Search Documents

By Frank Firmstone

IN April, 1873, No. 2 furnace at the Glendon Iron Works being out of blast, it was decided to alter it from an open to a closed top. The three side flues, through which a part of the gas was formerly taken off, were 15 feet below the top, and as, for various reasons, it was not convenient to cut new flues through the brickwork at the top, as is commonly done with closed-top furnaces, a modification of Coingt's charger was employed. This apparatus, as figured by De Vathaire,* consists of a cup or hopper, like that used with the cup and cone, and a central pipe for taking off the gas, which descends some distance into the furnace, and has a projection around it forming a seat for a ring of a triangular cross-section, which closes the opening between the cup and the central gas-pipe. The charge is put into the cup, and by lowering the ring, is thrown into the furnace, a part going outside of the ring toward the walls, and a part through the inside toward the gas-pipe. In this form the apparatus was not applicable, for: 1st. With a gas-pipe three feet in diameter, in a top eight feet in diameter, the openings left by lowering the ring would not be large enough to let lump coal pass through. 2d. For the charger to shut tight, the ring must bear equally against the projection made for it on the gas-pipe, and against the edge of the cup. This would not be difficult to effect when the apparatus is first put up, but a comparatively small change in the relative position of the parts, such as is almost certain to occur from expansion, would cause the ring to touch the pipe or the cup, whichever happened to be the lower, first, and leave a leak between it (the ring) and the other. In the plan adopted (Fig's. 5 and 6, Plate I), the central opening in the ring is closed by the bottom of the gas-pipe, whereby more room is left for the passage of the stock when the charger is open, than if the pipe descended into the furnace; and the pipe, instead of being rigidly supported, rests on the ring, when the charger is closed, and follows it for two or three inches as it opens, until stopped by the counter-balance lever C. When the ring is raised to close the furnace top, it comes in contact first with the bottom edge of the gas-pipe, then both are raised to¬gether, until stopped by the ring touching the edge of the cup. In this way a good joint is made at both places. * Etudes our lea Haut Fourneaux, page 108.

Jan 1, 1874

By LUIS EAIYLNN SALAS

IF the ordinary wet method be attempted for silver-bullion containing tin, much trouble is experienced, varying with the amount of tin present. Even with a percentage as low as 0.05, the end-point is masked by a persistent turbidity, while with amounts ranging from 0.5 per cent. upward, the determination of the exact end-point is impossible, owing to the finely divided or colloidal metastannic acid resisting all efforts to cause it to settle, or to give a clear supernatant liquid. The object of the following experiments was to seek a remedy for these difficulties, and to find the conditions whereby the Gay Lussac method might be applied directly to these bullions. Material containing tin is met with frequently in bullion from Mexico or Bolivia; and tin is carried (sometimes in large quantities) in jewelers' sweeps. 1. A bullion was prepared containing Ag, 74; Cu, 25; and Sn, 1 per cent. A weighed amount was treated by the humid assay-method as if it were an ordinary bullion free from tin. Ten cc. of HNO3 (1.21) was added, and the bottle was heated until all traces of red fumes had been expelled. Before heating, the solutions were moderately turbid; and after heating, the turbidity greatly increased. One hundred cc. of normal NaCl solution was added and the bottle was shaken vigorously at intervals during 30 min. The turbidity persisted. The bottle was allowed to stand over

Mar 1, 1912

By S. Gqebe, A. Lewis, M. Rodriguez-Pascual

"Gravitational sedimentation of suspensions in various precipitation processes is hindered by colloidal stability. This is due to the high surface charge of the suspension and results in strong attraction/interaction between the ions on the particle surface and counter-ions in solution. Moreover, this strong interaction results in a charge build-up that renders the suspension stable. In order to induce gravitational sedimentation of these particles, a redistribution of ions close to the particle surface is required. We therefore sought to redistribute ions close to the particle surface by applying a magnetic field. This results in the reduction of interparticle electrostatic repulsive forces and a subsequent increase in the zeta potential of a suspension. For the purpose of this study, a copper sulphide suspension was used. Copper sulphide particles were exposed to a range of field strengths for set exposure times and their zeta potential was measured before and after exposure. All particles had an initial zeta potential value equal to or less than –40 mV prior to magnetic field exposure. A significant increase in zeta potential was observed, with values reaching a maximum of –16.5 mV when exposed to a 2 T field strength for 40 minutes. This is due to Lorentz ion shifts resulting from the Lorentz force exerted by the magnetic field on the particle surface. IntroductionMetal sulphide precipitation is a process for treating industrial waste streams with high residual concentration of mixed metal ions and acid mine drainage. This process has been reported to achieve higher metal removal compared with the industrially prevalent lime precipitation, due to the sparingly soluble nature of the metal sulphide precipitates formed. However, precipitation is governed by high levels of supersaturation which favour the formation of fine particles (Lewis, 2010). Consequently, some of the metal sulphide fines formed exhibit slow settling dynamics and thus tend to remain suspended in solution."

