Search Documents

By Phillip Philbin, Frank E. Senftle

A field neutron activation analysis technique suitable for determining uranium in ores has been tested. The method is based on the measurement of the 74.7 keV gamma ray from 'U. When the thorium/uranium ratio is greater than one or the vanadium is greater than 1%, a low uranium analysis is obtained. No satisfactory correction for thorium has been found, but a correction for vanadium can be deter¬mined. For ore containing greater than 0.01% uranium, the uranium can be deter¬mined with an accuracy of about 10% which is quite adequate for a field exploration technique.

Jan 1, 1972

By Shad M. Sargand, Manseok Chang, Glenn A. Hazen

Customarily, peak particle velocity of surface wave vibrations has been the recommended criterion for the prediction of blast damage to structures. Currently blast spectrum and natural frequencies of a structure have been also recognized as important for predicting damage potential. While others have considered the importance of structural frequencies, they have not analyzed the structural response spectrum when establishing damage criteria.

Jan 1, 1992

A series of field and laboratory evaluations were conducted in order to characterize the effects of a Mann+Hummel SMF-AR® diesel particulate filter (DPF) system on the aerosols and criteria gases emitted by diesel engines. This system, with a durable sintered metal filter media and available active regeneration via an on-board electrical heater, has been considered for retrofitting diesel engines used in light- and medium-duty underground mining applications. Two DPF systems were installed on a forklift and locomotive from the underground mining fleet of the Vale?s Creighton Mine and evaluated over a 1,500-hour trial. This evaluation was complemented with field and laboratory emissions tests. The field tests were performed on the vehicles while at the Creighton Mine surface shop. During those tests, the emissions were assessed for the engines operated at hydraulic stall, high idle, and low idle conditions. The laboratory tests were executed at the diesel engine emissions laboratory at the National Institute for Occupational Safety and Health (NIOSH), here the DPF removed from the forklift was further evaluated at four steady-state engine operating conditions as well as at transient conditions using a custom-designed duty cycle. Very similar methodologies were used during field and laboratory tests to measure concentrations of aerosols and criteria gases in the diesel exhaust, both upstream and downstream of the DPF system. The concentrations and size distributions of aerosols were measured using a fast mobility particle sizer spectrometer, in exhaust diluted by a partial flow dilution system. The concentrations of CO2, CO, NO, and NO2 were measured in the raw exhaust using a Fourier transform infra-red spectrometer. Both field and laboratory emissions tests showed that the evaluated DPF systems were very effective in reducing aerosol emissions from all tested engines, and for all test conditions. The systems were found to have minor effects on gaseous emissions from those engines. The findings from this study should help the mining industry to better understand the benefits and challenges of using DPF systems to control the exposure of underground miners to diesel aerosols.

