Search Documents

By Jun Yi

In this paper, single-component gas sorption and transient diffusion processes are described within coal matrix exhibiting bimodal pore structure. The coal matrix is treated as a poroelastic medium manifesting swelling and shrinkage effects due to the sorption of gas under effective overburden stress. Gas transport is considered Fickian with molecular (bulk) and surface diffusion processes simultaneously taking place in the macro-and micropores of coal, respectively. The numerical formulation is intended to be explicit in nature to investigate the influences of sorption phenomena on the macropore volumes and on the overall gas transport for the cases of gas uptake by and release from coal. Results of the study show the presence of hysteresis during a sorption?desorption cycle of the gas. It is also found that the overall gas transport takes place at a rate significantly less than that in the macropores only. Thus the existence of a retardation effect in the overall gas transport is concluded. This retardation effect is primarily due to the micropore resistances, in particular gas adsorption, and is independent of the changes in the macropore volumes. It is shown that macroporosity of the coal matrix may change during gas transport due to combined effects of pressure and sorption-induced swelling or shrinkage of the coal. It is estimated that the macroporosity variation is non-uniform in space and time, as it is expected in reality, and typically taking values less than ±10 percent of the initial porosity.

Jan 1, 2009

By A. S. Adams

A GLANCE at the list of papers1 that have been published since 1920 on the general subject of flotation suggests the variety of ideas that exist regarding the underlying cause of the phenomenon.' Among these ideas, we find several coherent theories, but none that adequately and completely explain the phenomenon. Ralston2 and Bains3 suggested an electrical theory which has to do with the attachment of mineral particles to a bubble by the attraction of unlike electrical charges. This theory has its root in the fact that a bubble of air in pure water is electrified in such a way that the surface is negatively charged while the body of the water is positively charged. This result, which was first discussed by Helmholtz, also obtains when the water contains anything except a high concentration of hydrogen ions, or ions which are trivalent or tetravalent. The theory also holds that the mineral particles have positive charges on their surfaces, and so there is attachment between bubble surface and mineral particles by the old law of electrostatics, which states that unlike charges attract. CONTACT ANGLE AND OIL ATTRACTION The contact angle-the angle formed by a fluid-fluid boundary when both are in contact with a solid-has been indicted several times for complicity in the phenomenon of flotation. This angle is supposed to indirectly measure the surface energy of a solid. Thus if we have two fluids in contact with a solid, we may express the difference between the two fluid-solid tensions as equal to the fluid-fluid tension times the cosine of the angle between the two fluids.4 If the two fluids are in contact with the solid, this is, no doubt, an excellent way of establishing relative surface energies. However, in flotation, we deal with substances which are not wetted by water. What assurance have we, then, that the angle

Jan 1, 1928

By A. S. Adams

A GLANCE at the list of papers1 that have been published since 1920 on the general subject of flotation suggests the variety of ideas that exist regarding the underlying cause of the phenomenon. Among these ideas, we find several coherent theories, but none that adequately and completely explain the phenomenon. Ralston2 and Bains3 suggested an electrical theory which has to do with the attachment of mineral particles to a bubble by the attraction of unlike electrical charges. This theory has its root in the fact that a bubble of air in pure water is electrified in such a way that the surface is negatively charged while the body of the water is positively charged. This result, which was first discussed by Helmholtz, also obtains when the water contains anything except a high concentration of hydrogen ions, or ions which are trivalent or tetravalent. The theory also holds that the mineral particles have positive charges on their surfaces, and so there is attachment between bubble surface and mineral particles by the old law of electrostatics, which states that unlike charges attract.

Jan 1, 1928

By E. Watkins, S. J. Schatzel, K. Ajayi, V. Gangrade

The National Institute for Occupational Safety and Health (NIOSH) has been conducting research related to unconventional gas wells positioned in abutment pillars associated with active longwall mining in Southwestern PA. The Ventilation and Explosion Prevention Team at NIOSH is working toward predicting and characterizing a hypothetical casing breach and its effect on the safety and health of mine workers, gas well workers, and the general public. An important aspect of this research is to distinguish coalbed gas from shale gas in the mine environment as an indicator of a casing breach. Another noncoal gas source exists in the region in the form of underground gas storage fields which also have the potential to migrate towards mine workings. During a potential gas breach, the addition of excess natural gas to coal mine environments will exceed the anticipated ventilation loading and can create a mine explosion hazard. A methodology has been developed to distinguish these gas sources. Gas samples from the three sources were analyzed by gas chromatography, and interpretive methods were applied to distinguish the populations graphically and statistically. Bivariate plots using the hydrocarbon index and the normalized molecular ratios showed that the sources occupy different regions of the graphs. All samples of non-coal gas contained under 2% CO2, and all coal samples included greater than this amount. A multivariate T-squared (T2) test analysis relating comparing data in pairs showed a low p-value (dimensionality parameter) and a high T2 test statistic for all comparisons, indicating that these sources are different and distinct gas populations. Ultimately, stakeholders from the mining and gas production industries can utilize this method to identify gas sources and a potential casing breach.