Jan 1, 2016

By Q. Han

A modified cast-on method has been developed to reinforce aluminum castings with steel insert. Defect-free bond between the steel insert and the aluminum casting has been consistently obtained. Data obtained from a push-out experiment indicated that the bond strength was much higher than that obtained using the Al-Fin approach. This paper introduces this modified method in four sections: the coating of the steel pins, the cast-in method, microstructure characterization, and the bond strength. The section on the coating of the steel pins contains coating material selection, electro-plating technique for plating Cu and Ni on steel, and diffusion bonding of the coatings to the steel. The section on cast-in method deals with factors that affecting the quality of the metallurgical bond between the coated steel and the aluminum castings. The results of microstructure characteristics of the bonding are presented in the microstructure characterization section. A push-out experiment and the results obtained using this method is described in the section of bond strength/mechanical property.

Jan 1, 2015

Small scale' table concentration tests have many critics. Many metallurgists consider that such tests are of problematical value because of the difficulties involved in conducting and interpreting them.Many kinds of small-scale ore dressing tests are difficult to conduct, and there is, perhaps, good reason for thinking that table concentration tests are amongst the most difficuIt.Interpretation of results from small-scale tests is the responsibility of the metallurgists and engineers in charge, and it is often held that small-scale table concentration tests are particularly difficmlt to interpret.TESTING FOR TABLE CONCENTRATIONOn analysis it appears that the difficulties encountered in conducting small-scale table concentration tests are of three fairly distinct kinds. Firstly, there are difficulties due inherently to the smallscale nature of the operations; for example the smaller width of all mineral bands on the table and the less complete separation due to the shorter length of travel between the feed and discharge points.Secondly, there are the effects of batch operation owing to the fact that the mineral particles behave differently during the initial period when the sample is just beginning to spread over the table, the middle period when feed and discharge are even and continuous, and the final stage, when the last of the sample has been added and the table is beginning to empty itself.

Jan 1, 1954

By Z. Leng

"After detonation of the explosive, the final blast-induced damage area around the blast-hole falls into three categories, namely crushed zone, fractured zone, and elastic deformation zone. This paper presents a modified model to calculate the size of crushed zone around a blast-hole in drill-and-blast, with the hoop compressive stress and cavity expansion effect taken into account. The material in the crushed zone was assumed to be a granular medium without cohesion, but with internal friction. On this basis, the formula for crushing zone radius was derived. The proposed approach was verified with tests reported in the literature and the simulated results from SPH-FEM coupled models. A full statistical analysis was also carried out, and the predicted values were found to be in better agreement with the test results compared with other models. A sensitivity analysis of the modified model showed that the size of the blast-induced damage area is mainly affected by the following factors: rock mass properties, in situ stress, and borehole pressure. In particular, the roles of borehole pressure and in situ stress are discussed. Finally, suggestions are made on how the size of the crushing zones can be decreased. IntroductionOver the past decades, drill-and-blast has become the most commonly used technology in rock excavation. It is well known that in rock mass fragmentation with explosives, the annular rocks around the blast-hole are converted into fines. The formation of these fines consumes a significant part of the energy of the detonation, which in general is ignored in the determination of the efficiency of detonation (Glatolenkov and Ivanov, 1992; Furtney et al., 2012). Many studies show that only 20–30% of the total explosive energy is effectively used in fragmenting the rock, and up to 50% of the energy generated by conventional charges is wasted in overcrushing of the crushed zone and the inner part of the fractured zone (Ouchterlony et al., 2004; Sanchidrian et al., 2007). How to control the crushed zone to enhance the effective utilization of explosive energy, reducing the unit explosive consumption and the engineering cost, is therefore of great significance."

