Search Documents

By Jun Lu

The Pittsburgh seam is the most extensively mined coal bed in the Appalachian Basin. Unlike most other prominent coal seams, the Pittsburgh seam typically includes a sequence of immediate roof coals and intervening rock binders (or ?draw slate?), most of which are within mineable horizons. Furthermore, unlike the main bench, the thickness of the overlying roof coals and their intervening rock binders can vary significantly. For instance, in southwestern Pennsylvania, the Pittsburgh seam main bench typically ranges from about 5.0 to 6.0 feet thick with minimal variation over short distances. On the other hand, the Pittsburgh seam roof coals and immediate roof binder typically range from a few inches to several feet, and in certain geologic settings can vary significantly over short distances. Additionally, in some locations, very thick draw slate can totally replace the roof coals. Since the draw slate, which typically consists of claystone or clayladen shale, is relatively weak, the presence of thick and variable draw slate in the roof and rib can significantly affect mine safety and productivity. This paper presents the adverse effect of thick draw slate on a 1500-foot-wide longwall face in a southwestern Pennsylvania coal mine. Mapping of the thick draw slate, numerical models which illustrate stress distribution and failure associated with thick draw slate, and operational adjustments instituted to mitigate the negative impact of thick draw slate will be discussed in detail.

Jan 1, 2013

Gangue-cemented paste backfill (GCPB), is a well-established green mining technology and significantly improves the recovery rate of mineral resources, prevents mine dynamic disasters, reduces surface subsidence, and consumes a considerable amount of solid waste. The addition of an early strength agent as an additive in cement-based materials provides several security, technical, and economic advantages. In this study, the early strength agent on the early age (3, 7 and 28 days) strength of GCPB is evaluated experimentally. The GCPB specimens have an initial sodium sulfate early strength agent concentration of 0%, 1%, 2%, 3%, and 4%, and the obtained samples were analyzed by testing for uniaxial compressive strength (UCS) and scanning electron microscopy (SEM). The test results show that the UCS of the GCPB specimens with sodium sulfate is much higher than that of the blank specimens. When cured for 3 days and 7 days, the strength of GCPB with 2% sodium sulfate increased the most, by 131% and 116% respectively. When cured for 28 days, the strength of GCPB with 1% sodium sulfate increased by 135%. Scanning electron microscopy (SEM) results showed that the GCPB with 1% and 2% sodium sulfate had better internal structure compactness, thicker acicular crystals, and more flocs. As a kind of early strength agent, sodium sulfate can react with calcium hydroxide to generate calcium dihydrate sulfate and then react with calcium aluminate; the hydration product (C3A) quickly generates calcium sulfoaluminate hydrate (AFt) needle-shaped crystals, forming an early skeleton and improving the early strength.

Jan 7, 2020

By George F. Comstock

IT has been reported recently1 that the hardenability and toughness of forging steels may be improved appreciably by the use of complex deoxidizers containing titanium, aluminum, and vanadium. In the light of these results, an investigation of similar deoxidizers containing various hardening and grain-refining elements was proposed. These deoxidizers included three manganese-silicon-aluminum-titanium al- [ ] loys with and without boron and calcium, three titanium-aluminum ferroalloys with vanadium, molybdenum and zirconium, respectively, an aluminum-zirconium ferro-alloy, and plain ferroboron. Their approximate compositions are given in Table I, and the results obtained so far in the investigation of their effects on steel are presented in the later parts of this paper. METHOD OF USING DEOXIDIZERS The deoxidizers listed in Table I were used in three series of 0.40 per cent carbon steels, which were melted in a small basic-lined induction furnace and cast in the form of I7-lb. ingots about 2.75 in. square. The basic charge for each heat was 10 lb. Armco iron and 6 lb. of clean low-carbon sheet-steel scrap. When melted, this charge was deoxidized with 15 grams of ferrosilicon, then about 500 grams of pig iron was added to give the desired carbon content. After the pig iron was dissolved, nickel [ ] shot and high-carbon ferrochromium were added if required, and additions of 80 per cent high-carbon ferromanganese and 50 per cent ferrosilicon were made to provide the proper amounts of those elements. Aluminum was added to every heat 2 min. after the silicon, for grain-size control and preliminary deoxidation. One minute later the special deoxidizer was added to the clean bare surface of the molten steel, and 2 min. afterward the steel was poured into the ingot mold, using a hot-top and pipe-preventing compound after pouring to decrease the depth of the shrinkage cavity. The special deoxidizers were used mostly in the form of about ½ to ¾ -in. lumps,

Jan 1, 1942

By Charles Zdazinsky

Over-break is undesirable in underground civil construction because it excessively damages rock along the perimeter of the tunnel, which directly influences the cycle times of advancement. A quicker cycle time for each process is required to optimize the operation and therefore minimizing over-break is essential for operational success.