Aug 1, 2013

By Russell J. Denny

"A 25m deep cut-off wall is required for environmental remediation of a Former Chlor-Alkali Plant. Extensive trials were conducted to verify the effectiveness of the mixes proposed, with the requirements of the cut-off wall to include limiting criteria for hydraulic permeability, vapour permeability and strength, over a 100 year design life. A limited number of field CSM trial panels were installed on a nearby site with similar stratigraphy, and a variety of mixes and mixing methodologies were used, together with the extraction of deep wet grabbed samples from the panels, which were tested for strength, hydraulic permeability and gas permeability. Test results obtained from these trials revealed a trend which allowed the construction methodology to be decided. Further to this, the mix design needed to be resolved, together with sensitivity analysis on the variations in the mix which might occur during construction, as a result of normal unavoidable variations in construction technique. Laboratory sampling would be used at lesser expense, to resolve the final mix design and analyse the sensitivity of the possible mix variations. An initial series of laboratory mixed samples were prepared using soil samples and groundwater obtained from the site, and testing carried out. However the test results in this initial series of laboratory tests could not match the results which had been achieved in the field trials. Closer scrutiny and investigation and rounds of sampling and testing, then revealed laboratory techniques for mixing and sampling which provided a logical way to match the actual field test results. CSM Construction is due to commence soon and will provide more extensive results which can be compared back to the laboratory trials. This project provides a valuable opportunity to resolve methods of laboratory sampling so that they compare well with results from in-situ deep mixing.INTRODUCTIONThe former chlor-alkali plant at Botany, NSW, which operated from 1945 until 2002, used mercury cell technology and brine solution to manufacture chlorine, caustic soda, hydrochloric acid, sodium hypochlorite and ferric chloride. Mercury contamination is present in the permeable alluvial soil profile beneath the site. The mercury is present in the form of elemental and inorganic mercury, together with dissolved methyl mercury in the groundwater and soil profile beneath the site and also down-gradient of the site, to depths of up to 25m. Residual clay and sandstone bedrock at approximately 25m depth are relatively impermeable and limit the contamination plume. A cap and contain approach has been recommended by consultants Golder Associates, and this involved a subsurface containment wall, or cutoff wall, to restrict groundwater ingress and egress, and lateral subsurface vapour migration. The cut-off wall is situated on the perimeter of the site, with a total length of 430m and passing through alluvial Botany Sands, with a nominal key into the underlying residual clay or sand stone at 20 to 25m depth. An HDPE liner insert was proposed for the upper 7m of wall above the water table, to further limit gas permeability."

Jan 1, 2015

By S. W. Jacobsz, Y. Narainsamy

Several high-impact tailings dam failures around the world in recent years have placed a renewed focus on the stability of tailings dams and pointed to potential shortcomings in traditional drained design and safety evaluation procedures. A need to consider undrained shear strength in the design of tailings facilities has become apparent. However, there are specific requirements that need to be met before undrained shearing occurs. In South Africa, the last major failure was likely the Merriespruit disaster in 1994, which leads to the question of whether the conditions required for undrained shearing are readily applicable to South African tailings dams. This paper describes research at the University of Pretoria that has recently commenced to further investigate the conditions required for undrained failure to occur. The research includes laboratory and field testing to replicate these conditions in the laboratory and relate them to those found in an active tailings dam.

Jun 2, 2022

By Ashok Kumar, Rajendra Singh, Arun Kr. Singh

"A simple analysis of site conditions and capability of the mechanised depillaring (MD) operation found that this approach is suitable to address the strata control issues in coal pillar extraction under the weak and laminated roof strata of Pinoura mine. A continuous miner (CM) with a ram car and quad-bolter are used for single pass pillar extraction (first time in the country) to achieve a relatively faster rate of depillaring. A total of eleven panels are depillared under weak and laminated roof strata with a fair-rated rock mass rating (CMRI-RMR). It is observed that there is less influence of roof caving over the surrounding mining structures, especially those located out-bye the side of the extraction line. An attempt is made to quantify the goaf influence by field studies, which show that the maximum value of mining-induced vertical stress is 2.83 MPa, and the range of influence remains limited to around 15 m from the line of extraction. However, the problem of roof instability under the influenced zone was experienced due to the inherent nature of the weak roof strata. The chances of trapping of CM under weak and laminated roof strata of the panels is reduced by deriving a threshold value of the roof dilation, on the basis of a simple statistical analysis of the obtained field results. However, few incidences of roof collapses are observed over the CM due to the unpredictable behaviour of the geological structures below the freshly exposed strata, which also caused an obstruction in the speed of the extraction. This paper presents results of the field and laboratory studies, conducted for a successful application of the single-pass pillar extraction method, along with details of some CM trapping cases below the weak and laminated roof strata.INTRODUCTIONCoal is the major natural resource to meet the growing energy demand of India and this trend is likely to continue for the next 20 years in the country. A major part of the Indian coal belongs to Gondwana period, and only a small part belongs to Tertiary period. The estimated coal reserve in India per the exploration work done up to a maximum depth of 1200 m is 315.149 billion tonnes, including the proven coal reserve of 143.058 billion tonnes (CMPDIL, 2017). Even in presence of these huge resources of coal in India, there is a considerable gap between production and the users’ demand of coal. Most of the mines are operated by conventional semi-mechanised Bord and Pillar (B&P) methods; thus, the mining industry has gained a considerable amount of operational experience (Singh, Singh, and Dhar, 1996) and knowledge about strata behaviour (Singh and Singh, 1999; Singh et al., 2008) using this method. However, recently, the Indian coal mining industry has introduced some mechanised depillaring (MD) operations, where the level of production is relatively high. This approach of depillaring improves safety along with the production and productivity of a depillaring operation (Ram et al., 2017). The nature of the overlying strata of these depillaring operations vary greatly: from highly laminated, weak, and easily caveable to massive, strong, and difficult to cave."