Jan 1, 2016

By M. K. Mohanty

A modified coal flotation characterization procedure, referred to as the Advanced Flotation Washability (AFW) technique, has been developed which, compared to traditional procedures, provides a more accurate prediction of the optimum separation performance achievable by a froth flotation process. The AFW procedure uses a vertically-baffled flotation column which provides enhanced selectivity among particles of varying degrees of hydrophobicity due to a plug-flow environment and an improved carrying-capacity environment. In fact, the separation performance of the traditional procedures was enhanced by increasing the possibility of operating under improved selectivity conditions. The separation performance provided by the AFW procedure was superior to that obtained from multiple cleaning stages using commercially-available flotation columns under both kinetic and carrying-capacity limiting conditions.

Jan 1, 1997

By Z Fu, E Topal, O Erten

"Mine waste rock management involving waste rock movement and placement, is a critical aspect in the planning of open pit mining operations, as the waste rock haulage cost can be the largest portion of the mine operating cost. The concept of sustainable development in the mining industry also encourages environmentally friendly waste dumps that have zero hazards to people and the surrounding environment. Therefore, a detailed waste management schedule must satisfy economic and environmental considerations. However, the available tools in the market cannot provide optimal waste dumping schedules to meet all these constraints. This paper introduces a user-friendly and automatic tool to optimise the waste dumping schedule, which minimises the haulage cost, and covers the encapsulation of reactive materials to minimise acid mine drainage problems. This tool has been developed by using a new mixed integer programming (MIP) mathematical model that considers both single-lift and multilift dumping scenarios. The application of the proposed tool on a data set collected from a gold mine shows that the multilift dumping scenario has provided a more flexible and economical waste dumping schedule than the single-lift scenario, and both scenarios satisfy environmental requirements.Citation:Fu, Z, Topal, E and Erten, O, 2016. A Modified Software Tool for Mine Waste Rock Dump Planning, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 229–242 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

THE slide-rule, as a quick and convenient instrument for performing approximate calculations, is steadily growing more and more into favour with the engineer, and results obtained by it are considered close enough to enable him to satisfactorily dealwith a considerable portion of his work. To the surveyor, however, whose ordinary computations must be as precise as his measurements, the present makes of rule are insufficient, except for a very narrow margin of the scales and for rough work. Few will carry the rule when they can clearly see that it is unreliable for general routine, and the careful surveyor is inclined to look askance at those who do use it, recognizing the temptation there undtmbtedly must be to push it into work that the log book should be called upon to treat. From the fact that a surveyor's duties take him on the surface in all weathers, and underground in many wet and uncomfortable places, where the manipulation of a book of mathematical tables becomes both awkward and patience-trying, an efficient slide-rule must offer the mbst transparent advantages. Again, a surveyor being specially trained to read divided scales quickly and accurately, the slide-rule must commend itself as an apt addition to his outfit.

Jan 1, 1912

By David A. Newman

The Geomechanics Classification (Bieniawski, 1979) was modified for entry and roof support design in underground room-and-pillar coal mines. Adjustment multipliers were introduced to incorporate the influence of strata weatherability, high horizontal stresses, and the roof support reinforcement factor into the existing classification system. Sixty-two case histories of both standing and fallen mine roof were collected from two mines in the northern Appalachian coalfield. Twenty-seven engineering and geologic parameters were recorded for each case. A partial correlation analysis was carried out on the cases to establish which parameters have a significant impact upon the supported stand-up time of coal mine roof. Survival analysis, a statistical technique used in medical research to assess the effect of a drug or treatment on a patient's life expectancy, was conducted together with stepwise multiple regression to derive values for the adjustment multipliers. A practical example is included to illustrate the application of the modified Geomechanics Classification to underground coal mine design.

