Search Documents

The strength of anchorage of various types of roof bolts in permafrost depends on the types of rock in which they are installed. Variation in the mine thermal regime results in weakening of the roof and walls, and at times total loss of ice cement bonds takes place in the surrounding rockmass. In mines with positive ventilation air temperature, the wedge or expansion types of bolts may become weakened due to the transfer of heat into the anchorage through the metal rod and subsequent thawing of rocks. Effective operation and evaluation of roof bolt systems for mine workings in permafrost require predictions of the dynamics of wall thawing by warm ventilation air. This paper presents an analysis of the temperature distribution in the frozen host ground surrounding roof bolts, the area of interest being the vicinity of the anchors for point anchored bolt and the entire length for split set bolt

Jan 1, 1994

By Richard J. Mainiero

The Bureau of Mines has developed a prototype nonincendive explosive rock-breaker charge that can be fired unconfined in underground bituminous coal mines without the danger of igniting a flammable atmosphere that might be present. At present, unconfined shooting in underground coal mines is prohibited, but there are situations where the use of such shots would yield an overall improvement in safety. The charge consists of 1-1/2 lb of permissible water gel explosive in the form of a short cylinder 7 inches in diameter and 7/8 inches high, surrounded by a 1 1/2-inch-thick layer of damp salt, and encased in latex rubber reinforced with cheese cloth. The latex rubber housing provides a charge package that is strong enough to resist rough handling yet is pliable enough to conform to an irregular stone surface. A charge of this shape was found to be more effective at breaking rock than charges with lined or unlined cavities. Incendivity tests in a gallery have shown that the prototype charge will not ignite a flammable methane-air atmosphere when fired. Rock- breaking tests made with limestone boulders indicate that the charge will satisfactorily break stone slabs weighing 1 to 2 tons, and that two or more charges might be effective for slabs weighing up to 10 tons. In cooperation with the Mine Safety and Health Administration (MSHA), a test protocol for the certification of these charges as "permissible" for use in flammable atmospheres is being developed.

Jan 1, 1982

By G W. Wilson, M Aubertin

A desulfurised tailings cover was installed at the Detour Lake Mine in Ontario, Canada, to reduce oxygen penetration into the underlying sulfidic tailings. The cover ranges from one to 1.5 m in thickness and was intended to maintain high water saturation to reduce oxygen diffusion and consume oxygen by oxidation of the residual sulfide minerals. The tailings impoundment was instrumented to measure climatic parameters, water levels and water content profiles within the tailings and single-layer cover. One year of monitoring data was collected. Additional tailings samples were obtained for geotechnical and geochemical characterisation. The average grain size of the cover material was found to be coarser than the underlying tailings. Monitoring also indicated that air entry values of the cover material were lower than the tailings. Numerical modelling was conducted on the cover to predict water content profiles under varying climate conditions together with the depth of oxygen penetration and diffusive oxygen fluxes. Estimates of the diffusion coefficient and kinetic oxidation rates from field data compared well with values obtained by laboratory measurements. Numerical simulations indicate water saturations of less than 85 per cent can be expected under varying climate conditions. Predicted oxygen flux rates through the desulfurised cover over tailings with high acid potential indicate low flux rates reaching these tailings due to either consumption of oxygen by residual sulfur within the cover or saturation of the underlying tailings.

Jan 1, 2003

By M. S. Klima, A. P. Pinkerton

Solid-bowl (decanter) centrifuges are used extensively to dewater slurries in a wide range of industries. However, the application of decanters as classification devices is not as common. In this study, the performance of a continuous, pilot-scale, solid-bowl centrifuge was evaluated when classifying an ultrafine coal slurry containing nearly 60% material less than 10 µm. The test conditions included centrifuge howl and scroll speeds, volumetric feed rate, solids concentration and pond depth. Centrifuge performance was evaluated using size selectivity curves and the corresponding performance parameters, along with product yields and solids concentrations.

Jan 1, 2002

By M. S. Klima, A. P. Pinkerton

Solid-bowl (decanter) centrifuges are used extensively to dewater slurries in a wide range of industries. However, the application of decanters as classification devices is not as common. In this study, the performance of a continuous, pilot-scale, solid-bowl centrifuge was evaluated when classifying an ultrafine coal slurry containing nearly 60% material less than 10µm. The current study examined the effects of operating conditions on centrifuge performance. The test conditions included centrifuge bowl and scroll speeds, volumetric feed rates, solids concentration, and pond depth. Centrifuge performance was evaluated using partition curves, along with product yields and solids concentrations.