Jan 1, 2018

By Scott Turner

OUR Institute, in its annual Directory, states the following: The purpose of each Technical Committee is to further the development of the special mineral industries in its field, chiefly through obtaining and discussing papers suitable for publication by the Institute. The proper field of the new Health and Safety in Mines Committee is judged to include the entire mining industry, and involves the multitude of health and safety problems arising in all kinds of mining operations. The mining industry in the United States has made much progress during recent years in reducing accidents. This advance has been widespread, and has been especially notable in the mining of iron ore. Yet the statistics of the U. S. Bureau of Mines, when compared with figures of the National Safety Council for other industries, show that mining still has a higher personal mishap rate than any other major industry in this country. In addition, studies of dollars-and-cents cost of casualty occurrences indicate that an important part of our mining cost, held by various authorities to be as much as 10 per cent of the total, is due to accidents.

Jan 1, 1933

By D J. Williams, G W. Wilson, S, A B. Tran

A comprehensive field program was implemented to evaluate the internal structure and hydrology of two full-scale waste rock piles. The excavation of waste rock dumps for in-pit disposal at the two mine sites provided an opportunity to characterise the in situ properties of the dumps given contrasting geologic and climatic settings. The internal structure and materials within the dumps were observed and sampled as the waste rock piles were being excavated and placed in the open pits for permanent closure. The field program was designed to fully characterise the structure and material properties of the waste rock. The alteration of the material by physical and chemical weathering was also observed. Samples were analysed for paste pH, water content, grain size distribution and geochemistry. In situ density and matric suction were also measured. Soil water characteristic curves and saturated hydraulic conductivity were measured for representative materials. These properties were used to predict seepage pathways through the waste rock and the resulting outflow geochemistry using the finite element model SEEP/W. The materials in the dump at Site 1 were predominantly fine-grained in texture and highly weathered. The presence of dipping beds with alternating coarse and fine materials was evident throughout the profile of the dump. The structure of the waste rock appears to have an impact on the hydrologic pathways within the waste rock pile. The material in the dump at Site 2 was found to be competent and resistant to particle size breakdown. The particles range in size from clay size to large boulders with the median particle size being approximately 125 mm in diameter. The coarse-grained texture of the waste rock resulted in a loosely packed arrangement of coarse particles with little matrix material infilling the pore spaces between the coarse-grained particles. Seepage modelling for Site 1 was completed to predict seepage paths based on observed structure and hydraulic properties measured in the laboratory. The modelling showed that materials with a fine grain size distribution become the dominant pathways for flow through the waste rock pile. The modelling also showed that layers with high silt and sand contents are subject to the highest flow rates. Finer grained clay rich layers have a low hydraulic conductivity and do not convey large volumes of water. Alternately, coarse gravel and cobble materials are unsaturated under values of matric suction that approach the residual water content of the material and do not transmit liquid water. The seepage modelling together with the results of the geochemical analysis show that the dominant particle size that receives the most fluid flow and flushing ranges from fine sand to silt, corresponding to materials with air entry values ranging between 5 kPa to 50 kPa.

