Search Documents

Gaby Copper Mining?s Gabriela Mistral property is located in the Antofagasta region of northern Chile, at an altitude of 2,660 m (8,727 ft) above sea level. The reserve contains an estimated 562 Mt (620 million st) of oxide ore with an average grade of 0.41 percent total copper. The mine went into production in 2008. Gaby Copper faced the problem of having no reliable way to measure the solids level. This is a challenge that exists throughout the mining industry, where dust in the air and accumulation of solids on a sensor make accurate measurements difficult in areas such as transfer chutes, the rock box underneath crushers, silos and anywhere else that information is needed on the level of solids. The next-generation technology in the Sitrans LR560 radar from Siemens addresses this challenge. With a frequency of 78 GHz ? higher than previous generations of radar ? it provides a more robust signal for measuring in areas where there are high levels of dust accumulation. The Sitrans LR560 provides a signal beam angle of four degrees, significantly narrower than any other product on the market can offer.

Jan 1, 2014

THIS article describes the origin and details of a hydraulically operated switch to control the operation of an automatic underground pumping system. This system was installed in December, 1939, on the 2,350-foot level at No. 5 shaft of the Buffalo Ankerite mine. The pumping unit consists of an 8-stage centrifugal pump direct-connected to a 150 h .p., 2,200 volt motor. Pumping capacity is 200 gallons per minute under a 1,315-foot head and with a flooded suction. The control consists of a 200 amp., 2,200 volt oil-immersed starter with thermal overload protection, thermal protection on the pump, and a flow switch that is bypassed for 30 seconds after the pump starts. The 30-second time lag is operated by a relay mounted on the panel. There is a swing check valve in the discharge line of the pump which originally operated the flow switch by means of a connected outside lever which closed the switch as the check valve opened.

Jan 1, 1945

By A. Mcdonald, F. W. Breaks, T. F. Morris, S. A. Averill, D. C. Crabtree

Abstract-Gahnite, a zinc-bearing spinel, is a resistate mineral that may be used as an indicator mineral of polymetallic deposits in high-grade metamorphic terrain. The Ontario Geological Survey recently completed surficial mapping and sampling programs in the Separation Lake area of northwestern Ontario and Kinniwabi Lake area of northeastern Ontario in which gahnite was recovered from samples of surficial sediments. Ternary plots of the composition (ZnO, MgO, FeO[t]) of gahnite recovered from these surficial studies reveal three distinct groups: Group 1 is characterized by low (< 1 wt%) MgO values; Group 2 by higher (>1 wt%) MgO values; and Group 3 by higher FeO(t) values than Groups 1 and 2. The composition of in situ gahnite recovered from volcanogenic massive sulfide mineralization, Zn-rich Sedex-type mineralization and peraluminous rare-element mineralized granite and pegmatite also was determined. The composition of the gahnite obtained from surficial samples was compared with that of in situ material. Gahnite from the peraluminous rareelement granite and pegmatite overlapped very well with surficial gahnite of Group 1. Gahnite from volcanogenic massive sulfide mineralization and Sedex-type mineralization overlapped well with surficial gahnite of Group 2. These results suggest that determination of gahnite composition in indicator mineral surveys may be useful in exploration programs when assessing the mineral potential of a region.

Jan 1, 1997

By A. Mcdonald, F. W. Breaks, T. F. Morris, S. A. Averill, D. C. Crabtree

Gahnite, a zinc-bearing spinel, is a resistate mineral that may be used as an indicator mineral of polymetallic deposits in high-grade metamorphic terrain. The Ontario Geological Survey recently completed sur?cial mapping and sampling programs in the Separation Lake area of north-western Ontario and Kinniwabi Lake area of northeastern Ontario in which gahnite was recovered from samples of sur?cial sediments. Ternary plots of the composition (ZnO, MgO, FeO[t]) of gahnite recovered from these sur?cial studies reveal three distinct groups: Group 1 is characterized by low (< 1 wt%) MgO values; Group 2 by higher (>1 wt%) MgO values; and Group 3 by higher FeO(t)values than Groups 1 and 2. The composition of in situ gahnite recovered from volcanogenic massive sul?de mineralization, Zn-rich Sedex-type mineralization and peraluminous rare-element mineralized granite and pegmatite also was determined. The composition of the gahnite obtained from sur?cial samples was compared with that of in situ material. Gahnite from the peraluminous rare-element granite and pegmatite overlapped very well with sur?cial gahnite of Group 1. Gahnite from volcanogenic massive sul?de mineralization and Sedex-type mineralization overlapped well with sur?cial gahnite of Group 2. These results suggest that determination of gahnite composition in indi-cator mineral surveys may be useful in exploration programs when assessing the mineral potential of a region.

