Search Documents

By Leon McCulloch

WHEN clean iron and metallic zinc dust, protected from the air, are heated below the melting point of zinc, the iron takes on a coating that has excellent protective value. This coating is a brittle alloy of zinc and iron, and the process is called sherardizing. Although the zinc particles are covered with oxide and cannot touch the iron, an extremely small amount of the zinc vaporizes and the vapor, reaching the iron, alloys with it. Other zinc then vaporizes to replace that which has been removed from the atmosphere. This process continues indefinitely at a decreasing rate, for the coating already formed permits zinc to diffuse through-it to combine with the iron beneath. In this way, the coating grows outward from the surface of the iron, as the bark grows from a tree. The method of growth was clearly seen while sherardizing small cubes of cast iron, at about 450° C., in a small glass-stoppered bottle enclosed in a rotating drum. The dust contained about 3 per cent. iron, which prevented caking, and coatings 1/2 in. thick were grown in a few hours. After a heavy layer had been formed, the cubes were again: treated for a shorter time. The layer last formed was seen to lie next to the iron, instead of at the outer surface, showing that the growth was from the surface of the iron outward. The coatings split at the edges and corners, leaving the iron exposed there. Flakes of graphite from the iron were lifted upward and embedded in the coatings. The composition of sherardized coatings varies from the outer surface inward, as would be expected from the mode of growth. That is, the iron content increases slowly at first, then more rapidly as the iron is approached. At the surface the least amount of iron possible is 6 per cent., as the experiments described below have shown.

Jan 2, 1922

By J. E. Golsan

Barrick Gold Corporation installed an expert style control system on the grinding circuit at its Mercur mine. Barrick's main objective was to increase mill throughput by a minimum of 3%. The expert system team collected operating data and then created a knowledge base using Comdale/X expert system development software. The expert system moved from on-line "advisory" mode, testing of expert rules, to full process control in four weeks. Expert system control benefits include a 9-15% increase in mill throughput, consistent mill loading leading to less wear on SAG mill parts, and improved downstream process control.

Jan 1, 1998

By Luis Bergh, Juan Olivares, Juan Durán, Juan Yianatos

"In the last decades heuristic approaches based on logic rules have been one favored tool to control flotation units and plants on top of distributed control systems. Fundamental knowledge on flotation processes, expressed in reliable models, and programs to assure the quality of the information, contained in available measurements, are still insufficient to develop robust predictive control strategies. In this paper the idea of using simplified models, when a known disturbance is coming into the process, is explored. As a first approach, the set points of the froth depth and air flow rate controllers are estimated based on this model. Since these target predictions are only approximate, a conventional feedback expert system, based on logic rules, continues the task of calculating the set points of the distributed controllers, in order to decrease the gap between actual and desirable metallurgical targets. This combined actions permitted a fast response of the process to change the operation of the circuit when a measured disturbance is detected. This control system was implemented and experimentally evaluated in a pilot rougher flotation circuit, with three pneumatic cells, with froth depth and air flow rate controllers in each cell. Since the circuit is operated for the air-water system, a phenomenological model, with parameters estimated from industrial data, is fed on-line with real operating variables and virtual values, characterizing the feed (grades, solids%, particle size distribution), in order to predict the metallurgical targets (recovery and concentrate grade). Several cases are discussed showing the benefits of this control system and the possible improvements to work on. INTRODUCTIONToday, large size mechanical flotation cells of 100 to 300 m3 are used in rougher operation in different flotation industrial plants, in Chile and worldwide. However, in spite of the advances in fundamental research and the notable growing in equipment size, with more complete instrumentation systems, there are still a lack of reliable data for industrial flotation modeling and simulation to advance in better control systems design."

