Search Documents

By Harry R. Cedergren

Properly designed drainage systems can be of great benefit to many kinds of Civil Engineering works, including embankments, and often are the most economical way to protect such works from the damaging effects of water. To function properly, drains must be able to remove water without also removing soil or becoming clogged with soil or erodible rocks. The first criterion to be used in designing drainage systems, called the filter criterion, can prevent all such problems (erosion and clogging) when properly fulfilled in design and construction. The second requirement of drains is that they must be capable of removing all of the incoming water without the build-up of large amounts of head that can damage the protected works. To insure this kind of perfomance, the discharge capabilities of drains should always be verified by appropriate hydraulic and seepage calculations. This paper describes these two basic drain design criteria and also gives examples of application of seepage principles to the evaluation of the potential benefits of drains and to the design of drains for mine waste embankments.

Jan 1, 1985

By W. J. Karwoski

A ground-support system for grizzly and haulage drifts was tested in Magma Copper Co.'s San Manuel mine. Eight two-piece, wide- flange steel sets were erected in a ventilation drift on the 2315 grizzly level. The sets were lagged with three different materials and back- packed with pea gravel and sand. The pillar on either side of the drift support system was instrumented with stressmeters and rock-bolt load cells, the backfill with pressure cells, and the steel sets with load cells. Results indicate a better survival rate than with typical monolithic concrete.

Jan 1, 1979

By William E. Mead

Although this paper has been entitled "Design of Embankments for Tailings Ponds and Waste Dumps," a better title might have been "Site Selection and Design Planning for Tailings Ponds and Waste Dumps," The procedures normally followed in performing the engineering calculations based upon the measured soil properties will not be detailed. Instead, we shall look at the subject in broader perspective which considers the environmental factors and the fundamental design principles. Disposal of waste materials left from the extraction and processing of mineral deposits has become, in recent years, an important engineering consideration for mine and mill operators. Land occupancy and land values almost everywhere are increasing at a rapid rate. So is the size of mine and mill waste dumps, thanks to our advancing technology in mineral beneficiation. Mining companies are being pressured to "clean up" their operations, both literally and in a safety hazard sense. Once, long ago, the miner could use any convenient location to get rid of his mine waste and mill tailings without being concerned over possible infringement on the rights and well-being of the public. Today, however, he must pay close attention to these matters if he wishes to avoid liability suits and the unfavorable reaction of civic groups as well as local and regional government. Most operators keenly sense their increased responsibility, not only because they are legally vulnerable, but because they realize the necessity for sharing space harmoniously with the rest of society.

Jan 1, 1967

By W. J. Kempson

In recent years, substantial progress has been made with respect to the definition and control of the primary energy requirements in underground mines. Little has, however been done to develop a more detailed understanding of how to limit the various pressure losses which are intrinsic to shaft systems. This is in spite of the fact that more than half of the pressures generated by the ventilation fans in deep level mines are dissipated as pressure losses within the shaft system. This paper presents research which has been completed to optimise the pressure losses which occur in shaft systems as a result of the ventilation air flowing through them. In this regard, the response of various shafts to the ventilation air flowing through them was measured. These results were evaluated against the current theory for the calculation of shaft pressure losses. Finally the results of the measurements and calculations were used to calibrate a Computational Fluid Dynamics model of the shaft systems. This model was then iterated to allow meaningful conclusions as to the specific make up of the shaft equipment which contributes the most to pressure losses in shaft The results of the above analysis demonstrated that the current theory used for the evaluation of these pressure losses is deficient. The paper discusses these conclusions and the specific ramifications of the analysis. Finally, the understandings gained with regards to the above research are applied to the design and layout of equipment in mine shafts. In this regard, the shape and orientation of the shaft steelwork is evaluated and it specific interaction with the piping and conveyance is evaluated. Coming out of this evaluation are specific recommendations for the design of future shaft systems. These recommendations are based on the above models and offer specific savings on the lifetime operating costs of shaft systems.