Jan 1, 1997

By S. Espley, T. Nyabeze, D. Beneteau

"Many mentorship programs are available to Canadian mining industry employees. Some are company-led initiatives, whereas others are provided through educational institutions or nonprofit organizations. In 2016, a national survey was launched to gain insight into perceptions of what mentorship is, learn about available programs, and collate experiences with formal and informal mentorship opportunities. This paper outlines survey findings and delivers recommendations to industry for consideration in employee mentorship programs. In addition, mining industry leaders share their mentor/mentee perspectives. The intent of this paper is to bring awareness of best practices that can help employees grow and develop in their profession.RÉSUMÉ Les employés de l’industrie minière canadienne ont accès à de nombreux programmes d’encadrement. Certains sont des initiatives menées par les sociétés, d’autres sont proposées par le biais d’établissements d’enseignement ou d’organismes à but non lucratif. En 2016, une enquête à l’échelle nationale a été lancée en vue d’obtenir des informations quant à la perception de ce qu’est réellement l’encadrement, de découvrir les programmes proposés et de comparer les expériences aux possibilités d’encadrement, officielles ou non. Cet article présente les résultats de cette enquête et fournit des recommandations à l’intention de l’industrie afin qu’elle les prenne en compte dans ses programmes d’encadrement des employés. En outre, des chefs de file de l’industrie minière partagent leurs points de vue conseillers/protégés. L’intention de cet article est de sensibiliser les employés aux meilleures pratiques, ce qui les aidera à évoluer et à se développer dans leur profession. INTRODUCTIONThis paper about mentorship in the mining industry is based on voluntary responses to a cold survey, written and circulated by the authors. In 2016, a link to an online mentorship survey was circulated to males and females in the mining industry with the belief that mentorship programs should be available to everyone. The link was delivered via the authors’ personal networks in mining, the CIM Reporter, Women in Mining (WIM) email blasts, LinkedIn, and Facebook. This paper summarizes the answers to the survey questions. The paper is a follow up to one by the same authors (Nyabeze, Espley, & Beneteau, 2010), which was written to gain insight into why women join and stay in the mining industry, and to learn why the overall representation of women is low."

Jan 1, 2018

By Jeanie Wills, Theresa Nyabeze, Samantha Espley, Donna Beneteau

This presentation reports survey findings that aim to modernize the definition and understanding of the term 'mining.' The survey, conducted via LinkedIn in Winter 2024, garnered responses from a diverse group of individuals, including current or former employees of mining or exploration companies, mining consulting firms, service providers, supplier firms, as well as students and retirees with industry experience. The data, ethically approved by the University of Saskatchewan, offers valuable insights into satisfaction levels within the mining sector and suggests an expansion of the identifying characteristics of definitions of mining. This marks the third CIM gaining insights paper by Beneteau, Espley, and Nyabeze, following previous works on 'Career Satisfaction for Women in Mining' (2010) and 'Mentorship Initiatives in the Canadian Mining Industry' (2018*)."

Oct 1, 2024

By S. Norman Kesten

The Galena mine is located astride the Polaris fault in the Coeur d&apos;Alene district of northern Idaho. The surface installations are about a mile up Lake Gulch, the mouth of which is about 2.4 km (1 112 miles) west of the old town of Wallace. The mine had its beginnings when the first claims were located in the early boom days of the district in the 1880s and when the first underground ore bodies were opened up in 1917. During the ensuing 14 years, ore was mined from which were recovered 5.4 Mkg (12 million lb) of lead and almost 14.2 Mg (112 million oz) of silver. Workings consisted principally of a vertical shaft from surface to the 800 level and an offset underground shaft to the 1600 level, together with extensive lateral openings. High-grade silver-copper ore was discovered near the Silver Standard fault in the Sunshine mine, a few miles to the west, on the 1700 level in 1930. By 1937, the Sunshine and adjacent mines were producing silver-copper ore on a regular basis. In 1943 additional ore of a similar type was found along the Chester fault, to the east of the principal Sunshine workings. The interest of American Smelting and Refining Co. (renamed ASARCO in 1975) was aroused and the company&apos;s geologists determined that the Galena mine, idle since 1931, provided a geological environment in which similar ore might be found. After negotiations were initiated with the owners of the property, Callahan Zinc-Lead Co., the property in question was deeded to Callahan&apos;s wholly owned subsidiary, Vulcan Silver-Lead.