Jan 1, 2016

By Ebrahim F. Salmi, Tan Phan, Ewan J. Sellers, Thomas R. Stacey

Extension of ore pass length has become increasingly critical for optimising energy-efficient underground mining operations. Long and ultra-long ore passes, spanning from 300 to 700 m, can significantly improve the functionality and viability of underground mass mining operations though suboptimal performance has an extremely adverse impact on production. The public domain lacks substantial information regarding the primary engineering, geological, and geotechnical risks and challenges associated with the design, implementation, operation, and maintenance of such long ore passes. Therefore, the aggregation of past experiences and the insights of experts assume paramount significance. An innovative methodology is introduced to address this evident data deficiency and to establish comprehensive guidelines for the resilient design of such lengthy ore passes — combining gap analysis with expert elicitation techniques. This equips design engineers with the necessary tools to formulate and adapt strategies for assessing the numerous challenges and uncertainties that invariably accompany their projects. Expert elicitation techniques are summarised, and a gap analysis is conducted with subject matter experts, from various countries, collating their extensive ore pass design experience, to create a comprehensive list of effective parameters and key risks that must be considered. Quantitative analysis of the survey results enabled the identification and ranking of the numerous factors affecting the design, operation, and maintenance of long and ultra-long ore passes and highlights the complex technical challenges (substantial damage from rock particle impact, increased dynamic mining stresses leading to failure, air-blasts and back blasts, dust, preferential flow, turbulent and dynamic material flow) that are uncommon in shorter ore passes. Additionally, increasing length heightens the probability of intersecting weak rock or discontinuities, leading to a higher risk of structural failure and instabilities. Faulting, folding, and large-scale structures are also critical geological factors to be considered in the design of such structures. The key geotechnical factor is also the rock type surrounding the pass. Experts highlighted the lack of clear guidelines for decision-making, resilient design, and construction so this work suggests future investigations to determine the complex interaction between the effective parameters, using approaches like the rock engineering system, discovery of cascading hazards, and optimal controls.

May 3, 2024

It's my privilege to welcome you here this afternoon on behalf of the Sydney Branch of the Australasian Institute of Mining and Metallurgy. This is a most important gathering. You, the delegates, represent what is probably the most influential cross-section of the mining investment community and the oil and gas investment community to meet as a group during the last decade. We are meeting today and tomorrow to review two related issues that will have far reaching implications for the effective use of capital by the natural resources sector in the 1990's. The views which will emerge over the two days will almost certainly 'influence the availability of new capital to the companies in the natural resources sector for the decade ahead. The two principal themes of Minval '89 are, first, the valuation of mining and oil and gas assets and securities, and second, disclosure and reporting requirements in the capital markets which relate specifically to natural resources companies. This conference is taking place at a time when further consolidation and rationalisation appears likely within the mining industry. Although the base metals and other sectors of the industry are enjoying profitability not seen since the early 1980's there is caution about committing to new capacity which could bring about a return to the low prices and excess supply which prevailed during much of the last ten years. These conditions have led to increased takeover activity within the mining industry overseas, and similar trends are as evident here in Australia as they are elsewhere. Recognition of value is therefore likely to become more important than ever before in preserving shareholder wealth, for creating new wealth and for preserving the financial health of the resources industry in the future. Valuation therefore is the first theme of the conference.

Jan 1, 1989

By D. Sinha

Mine investment decisions involve both objective and subjective criteria. The subjective criteria are efficiently decided by interaction with company experts. The Expert System approach can incorporate knowledge of experts and interact with conventional computer programs on mine evaluation. Artificial intelligence offers considerable opportunities in comprehensive mine investment decision making process.