Aug 1, 2013

By Eric J. Beckman

Recovery of metals from dilute solution, whether the matrix is solid, or liquid, remains a considerable technical and financial challenge. Methods currently exist whereby metals can be extracted from either type of matrix, yet these methods consume significant quantities of reagents and can also generate multiple waste ,streams in the process. Technology developed in our lab allows efficient application of environmentally-benign CO2 to a number of separation problems involving metals. For example, we have employed biphasic mixtures of C02 and water as a green acid leach medium. Metals have been extracted from a steelmaking process residue and then recovered as metal carbonates through depressurization. In this process, metals are extracted and recovered without the use of reagents other than CO2 and water, and CO2 is sequestered as a solid. In addition, through synthesis of Cal-miscible phase transfer agents, we have shown that CO2 can replace the organic solvent currently used in refining of precious metals, The sensitivity to pressure of phase behavior in a CO2-mixture may allow significant streamlining of the process as well. Finally, CO2 soluble chelating agents have been used to extract toxic metals from acidic effluent such as that found in plating facilities.

Jan 1, 1999

By D Johansson, A Nordqvist, D Mihaylov, N Petropoulos, M Wimmer

The flowability of the caved rock masses in the sublevel caving (SLC) mining method is of great importance. During the blasting process of a SLC-ring, the caved rock mass in front of the ring is compacted. As a result of this compaction, the mechanical properties of the fractured rock masses change, for example void ratio, angle of internal friction and structure of the compacted material. The changed mechanical properties of caved rock mass and recent blasted material can influence the mobility of the material, which could result in blockage of the flow path of the material. The identification of the involved mechanisms in this process can be done after a series of tests in different scales. However, there is no available equipment for dynamic measurements during blasting, ie velocity and displacement of the burden and in the caved masses. This study focuses on the development and laboratory evaluation of a measuring system that can be installed in a borehole. The first trial was carried out in a pillar, where two blastholes had been drilled (9.5 m) parallel with the drift and two measuring holes (16.5 m) were perpendicular to the drift. Two measuring systems were installed in the measuring holes. Some preliminary tests were carried out to find suitable initiation procedures for the emulsion explosive. Applicability and robustness of the developed measuring system were also evaluated. In addition to these tests, an expandable cement mixture was developed to firmly anchor the measuring systems in the boreholes. The measuring system consists of an anchor, armoured cable in a pulling tube and a protective case. The anchor is equipped with uniaxial and triaxial accelerometers. A potentiometric measuring system for displacement up to 2 m is installed at the end of the pulling tube and connected to an extendable spiral cable. All sensors are connected to a data acquisition system (DAS). Both measuring systems have their own DAS to acquire data in case of failure of one of the systems. The measuring system was tested in laboratory conditions with impact velocity up to 10 m/s. It was proven to be functional and gave reliable results.CITATION:Petropoulos, N, Mihaylov, D, Johansson, D, Wimmer, M and Nordqvist, A, 2015. Design of equipment for dynamic burden measurements, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 493–500 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By Nathaniel Arbiter

After almost 60 years of application in this country froth flotation is still by far the most important process for concentrating metallic ores as well as a number of nonmetallic ores including fluorspar, phosphate rock, and potash. Its use on iron ores and coal is increasing. In the metals groups the largest plants and the greatest progress are found in copper and molybdenum mills, and the section of this paper that deals with applications will be found most pertinent to that field. During its long reign the flotation process has passed through several phases of evolution and has achieved progress in economy, efficiency, and simplicity of operation. Much of today's success in the flotation of low-grade ores can be attributed to that progress. Even more important to us than our ability to cope with today's conditions are tomorrow's problems, which we can contemplate with some prescience and confidence. Our annual production of copper, lead, zinc, and molybdenum--to mention only the most important metals occurring in the U.S. as sulphides--must be held at a high level in the face of a declining grade of ore. It is probable that the tonnage of such ores mined and processed will double in this country before the turn of the century. Not only will many of the existing flotation mills be enlarged again and again, but larger mills will be built here and abroad to meet our needs. At this moment, in fact, there are at least three proposed new foreign mills or expansions that envision 100,000 tons daily milling rate on copper ores. Table I (1) shows the trend in copper ore grades in U.S. in recent years:

Jan 1, 1970

By S C. Dominy

Grade control programs aim to deliver economic tonnes to the mill via accurate definition of ore and waste. The foundation of a successful program is high quality sampling supported by geology and a suitable data management and modelling system. Underground sampling methods include chip, channel and panel samples; grab/muck pile samples; and drill-based samples. Grade control strategy is related to mining method and orebody type. Sampling protocols must be designed to suit the style of mineralisation in question. Holistic studies focussing on ore mineralogy and gold particle deportment, size and distribution are required for sample collection and preparation protocol optimisation through ‘Theory of Sampling’ application. Where possible, such programs should be undertaken early in the life of a project. Appropriate assaying procedures are also required. Program implementation will require suitably skilled individuals to train and mentor staff, with ongoing Quality Assurance/Quality Control (QA/QC) monitoring and review will allow protocols and staff to be updated as required.

Aug 22, 2011

By Benjamin Jennings, Jason Herron

In the summer of 2016 Xcel Energy experienced a storm event that resulted in the collapse of approximately 8.5 miles of a 345 KV transmission line near Rogers, Minnesota. In design of the new transmission line, Xcel Energy determined that ten tower locations would be replaced with steel H-frame structures supported by helical piles instead of wood H-frame structures supported by driven wooden piles. A steel foundation was proposed for the towers due to time constraints and site conditions unfavorable to large pile driving equipment. Xcel Energy contacted the helical pile manufacturer Hubbell Power Systems, Inc. (HPS) for aid in the design of a complete steel foundation for the structure legs. With the shear, moment, and axial loads provided, the manufacturer used pile group modeling and axial capacity software to design a four helical pile group; and used 3D modeling and finite element software to design a moment resistant grillage to connect to the tower base. The steel grillage utilizes a new moment resistant connection and clamp system to transfer loads from the piles to the grillage. This connection provides a true fixed head condition and reduces lateral deflection issues typical to smaller diameter piles in pinned head connections. The clamp is designed to deform the helical pipe pile shaft and transfer the full axial load of the structure through the mechanical and friction connection. The helical piles and the moment resistant grillage were manufactured with shorter than average lead times and a helical pile installation contractor performed the installation. An expedient plan of install was developed by the contractor that resulted in an average installation rate of one complete set of tower foundations per day. The design of the moment resistant grillage, clamping system, and excellent foundation construction by the contractor provided an expedient and efficient foundation system to be discussed in this paper.

Jan 1, 2017

By D. J. Dunn

Grinding balls, simple in shape, are actually sophisticated machine components, and essential elements of mineral grinding mills. Their physical properties and quality must be adequate to achieve design life and grinding mission with few failures. Consistant properties and freedom from breakage are essential. Size, mass, hardness profile, chemistry, and microstructure are important variables which should be designed, specified, controlled, and verified to achieve optimal mill performance. Failure to specify ball properties in detail or failure to obtain required ball properties and quality can cause milling productivity losses and excessive costs that could endanger a milling operations survival in the competive mineral industry.

Jan 1, 1989

By Emre Turk, Suat Gullu, Candan Gokceoglu, Ahmet Sirri, Asli Can

In this study, the ground improvement application applied under the live railway bridge's approach embankments in Sivas, Türkiye was investigated as a case study. The soil profile is mainly composed of orangish conglomerate, clay, silty sandy clay, and under claystone, and mudstone units in the study area. As a soil improvement method, the Deep Soil Mixing (DSM) technique based on the principle of simultaneous mixing the ground while injecting with the water-cement mix, was selected. The application of DSM columns is designed to be 45 degrees horizontal, in order to reach the deepest point of the soft clay units for better improvement against settlement. The core samples were taken from the DSM columns and the compressive strength tests were performed in the laboratory. The results were higher than the minimum designed values. It means that inclined DSM columns were applied successfully, and the excessive settlement problem was solved.