Jan 1, 2000

By Jr. Watts, B. K. Cantrell, K. L. Bickel, J. F. McDonald

"A field trial was conducted at an underground gold mine to evaluate diesel fuel derived from soybean oil (soy-methyl-esters or “biodiesel”) as an alternative to commercial, low-sulphur, number 2 diesel fuel (D2). A 2.7 m3, 18-ton load-haul-dump (LHD) unit, powered by a naturally aspirated, indirect injection (pre-chamber), 100 kW diesel engine was used as the test vehicle. The LHD was equipped with a diesel oxidation catalyst. The LHD operated satisfactorily on the biodiesel fuel. Operators observed a slight decrease in power and an absence of black smoke.Diesel particulate matter (DPM) concentrations were monitored for a six-week period while the LHD was operated with either the biodiesel fuel or the D2 fuel. DPM concentrations were measured in the mining section’s clean air intake, exhaust and on the LHD. Reduction in DPM emissions was determined from the measured difference in DPM concentrations between the clean air intake and the exhaust. The biodiesel fuel reduced energyspecific DPM emissions approximately 75%, from 3.6 ± 1.8 g/kW-hr to 0.86 ± 0.27 g/kWhr. Time-weighted average DPM exposure, measured near the LHD operator, was reduced from 0.67 ± 0.13 mg/sm3 to 0.28 ± 0.12 mg/sm3, or approximately 58%, when the biodiesel fuel was used. IntroductionDiesel exhaust consists of noxious gases and diesel particulate matter (DPM). Recent attention has focussed on the potential carcinogenicity of DPM and the potential health impact on miners. The National Institute for Occupational Safety and Health (NIOSH) recommended that whole diesel exhaust be regarded as a “potential occupational carcinogen”, and that reductions in workplace exposure would reduce cancer risks (NIOSH, 1988). The International Agency for Research on Cancer (IARC) declared that “diesel engine exhaust is probably carcinogenic to humans” (IARC, 1989)."

Jan 1, 1997

By C. E. Jordan

The Bureau of Mines conducted research to measure the improvement provided by fine bubbles on the flotation of fine-sized particles (minus 20-um size) in an effort to improve flotation efficiency in our domestic minerals industry. The turbulent velocity distributions of the fluid within the flotation cell were measured as a function of time and position and used to increase the precision of a fine particle, turbulent flotation model. For the mineral system investigated, improved flotation response was obtained under laboratory conditions by using small bubbles and intense agitation. These results matched the model's predicted response.

Jan 1, 1989

By Robert A. Jankowski, Natesa I. Jayaraman, Jay F. Colinet

The U.S. Bureau of Mines evaluated the dust control effectiveness of two-phase flow systems in a full-scale model mine using a mockup of a Joy 14CM continuous mining machine. In a two-phase flow system, air and water flow simultaneously through the nozzle. Air pressure varies from 10 to 60 psi, and water at 30 to 50 psi. Coal dust was introduced at the face, and dust concentrations were monitored at the operator locations and in the return. When compared with a conventional spray system, a symmetrical two-phase flow system reduced dust levels during the box cut by 43 pct at the operator location, and 30 pct in the face return. Dust levels, however, increased at the off-operator position during the slab cut. A directional two-phase flow system reduced dust levels at both operator locations by more than 90 pct in the box cut mode. While the use of two-phase flow systems will reduce respirable dust levels and water usage, it requires an air supply to the miner. Moreover, the ability of the two-phase flow system to redirect the dust cloud makes nozzle orientation a critical factor.

