques/methods to lessen the impact of the instabilities in the outby crosscuts. The range of controls used by the mine operator include angled crosscuts, crosscut offsets, increased distance between crosscuts, arched crosscuts, cable-bolted crosscuts, altered blasting pattern, and windows. A window is used to resist roof deformation by leaving a strong brow of roof rock within the crosscuts.

By T. Bednarski, T. McCallum, L. Moya, L. Nsenga, B. Mbao

The accumulation of solids in solvent extraction (SX) circuits can cause problems with the physical and economic performance of the operation. These solids are responsible for the formation of crud, a solid stabilized emulsion containing organic, aqueous, air, and fine solid particles. The build-up of crud in SX settlers can limit SX operation throughput, require plant downtime, lead to higher organic losses, or result in higher aqueous in organic entrainment (all of which can have a significant, negative economic impact). Current practices for crud management are typically reactive. Crud is physically removed after it has been allowed to build to excessive levels in the circuit and processed mechanically using centrifuges or filtration. A new proactive solution has been developed to prevent crud formation and build-up. Low ppm dosage of an additive, ACORGA® CR60, into the pregnant leach solution (PLS) has resulted in reduced crud formation in pilot and commercial scale for a variety of PLS streams. This paper will review results from operations in North America and Africa, covering heap leach, concentrate leach, and agitated leach feeds. INTRODUCTION Crud formation and build-up in solvent extraction (SX) circuits has been a long time topic discussed and claimed to be crucial to the whole hydrometallurgical process (Liu, et al, 2006). Crud formation is present in all SX systems be it copper, uranium, zinc, etc., and Ritcey (1980) defined crud as a stabilized emulsion containing organic, aqueous, and fine solid particles. The ore type and feed composition is a major determining factor of crud formation and typically contains Si, Al, Fe, P, and sulfates (Ritcey, 1980). It typically builds at the interface between the organic and aqueous, but can also be observed as floating crud on the surface of the settler, or bottom crud, which is common to find in circuits treating agitated leach feeds such as in Africa. As crud formation has been unavoidable, many of the current crud management techniques are reactive, allowing crud to form and build in SX circuits. Once it does, it is removed and treated via different mechanical techniques, typically through some type of filtration or three-phase centrifuge, to remove the solids and recover the organic phase trapped within the emulsion (Ritcey, 1980). Automated pumping systems have also been designed and are frequently used in North American operations. The time and capital required to react to crud formation can be an overwhelming aspect to SX operation.

Jan 1, 2019