Jan 1, 2003

By D. Blackwell, W. R. Reed, G. Ross, S. Peters, M. Shahan

Dust collectors for roof bolting machines generally use a dry box to collect the roof bolting material. Recently, an underground mining operation converted a dry box dust collector to a wet box dust collector with a unique exception from MSHA for testing purposes.Water is routed to the roof bolter fromthe main water line of the continuous miner. The wet box utilizes a water spray to wet the incoming material. Testing was conducted comparing the two different collector types. Respirable dust concentrations surrounding the roof bolter with the different collection boxes were similar. The main difference in respirable dust concentrations occurred when cleaning the dust boxes. The average respirable dust concentration during cleaning of the wet box was 0.475 mg/ m3, and during the cleaning of the dry box, the average respirable dust concentration was 1.188 mg/m3, a 60% reduction in respirable dust concentration. The quartz content of the roofmaterialwas high, ranging from 28.9 to 52.7%during this study. The results from this study indicate that using the wet box as a collector reduced exposure to respirable dust up to 60% when cleaning the collector boxes.

Aug 26, 2020

By D. Blackwell, W. R. Reed, G. Ross, S. Peters, M. Shahan

Dust collectors for roof bolting machines generally use a dry box to collect the roof bolting material. Recently, an underground mining operation converted a dry box dust collector to a wet box dust collector with a unique exception from MSHA for testing purposes. Water is routed to the roof bolter from the main water line of the continuous miner. The wet box utilizes a water spray to wet the incoming material. Testing was conducted comparing the two different collector types. Respirable dust concentrations surrounding the roof bolter with the different collection boxes were similar. The main difference in respirable dust concentrations occurred when cleaning the dust boxes. The average respirable dust concentration during cleaning of the wet box was 0.475 mg/m3, and during the cleaning of the dry box the average respirable dust concentration was 1.188 mg/m3. The silica content of the roof material was high, ranging from 28.9% to 52.7% during this study. The results from this study indicate that using the wet box as a collector reduced exposure to respirable dust up to 60%when cleaning the collector boxes. INTRODUCTION Currently, the dry vacuum dust collection system is the standard dust collector on roof bolters in underground coal mining. It has been proven to be an effective dust control to prevent roof bolter operators’ overexposure to coal mine respirable silica dust during roof bolting operations [Potts eta l, 2011 and Colinet, 2013]. The dry collection system works as follows: drill cuttings are vacuumed into the precleaner. The precleaner dumps oversized material onto the mine floor while undersized material enters the dust box via vacuum airflow produced by a blower. The cuttings entering the dust box are either deposited on the floor of the dust box or into a dust collector bag. The vacuum airflow leaves the dust box through a final filter which removes any small particles from the airflow. Figure 1 shows the internal view of two dry collection system boxes; one that does not use the dust collector bags and another that uses the dust collector bags. Dust collectors that use dust collector bags to contain material inside the dust collector box have been shown to provide better protection to roof bolter operators than dust collectors that do not use the bags [Listak and Beck 2008]. The dry collectors are very efficient at reducing respirable coal mine dust exposure from roof bolting activities. Recently, Blue Mountain Energy’s Deserado underground coal mining operation, outside Rangely, CO, made a modification to the dry collector system to convert it to a wet collector system with a unique exception from the Mine Safety and Health Administration (MSHA) for testing purposes. The wet collector system still uses a vacuum system to pull material from the vertical roof bolt hole, but incorporates a water spray nozzle located inside the dust box to wet the incoming material. The flow through the nozzle ranges from 1.9–7.6 lpm (0.5–2.0 gpm) at 0.69 MPa (100 psi). The conversion to the wet collector system removes the precleaner and the cyclones inside the dust box. The wet material (sludge) then empties through a specialized valve in the bottom of the box. The final filter is still used to prevent respirable dust from leaving the dust box through the exhaust. During operation, the wet collector dust box is opened and hosed clean after roof bolting every place. After every two entries the final filter is changed out. Figure 2 shows the inside of the wet collector box.