Jan 1, 2015

By M. Nakai, G. Itoh, R. Yamada, A. Kurumada

In order elucidate the mechanism for poorer fatigue properties of 7000 series aluminum alloys than those of 2000 series alloys, the effect of the test environment on the fatigue crack growth of the two series alloys was investigated, considering the relationship to hydrogen embrittlement. Two 7075-type and four 2024-type alloys were T6-tempered and T4-tempered respectively, and subjected to fatigue crack growth tests in moist and dry environments. When tested in moist air, fraction of intergranular crack path was higher in the 7075-type alloy with coarse equi-axed grains than in the 2024-type alloy with similar microstructure. This was in accord with the larger crack growth rate in the 7075-type alloy. Both the intergranular crack path fraction and the crack growth rate were decreased by changing the environment to the flow of nitrogen gas. Thus, the large fatigue crack growth rate of the 7075-type alloy is attributable to hydrogen embrittlement.

Jan 1, 2015

By Henara Lillian Costa

This paper aims to investigate the effects of a possible incorporation of ethanol to the lubricant during engine use on friction and lubricant film thickness, by adding small amounts of ethanol to Group I base (with and without an organic friction modifier) and to formulated oils. Film thickness was measured using ultrathin film interferometry. Friction tests were carried out using a mini-traction machine to obtain Stribeck curves. The film thickness measurements showed that in the region of low speeds, where the elastohydrodynamic film is very thin and therefore boundary lubrication may prevail, the addition of ethanol produced some boundary film, which was not present for the base oils. For the base oil with an organic friction modifier, the presence of ethanol increased the thickness of the low friction boundary film. For the formulated oil, the addition of ethanol reduced film thickness in all lubrication regimes. The friction tests showed some friction reduction due to addition of ethanol to the base oil, in particular at low speeds. For the formulated oil, the addition of ethanol reduced friction at high speeds, which was associated to a reduction in the viscosity of the lubricant, but at low speeds, the presence of ethanol reduced the formation of a boundary layer, increasing friction. For the base oil containing an organic friction modifier, the presence of ethanol increased the range of speeds for which low boundary friction occurred.

Jul 31, 2018

By S. E. Vanderslice, J. A. Hummer

"The results of laboratory evaluations were used to compare the potential of two alternative, biomass-derived fuels as a control strategy to reduce the exposure of underground miners to aerosols and gases emitted by diesel-powered equipment. The effects of fatty acid methyl ester (FAME) biodiesel and hydrotreated vegetable oil renewable diesel (HVORD) on criteria aerosol and gaseous emissions from an older-technology, naturally aspirated, mechanically controlled engine equipped with a diesel oxidation catalytic converter were compared with those of widely used petroleum-derived, ultralow-sulfur diesels (ULSDs). The emissions were characterized for four selected steady-state conditions. When fueled with FAME biodiesel and HVORD, the engine emitted less aerosols by total particulate mass, total carbon mass, elemental carbon mass and total number than when it was fueled with ULSDs. Compared with ULSDs, FAME biodiesel and HVORD produced aerosols that were characterized by single modal distributions, smaller count median diameters, and lower total and peak concentrations. For the majority of test cases, FAME biodiesel and HVORD favorably affected nitric oxide (NO) and adversely affected nitrogen dioxide (NO2) generation. Therefore, the use of these alternative fuels appears to be a viable tool for the underground mining industry to address the issues related to emissions from diesel engines, and to transition toward more universal solutions provided by advanced engines with integrated exhaust aftertreatment technologies. IntroductionDiesel engines have been the workhorses of modern society for industrial and transportation enterprises. Diesel engines of all generations are extensively used in a variety of light-, medium- and heavy-duty applications in underground mining operations around the world. Fuels obtained from various sources and with wide-ranging chemistries have been combusted in diesel engines. However, the bulk of the currently used fuel can still be traced to nonrenewable petroleum sources. The petroleum-derived diesel fuels are primarily made up of saturated acyclic hydrocarbons (parafins or alkanes), aromatic hydrocarbons (arenes or aryl hydrocarbon), and unsaturated hydrocarbons with double bonds (olefins and alkenes). Improvements in the quality of petroleum-based diesel fuels was identified in federal regulations as an important piece in resolving the puzzle of diesel engine emissions (Environmental Protection Agency, 2001, 2004). The reduction of U.S. diesel fuel sulfur content below 15 ppm had the effect of lowering sulfate emissions and enabling the development and implementation of catalyzed emissions control technology across a wide spectrum of applications."

