Search Documents

By Staff

"The Weyburn Oil Field, located 80 miles southeast of Regina, Saskatchewan, was discovered by Central-Del Rio Oils Limited, in January, 1955. As of January 1st, 1959, the field had 357 wells capable of producing an estimated total of 45,100 barrels of oil per day.Highly portable, economical, drilling rigs are used to penetrate the pay at a depth of 4,400 to 5,100 feet. Presently, the complete drilling operation for an average field well, including drilling, coring, testing, and running casing, requires 12 days. Drilling procedures are conventional for a field of this depth and no serious problems exist. Central-Del Rio core the productive section of all their wells, which provides valuable information for well completions and reservoir studies. Production casing procedure is to set through the zone and perforate the productive inter-val. This was found advisable due to the lensing nature of the porosity and permeability throughout the reservoir, and to the high connate water saturation encountered in the tighter sections of the reservoir in the north and northeast areas of the field.Although a few wells in the field have produced naturally by flowing or pumping without acid treatment, it has generally been necessary to acidize the wells to make them commercial producers. To date, acid treatments appear to effect better stimulation of the limestone reservoir than fracturing treatments. Perforation sealing balls have been used as an aid in selectively treating all of the perforated interval.The majority of the field is on pump, producing at a low gas-oil ratio. The main part of the field has water-free production, with most of the water being produced in the north and northeastern area. Salt-water disposal is now available in the field through two disposal wells completed in the Basal Blairmore sand.The Midale Beds ""Marly"" and ""Vuggy"" zones form the principal reservoir, which is a stratigraphic trap, with the north and northeast edges terminated by a porosity and permeability pinch-out and the south-west and west edges bounded by water-laden porosity. There is no evidence to date of a gas cap. The reservoir apparently is producing on a fluid-expansion-type mechanism. The increasing water production in wells on the southwest and west edges of the field indicated water encroachment from these directions, and suggests some recovery energy may be available from this source.The total probable ultimate remaining recoverable reserves have been estimated at° 332,469,000 barrels of oil. Markets have not been able to keep up with the rate of development of the medium crude re-serves. However, it is felt strongly that substantial additional markets for Weyburn medium crude will be developed by the producers in the near future at realistic wellhead prices."

Jan 1, 1959

By John C. Loretta

INTRODUCTION Organizations that regularly use project management services will almost certainly have their own views on the preferred systems and procedures. This chapter, therefore, describes Project Management for the personnel of groups not familiar on a regular basis with project management and deals with the basic questions that these groups can be expected to ask, such as: - What is project management? - Why is it needed? Project Management is the planning, implementation and monitoring of the Engineering, Procurement and Construction activities that are necessary to complete the project in the most economic manner. In the case of a crushing and grinding plant, completing the project would mean bringing it into full operat ion. Engineering is the design work for the purpose of producing drawings and technical specifications for Construction together with technical specifications and quantities for Procurement. Procurement is the arranging of con- tracts so that equipment, material and labour are brought as required to the construction site. Construction covers the on-site activities that bring together the components of Engineering and Procurement so as to arrive at a finished plant. Need & Cost Benefits Project Management systems are needed to allow progress and expenditures to be monitored so that any significant deviations from the plan can be identified and the appropriate corrective action taken. In this way, Project Management is able to give continual updated answers to the Owners broad questions. - What am I getting? - What will it cost? - When will it be ready? The need for Project Management is not always immediately apparent, a common belief being that the existence of the three components -Mining Company - Equipment Supplier - Construction Company - is sufficient to get the job done without a formal project management group. This trio

Jan 1, 1982

By J Euston

In the 1990s round flotation tanks were introduced as a result of the lower fabrication costs for larger cells. It was soon observed that round tanks held a number of further advantages over the traditional rectangular cells, such as better hydrodynamics, lower costs and reduced footprint per unit volume.In the last twenty years flotation cell sizes have increased almost exponentially and designs of 250 to 300m3 are a well established standard with plans for full scale pilot installations of 500m3. The option to install these large cells gives flexibility in circuit arrangements and allows efficient and economic matching of flotation lines with modern mill designs. The benefits of scale up are well known with reduced numbers of cells required, lower power costs per unit volume, etc. These benefits will be briefly reviewed with specific reference to the installation of 300m3 to 350m3 flotation cells at the Copperton Concentrator of Kennecott Copper in Utah, USA.The sophisticated techniques required to model these ‘supercells’ have led to a critical review of the fundamentals of flotation science and engineering. In addition to outlining the advantages of large flotation cells, this paper will review the science which supports, and occasionally challenges, the ongoing trend to larger flotation cells.