Jan 1, 2019

By Y A. Stepanyants, J Crawford

A practical field method for determining the maximum value of the intrinsic oxidation rate, Smax , of sulfidic materials in waste rock dumps is proposed. Knowledge of the intrinsic oxidation rate of sulfidic materials distributed in a dump is necessary for predictive modelling of oxidation and pollutant generation over time. The suggested method uses the fact that drilling waste rock dumps to install probes for monitoring temperature and oxygen concentration causes large volumes of air to be injected into a dump by the drill rig. By measuring the rate of decrease of oxygen concentration along the length of a borehole immediately after installation, it is proposed that Smax can be calculated at different depths. The aims of this work were: to derive a simple, practical formula for the estimation of Smax from the oxygen concentrations measured over time, based on some simplifying assumptions; to use a two-dimensional numerical model that incorporates all the necessary physical processes to model the behaviour of an aerated dump over time for a reasonable range of dump and material parameters; and to compare the results of the two approaches to assess the validity of the simple formula as a method for estimating Smax. It has been found that the technique can provide reliable estimates of Smax when the value is of the order of 10-7 kg(O2) m-3 s-1 or greater. At the lower end of the range however the radius of the zone aerated during drilling becomes an important parameter and further work has been recommended to investigate this aspect of the method.

Jan 1, 2003

By J. D. Noll

The Mine Safety and Health Administration (MSHA) has promulgated rules to limit the exposure of metal/nonmetal underground miners to diesel particulate matter (DPM). These rules have resulted in many types of control tech­nologies being implemented including diesel particulate filters (DPF). The passive type DPF is the most desirable because it requires little maintenance and it regenerates while the vehicle is operating. One problem with passive DPFs is that many vehicles cannot develop the sustained exhaust temperatures needed to initiate DPF regeneration, and thus it is required that the DPF be catalyzed to decrease the temperature needed for regeneration. In some past studies, such catalyzed filters have been shown to cause an increase in the nitrogen dioxide concentrations in the exhaust, resulting in a potential health hazard. In this study, a lightly catalyzed DPF along with a fuel-born catalyst were employed to help reduce the DPM emissions from a 980F loader used for cleanup in a stone mine. After 30 days of use, the filter continued to regenerate successfully at the exhaust temperatures generated by this loader, substantially reduced DPM concentrations emitted in the exhaust, and did not cause a measurable increase in nitrogen dioxide levels that could be attributed to the device.

Jan 1, 2009

By J. R. Patts, L. D. Patts, S. J. Janisko, T. Barone

"Controlling float coal dust in underground coal mines before dispersal into the general airstream can reduce the risk of mine explosions while potentially achieving a more efficient and effective use of rock dust. A prototype, flooded-bed scrubber was evaluated for float coal dust control in the return of a continuous miner section. The scrubber was installed in line between the ventilation tubing and an exhausting auxiliary fan. Airborne and deposited dust mass measurements were collected over a period of three days at set distances from the fan exhaust to assess the changes in float coal dust levels in the return due to the operation of the scrubber. Mass-based measurements were collected on a per-cut basis and were normalized per foot of advance by the continuous miner. Results show that average float coal dust levels measured under baseline conditions were reduced by over 91% when operating the scrubber. INTRODUCTION In 2012, underground mining in the United States produced over 342 million tons of coal [EIA 2013]. During the cutting, crushing, and transport of this coal, dust is generated and can be entrained in the air ventilating the mine. Title 30 Code of Federal Regulations Part 75.400-1 (30 CFR§ 75.400-1) defines float coal dust as particles of coal that can pass a No. 200 sieve. These coal particles can be carried by the ventilating air into return entries before settling onto mine surfaces [NIOSH 2006]. If this float coal dust becomes re-entrained into the airstream, it can propagate an explosion throughout mine workings [Harris et al. 2010]. Application of rock dust in underground coal mines is required by Federal regulation as a means of preventing the propagation of explosions by float coal dust. In order to meet Title 30 Code of Federal Regulations Part 75.403 (30 CFR § 75.403), 80% incombustible content must be maintained in the composition of dust deposited in mine entries [76 Fed. Reg. 35968 (2011)]. This fraction of incombustible content is increased if elevated levels of methane are present. In order to maintain the required incombustible content, frequent or constant application of rock dust is undertaken by mine operators. Title 30 Code of Federal Regulations Part 75.2 (30 CFR § 75.2) defines the properties of the rock dust that must be used by mine operators."