Jan 1, 1985

By N Weerasekara, M Bird, M Yahyaei, M M. Hilden, M S. Powell, J Franke, P Toor

The combination of new tools with a more rigorous approach to understanding the interaction of mill liners with overall mill performance and economics, forms the basis of an integrated approach to liner management. Based on accurate liner wear measurements, some (limited) physical mill inspections and surveys, accurate calibration of the mill load and analysis of process data, a whole new approach to liner selection, relining intervals and mill control is proposed. Collection and analysis of this information in operating mills illustrates the mill performance improvement which can be attained through this careful measurement and modelling approach.A more holistic approach to liner management is proposed, including a broadening of the current work to cover the potential benefits of improved relining technologies and predictive liner wear modelling. CITATION:Powell, M S, Hilden, M M, Weerasekara, N, Yahyaei, M, Toor, P, Franke, J and Bird, M, 2012. A more holistic view of mill liner management, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 95-104 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By Jinsuo Zhang

Investment in coal resource development is affected by a variety of uncertain factors. Investors can make a flexible, strategic decision to achieve the value of risk implicated in those uncertain factors. Therefore, based on real-option theory, we identified key uncertain factors that affect a coal resource investment project, and revealed the formation mechanism of option value in coal resource developing investment project. Then, a multi-factor decision making model was established for a coal resource development investment project with random changes of coal price, interest rate, convenience yield and production cost. Finally, we tested the model and analyzed relevant parameters by applying living data. Our results indicate this model reflects the value of risk implicated in uncertain factors for coal resource development investment, and is able to determine a critical point of decision making change when coal price and production cost varym respectively. By means of parameters analysis, the convenience yield has a positive effect on the project value. The interest rate has a negative effect.

Aug 1, 2013

By Bright Oppong Afum, Kojo Boakye, Kwaku Boakye

This research developed and simulated a novel multi-indicator Fatigue Detection and Alert System (FDAS) designed to enhance fatigue detection accuracy in mining environments. The system integrates a comprehensive set of inputs: eye blink rate, eye closure duration, yawning frequency, distraction levels, Pre-shift Check-in Scores (Self-report) and Electroencephalography (EEG) Levels. Using MATLAB’s Fuzzy Logic Rule Viewer (FLRV) and Simulink, simulations demonstrated the FDAS’s robust ability to process these diverse physiological and behavioural indicators accurately. It effectively classified operator fatigue into low, moderate, and high fatigue levels, consistently providing appropriate outputs and corresponding intervention recommendations across various mixed-signal scenarios. The system achieved a calculated accuracy of 85.19% across 27 test entries, with a standard deviation of approximately 1.8459, confirming its reliability for real-time fatigue monitoring. These findings highlight the significant potential of this fuzzy logicbased approach to proactively identify early signs of fatigue, substantially enhancing safety and operational efficiency in demanding mining operations.

Feb 22, 2026

By G Hancock, J Lowry, T Coulthard, W Erskine, M Saynor

An important part of planning for the rehabilitation of uranium mine sites is the ability to assess the geomorphic stability of the final landform, over time frames ranging from decades to millenia. Depending on the environmental conditions, erosion features such as gullies may incise into containment structures, potentially leading to the exposure and transport of encapsulated radioactive material. Further, erosion may lead to increased sediment loads and the transport of other mine-related contaminants off-site and into downstream waterways. While erosion may be monitored and assessed over the short term (years to decades), the longer-term behaviour (centuries to millennia) of such landscapes is not within any meaningful human management time frame. Landscape evolution models (LEMs) can provide information on soil erosion rates at decadal or centennial scales over large spatial scales, and evaluate the sensitivity of these processes to environmental changes. However, an important issue associated with the use of models is the ability to assess the reliability and accuracy of the model. In this paper, the CAESAR-Lisflood LEM is tested for its ability to predict soil erosion from a series of 30 m × 30 m experimental plots specifically constructed for this purpose on a trial rehabilitated landform at the Ranger Uranium Mine in the Northern Territory, Australia. Model predictions of bedload and suspended sediment loads from the erosion plots were compared with field measured observations collected over four wet seasons from the trial landform. Once calibrated for the specific site hydrological conditions, the predicted sediment yield – specifically, bedload – demonstrated an excellent correspondence with the field data. However, longer-term simulations of ten years identified an exhaustion effect in sediment yield from the landform. These latter results indicate that a weathering function needs to be incorporated into CAESAR-Lisflood to ensure confidence that the CAESAR-Lisflood LEM will be able to correctly predict the long-term evolution of a rehabilitated landform once it has been?constructed.CITATION:Lowry, J,?Saynor, M,?Erskine, W, Coulthard, T and Hancock, G, 2014. A multi-year assessment of landform evolution model predictions for a trial rehabilitated landform, in Proceedings Life-of-Mine 2014 , pp 67–80 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By D Hatton, S Wilson, F Orrante, M Taghimohammadi, F van der Walt, N Arslan, M Westcott