Jan 1, 1990

By J. W. Breen

ASARCO Incorporated has upgraded or is in the process of upgrading the Galena mine electrical, pumping, refrigeration, compressed air, ventilation, hoisting and rockburst monitoring systems to allow continued mining and development work on the 1 589-m (5,200-ft.) level and to provide services for projected deeper mining and development. Additionally, a separate lead-silver milling circuit has been added to the silver-copper mill to process lead-silver ore reserves. This paper describes completed and planned improvements made to date on these systems.

Jan 1, 1991

By John L. Hostetler

GALFAN, the Zn-5% Al-mischmetal hot-dip galvanizing alloy is coated onto steel sheet, wire, and tube using high-speed continuous galvanizing lines. Factors critical to producing high quality GALFAN are reviewed, The relationship between minimum mischmetal content in the GALFAN alloy and furnace dewpoint will be described. The relationship between peak annealing temperature and furnace dewpoint will also be shown. Typical suategies for operating multi-purpose hot-dip galvanizing lines including GALFAN will be described. A recent development has allowed preparation of steel smp for GALFAN coating using aqueous fluxes rather than high temperature annealing. This allows production of GALFAN-coated smp without over-ageing of the steel, and allows high steel strengths and hardnesses to be obtained. The principles of this process will be described.

Jan 1, 1992

By Richard F. Lynch, Frank E. Goodwin

"The development of Galfan, a new generation 95% zinc-5% aluminum-mischmetal alloy coating for steel, offers opportunities for greater fabrication flexibility and upgraded corrosion performance in automotive applications. The formability of Galfan is equivalent to that of electrogalvanized steel, based on laboratory tests and automotive component fabrication. Corrosion resistance of Galfan exceeds that of hot dip and electrogalvanized, including performance in automotive industry tests. Automotive production applications for deep drawn and stamped components in France and Germany are based on the ability to meet dual performance requirements for upgraded formability and corrosion resistance. The first U.S. Galfan application was on 1985 model Ford cars and light trucks for transmission oil cooler lines which has now expanded into a number of power steering tubing uses. IntroductionContinuing requirements for improved vehicle performance coupled with the ever present need for reduced cost have spawned the development of a number of new coated steel products. Among this new generation of coated steels is Gaifan™, a 95070 zinc-Solo aluminum-mischmetal hot dip alloy coating. Galfan exhibits particular promise for automotive use based on broad fabrication advantages and upgraded product performance(I ),The unique characteristic of Galfan is the key combination of greatly improved formability with much longer corrosion life. Galfan provides significantly better formability than any other hot dip coating. Testing shows that formability is limited primarily by the steel substrate to which the Galfan coating is applied. Galfan exhibits excellent resistance to flaking and microcracking during commercial forming operations. The result is the elimination of unnoticed damage to the coating which would show up later as premature rusting on the finished product."

Jan 1, 1987

By J. C. Judd

The U.S. Department of the Interior, Bureau of Mines investigated solvent extraction methods for recovering gallium from filtrates produced from sulfuric acid leaching of hydrometallurgical zinc residues. These filtrates typically had pH values of 0 to 0.5, too high an acid content for effective gallium recovery by traditional extractants. Of the nine extractants studied in batch tests, 0.3M octyl phenyl acid phosphate (OPAP) in a kerosene diluent was the most effective extractant for gallium recovery, extracting up to 99.9 pct of the gallium. This high extraction was possible when the iron in solution was maintained in the reduced ferrous state. Batch tests also showed that a 1.5M-H2SO4 strip liquor recovered 98 pct of the gallium from the loaded OPAP. A continuous solvent extraction system was designed and operated based on McCabe-Thiele analyses of equilibrium loading and stripping isotherms. When 12 L of leach filtrate containing 0.32 giL Ga and 20 giL Fe were pumped through the system in 32 hr, results showed that 95 pct of the gallium was extracted in four stages at an A:O ratio of 1:1. Stripping the loaded solvent with a 1.5M-H2S04 liquor recovered 94 pct of the gallium in four stages at an A:O ratio of 1:4. A two-stage, 50-pct-phosphoric acid strip successfully removed ferric iron from the OPAP, allowing high gallium extractions to be maintained.