Jan 1, 2015

By M. L. Harris

In underground mines, coal dust explosions are prevented by the addition of rock dust sufficient to render the coal dust inert. The National Institute for Occupational Safety and Health (NIOSH) developed a hand-held instrument that uses optical reflectance to measure the explosibility of a rock dust and coal dust mixture. This instrument is called the Coal Dust Explosibility Meter (CDEM). In this study, NIOSH personnel accompanied Mine Safety and Health Administration (MSHA) inspectors on their routine band surveys in five underground coal mines in MSHA District 2 (Pennsylvania) and three underground coal mines in MSHA District 11 (Alabama). While underground, NIOSH personnel and MSHA inspectors used the CDEM to assess the explosibilities of the dust samples. The values of percent incombustible content (percent IC) determined by the CDEM agreed well with those obtained later by low-temperature ashing (LTA) in both MSHA and NIOSH laboratories. Further, the meter identified some samples as potentially explosible that LTA analysis had found to possess sufficient rock dust for inerting. The CDEM provides more information on the hazards in the mine. Rapid identification of areas with explosible dust mixtures using the CDEM allows for immediate intervention rather than a wait of several weeks for laboratory analysis.

Jan 1, 2008

By Michael Magerstädt

Material loss by abrasion of contact surfaces of pipes, chutes, pumps, and other equipment in contact with ore is one of the main reasons for downtime of mining operations. Abrasion protection materials in use range from expensive tungsten carbide overlay to hardened steels, ceramics, as well as polymers, particularly polyurethanes (PUR). This paper describes abrasion protection products made from High Performance Polyurethane Elastomers. An interior pipe coating was developed that exhibited outstanding abrasion resistance and an extremely high adhesion to steel. Years of field testing in oil sands tailings as well as applications in slurry lines (e.g., phosphate slurries) have proven the performance of this material. A proprietary field joining process was developed and successfully applied in the field. This joining process requires only one field weld per joint very similar to the joining of uncoated pipe. No internal re-coating is necessary adding savings during pipe laying to the significant savings of reduced down time. Using the building-kit chemistry of polyurethane synthesis, similar high performance elastomers were used to extend the life time of ball mills. An intelligent system was developed in which wear parts contain sensors reporting the actual wear thereby optimizing maintenance interval leading to significant cost savings for the operator. Test data as well as field experience with High Performance PUR Elastomers for abrasion protection in mining are presented.

Aug 1, 2013

By J. P. Kennedy

Process data managers or historians are recognized as essential for reengineering projects in industrial plants. With increasing automatic data collection, the knowledge of how to use these data profitably grows as well. This paper is a summary of the data historian and its components plus examples of benefits including environmental reporting, performance monitoring, and exception reporting to management.