"Cayeli Bakir Isletmeleri is an underground copper-zinc mine in turkey. The ore is highly variable with feed grades ranging from 1–4 per cent copper and 1–10 per cent zinc. Due to this variability, ore characterisation and blending strategies are crucial for performance optimisation.This paper presents a case study for a multidisciplinary approach to process optimisation, integrating Geometallurgical and advanced control methods to achieve optimised plant performance. The results from comprehensive metallurgical tests and surveys were used to develop a mathematical model utilising SGS’s Integrated Geometallurgical Simulator® (version number 2.5.24.0). The model was employed to determine the most appropriate operational settings required to ensure that optimised grades and recoveries are achieved for each ore type.SGS’s Modular Expert Technology (MET) expert system was then implemented to target these optimum operational ranges utilising online grade and froth velocity measurements. The successful conversion and deployment of the modelled process parameters into an expert system has resulted in significant improvements in overall recovery and circuit stability.Citation:Arslan, N, Westcott, M, van der Walt, F, Hatton, D, Taghimohammadi, M, Orrante, F and Wilson, S, 2016. A Multidisciplinary Approach to the Optimisation and Control of a Copper-zinc Grinding and Flotation Circuit, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 115–122 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By Julián M. Ortiz

Uncertainty quantification of a spatially distributed variable at any scale can be handled through geostatistical simulation. Large computation time, storage, and post-processing of the realizations are required to obtain a final assessment of block uncertainty. Multi-Gaussian kriging is a flexible alternative to simulation. The idea is to compute the conditional distribution of uncertainty after normal score transformation of the original samples. Under the multi-Gaussian assumption, all marginal and conditional distributions are Gaussian, hence fully defined by their mean and variance. The parameters of the conditional distributions are obtained by simple kriging and can be back-transformed to the original units of the variable of interest. An estimate and any summary of uncertainty can be easily retrieved. The main disadvantage of performing multi-Gaussian kriging is that change of support is not straightforward, that is, calculating uncertainty of block grades. We propose a methodology to overcome this limitation by considering a matrix simulation to generate multiple probability fields. Each probability field is used to draw spatially correlated point values from the point-support conditional distributions, and multiple realizations of the average can be obtained. This permits the calculation of the average over the block and its uncertainty. These blocks may correspond to selective mining units or to volumes from longer production periods relevant for engineering decisions. They can even be disjoint blocks, such as when several faces are mined at the same time. POSTMG, a Fortran program to perform these calculations, is described and a case study is provided.

May 1, 2004

By A Grace, C Sennersten, A Davie, R Lyu, C A. Lindley, O Goldstein, T Thomas, L De Macedo Camargo

Block modelling is a well-established method for modelling ore reserves as a basis for strategic mine planning and mine development. Off-Earth mining, particularly of asteroids, can benefit from block models; however, the significantly different characteristics of asteroids and their methods of mining require reconsideration of the geometry and annotations of block models. Terrestrial block models consist of rectangular prisms within Euclidean coordinate systems. Their labels and parameters typically include location within a mine-specific coordinate system, x, y and z dimensions, specific gravity, hardness, grades of metals of interest and so on.These data provide an input to mine design and strategic mine planning. Mining asteroids may require different coordinate systems (eg spherical, elliptical or cylindrical, rather that Euclidean) and attributes that vary from Earth-based block models. These include: variable gravitational vectors throughout the block modelrotational moment or accelerationrotation rates. Materials within asteroids may show different isotopic compositions. Asteroid mining has the unique characteristic of a mine being identical with an asteroid. The position of the asteroid/mine in space and its full orbital elements provide critical inputs to mission design and costing. Hence, the block model concept needs to be extended with this metadata. The orbital position and behaviour of the Earth must be included for active mine planning, and increasing automation of mine planning and operations needs to consider terrestrial weather and telecommunications infrastructure. Financial planning requires analysis of the net present value of extraterrestrial mining compared with terrestrial alternatives, so a fully automated mining enterprise should integrate terrestrial and extraterrestrial block models at different scales and resolutions. Blocks can be indexed via octrees, allowing for hierarchical scales that support analytics for deriving new knowledge and correlating features across different scales.CITATION:Lindley, C A, Sennersten, C, Davie, A, Goldstein, O, Lyu, R, Grace, A, Evans, B, Pentecost, D, Thomas, T, De Macedo Camargo, L, Craig, J, Salomao, G N, Hellicar, A, Biggins, D, Timms, G, Coombe, M, Shahriar, M S, Smith, G and Rahman, A, 2015. A multilayer 3D index tool for recursive block models supporting terrestrial and extraterrestrial mine planning, in Proceedings Third International Future Mining Conference, pp 289–296 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015