Aug 8, 2011

By J. Kuti

In room and pillar mining a large number of working points are arranged to follow a mining pattern. Geological and roof control problems can be overcome or their effect minimized by varying this pattern. Longwall mining on the other hand, fixes the mining pattern for anyone panel. This aspect of longwall mining leads to constancy, so that a well-conceived organization, ventilation, dust and roof control systems lead to daily repetition and subsequent simplicity of control. All the same, a fixed mining pattern calls for a very careful consideration and selection of design parameters. (Ref. 1.)

Jan 1, 1971

By D. M. Rippley

THE St. Lawrence Seaway Project ranks with the greatest engineering undertakings of all time. A summary of major materials going into the construction of this project, shown in Table I, will assist in an appreciation -of this fact. These data relate to Seaway construction only, and it should be remembered that two large-scale power projects are in the construction stage on the St. Lawrence river concurrently with construction of the Seaway. A project of such magnitude as the Seaway would attract widespread interest even if it were being constructed in a remote area. The fact that it is located in a heavily populated and developed section of both Canada and the United States has done much to enhance this interest, and in many ways complicates the problems confronting the engineer in the design and construction phases. Many consider the St. Lawrence Seaway to be a new idea that has developed within the past decade - such is far from the fact, because the St. Lawrence River canal systems have existed for more than a century, and the Seaway Project is but a new, larger, and more efficient version of a continually expanding facility.

Jan 1, 1957

By R. G. Dalbke

An increasing number of water pollution control systems are certain to be installed by many industries in the future because of new federal, state, and local government regulations, and because of the rising general concern about the deterioration of our water resources. Extensive engineering, some of it based on methods not yet developed, will be required if these new systems are to provide optimum pollution control. Capital cost, operating cost, and present and future regulatory requirements will be primary factors to be considered by engineers. This paper outlines procedures and gives examples of advanced engineering practices that have achieved efficient pollution control systems in the steel and nonferrous industries.

Jan 1, 1968

By V. C. Rogers

ALTHOUGH surveying at mining properties is fundamentally the same regardless of the method of mining, at Climax, due to the nature of the ground, the policy of advance development work, and extremes in climatic conditions, surveying practice has had to be revised to meet the specialized conditions of this particular type of mining operation. The company's mine is one of the largest underground properties in the United States. It has proved ore reserves of 275,000,000 tons, 60,000,000 tons of which have been broken. To date, 109,000 ft. of development drifting have been driven, as well as 40,926 ft. of development raising, 10,000 ft. of ventilation drifting and raising, 16,000 ft. of exploration drifting, and 206,000 ft. of diamond drilling. Normal production varies between 1.2,000 and 15,000 tons daily. Development work proceeds at a rate of 11/2 tons developed for every ton milled and with a development of 18,000 to 20,000 tons per day, the following crew is required to take care of mine and surface engineering

Jan 1, 1946

By C. E. White

The depletion of higher grade mineral reserves will accelerate the trend toward production from progressively larger and lower grade deposits. The discovery of adequate reserves of leaner ores will require the development of improved exploration techniques with a greater depth range. The principal challenges to the Canadian mining industry are to find the mineral resources required to meet fast growing world demand and to develop mining methods and equipment to ensure production costs which will strengthen our position in export markets in the face of in-creasing world competition. The challenges cannot be met without intensive efforts to attract more technical men to the industry and to improve their training.