Jan 12, 2017

By C Samuelsson, Q Shu, A Lennartsson, F Gyakwaa, A Andersson, J Isaksson

The physico-chemical property, viscosity, is essential for pyrometallurgical processes and influences the settling rate of valuable metal droplets in slag, affecting the metal recovery. The copper slag from smelting furnaces typically contains between 1 and 2 wt per cent Cu, which equals to or is higher than in most sulfidic copper ores mined today, meaning the slag is a valuable resource for copper extraction. A low viscosity is desirable for slag-cleaning through a settling furnace where entrained droplets settle under gravity. One approach to control the viscosity is through the slag composition. The literature has limited data on the correlation between viscosity, slag structure, and optical basicity of iron silicate slag with FeO/SiO2, CaO, and Al2O3 as factors. Therefore, the present study evaluated the influence of these factors on viscosity and correlations with slag structure and optical basicity. The FeO/SiO2 ratio (at%/at%) and the CaO and Al2O3 content were altered in two levels, resulting in a two-level full factorial design with three factors. The study was done by synthesising FeO–SiO2–Al2O3–CaO–MgO–Cr2O3 melts, followed by water granulation. The melt structure of the samples was analysed with the help of Raman Spectroscopy. The viscosity was then estimated with a high-temperature rheometer using a Mo spindle and crucible. The results showed a correlation between the optical basicity, FeO/SiO2 ratio, and viscosity, where a high optical basicity and FeO/SiO2 ratio were beneficial for achieving a low melt viscosity.

Jun 19, 2024

By K. Gharibi, A. Dehghani, S. Farrokhpay, M. Aghajanloo, M. Ostadrahimi

The effect of flotation operational parameters on froth stability and froth recovery was studied. Froth stability was measured using a special column. To determine the froth recovery, the froth height change model and froth height exponential model were used. It was found that since the interactions between the pulp and froth zones affect the time of froth formation, the exponential model is more suitable than the froth height change method for determining the froth recovery. The results showed that superficial air velocity and collector dosage have, respectively, the highest and lowest effect on the froth recovery, while froth recovery decreases sharply with increasing froth height.

Jan 1, 2021

By T. Emery, D. Sweet, J. Bourgeois, M. Gomez, B. Seymour, J. Feiler

For traditional underhand cut-and-fill mining operations, it can be challenging to design a suitable cemented paste backfill (CPB) mix that can meet the necessary strength requirements and yet maintain its ductility. In deep underground metal mines, the CPB must achieve a high enough strength to be competent under high stress conditions while also remaining ductile enough to withstand high strain from squeezing ground as underhand mining continues under backfilled stopes. To eliminate ground falls that result in injuries and fatalities, researchers from the Spokane Mining Research Division (SMRD) of the National Institute for Occupational Safety and Health (NIOSH) have partnered with Aerix Industries, a producer of concrete additives, to study the effects of foaming agents on the strength and ductility of CPB. This laboratory study examines the impact of various amounts of foam additive on the strength and ductility of CPB mix designs, using binder and tailings provided by Hecla Limited from the Lucky Friday Mine

Mar 2, 2022

Small-scale flotation tests have been conducted to examine the effect of froth stability on the column flotation of finely pulverized coal. The results of this study demonstrate that the upgrading of coal in a column flotation cell can be significantly improved when froth stability is properly controlled through the manipulation of appropriate operating variables. Several important correlations have been established from the test data. These relationships should prove useful for the design and ore ration of column flotation cells for fine coal processing.