Jan 1, 1998

By Xuling Chen, Yi Wang, Xiaohui Fan

"The current control method of grate-kiln iron ore oxide pellet production is lack of accuracy and normalization due to the limited detection conditions. Therefore, mathematical models of grate-kiln temperature field are presented. With calculation of gas-particle heat transfer as well as enthalpy changes of moisture evaporation and magnetite oxidation, the thermal history of pellets throughout grate-kiln process can be acquired and used for production status estimation. Taking the calculated results as well as detected data in production as inputs, process parameters such as running speed, fan opening and coal injection rate as adjusting objects, expert system for grate-kiln pellet production is outlined. And the preheating section dominated control strategy is explained. Results of production application show that the stability rate of gas temperature in gas hood of preheating section is increased from 91.0% to 94.2%, compressive strength and first grade rate of pellet are increased by 3.62% and 2.36%, respectively, while FeO content is 18.18% lower. Control guidance of this expert system can solve production anomalies effectively, stabilize grate-kiln iron ore oxide pellet production and improve pellet quality.IntroductionSteel industry in China has developed rapidly in recent years. China’s crude steel production in 2010 is nearly 627 million, which is 44.2% of the world total production. Burden with higher quality is demanded by enlargement and modernization of blast furnaces. And oxide pellet production has become a growing concern. In 2010, the total production of pellet in China is 110 million, and about 60% is produced by grate-kiln process."

Jan 1, 2012

By J. L. Kohler

The knowledge-based expert systems (KBES) is a potentially powerful technique to the mining engineer in traditional areas of mine design and operations, as well as in the emerging areas of mining automation and robotics. Since KBES is still experimental in many respects, caution must be exercised as this "high tech" tool is developed and applied to mining. The objective of this paper is to demystify expert systems by introducing the elements of KBES, discussing the strengths and weaknesses, and identifying some areas of application in mining, based on the authors' experiences.

Jan 1, 1986

By R. L. King

An expert system is a computer system that performs tasks that are considered by most people to require human expertise. Since their functioning relies heavily on large bodies of knowledge, they are often referred to as knowledge-based systems. These systems can contain the skill and knowledge of an individual human expert or the combined knowledge of a group of experts. The knowledge embodied in an expert system can consist of specific facts, HSHA regulations, heuristics or rules-of-thumb used by the expert, and databases. The purpose of this paper will be to introduce the participants in the ?Increase Competitiveness Thru Innovation? session to expert systems. This introduction will enable the participants to better appreciate the balance of the papers to be presented in this session. These papers will deal with specific mining problems and a proposed innovative solution. This paper will discuss such topics as problem-solving paradigms, rules of inference, knowledge representation, and the structure of expert systems.

Jan 1, 1989

By Steve Kral

Mining is a risky business. The cost of exploring for new mineral deposits is high and the success rate of finding one worthy of development is relatively low. And once a deposit is identified, there is no guarantee that it will become a mine. Mining companies have to spend a lot of time and money on due diligence, prefeasibility and feasibility studies, and sustainable development and environmental issues before deciding whether the deposit will become a profitable mine. And then there are the millions of dollars spent in developing the deposit and building a mine. No wonder the mining industry has trouble attracting investment capital. Companies take a large risk in developing reserves and investors take a similar risk in investing in them. So mining companies must be as accurate as possible in determining mineralization that makes it to reserve status. After all, reserves are a company’s most important asset and one of the critical factors analysts and funding sources look at when determining if a mine or mining company is worth the risk.

Jan 1, 2003

By C. A. Rowland, R. C. Nealey

Wet grinding rod mills have been used for 50 years to grind ores and to make specification sand. The application of wet grinding rod mills is well understood. Until recently, there have been very few installations of dry grinding rod mills. The selection of dry grinding rod mills follows the basic principles established for the selection of wet grinding rod mills. The basic Bond Formulae1 [ ] is used to select mills when using grindability test results as the basis for selection. W is multi- plied by the 1.3 wet to dry grinding factor established from wet and dry ball milling experience, and then by any other applicable inefficiency factors.1 Dry grinding rod mills have also been selected by scaling up bench scale continuous rod mill tests and pilot plant tests.