Jan 1, 1967

By Robert A. Siokler

Approximately 75 percentage of the earth's land surface is comprised of shale or shale-like materials. Shale itself is composed of the residue from an almost infinite variety of weathered parent materials which have undergone deformations ranging from intense to negligible. Under standard test procedures, shales exhibit a very wide range of physical properties particularly if the test specimen is subjected to a change in moisture content, when the original test values may vary from 0 to 100 percentage. It is this wide variation in physical property values compounded by its ubiquitous presence that makes shale such a problem material to engineers. In reviewing the literature relating to shale, it is evident that the "problem" has been approached from many directions. In order to understand why shales behave as they do, investigators have sought mineralogical, geological, chemical, electrical, and physical answers. Each study yields valuable academic information, but few contribute much of value to the engineer in the field. Many valid relationships between shale strength or competency and clay type, clay content, organic content, water content, grain size, cementation, density, porosity, etc, have been established. Yet it is very difficult to extend these understandings to the in situ condition with results that can be used by the field engineer. One major reason earlier work has not produced better information lies in the ambiguity of the definition of shale. It is apparent that no one laboratory parameter can be successfully used to provide sufficient engineering information to properly describe in situ conditions. For example; shale with swelling clays will produce low strength values provided: the swelling clay is in sufficient quantity, the clay is dispersed throughout the medium involved, and there is a low value of cementation. Shales with high unconfined compressive strengths have been found with very low shear strengths. Sandy shales often provide as many ground control problems as clay shales. Shales of similar nature may provide good roof conditions in one part of a mine yet in another part of the same mine the apparently identical shale may cause substantial problems. A clear need exists to classify shale in a manner which will enable the engineer to better predict the strength and durability of shale-like materials. Studies at the University of Missouri-Rolla (UMR) have focused on finding parameters which influence durability and competency, while being discretely discernible through uncomplicated testing. Initial research concentrated on distinguishing shale8 on the basis of standard physical tests such as: unconfirmed compression, triaxial shear, and slake durability. As results accumulated, however, it became evident that moisture content played a much greater role in determining competency than had been recognized previously. As a result the focus of the research turned to developing tests which would evaluate the influence of moisture on shale behavior. The above work then became a foundation for a second phase of investigation in which a suite of standardized tests were developed to provide a classification procedure. From this study five tests were identified as being critical: Moisture Activity, Atterberg Limits, Submersion, Unconfined Compression, and Shore Hardness.

Jan 1, 1986

By Yingda Zhai

The range of interburden thickness between coal seams in Datong Mining District of China is large. From mining operation point of view, the closer is between the two seams, the greater is the impact from the upper seam when the lower seam is mined. This impact is most notable when the two seams are ultra-close. In this paper the definition of ultra-close seams and its practical method of determination are presented. Based on the difference in strata thickness in the interburden and the concept of "yield depth ratio" which is defined as the yield zone depth in the interburden to the total thickness of interburden, the roofs of the ultra-close multiple seams in the Datong District of China were divided into 3 types: (1) false roof or rock partings in coal seam. This type of roof does not require special handling except mining them simultaneously as one single seam. The roof thickness is slightly less than 0.5 m; (2) completely broken roof. In this type of roof, the yield depth ratio is larger than (or equal to) 1. When the roof thickness is larger than 0.5 m but less than 2.0 m, the yield depth ratio must be smaller than 1; and (3) fractured roof. In this type of roof, the yield depth ratio is less than 1 while the roof thickness is larger than 2.0 m. In retreat longwall mining, if the gateroads of the lower seam are located under the gob of upper seam, roof bolting can be used in the 3rd type of roof. But if the 2nd type roof exists, powered supports must be used.

Jan 1, 2005

By AIME AIME

T HE appointment of Herbert Hoover to the portfolio of Commerce in the President's Cabinet is to engineers the fulfillment of a long deferred hope to have an engineer in high political office and is a matter of congratulation to us for three reasons; because he is a mining engineer who represents the highest type of idealistic engineering effort; because he is a past president of the Institute; and because he has probably a broader grasp of world problems than any other living engineer. Frank A. Vanderlip in the preface to his book "What Happened to Europe" tells of the many interviews he had with the most prominent men in Europe which were made possible for him by his eminence as a banker and by the courtesy of the American ambassadors. He cites by name such well known figures as Austin Chamberlain, Sir Auckland Geddes, Monsieur Delacroix, Monsieur Briand, Mr. Padkrewski, Mr. Venizelos, Colonel House, General Pershing, Mr. Baruch, and many others and says :