Jan 1, 1991

By Michael. H. Moys, Clayton Bhondayi

An electro-resistive measuring technique developed by the authors was used to study the effects of superficial gas velocity and froth height on froth phase bubble sizes as a function of height above the pulp-froth interface. Flotation tests and the bubble size measurement were carried out in a laboratory mechanical flotation cell that was operated in a pseudo-steady state mode using primary rougher tailings slurry from Lonmin Platinum as feed. The values of intra-bubble impact distances (IIDs) which are the estimates for froth phase bubble sizes obtained from the measurements indicated that as superficial gas velocity was increased, the values of IIDs decreased for the two froth depths tested. Increasing froth height at fixed gas rate resulted in an increase in IID values especially close to the froth surface. Changing froth height and gas rate alters froth residence times; longer froth residence times mean more time for bubbles to coalesce hence larger values of IIDs and vice-versa.

Jan 1, 2014

By Onuralp Yucel, Ahmet Turan, Murat Alkan, Hasan Ozer

SHS (Self-propagating High-temperature Synthesis) is one of the important methods to synthesize B4C powders. The process contains the reaction of boron oxide powders (B2O3) with magnesium reducing agent and carbon black carburizer. SHS products are leached in HCl media to purify synthesized B4C powders in the following step. In the present study, effects of various functional additives (KClO3, KHSO4, MgSO4.7H2O, NaCl, MgO and Na2SO4) in the SHS stage were carried out. Various proportions of the additives were mixed with the initial SHS charge mixtures. Two different molar ratios were employed in the initial SHS mixtures as 1:3:0.8 B2O3:Mg:C and 1:2.5:0.8 B2O3:Mg:C. After the SHS step, HCl leaching process was applied to the SHS products. Filter cakes were dried and characterized by using X-Ray Diffraction Spectroscopy, BET and chemical analysis techniques.

Jan 1, 2015

By Göksel Hızlı, Selim Ertürk, Ayşegül Bilen, Raşit Sezer, Cüneyt Arslan

The carbothermic reduction of celestite is the first step in producing many strontium products. The way materials move in the rotary kiln has an essential effect on the carbothermic reduction efficiency as well as the temperature. In this study, the reduction of celestite ore and excess carbon blend in a laboratory-scale rotary kiln was investigated. In the experiments carried out at three different temperatures, the rotational speed and slope of the furnace tube were altered, and their effects on the reaction efficiency were examined. The leachability of the reduced powders and the content of the unburned coke indicated the optimal parameters for the reaction.When the speed was increased to 10 rpm, the powders weremoremobile in the stack and could react more easily with the furnace atmosphere. According to the results, celestite can be reduced by carbon at temperatures of 1000–1200 °C, at rates of between 5% and 75%. The maximumreaction yield (75%) was obtained with a slope of 2° and a rotational speed of 6 rpm at 1100 °C.

May 7, 2020

By F. Dehghani, B. Rezaie, T. Ghosh, A. Sachan

Comminution is an integral part of the mineral extraction process. However, the influence of the comminution method (ball and rod mills) on silica and magnetite particle shapes has not been substantially investigated. Shape parameters for fractions of -250+212, -150+125, and -106+75 μm sizes were examined utilizing a scanning electron microscope and a Clemex vision PE image analysis system. The silica particles displayed higher elongation and flatness parameter values for rod mill products, but roundness and relative width parameter values of rod mill products are less than that of the ball mill products. Magnetite particle elongation and flatness parameter values of ball mill products in fraction sizes of -250+212 and -106+75 μm are larger than rod mill products, but roundness and relative width parameter values of ball mill products are smaller than rod-mill products, but for the -150+125 μm size range the result is converse. Furthermore, particle elongation and flatness increased with decreasing particle sizes of silica, whereas, roundness and relative width decreased for both Ball and Rod Mills. In case of magnetite, ball mill products displayed an increase of flatness and particle elongations with decreasing particle sizes but flatness increased and roundness and relative width decreased. Similarly for rod mills, magnetite fractions of -150+125 μm were found to have the largest values of elongation and flatness. INTRODUCTION Comminution alters the size and shape, causes lattice distortion, changes chemical composition, surface area, surface-free energy, and polymorphic transformation of all materials. The quantity and quality of such changes depend on specifications of the material feedstock, the type of mill being utilized, the specific energy input, ambient temperature, and environmental pressure [1]. The shape difference between the milled products depends on different grinding mechanisms and the respective breakage principles that these mechanisms depend on [2, 3]. With decreasing particle sizes, the nature of the particle surface become crucial [1]. The influence of the breakage technique has been found to be non-trivial and heavily dependent on the type of grinding mill used for particle size reduction [4]. Shape is an important industrial parameter for predicting particle behavior in downstream processes. The shape parameter affects the way particles burn, compact, are recovered, flow in fluids, sinter, float, agglomerate, fluidize, interact with pulmonary tissue, cut, abrade, react with chemicals, form structural materials, and retain and permit fluids to flow [5, 6]. The distribution of particle sizes and shapes are important for mining, civil and chemical, pharmaceutical, and various other industries with interest in the population modeling of atmospheric dusts, smoke, and grit [1, 3, 6]. The shape parameter not only affects the chemical, physical, surface properties of particles but is also important for downstream processes [5, 6]. Image analysis has been found to provide detailed information about size and shape of the particles and can be used for the control of product quality [4].