Jan 1, 1994

By Y. Guglielmi, C. Gout, P. Henry, P. Dick

The key questions about fault reactivation in shales concern the potential enhanced fluid displacement through a previously low-permeability aseismic shale formation. Here we selected a critically-stressed fault cross-cutting the underground research facility of Tournemire (France) which is located in Toarcian shales. Several inclined boreholes were drilled across the 8.5 m thick fault zone characterized by a fractured damage zone (FDZ) and a central 2.4 m thick complex core (FC) made of multiple shear bands with gouge intercalated with highly fractured lenses. The fault was pressurized using a straddle packer system defining a 2.4m long injection chamber normal to the fault surface. Three fault zone intervals were tested, two in the fault damage zone and one in the fault core. A three-dimensional displacement sensor set in the chamber allowed continuous synchronous coupled monitoring of fault movements, injection pressure and flow rate. An anticlockwise 0.22-to-0.05 mm fault slip was captured associated with a 10-to-100 hydraulic aperture increase of the fault. Preliminary analyses of the experiments show that leakage in the fault zone is controlled by strength and stress magnitude contrasts between the fault core and the fault damage zone. Fault damage zone discontinuities display a much higher peak static friction angle than the fault core shear zones, respectively of 34 and 22° that could be related to complex interactions between healing and sealing processes. Fault core leakage is much more dependent on strain than on effective stress variations. Discontinuous, pulse-like leakage, develops following complex failure processes that may simultaneously take place in the gouge zones and along the large pre-existing discontinuities. Such results may be of importance in evaluating fault seal integrity in oil and gas exploration, production or CO2 storage or underground excavations monitoring.

Jan 1, 2015

By Louise Corriveau

Exploration strategies have traditionally considered felsic gneiss complexes of the Canadian Shield sterile. This paradigm is challenged with the discovery of extensive granulite-facies Cu-Au, Fe oxides-bearing hydrothermal systems in the 1.4 Ga Bondy and 1.5 Ga La Romaine volcano-plutonic complexes of the Grenville Province. Early identification of magnetite-rich units in association with meta-exhalite and pelite-like units was key to targeting the search for mineralization, protolith information and indicators of pre-metamorphic hydrothermal activity during regional surveys of these frontier terrains. Textural evidences for a volcano-plutonic setting were found. There remained, however, numerous impediments to the recognition that the ubiquitous magnetite-laden units and associated aluminous gneiss were hydrothermal in origin. Many metamorphic reactions form magnetite at the amphibolite to granulite facies transition, and hydrothermally-leached rocks resemble metapelite or migmatitic restite, while carbonate alteration zones may look like marble or calc-silicate rock. Non-typical metamorphic mineral assemblages, modes and colours arise when hydrothermally-derived rock types are metamorphosed. These effective markers served as tools for reliable field identification of hydrothermally-altered rocks. In our case-studies, we traced pre-metamorphic hydrothermally-driven Fe-oxide precipitation in association with sericitization, albitization, pyrophyllite alteration, chloritization, and B enrichment by mapping unusually high contents of (1) magnetite or hematite, (2) biotite, (3) albite, (4) sillimanite, (5) orthopyroxene or phlogopite with cordierite, and (6) tourmaline or kornerupine. The unveiled garnetite, tourmalinite, and aluminous gneiss had assemblages that vary according to metamorphic grade and composition. To assess if high mode of Fe-Mg-Al phases resulted from partial melting (restitic residue) or metamorphism of hydrothermal rocks, we compared leucosome mineral assemblages, shape and amount with that expected of in situ partial melting reactions. In both areas there is no compelling evidence for these units to be restites. In contrast, the presence of lapilli in garnet-cordierite-sillimanite gneiss, though extremely rare, constitutes conclusive evidence for extreme pre-metamorphic high-sulphidation alteration of a volcanic protolith, while Fe-oxides or sillimanite-bearing nodules and veins record a less pervasive alteration. Geochemical research on element mobility and mass balance calculations further testified of an hydrothermal origin for these gneisses. The magnetite-rich units, together with calc-silicate rocks, garnetite, hornblendite, albitite among amphibolite, provided effective guides to sites of fluid discharge and led to the discovery of Cu and Cu-Au showings. With the presence of highsulphidation alteration, these features suggest early Cu-Au VHMS-type alteration halos within a predominantly felsic composite volcano-plutonic arc setting for both case-studies. Evidences for subsequent F-driven orthomagmatic fluid activity are also present.