Jan 1, 1990

By R. P. Aldis

A wide range of mineral-derived products are required by the electronics industry for it to function. In one form or another, almost all the known elements have been experimented with and tested for various electrical applications. The two major areas for which minerals are used in electronics are as conductors and semiconductors. Conductors provide the means to transport and distribute electricity, while the main application of semiconductors has been to manipulate electricity. Silicon is the most widely recognized semiconductor material, but gallium, indium, and germanium are rated as the most important metals to the semiconductor industry for future and near future technologies.

Jan 1, 1991

By C. Sunderman, G. Feagan, C. Stazick

Galvanic corrosion between dissimilar materials, such as steel and graphite, leads to safety concerns for many industries, including mining. In this study, researchers from the National Institute for Occupational Safety and Health (NIOSH) analyzed rock samples from two mines in the United States that exhibit electrochemical properties similar to graphite through laboratory measurements to investigate their observed in-situ influence on underground metal support. Uniform corrosion rates of mild steel coupons, inflatable bolt coupons, and friction bolt coupons galvanically coupled to rock samples were obtained using both potentiodynamic polarization and zero resistance ammetry. Increased uniform corrosion rates were witnessed between the coupled rock and steel system, over those of just the steel alone. Surface analysis of the metal samples showed the presence of pitting corrosion, reflective of bolt samples removed from partner mines. Corrosion pitting of ground support structures in contact with graphitic rock in underground mines poses safety concerns for mine workers by increasing the rate of corrosion and decreasing bolt strength over time and will be further investigated for intervention strategies.

Feb 1, 2023

By S. Qian

Galvanic corrosion is a potentially major concern associated with the application of stainless steel reinforcement which is in direct (electrical) contact with carbon steel reinforcement in concrete structures. Judicious use of stainless steel rebar in both new construction and rehabilitation of older structures is a viable, cost-effective option for extending service life and reducing maintenance costs. Questions, however, had arisen about the possibility of increased corrosion due to galvanic effects. This paper investigates the galvanic-coupling behaviours of three different types of stainless steel and carbon steel. Tests were performed both in electrochemical cells and with specimens in concrete inside an environmental chamber. The results show that oxygen reduction on stainless steel is the rate-determining factor for galvanic coupling of these two metals. It is much lower than that of passive carbon steel. As a result, the galvanic coupling of stainless steel with carbon steel will not increase the risk of corrosion of carbon steel reinforcement.

Jan 1, 2005

By J. E. Nesset, F. Rosenblum, J. A. Finch, R. Payant

ABSTRACT Under certain conditions of moisture and oxygen, sulphides can spontaneously self-heat. We tested a hypothesis that galvanic interaction between some sulphides can promote self-heating. Galvanic interaction is controlled by the rest potential difference between sulphides and particle size. A series of binary sulphide mixtures was tested. Individual sulphides and mixtures with low rest potential difference did not self-heat, but mixtures of high rest potential difference did. When testing pyrite-sphalerite mixtures, self-heating increased inversely with particle size, with the fineness of the pyrite governing self-heating, indicating the rate-limiting step is the reduction reaction. The results support the hypothesis that galvanic interaction contributes to sulphide self-heating. A possible mechanism based on hydrogen sulphide as an intermediate product is proposed. The understanding gained will be of interest to those involved in storage, shipping, and disposal of sulphides.

Jan 1, 2012

By M. Gagné, F. E. Goodwin

The mining industry represents a significant investment in infrastructure of which steel plays a key role. Many structures in a mine are made of steel including shaft structures (buntons, station steelwork and headgear); stope structures (roof supports, pipe hangers); haulageway structures (ore transfer stations, electrical stubbies); and surface structures (plant buildings, tank supports, pipe gantries, conveyor belts, stacks, stockpile structures, stairways and railings). Maintenance of structural components can often be difficult because of the environment, including those where corrosive fumes persist, or limited access, such as in shafts where access is limited, or to short maintenance shifts or where limited working space is available. Thus a cost-efficient, long-lasting and maintenance-free protection system for steel should be specified. Galvanizing provides the required high-quality, long-term corrosion protection to steel. Galvanizing provides protection in two ways, first as a physical barrier to corrosion and secondly by means of cathodic or sacrificial protection that is unique to zinc. The dual nature of corrosion protection provided by galvanizing significantly extends the service life of steel even in the most challenging environments. The unique corrosion protection properties provided by galvanized steel will be highlighted with global mining application case studies.