By R Yang

This paper presents a fragmentation model for large production blasts in an open pit or underground environment. The paper shows that the particle velocity is directly related to pressure, strain, and strain rate and so it can be considered as driving force and mechanism of rock fragmentation. This is supported by the fact that a vibration with a larger peak particle velocity (PPV) generates larger disturbance in rock and so finer fragmentation or more blast damage than a low PPV. The crack distribution in rock from impact is based on findings from previous researchers (Seaman, Curran and Shockey, 1976; Liu and Xu, in press). The fragmentation size is calculated at three-dimensional grid points within a blast. The fines and oversized blocks are calculated explicitly – the fines generated close to blastholes and big blocks far from boreholes are modelled naturally. The multiple blasthole fragmentation (MBF) model takes surveyed irregular geometry of the free face of a blast as the calculation boundary. The MBF can model fragmentation with over one million grid points. Examples of the model’s field comparison are also included.The PPV at a calculation grid is estimated based on the same approach used for the near field non-linear vibration model (Yang and Scovira, 2007). The method is based on the dominant charge for a calculation grid point, non-linear charge weight superposition within a charge and from multiple charges, strain wave broadening, and amplitude attenuation with distance from a charge segment. The blasthole confinement affected by earlier firing charges is also taken into account.The MBF model inputs from blast design, such as: location and orientation of each blasthole, stemming length, blasthole diameter, multiple decking, bench height, initiation sequence, etc. It models the effect of the delay and its scatter in each blasthole on fragmentation and has a statistical modelling capability for geological random variation on attenuation of particle velocity wave. The wave reinforcement due to instantaneous waves arriving or diminishing cooperative contribution due to long delay intervals between charges is also simulated.The results are displayed in 3D volumetric plots, contour of fragmentation in cross-sections, and size passing curves for a whole blast or a region of the blast.CITATION:Yang, R, 2015. A multiple blasthole fragmentation model – its concept, formulation, capability and field comparison examples, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 177–186 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By P. S. Newall

As part of a much larger research project, factor analysis was employed to help interpret and compare the geochemical signatures produced by two different sample media; a traditional -80# soil fraction, and a coarse float. Both sample types were collected by hand auger from the extension zone of the Redmoor sheeted-vein complex and analyzed -for 19 major and trace elements. The rationale behind the study infers that the geochemical anomalies produced by wallrock alteration around such targets can be better detected in the lithogeochemical rather than the soil environment, sometimes at considerable distance from their source.

Jan 1, 1991

By Francis G. Stehli

Though sedimentary rocks comprise only about five percent of the volume of the continental crust, they cover about 80% of its surface, serve as important reservoirs for fluids, contain reserves of non-metallic minerals, and have in general been extensively drilled. However, most drilling has been shallow in comparison to the thickness of the crust and such deep drilling as has taken place is very strongly localized in sedimentary basins. This may be seen by reference to Figures 1 and 2 which show the location of wells that drilled deeper than 15,000' [=] 4.6 km. (Figure 1) and those that drilled below 20,000' [=] 6.15 km. (Figure 2). It is apparent that, even in regions of sedimentary cover, direct exploration below six kilometers has been very restricted. In the case of the metamorphic and igneous rocks which make up 95% of the volume of the crust, direct exploration has been much less extensive in terms of both area and depth. The present state of our knowledge of the crust below a' thin surface layer stands in marked contrast to our growing present need for raw materials and the needs of future generations. It also stands in contrast to our need for enhanced, scientific knowledge of the deeper crust, its configuration, its present state, its hydrothermal systems,-its evolution, and its materials. Lessons learned in exploring the third dimension of the sea floor, the vigorous prosecution of seismic profiling, the development of testable models for hydrothermal systems and mineral deposits, the need for better understanding of heat flow, state of stress, earthquake mechanisms, and a host of other phenomena all suggest that it is time to launch a national program for scientific exploration of the crust which uses drilling to test important hypotheses developed on the basis of indirect evidence.

Jan 1, 1985