Jan 1, 2019

By H. Cho

There is an indication that high-pressure roller milling promotes selective liberation due to preferential breakage along the mineral boundaries. A study was undertaken to compare the degree of liberation obtained by high-pressure roller milling with that of conventional ball milling. Coals with different HGI's were ground in a high-pressure roller mill and a ball mill to produce products with similar size distributions. The products were then subjected to float-sink separations to determine the degree of liberation. Also, the relative cleanabilities were compared by separating the ground products by froth flotation. The results from this study are presented in the paper.

Jan 1, 1994

By R. Butar-Butar, J. Mosher, G. Banini, J. Hollow, A. Villanueva

The effect of High Pressure Grinding Rolls (HPGR), as a preceding stage to a conventional ball mill circuit at PT Freeport Indonesia’s C1/C2 concentrators, has been studied in terms of downstream grinding efficiency and circuit performance. When milling the product from the HPGR, mill capacity increased by 21% for the same product grind size, when compared to processing similar ore from a conventional crushing circuit. This achievement is a result of several reasons, among them: reduction in feed size (F80), fines generation beyond the proportional reduction in F80, reduction in ore hardness induced by HPGR comminution mechanism, optimization of the recycle system of the HPGR and ball string optimization in the ball mill circuit given the new feed to the mill.

Jan 1, 2012

By A. Villanueva

The effect of High Pressure Grinding Rolls (HPGR), as a preceding stage to a conventional ball mill circuit at PT Freeport Indonesia?s C1/C2 concentrators, has been studied in terms of downstream grinding efficiency and circuit performance. When milling the product from the HPGR, mill capacity increased by 21% for the same product grind size, when compared to processing similar ore from a conventional crushing circuit. This achievement is a result of several reasons, among them: reduction in feed size (F80), fines generation beyond the proportional reduction in F80, reduction in ore hardness induced by HPGR comminution mechanism, optimization of the recycle system of the HPGR and ball string optimization in the ball mill circuit given the new feed to the mill.

Jan 1, 2012

By B. Damjanac, S. Maxwell, D. Chorney, M. Grob, F. Zhang, J. Hazzard

"A hybrid discrete-continuum numerical scheme is developed to study the behavior of hydraulic fractures crossing natural fractures. The fully coupled hybrid scheme utilizes a discrete element model for a core domain, within which the hydraulic fracture propagates and interacts with natural fractures, and a surrounding continuum domain to better approximate boundary effects. The results show that the behavior of hydraulic fractures crossing natural fractures is affected by a combination of factors. Nevertheless, three fundamental crossing scenarios can be identified from all of the simulations: no crossing, partial crossing, and direct crossing. Each crossing scenario has a distinct injection pressure history which may suggest guidelines for interpreting field hydraulic fracture injection data. Additionally, the capability for these models to generate synthetic microseismicity makes them appealing for the integration of microseismic field data with the reservoir geomechanics for ultimately providing a practical engineering tool for improvement of well completion and stimulation. The model is capable of examining and verifying four different shear deformation mechanisms associated with a propagating hydraulic fracture. The natural fracture can fail solely due to the stress perturbation of the passing hydraulic fracture or it can fail due to a combination of stress and pore pressure changes across different types of interaction scenarios. The simulations also illustrate that the level of fracturing complexity increases as the number and extent of the natural fractures increase. INTRODUCTIONAlthough hydraulic fracturing technique has been applied extensively as a reservoir stimulation technique in the oil and gas industry for over 60 years (Economides & Nolte, 2000), it is one of the key factors promoting the shale gas boom in the past decade (King, 2010; International Energy Agency, 2014). The hydraulic fracturing of shales can be differentiated from hydraulic fracturing of conventional reservoirs by the fact that shale formations often have a pre-existing discrete fracture networks which greatly impact the hydraulic fracture propagation. Based upon field production data as well as microseismic observations, it is believed that so called “fracture complexity” may result from interactions between a created hydraulic fracture and pre-existing natural fractures and planes of weakness (Warpinski, 2009; Maxwell & Cipolla, 2011)."