May 1, 2003

By Todd Minoski, Matthew McElhinney, Mark Morris, Mark Mazzella, Joseph Bright, Morgan Sears, Craig Compton

To promote the safety and health of U.S. mineworkers, researchers with the National Institute for Occupational Safety and Health (NIOSH) are currently involved in gathering additional field data from the nation’s underground coal mines. The purpose of this field study was to monitor ground movement and changes in pressure during mining where conditions include a thick parting in the coal seam. To accomplish this, three arrays of field instrumentation were installed in the wraparound bleeder of a room-and-pillar panel at the Maple Eagle mine located in southern West Virginia. Borehole pressure cells (BPCs) were used to monitor the change in pressure in pillars located adjacent to the gob. Roof extensometers were installed to measure roof sag at various horizons in the immediate roof, while rib extensometers were installed to measure displacement of the in-seam parting as mining progressed. Additionally, visual observations and manual measurements were taken during subsequent site visits. The repeatability of results, important from a scientific perspective, was accomplished by successfully obtaining field measurements from two nearly identical instrumentation sites. The data collected indicated that the front abutment extent at the edge of the panel was approximately 200 ft, corresponding to a distance of 9– 10 times the square root of the depth. Yielding of the slabbed pillar began when the pillar line was approximately 290 ft outby the instrumentation sites. This was followed by load shedding onto the abutments and the measurement of small amounts of roof sag in the No. 1 entry. Instrumentation data, as presented in this paper, can be used to better understand stress redistribution, pillar performance, and roof/rib displacements. Additionally, this data is suitable for assisting in the calibration of numerical models. Insight gained from applying these models can be used to make better engineering-based judgments for conditions that could potentially be encountered in the future.

Jul 1, 2023

By M. Yekich, W. R. Reed, G. Ross, M. Shahan

"Canopy air curtains on roof bolting machines have been proven to protect miners from respirable dust, preventing their overexposure to dust. Another desired application for canopy air curtains is in the compartments of shuttle cars. The challenges faced in developing the design of canopy air curtains for shuttle cars include mine ventilation rates in tandem with the shuttle car tram speeds. The resulting cab airspeeds may exceed 182 m/min (600 fpm), as found in the present study conducted in a central Appalachian underground coal mine by U.S. National Institute for Occupational Safety and Health (NIOSH) researchers. Prior research and laboratory testing had indicated that successfully protecting a miner in high air velocities is difficult, because the clean air from the canopy air curtain is unable to penetrate through the high-velocity mine air. In this study, the dust concentrations to which a shuttle car operator was exposed were measured, and air velocities experienced by the operator were measured as well using a recording vane anemometer. The results indicate that the highest exposure to respirable dust, 2.22 mg/m3, occurred when the shuttle car was loading at the continuous miner, where the average airspeed was 48 m/min (157 fpm). While tramming, the operator was exposed to 0.77 mg/m3 of respirable dust with an average airspeed of 62 m/min (203 fpm). This study indicates that a canopy air curtain system can be designed to greatly reduce an operator’s exposure to respirable dust by providing clean air to the operator, as the majority of the operator’s dust exposure occurs in air velocities slower than 61 m/min (200 fpm). IntroductionThe U.S. National Institute for Occupational Safety and Health (NIOSH) issued contract #200-2015-63485 to develop a canopy air curtain for coal mine shuttle cars with Marshall University and J.H. Fletcher & Co. (Salem, Begley and Ross, 2016). The proposed design maintains a design similar to that of a roof bolter canopy air curtain by providing filtered air through a blower over the operator. The plenum, which will provide uniform airflow over the operator, is anticipated to be built into the shuttle car canopy. One of the main interferences with a canopy air curtain is ventilation airflow perpendicular to the plenum airflow (Engel, Johnson and Raether, 1987). This ventilation airflow can shear the downward flow from the plenum, and this shear can reduce the effectiveness of the canopy air curtain by either disrupting the downward flow or allowing contaminated mine air into the canopy air curtain zone of protection."

Jan 11, 2018