Jan 1, 1991

By B Banerjee, H Masoumi, X Shen, S Raval, D Tannant

Structural mapping of pit walls can be performed using digital images and photogrammetry software, but the performance is limited by weather and environmental conditions including dust, rain and light. On the other hand, active sensors such as terrestrial laser scanners (TLS) and total stations (TS) suffer from vertical orientation bias and occlusions when persistent discontinuities dip at the same angle as the scanner line-ofsight. The recent development of the compact light detection and ranging (LiDAR) systems has made it possible to mount these sensors on unmanned aerial vehicles (UAVs) or drones which offer the potential to overcome limitations that are inherent in existing mapping systems. This study details the research involving integration and application of an advanced UAV-LiDAR system for structural mapping of a highwall. A state-of-the art laser scanner with an inertial measurement unit (IMU) and real-time kinematic global positioning system (GPS) was integrated on to a UAV. The system was first tested in a laboratory condition. Then the UAV-LiDAR system was employed to map a highwall of a coal mine. The planned flight trajectories tested the system at variable distances from the highwall face and at various speeds. The raw data collected from individual sensors were fused, filtered to remove noise, and segmented to produce a surface scan model. Finally, the point density and surface coverage were measured using the surface scan model of the highwall. The parameters were compared with equivalent measurements computed from a reference TLS data. The study demonstrates the capabilities of a UAV-LiDAR system to generate accurate and occlusion free data for mapping highwall geological structure with very quick and efficient flights in the field. CITATION:Raval, S, Banerjee, B, Shen, X, Masoumi, H and Tannant, D, 2018. Evaluation of a UAV-LiDAR system for mapping geological structures in an open pit highwall, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 496–503 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By R F. Sandenbergh

Due to environmental considerations, mineral processing plants are increasingly recycling water to decrease the impacts of wastewater on environment and the depletion of fresh water resources. Industrial experience has shown that increasing recycling water in flotation typically negatively impacts the recovery and selectivity, especially in the selective flotation of minerals from complex sulfide ores. The major reason for the reduced selectivity is typically the inadvertent activation of sphalerite or pyrite by the heavy metal ions (HMI) in solution. These HMI are often produced during milling and flotation and absorbed by other minerals. In the normal flotation pH value range (8 - 10), these HMI are often in the form of precipitates or complex ions that may re-appear in solution or become active should conditions favour this. In this paper, microflotation, batch flotation and XPS surface measurement were used to investigate the use of HMI absorbents additions to the pulp to improve flotation selectivity of a complex sulfide ore. It has been demonstrated that HMI removal does improve flotation selectivity by facilitating more effective depression of the sphalerite. Microflotation and XPS surface measurements have shown that HMI absorbents compete with sphalerite to absorb HMI, and thus reduce the surface concentration of HMI on those sulfides. The practical use of HMI absorbents in complex sulfide ore flotation is also discussed.

Jan 1, 2005

By Chu E. Ho

Key variables that govern the jet cutting process are examined based on fundamental theories of jet hydrodynamics and soil mechanics. Under normal conditions of jet grouting operations, lift speed and rotation speed are found to be of less importance than the depth of jetting, nozzle pressure, nozzle diameter, and the soil bearing resistance, with regards to their influence on jet cutting distance. An analytical equation linking the governing variables is proposed, which allows for the possibility of evaluating column diameters achievable in different ground conditions based on theoretical calculations. When used in conjunction with shallow jet grouting field trials, the equation can provide a means for extrapolating trial results to conditions at actual depths for production jet grouting.

Jan 1, 2006

By C. G. Bastos Andrade, V. F. Justo, F. R. Valenzuela-Diaz, M. G. S. Valenzuela, C. M. Matos, C. Volzone

For industrial use, the smectite clays are usually treated with inorganic acid of high concentration at temperatures under boiling point, which provide the bentonite´s bleaching power. In the present paper, a sample of brown smectite from Paraiba, Brazil, was submitted to treatment under moderate conditions (90°C, reaction times of 1, 6, 12, 18 and 24hours in close reactor, concentration of the aqueous solution of hydrochloric acid 1.5M, clay/acid solution ratio of 1g/10mL), aiming to reduce impurities, responsible for the color of the clay, without causing significant changes in their structure. The samples were characterized by scanning electron microscopy (SEM), energy dispersive X-ray detector (EDS), stereomicroscopy, Cation Exchange Capacity (CEC), Thermal Analysis (TG/DTA), and X-ray diffraction (XRD). It was observed a bleaching in samples with time of 12h to 18h. With the DRX was possible to monitor the peak intensity of the clay structure and the sample with 12 hours of treatment was not significantly altered its crystalline structure, maintaining the peak clay at d(001). The most pronounced changes in the bleaching occurred within the first 12 hours of acid treatment. Thus, clay can be used in products with high added value.