Jan 12, 1968

By M. Pierce, E. Karampinos

"One of the main challenges in the numerical modelling of ground support in underground excavations is to reproduce the performance of the sequential installation of the reinforcement while capturing the rock mass behaviour of an advancing face in 3D. The 3D modelling approaches used to simulate the progressive advance of excavations are mostly continuum and often cannot reproduce the rock mass failure mechanisms. The 3D discrete element method (DEM) can better reproduce structurally controlled rock mass failure mechanisms and can explicitly represent the reinforcement elements. This paper builds on previous work that reproduced the structurally controlled squeezing conditions in an underground hard-rock mine using 3D DEM and the in situ behaviour of reinforcement under pull conditions. It addresses important issues on the way reinforcement is explicitly introduced in discrete element models. A pseudo-3D model is employed to overcome the computational restrictions and time limitations of a 3D modelling approach. The work focuses on the scaling of the material properties of the ground support elements when the thickness of the model is not equal to the out-of-plane spacing of reinforcement. It demonstrates the scaling methodology based on the type of the modelled reinforcement elements used and investigates the significance of this approach. The advantages and disadvantages of this approach with respect to 2D and 3D methods are discussed. The results are compared with field data and previous modelling work done at the mine. IntroductionNumerical models can provide significant insight into the anticipated behaviour of underground excavations. The modelling of ground support, however, is not a trivial exercise. An effective representation of ground support in underground excavations should capture the behaviour of both the rock mass and the support elements. When numerical models are used for design purposes, the complexity of the problem requires significant time and expertise (Sweby, Dight, and Potvin, 2016).At a laboratory scale, numerical models have successfully reproduced the results of laboratory tests on rockbolts by explicit modelling of the bolt, the borehole, and the grout. Chen and Li (2015) used a continuum FLAC3D (Itasca Consulting Group Inc., 2012) model to simulate the mechanical behaviour of D-bolts as observed experimentally. Grasselli (2005) used a 3D finite element code to model the behaviour of fully grouted rods and expandable bolts under shear."

Dec 1, 2018

By D. Song

In this paper, the differential equations governing the mass transport and the electrochemical reaction in a cathode catalyst layer of polymer electrolyte membrane fuel cells are solved based on the polynomial series expansion method. Explicit expressions for the polarization curve as well as for the distributions of oxygen, current density and overpotential are obtained when a quadratic, cubic or quartic polynomial is employed to approximate the oxygen concentration distribution. These kinds of explicit solutions are desirable for MEA design and diagnosis purposes. The comparison between the conventional numerical approach and the explicit solution approach proposed here shows that satisfactory accuracy can be reached by the first four terms of the polynomial series. The effect of the catalyst layer thickness on the accuracy of the obtained explicit polynomial solutions is also discussed.

Jan 1, 2005

By M Freeman

In a visionary move, the Planning Commission and the Ministry for Planning in Western Australia decided to invite three extractive industry quarry operators, local government councils and State Government departments (Minerals and Energy, Environmental Protection, South West Development Commission) to contribute jointly to study the impacts of blasting on areas surrounding basalt quarries in the Bunbury region of WA. The results of the study will help establish suitable zones in which land uses will be controlled under a proposed Greater Bunbury Region Scheme and in local planning schemes, to minimise conflicting land uses. This paper discusses the blasting program conducted to characterise and model the vibration behaviour of the rock under the effects of pilot-scale and full production blasting, and highlights some of the benefits achievable when a thorough blasting impact program and assessment is conducted at the planning stages of land-use establishment.