Jan 1, 1921

By Frank Sames, Brad Terhune

In many construction projects and in most quarrying operations drilling and blasting remains the only feasible method of loosening rock in the removal of rock or overburden, the development of the quarry and in the production process of crushed stone. Often, a blasting plan is required for the project or the quarry’s permit with primary concerns over safety and site security, and compliance with environmental regulations or standards. From this plan, a blasting program has to be developed considering the varying requirements of production, the advance of the mineral extraction and the environmental impact. The actual blast design requires a planning and optimization process. This optimization process is driven by the blasting technicians/engineers, project or mine management and often by community concerns. The blast design process comprises the selection of blast parameters, including the explosives, and the actual layout of the blast. Design tools and controls range from conventional methods based on established blasting practices to advanced design tools or computer models. Blast monitoring and evaluation can also range from empirical to advanced blast assessment. The data and information from each blast or a series of blasts can further be used in the optimization process. Its success depends upon recording the data, the timely transformation of the data to relevant information, and the development of process oriented knowledge. The elements of the blast design process are summarized and described with examples of state-of-the art engineering controls. The reporting and monitoring of individual blasts is discussed with respect to data management and information systems. A conceptual overview of the components and interfaces of a blasting program is given and discussed on the background of technical, management and community concerns.

Jan 1, 2004

By J. Parke Channing

IT, HAS been my privilege to be Chairman of Engineering Council for very nearly three years, during which time Mr. A. D. Flinn, the. Secretary, and myself, have seen the organization develop until it is functioning smoothly and accomplishing what it can with the money at its disposal. The earliest attempt at what may be called an Engi¬neering Council, of which. I have any knowledge, was made six or seven years ago when the four Founder Societies each appointed two men, who occasionally met to discuss matters submitted to them which were of importance to, the, profession as a whole. I was one of the representatives of the American Institute of Mining Engineers.

Jan 1, 1920

Engineering Council has been elected to membership in the Chamber of Commerce of the United States. Its representative will be Mr. Harold W. Buck, of Viele, Blackwell & Buck, Consulting Engineers, New York City, Past-president of the American Institute of Electrical Engineers, his alternate being Mr. Irving E. Moultrop, of the Edison Electric Illum-inating Co., Boston, member of American Society of Mechanical Engin-eers and American Institute of Electrical Engineers. The Chamber of Commerce of the United States was formed in 1912 and now consists of more than 1100 organizations in every state of the union, in the out-lying possessions, and of all the principal American chambers of commerce abroad. One of the chief aims is to obtain the best business thought on national questions that concern business. Members of the National Chamber have the privilege of using all the facilities of the Chamber's offices in Washington when information is desired.

Jan 12, 1919

By R. A. May, P. J. Brooks, W. M. Smith

"Neill and Gunter Limited (NGL) has prepared a preliminary design and a cost estimate for a ferric chloride leach plant to recover copper, lead, zinc, and silver from a typical complex sulphide ore. This plant design is specifically intended to treat unconcentrated ground ore (flotation feed), but can be readily adapted to treat bulk concentrates. Samples of ground ore and bulk concentrate were obtained from Heath Steele Mines, Miramichi, New Brunswick, laboratory testing, and preliminary process flow sheet preparation was carried out by the Research and Productivity Council in Fredericton, New Brunswick. Approximately thirty drawings have been produced, including process and equipment flowsheets, process piping and instrumentation drawings, and preliminary general arrangements. Preliminary capital and operating cost estimates were prepared for a plant that would treat 1000 t/d of crushed and ground ore to produce about 30 000 tpy of zinc. Capital and operating cost estimates were also projected for plants up to 4000 t/d of processed ore. Recoveries of 99% for zinc, 98% for lead, and 96% for copper were achieved in laboratory tests on unconcentrated ore. These recoveries were higher than the overall recoveries obtained from bulk concentrate, yielding approximately 10% more revenue.A 1000 tonne per day plant was determined to have a low return on investment, however, depending on the size and type of mining operations employed and the FCL plant throughput. DCF-ROI projections of 20% to over 30% were calculated for 100% equity financed “green field” mine, mill and FCL plant operations of 2000 t/d and higher"

Jan 1, 1997

By Thomas W. Turk

The water treatment industry has historically been involved with reducing or inhibiting the inherant scale forming or fouling tendencies of natural waters associated with large industrial cooling water systems. Fouling is an extremely complex phenomenon. From a fundamental point of view, it may be characterized as a combined momentum, heat, and mass transfer problem. Chemical reaction kinetics is involved, as well as the solubility characteristics of salts in water and corrosion technology. It is a routine practice to over size pumps, piping and heat exchangers to compensate for fouling.