Oct 1, 2022

By A. S. Nortjé

At South Deep Gold Mine longhole stopes are backfilled using a cemented Cyclone Classified Tailings in its hydraulic state. The need to contain the hydraulic fill until cured requires a barricade. Due to the massive size of the stopes, the tailings can exert enormous forces on any such barricade. Barricades have long been in use, but recent failures in Australia and the large rate of filling required at South Deep solicited a robust design. A robust design must examine all foreseeable failures and the barricade must be able to resist all expected and, within limits, unexpected loads. The design should also be simple to construct and cost effective, limiting the impact of construction errors and unnecessary delays to production.

May 1, 2007

By George C. Toland

Most existing impoundment ponds and dams leak effluent into the soil or rock upon which they are constructed. However, proposed environmental legislation will require very stringent control on the release of toxic effluents such as cyanide. More exacting investigation, design, and construction techniques than have been used in the past will be required to satisfy these new regulations. This paper discusses the types of field and laboratory investigations required to develop the data for the design of an impoundment system containing toxic effluent, and discusses in detail technical considerations necessary to design this system. Design topics include reservoir sealing with natural and man-made materials; embankment sealing; embankment design considering stability, surface hydrology, capacity, and downstream catchment basins; and special implications of cyanide effluents.

Jan 1, 1975

By Yoichi Shimada, Katsuyuki Nishida, Shinichi Takahashi, Yasushi Okada, Yohei Nakamichi, Kazunori Oshiro, Taichi Terui, Sigehiko Sugie

"Temporary retaining walls are ordinarily used for tunnel construction work conducted using the opencut construction method. Retaining walls in such instances are typically installed vertically. However, shoring (such as struts and king posts) is required to ensure the stability of retaining walls in cases of excavation work to depths that exceed approximately 4 m. A new design and construction method that focuses on the effectiveness of retaining walls that are installed on an incline was studied with the aim of improving construction workability by omitting shoring. The inclined braceless excavation support (IBES) method, which was developed for use with the inclined buttress method, requires no shoring, even for deep-open-cut construction work and can be applied to deep excavation work on ground with a high groundwater level. This method has been applied at six work sites in Japan in recent years. This paper introduces the IBES design and construction method and presents verification results based on the design method, a model experiment, finite element analysis, and measurements obtained during construction work.INTRODUCTIONBackgroundIn the past, temporary retaining walls used in open-cut construction work have been installed vertically, and shoring (such as struts and king posts) has typically been used to ensure the stability of these retaining walls when the excavation depth reached 3–4 m. However, shoring interferes with structures built within excavations and requires box-outs and penetration sections in the structures, as well as concrete joints that raise concerns about their impact on the watertightness and long-term durability of structures (Figure 1).Shoring also narrows the space available for conducting construction work and reduces construction work efficiency, and the installation and removal of shoring increases the construction duration and cost. As a result, there has been a demand for ways to reduce or eliminate shoring to improve the quality of structures and construction work efficiency."

Jan 1, 2016

By P. T. Bissert, J. P. Ducarme, J. L. Carr, A. K. Smith

The continuous mining machine is a key piece of equipment used in underground coal mining operations. Over the past several decades these machines have been involved in a number of mine worker fatalities. Proximity detection systems have been developed to avert hazards associated with operating continuous mining machines. Incorporating intelligent design into proximity detection systems allows workers greater freedom to position themselves to see visual cues or avoid other hazards such as haulage equipment or unsupported roof or ribs. However, intelligent systems must be as safe as conventional proximity detection systems. An evaluation of the 39 fatal accidents for which the Mine Safety and Health Administration has published fatality investigation reports was conducted to determine whether the accident may have been prevented by conventional or intelligent proximity. Multiple zone configurations for the intelligent systems were studied to determine how system performance might be affected by the zone configuration. Researchers found that 32 of the 39 fatalities, or 82 percent, may have been prevented by both conventional and intelligent proximity systems. These results indicate that, by properly configuring the zones of an intelligent proximity detection system, equivalent protection to a conventional system is possible.