Jan 1, 2015

By John R. Riede

The use of radioactive gages in beneficiation plants is relatively new However, enough applications have been made so that it is now possible to positively state that these gages have definitely progressed from a laboratory device to a very rugged and reliable on stream process measuring instrument. Gamma Ray Gages of the type presently being used in the beneficiation industry consist of three basic components: (1) A source of radiation (2) A radiation detector (3) An electronic amplifier The source is usually a radioisotope such as cesium-137, or cobalt-60. This source, adequately protected and ruggedly mounted, is most commonly placed on one side of a pipe or vessel. The radiation detector is then mounted on the opposite side, Since the absorption of gamma radiation as it passes through various materials is a function of the density of the material, the change in radiation measured by the detector is proportional to the change in specific gravity of the product in the pipe or vessel. One popular type of detector in use today is a cell which converts radioactive energy directly into electrical energy1. This electrical energy, when amplified, presents a usable output for metering and control devices. There are, of course, many other components which are part of a working gamma gage installation, such as zero compensators, lead shielding, mounting brackets, equivalent absorbers, etc.

Jan 1, 1958

By E. A. Wieselmann

In 1970 Texasgulf (Australia) introduced natural gamma radiation logging of drill holes for exploration in the Hamersley Iron Province of Western Australia. Drill hole logs have allowed positive stratigraphic and structural correlations within complexly folded secondary hematite ore deposits and between individual iron ore deposits separated by distances in excess of seventy-five miles. A Neltronics model KPD logging system and gamma-ray sonde are being used to measure the natural gamma radiation of the enriched Brockman and Marra Mamba banded iron formations. The parent banded iron formations are composed of thick, chemically precipitated iron oxide, chert, iron silicate, and carbonate with thin intro-formational clastic horizons. These clastic horizons give a greater natural gamma radiation than the banded iron horizon, and each clastic horizon has a characteristic radiation profile related to its composition and thickness. Because the natural gamma-radiation profile is unchanged during secondary enrichment of the iron formation, the present stratigraphic position of each drill hole can be established and complex folding can be accurately traced in the sub-surface. Gamma ray logging of percussion drill holes has made feasible a significant reduction in diamond core drilling without loss of accuracy. At the same time, it has provided a means of rapid evaluation of complexly folded iron ore deposits.

Jan 1, 1975

By Elizabeth Carvalho L. Cardoso, Ademar B. Lugão, Sandra R. Scagliusi

This research investigated how gamma-radiation affected PP/HMSPP structural foams filled with biodegradable synthetic polyester PLA in terms of thermal properties, biodegradability and infrared spectrum. Polymers are used in various applications providing enormous quantities of wastes in environment and contributing with 20–30% of total volume of solid residues. Besides, shortage of plastics resins obtained from fossil base is addressing research and development toward alternative materials; environmental concerning in litter reduction is being directed to renewable polymers for manufacturing of polymeric foams. Biodegradable polymers, a new generation of polymers produced from various natural resources, environmentally safe and friendly, can contribute for pollution reduction. PLA (poly(lactic) acid)) was chosen to be blended with PP/HMSPP. Blends thereof were subjected to gamma radiation at 50, 100, 150, 200 and 500 kGydoses.Soilburialtestpointedtowardapartialbiodegradationofirradiated PLA-PP/HMSPP foams; other characterizations involved TG/DTG technique and FTIR assessments.

Mar 1, 2017

By P. Khattri

At Tata Steel, Coal is washed in gravity and froth flotation circuit at 13-15 mm size and below. Being coal is high in ash (~35%) and difficult washability characteristics (having high (~40 %) NGM at desired ash levels) needs more and timely quality data of ROM for effective optimization and process control. Conventional approach of supplying quality data takes 4-5 hours time. This means during this period, it is assumed that coal is having similar characteristics as of previous set and it is not possible to fine tune during this time which resulted in yield loss. Hence producing clean coal on agreed ash value consistently is a challenging task because of high NGM and variation in input quality. To overcome the problem of collection of representative sample and timely result a new technology was adopted Prompt Gamma Neutron Activation Analysis (PGNAA) technology which is basically an online analyser using Gamma rays as the source to measure the ash content in coal running on a conveyor which gives real time ash analysis. The details of this technological intervention are discussed in details in this paper. Keywords: near gravity material, PGNAA

Sep 1, 2012