Jan 1, 2015

By Matthew S. Sanchez, Richard J. Lee, Matthew D. Zock, Drew R. Van Orden, Yumi Kamiya, Edward B. Ilgren

In many developing countries, asbestos is still used for friction products, insulation, and asbestoscement products. However, there is very limited modern data evaluating the airborne concentrations of asbestos fibers in operating asbestos plants. We have conducted an Industrial Hygiene survey, using state of the art PCM and TEM analysis, of a Bolivian asbestos cement plant that uses crocidolite during the production of roofing shingles and water tanks. The study is the first to use modern analytical measurements in an uncontrolled asbestos environment. Thus, this study offers insight into the historical airborne exposures at asbestos plants operating before modern dust control measures were introduced or airborne fiber levels regulated. The results suggest that fiber concentrations are far in excess of those for which current models would predict the onset of asbestos disease and mesothelioma. Significantly, the plant and community do not have an elevated incidence of asbestos disease or mesothelioma. Airborne fiber levels during comminution and fiber sizing ranged from 100 to as much as 1,000 f/cc. Fiber levels in the mixing, forming and finishing areas ranged from 0.5 to 9 f/cc. Based on the number of overloaded samples and estimates of their concentration, historical estimates of exposure may be underestimated by an order of magnitude. Also, an excellent correlation (1:1) between the PCM and TEM fiber concentrations (for fibers _0.25 um diameter) were obtained, raising questions about the conventional wisdom that the PCM systematically undercounts fibers. The results of this study further indicate that current models may overestimate the risk of asbestos disease and mesothelioma.

Jan 1, 2012

By L. Naude, J. Cloete, S. Engelbrecht

The results of an investigation evaluating whether an industrial plant, currently operating using sodium isobutyl xanthate (SIBX) as primary collector for sulphide minerals (mainly chalocopyrite), could adapt to operate using an alternate primary thiol collector without compromising plant and metallurgical performance. Initial laboratory scale flotation tests identified commercial dithiophosphate (DTP)-based and thionocarbamate (TC)-based collectors, that when blended, showed potential to replace the incumbent SIBX primary PGM collector. Industrial plant trail results show that there was no deterioration in recovery of 4E PGMs, even at a lower concentrate grade when operating the plant on the identified (DTP + TC)-based collector blend compared to SIBX. The effect on Cr2O3 content in the final concentrate was also found to be negligible. The (DTP + DTC)-based collector blend also showed promise in terms of plant adaptability in accommodating a new primary specialty collector blend. These observations highlighted the potential of replacing xanthate primary collectors with alternate thiol collector blends for PGM flotation. Keywords: PGM, xanthate replacement, specialty collector, sodium iso-butyl xanthate (SIBX), dithiophosphates (DTP), dithiocarbamates (DTC)

Jan 1, 2020

By Yuting Xue, Todd Minoski, Daniel Su, Mark Van Dyke, Mark Mazzella, Steve Hicks, Zoheir Khademian, Nicole Evanek

Design of chain pillars in a longwall mine setting is one of the main engineering controls on the global and local stability of the mine. Challenges with roof instabilities, floor heaves, and pillar failures can be alleviated, to some extent, by careful design of gateroad configurations and chain pillars. This work investigates three different alternative designs in a three-entry-system gateroad configuration with an inter-panel barrier in a longwall mine in Virginia. Starting with the current design, which has faced challenges such as excessive floor heave, a geomechanical model developed in 3DEC software is validated by monitoring in-situ pillar stress in the yield, abutment, and barrier pillars in the mine. Next, three different chain pillar designs are evaluated in the model with a focus on roof sagging, floor heave, and pillar average stress. Results show the relationships among the alternative designs and instabilities associated with roof, pillar, and floor in the study mine, providing insights for optimizing longwall mining designs in deep-cover settings.

Feb 1, 2025

By J. A. Herbst

Fine coal cleaning by froth flotation has become common practice in the U.S. with more than 80,000 tons treated in this way per day. In spite of this large tonnage, developments in the automatic control of coal flotation circuits have lagged significantly behind those for mineral systems. One reason such developments have been limited is that instruments have not been available for the on-line measurement of carbon or ash and another critical variables in coal slurries. A second reason is that the influence of the operating variables on coal flotation has not been completely understood. During the last few years some of the required instrumentation has been developed and an improved knowledge of the flotation process itself has occurred through mathematical modeling; as a result certain control strategies for coal flotation are beginning to emerge. This paper attempts to evaluate several control strategies using a detailed flotation dynamic simulator, DYNAFLOAT. After constructing a process matrix for the system of interest, promising alternatives for linking manipulated and controlled variables have been analyzed. In order to develop combined grade and recovery control strategies, the authors found it necessary to construct a grade/recovery map with the aid of the simulator to drive the system to known final, feasible grade/recovery operating conditions. Finally, an advanced strategy which uses an on-line model to identify disturbances and take control actions is proposed.