Jan 1, 2001

By P. V. Ramesh Babu

India has sizeable number of small deposits of rare metal bearing minerals namely columbite-tantalite, pyrochlore, beryl, lepidolite, spodumene and rare-earth element bearing minerals monazite and xenotime in different parts of India. Pegmatites, alkali granites, syenites, and the derived gravel and soils are the main source for rare metal and rare earth (RMRE) minerals. The RMRE minerals are classified as prescribed substances under Atomic Energy act of 1962 keeping in view the uses in the nuclear industry. Atomic Minerals Directorate for Exploration and Research (AMD) of Department of Atomic Energy (DAE) is the sole agency responsible for exploration and exploitation of RMRE minerals in India since 1962. The latest technological advancements and applications in the field of space, electronics, communication and nuclear industry using these metals and their products have necessitated to augment the production and resources of RMRE minerals. These minerals play a significant role in the technological and economic development of the country. The light rare earth element bearing mineral monazite is abundant in beach sands and is being commercially exploited by Indian Rare Earths Limited (IREL). Columbite-tantalite, the chief source for niobium and tantalum (Nb-Ta) metals present in the pegmatitic gravel are recovered by small mobile beneficiation plants. The cut and fill method of mining adapted is eco-friendly. The processing flow-sheet consists of wet sizing at ½ in and 1mm followed by gravity concentration of sized products utilizing the methods of jigging and wet tabling. The sizing equipment include revolving and vibratory screens and the gravity concentration equipments used are fixed sieve jigs and movable screen jigs for final upgradation. The gravity concentrates are further upgraded by magnetic separation to remove magnetite and ilmenite. The mine areas are reclaimed by filling with coarse size tailings and new plantations. These mobile pilot plants were earlier operated in Bihar mica belt, Jharkhand, pegmatitic areas of Karnataka and Nellore mica belt of Andhra Pradesh and are currently being operated in Bastar-Malkangiri pegmatite belt of Chhattisgarh and pegmatites of Jharsuguda district of Orissa. Beryl, lepidolite, spodumene and cassiterite minerals are the by-products from the pegmatite ores. Fergusonite, samarskite and microlite are the other niobium and tantalum bearing minerals which are also found in pegmatites. Xenotime, the chief mineral of yttirium generally occurs in granites and pegmatites. The rare earth minerals monazite and xenotime get concentrated in the placer sands of rivers and beaches. The occurrence of xenotime in the sands of Siri River and Deo River in Chhotanagpur granitic terrain in parts of Chhattisgarh and Jharkhand are an example. These sands containing 1-2.5% heavy minerals were processed by a mobile plant consisting of sizing equipments like trommel and vibratory screen followed by separation of heavy minerals from -1mm sands with the help of gravity concentration equipments like spirals/shaking tables/sluices. Xenotime and monazite from the pre-concentrate are further separated by magnetic and electro-static methods. The present paper illustrates the pilot plant set up for the recovery of rare metal as well as rare earth minerals. Keywords: small deposits, rare earths, rare metals, pegmatite, Nb-Ta, xenotime, India

Sep 1, 2012

By E P. Graham

Orebodies occur in an infinite variety of grades, shapes and sizes, and take many millions of years to grow. When extraction starts there is only one possible end -the mine sooner or later will run out of ore and shut down. If the mineral industry is to supply the ever increasing demands of modern civilizations, more and more metals must be found and mined. This will require a never-ending search for ore, and the development of every economic body, large or small. To justify the mining of a small orebody, it first of all must pay its way. If the size of the burden imposed by the capital cost estimates is not carefully worked out, an otherwise promising situation could be killed. The very nature of mining, as a transient industry, re-leases a steady stream of good used equipment, and the trained personnel to install and operate it. All manner of plans and layouts, which can be utilized at a new property, are available. Working these and other economies into the estimates will sometimes make enough difference to give a prospect the green light.

Jan 1, 1964

By D A. Aitzhanova, E Zh Omirzakova

The Republic of Kazakhstan has well developed mining and metallurgical complex. In modern conditions, when deposits of useful minerals are running thin, it is very important to find additional sources for obtaining necessary products. As our investigations showed different kinds of waste may be used for producing of different kinds of products, which are successfully applied in different branches of KazakhstanÆs economy. Analysis of ways for increasing of complex use of mineral raw materials of different deposits, widening raw mineral materials base and decreasing negative effects on the environment, are presented in this paper.