Jan 1, 1983

By T. W. Turk, S. A. Sass

The engineering design features of the Mercur Gold Project crushing, grinding, carbon-in-leach, bullion, reagent, and tailings disposal areas will be discussed in this paper. It presents a project overview and flowsheet along with selected design alternatives. During the engineering phase, major equipment and other features were selected to optimize design within site location and environmental constraints. The project team organization and procedures were adopted to accommodate multiple optimization studies while maintaining a tight engineering schedule.

Jan 1, 1985

By T. W. Turk

In May 1984, Davy McKee Corporation was awarded a contract for engineering design, procurement assistance, project management and startup services for two gold recovery plants? in the People's, Republic of China (PRC). The basic design of these two projects was to be accomplished by a combined effort of the Chinese and Davy McKee Corporation (DMC). The, design goals were to provide a state-of-the art plant while maintaining Chinese standards and design practices whenever possible. Chinese-manufactured equipment was to be used as much as possible. This paper discusses the project organization and procedures developed to accomplish the design goals, the process selection and design, and the selection and procurement of equipment outside of the PRC. Design development for grinding, leaching and carbon adsorption, and gold recovery are discussed in detail. The major goal of process selection and design was to provide common criteria for both plants. Equipment .sizing and selection was identical for carbon-in-leach adsorption, gold recovery, acid washing, and carboo regeneration for both plants. Of special importance is the design of the wastewater treatment system. Due to the cl0se proximity of a major population area, slurry discharging from these mines must be treated to meet drinking water standards. The process development and design of this system is also discussed in detail.

Jan 1, 1989

By B. Y. Wong

In April 1989, Southern Company Services signed a 3.5 year contract with DOE-PETC for generic engineering development of an advanced physical fine coal cleaning technology known as selective agglomeration. This technology offers the potential for significantly higher pyritic sulfur removal (90% +) than conventional coal cleaning (30 to 50%) while maintaining high Btu recovery (90% +). Engineering development will include bench-scale process development; component development; adaption or modification of existing unit operations; proof-of-concept (POC) module design, fabrication, testing and evaluation; and small commercial facility conceptual design. The information obtained during POC operation will be sufficient to result in a technical and economic design base that can support construction and operation of a small commercial plant. The major goal of the research is to develop selective agglomeration technology to achieve 90% pyritic sulfur removal while operating at Btu recoveries above 90% based on run-of-mine quality coal. This objective will be accomplished in two phases: Phase 1 -bench-scale and component development, and Phase 2 -POC module operation and conceptual design of a small commercial plant. Currently, work is proceeding under Phase 1 (Tasks 1-7) of the project. A review of the status of Tasks 1-7 is presented in this paper.

Jan 1, 1991

By N. Duda, W. Koperska, S. Anufriiev, P. Stefaniak

In mineral processing plants ore extracted from mines is processed to obtain a concentrate with the highest possible concentration of this valuable product. It is a complicated multi-stage process. Usually, the first step is sieving the ore, which is typically done using vibrating mining screens. There is often only a limited number of these machines in the technological chain, which is why their continuous operation, and proper maintenance is crucial for the whole process. Predictive maintenance is the best strategy in this case because it allows for minimising the number and duration of unexpected stoppages. It consists of the prediction of future failures based on available real-time data, and predictive models built upon this data using, for example, machine learning techniques. In this paper we concentrate on feature generation for future predictive maintenance model development for a vibrating screen, based on an example of a KGHM ore processing facility in Polkowice-Sieroszowice. We focus on two types of measurements: bearings temperature and vibrational data. Based on the raw data, the process of more advanced feature engineering is described. By transforming the temperature data we calculate characteristics of bearing cooling and heating dynamics, while based on vibrational data, the aggregated characteristics of the vibrations are derived. Such features are calculated on a long-term basis, and then they are compared to the data related to vibrating screen maintenance to estimate their significance for the prediction of particular failures of the machine.

Sep 1, 2021