Jan 1, 1983

By Jeroen van Eldert, Daniel Johansson, Henrik Ittner, Håkan Schunnesson

"Numerous aspects of underground construction, from structural stability to construction costs, depended on the tunnel quality, including blast damage and the Excavation Damage Zone. Accurately quantifying the extent and severity of damaged rock is a problem. Recent technical developments in the field of Measurement While Drilling (MWD), including software for on-board logging and on-site analysis, have shown potential for rock-mass characterization. Ground Penetrating Radar (GPR) and P-wave velocity measurement have also improved and show similar potential. This paper explores the use of MWD, GPR and P-wave velocity measurements and uses them in techniques for excavation damage characterization and prediction. The paper is based on data collected from a small underground waste-collection site in central Stockholm, Sweden. The data is correlated against rock-mass characteristics and their responses are evaluated. Results indicate potential for excavation damage characterization for all tested techniques, which could minimize blasting damage and improve the over-all tunnel quality. 1 INTRODUCTION During underground excavation the rock mass is influenced in many ways. The Excavation Damage Zone (EDZ) is a result of these influences. The EDZ can be defined by an irreversible change in rock mass properties, for example increased permeability. EDZ is influenced by the excavation method, the rock mass properties and the in-situ stresses in the area of the tunneling. Since the 1990s research has been done on the EDZ by Emsley et al. (1997), Christiansson et al. (2005), Olsson et al. (2009), Ouchterlony et al. (2009), Ittner et al. (2014), and Siren et al. (2015). Based on past literature the EDZ have in this paper been separated in the following subzones: 1. Failure Zone or over-break is the area outside the planned tunnel profile, including the Look-Out and hole deviation. This zone consists of fracture networks (both natural and blasting-induced), that caused rock fall-outs. The extent of the over-break can be determined by volumetric scanning and photogrammetry and the half cast factor can be used as a damage indicator. 2. The Damaged Zone is split into three parts and but the quantity and depth of damage is difficult to measure. Although it can be visualized by sawing of rock slices in the tunnel wall (Olsson et al. 2009), diamond coring (DC) or P-wave velocity reduction (Jern 2001): a. Inner Damage Zone (Crush Zone): It is located directly around the drill hole, and is caused by the shock-wave energy of the detonation. The micro fractures in the Crush Zone produce a white-wash (rock dust) in the half cast. b. Transition Zone: This zone consists of micro fractures that connect and form macro fractures, both radially and parallel to the tunnel wall. The macro fractures are caused by the gas expansion during the detonation of the explosive; it increases the pressure in the (micro) fractures and creates the macro fractures. Seismic reflection, rock slicing and core drilling can be used for the examination. c. Progressing Zone: In this zone the existing radial fractures propagate due to the increase gas pressure inside these macro fractures. Examination methods are seismic reflection, rock slicing and core drilling. In addition, the Peak Particle Velocity (vibrations) could be used to estimate the depth (Tesarik et al. 2011)."

Jan 1, 2016

By Philip Morey

Large scale surface coal mining will be required to fill future energy demand in the United States. In realization of this long-term commitment to coal resources, the U.S. Energy Re-search and Development Administration sponsored a study to determine the costs and problems of large-scale surface coal mining. As a result of this study a series of computer models were developed that can be used by government and industry to: 1) facilitate mine design and equipment selection, 2) provide detailed analyses of mining and processing costs. Two types of models were developed: detailed simulation models, which provide detailed information on mining systems and equipment to assist in mine design and equipment selection1 and broad models, which provide a first-order evaluation of deposits and new ventures for an entire mining complex. The complete model series permits examination of surface coal mining under a variety of terrain conditions. Six different mining methods were analyzed and documented during the overall project: 1) Area stripping with draglines, 2) Area stripping with draglines, extended bench, 3) Contour stripping with draglines, 4) Area stripping with shovels (loaders) and trucks, 5) Mountain top removal with shovels (loaders) and trucks, 6) Multiple dipping seam mining with shovels (loaders) and trucks. Each major operation in the coal mining pro-cess is represented in these models so that the best methods and equipment may be selected and 50 that the impact of such selection will be reflected in estimates of capital investment, operating costs, and coal price. Individual models allow the user to separately analyze overburden removal, overburden drilling and blasting, coal drilling and blasting, coal loading and hauling, coal preparation and handling, land reclamation, and premining, facilities, and administrative expenses. Because it is impossible to cover all the models in this paper, only the detailed simulation models representative of the technique "area stripping with draglines," are described. The Fort Union Strippable Coal Resource Region, one of eight test cases, is used as an example to describe the models.