Jan 1, 2003

By G. Ordaya

Antapaccay pertenece a un depósito tipo pórfido skarn - stock work sedimentario de cobre (oro-plata-molibdeno), ubicado dentro de la franja Eocena-Oligocena en Yauri-Andahuaylas. En ese sentido, el presente texto señala el proceso de exploración desarrollado para incrementar los recursos a tratarse, considerando una alteración propilítica y que en profundidad se haya encontrado la misma roca como alteración potásica con algunas fallas que han ascendido la mineralización económica. Para tal proceso, se empleó el uso de herramientas geológicas como el cartografiado de detalle en afloramientos, relogueo en detalle, reinterpretación en secciones y bancos para la concepción del nuevo modelo geológico.

Jun 1, 2013

"Chairman: Dr DeV. HarrisRapporteur: Mr A.H. MunroPapers:Corporate exploration strategies by MacKenzie, B.W.The Engel Simulator and the search for uranium by Griffiths, J.C. and Singer, D.A.The Chairman opened the session by tracing the changes which have taken place in the exploration field since the days of the lone prospector who relied upon his individual skills and to a large extent on luck. The deposits which now remain to be discovered are better covered and are of lower grade. A much greater team effort, involving geoscientists and engineers, is required. The gamble is thus much greater -not only are the probabilities of failure still significant but the consequences are more severe. A recent Canadian survey indicated that expenditures of between two and nine million dollars on regional exploration programs are required to locate one significant deposit.The Chairman went on to say that these facts have led companies to regard exploration as another form of investment and to treat it accordingly. This had placed exploration in the context of corporate strategics and structures, which was the subject of the first paper of the session.In introducing his paper, Dr B. W. MacKenzie said that the paper suggested a decision framework for exploration planning. Initially the environment is analyzed to define observable and relevant economic characteristics. The terms of reference for exploration planning and the appropriate allocation of capital and skills are then established in the light of corporate objectives and growth alternatives. With the aid of this information and in the light of profit and corporate risk criteria, exploration strategies can be selected.Dr MacKenzie went on to say that the usefulness of the concept and criteria outlined in his paper depended critically upon three characteristics of any particular economic environment, namely, the return resulting from an economic discovery, the unit discovery Cost and the probability of making an economic discovery. He then showed by means of a case history relative to the Canadian Shield and Cordilleran areas that these three characteristics could, in fact, be evaluated for regions with reasonable histories of mineral activity.The first contributor to the discussion of the paper, Mr Alfred Weiss, mentioned that his group had been involved in exploration modelling for some ten years and were thus particularly interested in the paper. He went on to say that they had experienced greatest difficulty with reconnaissance programs and that he sensed that these difficulties were also present with the methodology which had been outlined. Mr Weiss asked Dr MacKenzie how he would deal with such situations when no information was available but where there was the potential for both exploration and discovery. Dr Mackenzie agreed that the lack of information was a very severe limitation and said that at the present time his methodology probably did not provide a basis for breaking down the broad geological regions he considered into areas for further assessment."

Jan 1, 2014

By D. R. Wilburn

The worldwide budget for non fuel mineral exploration was expected to increase by 27 percent in 2003 from the 2002 budget, according to the Metals Economics Group (MEG) of Halifax, Nova Scotia. The increase comes after five years of declining spending for mineral exploration. For the first time in several years, all regional exploration budget estimates for 2003 as defined by MEG would increase from similar 2002 estimates. However, MEG included 193 more companies in its 2003 survey than in 2002. As with previous MEG survey reports, estimates reflect anticipated expenditures rather than actual dollars spent. Caution, therefore, must be taken when comparing 2002 and2003 estimates or evaluating the magnitude of regional changes from year to year. Sample variations and currency exchange rates may influence year-to-year variations of MEG data. Even so, it is likely that the general climate of improved metal prices in 2003 encouraged companies that had previously left the mineral exploration sector or reduced their exploration activity to once again focus on minerals exploration or increase exploration activity and budgets.

Jan 1, 2004