Jan 1, 2016

By D. L. Petersen, C. R. Nelson, P. M. Bergson, B. K. Nelson

Membrane waterproofing systems in large tunnels cause the partial decoupling of the concrete liner from the rockbolted and shotcreted reinforced rockmass. This decoupling leads to a loose fit of the liner in the excavation when shrinkage from cooling and moisture loss occurs. This increases tensile stresses which require either the addition of reinforcing steel in excess of common European practice or the potential for liner cracking. Hot weather concrete placement and cold weather service conditions increase the magnitude of the problem, while creep of the rockmass reduces it. Contact grouting also reduces, but does not eliminate, the problem.

Jan 1, 1991

By David Mast, Irwan Halim, Seung Han Kim

Fermilab is constructing a large underground cavern in Limestone to house scientific equipment. The cavern will have a complex L-shaped geometry and about 215-foot depth with relatively shallow rock cover, with service/egress shafts accesses into the cavern. Three-dimensional analytical models were developed to study the ground behavior and support performance. Multiple rock constitutive and failure models were evaluated. The models were significantly impacted by the high lateral in-situ earth pressure at the site. This paper will describe the design approaches that were taken to optimize the cavern arch geometry to allow safe construction in shallow rock, and permanent support requirements.

Jun 13, 2021

By D. S. Choi

Underground production of coal by longwall methods has increased significantly in the last few years and will very likely continue to: increase. There are several reasons for this. First, as mining moves into seams having greater overburden, roof exposure must be reduced since support will become' increasingly expensive. Secondly, the growing demand for coal has forced the coal industry to seek alternative, more productive, coal mining methods. In addition, the longwall method greatly simplifies the underground ventilation network. This paper addresses itself to the design of longwall development headings, particularly to those of the United States where multiple development headings are required by law. The most burdensome problem encountered in many longwall mining installations is deterioration of the tailgate due to the combined effect from, the active longwall gob and the old gob made by mining the previous panel.1 Portions of the tailgate entry are sometimes closed to such a degree that extensive repair work is necessary to keep the entry in usable condition. The purpose of this paper is to present the result of a study in progress which combines field measurements with numerical model analysis to reduce the cost of maintaining tailgate entries in longwall mining systems.

Jan 1, 1975

By Rollin A. Slater

The bulk materials handling industry has served silently for years as the skeleton structure and often the central system of nerves and nourishment for the body of basic production industries. During the past two decades, this body has undergone substantial growth and mutation to meet the surging demands of our national economy for more and better products. The steel industry has been prominent in this phenomena and plants of the sixties are as unlike the second war vintage as our current crop of basketball players differ from their fathers. Steel has kept pace with spiralling demand by innovation which has resulted in new processes and improved designs which generally yield greater production from fewer units. The supporting industry of materials handling has likewise improved its techniques and currently has a new stronger generation of equipment to perform its necessary supporting function. It has been my fortunate experience to have been instrumental in the creative stages of several new steel mills which are currently in conceptual design or actual construction. Drawing upon exerpts from this experience, this paper will describe a basic approach to the selection and application of modern bulk materials handling systems to an entirely new steel plant. Specific details of past work are not available for publication, therefore, the plant described herein is a composite of ideas and will be the new plant of the Hypothetical Steel Corporation which will be located on the lower shores of the Great Lakes.

Jan 1, 1967

The paper describes the design of the dilute medium and medium recovery circuits installed at the coal preparation plants at the Cornwall Coal Company's Fingal Mine, and the BP Coal Australia's Howick Mine. These circuits maximize the use of clarified water for rinsing to improve the mass transfer of adhering medium from the coal surface into the carrying liquid, and have been combined with the use of a two stage magnetic separator. The separator utilizes a conventional concurrent first stage and a counter-rotation second stage. This combination results in high medium recoveries during both normal operation, and start up and shut down phases when large quantities of medium can be lost from a conventional circuit. Overall losses using this circuit have been estimated to be, 200g/t, over a twelve month period. Further advantages in plant operation are also obtained, especially steady operating conditions in the centre-tube pump tank, lower slimes contamination of the product, and lower quantities of non magnetics trapped in the separator concentrates. The techniques are particularly suited to incorporation in circuits treating coals containing high percentages of sticky and difficult clays, as are found in the Walloon coal measures.

Jan 1, 1987