Jan 1, 1978

"A commercially available through-the-earth (TTE) communications system was evaluated at an active underground longwall mine in West Virginia. This TTE system uses electricfield (E-field) sensing to send text-based communications through two separate antenna arrays connected in parallel. Each antenna array is composed of interconnected, grounded metallic rods or other such structures. Two-way communication between subsurface locations was investigated in this study using various antenna configurations. This field study was conducted as a part of a larger multisite evaluation of available TTE systems in an effort to determine their operational sensitivities. IntroductionWireless, through-the-earth (TTE) communication technology is designed to achieve point-to-point communication through solid strata using very low frequency (VLF) and ultra-low frequency (ULF) electromagnetic waves. Using this approach, communications are established without the need for intermediary communications infrastructure. As a result, TTE systems have the potential to provide reliable, robust communications between surface and underground personnel. Exploration into the use of TTE technology for this purpose dates back to the 1920s (Jakosky and Zellers, 1924; Pittman, Church and McLendon, 1985), but U.S. permissibility requirements slowed the development of TTE equipment for widespread implementation (Durkin 1980; Pittman, Church and McLendon, 1985). One of the primary challenges in producing wireless TTE communications is the counteraction of signal attenuation when propagating through solid strata (Barkand, Damiano and Shumaker, 2006; Wadley, 1949). The long wavelengths of TTE transmissions make them well-suited for reducing the rate of attenuation. However, even when operating within the VLF to ULF range, the performance of TTE systems is still affected by geologic and anthropogenic factors (Geyer, 1973; Geyer and Keller, 1976; Geyer, Keller and Ohya, 1974; Jakosky and Zellers, 1924; Large, Ball and Farstad, 1973). Although commercially developed TTE systems have demonstrated the ability to communicate in a variety of conditions, their range and performance have been highly varied (Barkand, Damiano and Shumaker, 2006; Geyer and Keller, 1976; Geyer, Keller and Ohya, 1974; Ilsley, Freeman and Zellers, 1928; Jakosky and Zellers, 1924; Yenchek et al., 2012)."

Sep 1, 2016

By W. C. Smith

Over the past several years, the Bureau of Mines has conducted studies on the performance of fully grouted resin bolts In underground mines. The effectiveness of resin-grouted bolts in maintaining a competent roof, even in weak rock, has been well documented in the literature. Recent Bureau studies have evaluated the affects of shortened grout columns on bolt behavior in a variety of rock types (1, 2, 3). The application of partial grout columns to primary roof support systems has been introduced as a viable alternative to fully grouted bolt systems in some mines. The point-anchored resin bolt and combination bolt represent such alternatives. While both systems usually employ some mechanical interlocking system, their primary difference lies in the length of resin column used. Point- anchor systems rely on an anchoring device that is a short length of resin column of 2 feet or leas. Combination bolts, on the other hand, often require 3 feat or more of resin column. Resin migration into voids and fractures intersecting the borebole wall is a major problem when installing fully grouted bolts in weak roof rock and can result in a reduced column length that provides reduced anchorage. The relationship between column length and anchorage integrity deserves closer study. The Denver Research Center of the Bureau of Mines has examined the load- carrying capabilities of resin-grouted bolts in weak strata. Pull tests were performed on about 900 resin-grouted, 4- foot-long bolts with column lengths ranging from 6 to 48 inches. The practical performances of 8 different column lengths were evaluated for 10 mines under in sit" conditions using data obtained from standard pull tests. In addition criteria are discussed, including engineering properties of the host rock for designing safer and more effective grouted bolt installations.

Jan 1, 1987