Jan 1, 2015

By Q. Li

"The precursor of In2O3 was prepared by hydrolysis precipitation/hydrothermal method using In(NO3)3 solution as the feed material and ammonium hydroxide as the neutralizing agent. The crystallinity, morphology and particle size of the products were characterized by SEM, XRD, BET and LPSA. The results showed that the hydrolysis product consists of an aggregate of cubic In(OH)3 particles with a short rod morphology. In the hydrothermal process, the structure, morphology and size of the particles changes through the mechanisms of Ostwald ripening and phase transition, respectively. When the hydrothermal temperature was less than 280 ?, the Ostwald ripening process took place, which changed the morphology of the particles from short rods to cuboids through dissolution-recrystallization. When the hydrothermal temperature was higher than 280 ?, the processes of Ostwald ripening and phase transition took place successively. Firstly, the morphology of the particles changed from short rods to cuboids through Ostwald ripening, and then, the phase transition from cubic In(OH)3 to orthorhombic InOOH occurred and the morphology of the particles changed from cuboids to polyhedron. INTRODUCTIONDue to its excellent electrical conductivity and optical transparency, indium tin oxide (ITO) film has been wildly used in flat-panel display, solar cell, antistatic coating and EMI shielding (Medvedovski et al., 2008). Indium oxide powder is one of the fundamental materials for preparing ITO film. Along with the development of ITO targets of both high density and large size, high quality indium oxide powders, such as single phase, nano-size, spherical morphology and mono-disperse, have been in high demand (Nakashima and Kumahara, 2002; Betz et al., 2006; Kim et al., 2007). The main preparation methods for indium tin oxide or indium oxide powders include chemical precipitation (Nam et al., 2001; Xu and Yu, 2007), melt atomizing-combustion (Chen et al., 2000) and spray pyrolysis (Ogi et al., 2009). Among them, chemical precipitation has been preferred, since it is simple, easy to control and suitable for industrial scale-up. In chemical precipitation method, indium oxide powders were prepared through the following steps: firstly, indium hydrate precursor was precipitated from an indium salt solution by neutralization using an alkali, such as ammonia; and then, indium oxide (In2O3) powders can be obtained from the precursor through calcination (Li et al., 2006), or solvothermal method (Lee and Choi, 2005), or hydrothermal processing/roasting (Xu et al., 2005; Chen and Li, 2007), respectively. However, the indium oxide powders obtained by direct roasting are polycrystalline, dispersable with a wide size distribution (Liao, 2006). The disadvantages of the solvothermal method are high cost, complicated after-treatment processes, as well as bad performances of the powders (Udawatte and Yanagisawa, 2000). Therefore, among three methods of obtaining indium oxide from the hydrolysis precursor, the hydrothermal process/roasting method is the most feasible to synthesize high quality In2O3 powder with uniform crystallinity and size (Kim et al., 2002; Zhu et al., 2004; Xu et al., 2005; Xu et al., 2005; Chen and Li, 2007; Seetha et al., 2009). However, current research on hydrothermal process-roasting method has been limited to the synthesis of a certain ITO or In2O3 powders under specific conditions. A systematic study on the phase transition, as well as the change of the morphology and size of the particles in the hydrothermal process is still missing. In this paper, the effects of hydrothermal processing on the mineralogy, morphology and size of products were investigated. The results showed that the evolution of crystal structure, morphology and size in the hydrothermal process was affected through the mechanisms of Ostwald ripening and phase transition successively. These results are novel and have guidance for improving the hydrothermal process for In2O3"

Jan 1, 2012