Mar 2, 2022

By D. W. Gunkle

Processing of various ores and materials in a reducing atmosphere has been done for many years. However, the typical device currently used is a large, often high maintenance, expensive piece of equipment; the rotary kiln. While it is a very reliable and a proven technology, the rotary kiln also has its limitations. It is limited by its ability to process very fine materials without creating a huge dust loss to the air pollution control equipment. This leads us towards the development of an alternate technology; the Gas Suspension System. Gas suspension preheating of various materials has been in commercial use since the early 1950's, but recently has been expanded to include Gas Suspension Reduction. Laboratory experience has proven successful on several materials; Nickel Laterite Fines, Iron Ore Fines, Fluorspar, and Clays. The gas suspension reduction system has many advantages over the conventional reduction kiln when processing fines. They are; lower cost, more fuel efficient, able to process fines, less real estate required, etc.

Jan 1, 1998

By B. L. Moreau

Certain gas wells tend to form hydrates in the production tubing. This paper outlines a method developed and used by the Author's company to overcome the problem. The injection of glycol to control hydrates results in sufficient dehydration to allow the gas to be trans-ported through a field-gathering system b a treatment plant. Sub-surface injection of glycol also offers a method of introducing corrosion inhibitors into the gas stream. The major operating difficulties have been overcome and the system is now in use in the northeastern part of British Columbia.

Jan 1, 1958

By AIME AIME

A discussion of the Papers by Prof. H. Hubert, Liege, Belgium ; Mr. Tom Westgarth, Middlesbrough, England ; and Mr. K. Reinhardt, Dortmund, Germany, presented at the London Meeting, July, 1906, and printed in Bi-Monthly Bulletin, No. 12, November, 1906; pp. 910 to 930, 971 to 987, 1037 to 1163. MR. ADOLPH GREINER, Seraing, Belgium :-I have nothing special to add to Professor Hubert's paper except to say that there are some little things that it would be well to have cor-rected when the paper comes to be published. In dealing with the thermal efficiency of the engine, you will find that the 29.84 per cent was a very high one. Professor Hubert has forgotten those engines built under the Cockerill type, but he has referred to them in Appendix II. At our works at Cockerill we have built 63 engines, giving 63,000 h.p., and the other companies who have received licenses have built 113 engines, making 103,000 h.p., and aggregating 176 engines and 166,000 h.p. Eight years ago I had the pleasure of giving to the Institute the results obtained up to that time. Since then a good many engines have been constructed. In 1898 I thought a blast-furnace producing 100 tons of pig iron would allow 3,000 h.p. Professor Witz and Professor Hubert show that with the same production of pig the new engines take 3,800 h.p. out of the gas. At present at Cockerill we make 700 to 800 tons of pig iron per day, and we hope to have 26,000 h.p; in a few years. At present we have only half of that in gas-engines, but we hope to have in five or six years all the gas out of these furnaces to the number of 25,000 or 26,000 h.p. MR. Tom WESTGARTH, Middlesbrough, England:-My contribution is not a paper in the ordinary sense of the word, because I am sure you will agree with me that what I have written is only supplementary to the other two papers. The notes are schedules of the larger-size gas-engines built by the engine-makers, of 500 h.p. and upwards. If you look at the schedules you will find that in England gas-engines have be-

Jan 1, 1907

By G. H. Agnew

When water floods are initiated after gas-oil ratios have increased, the transition period from the start of injection until" the gas-oil ratios are returned to the solution gas-oil ratio may be important for either economic or technical reasons. The transition period is longest, and consequently most critical in water floods where injection is equal to withdrawals. This paper describes a theoretical basis for predicting the behavior of such a system and outlines a procedure for making the necessary calculations. The calculation procedure is illustrated for two actual cases: a line drive water flood and a five spot water flood. In each case there is a reasonable similarity between the actual and calculated performance.

Jan 1, 1960

By E. O. Bennett

When oil is takcn from a subsurface structure it is generally accompanied by gas. The gas thus produced represents the 1ighter hydrocarbons present in the original petroleurn accurnulation, which arc, insoluble at the reduced pressures created around a well when it is producing. In some cases the gas accompanying the oil may come from a gas-bearing stratum not in immediate contact with the oil. The amount of gas from the formation accompanying each barrel of oil is called the natural gas factor. Energy Causing Well to Flow The force causing the flow of fluid into a well when it is drilled into an oil-bearing structure is the pressure differential between the well bore and the formation. A pressure differential between the formation and the well may be set up in three different ways, as follows: (1) pressure due to gas in solution or in contact with the oil, (2) hydrostatic pressure due to water in contact with the oil (it may be either bottom or edge water); (3) pressure difference due to forcc of gravity. The greatest source of energy for producing oil from most oil fields, and the one over which the greatest control can be exerted, is the poten-tial energy in the gas under pressure in the formation. In any pool there is but a definite amount of gas available. Part of this gas may be in solution and a part in contact with oil. The amount of gas in solution in each bard of oil depends on the pressure and temperature in the formation and the characteristics of the oil. Whether the gas is in solution or in contact with the oil it is necessary to use the energy it, contains as efficiently as possible in order to obtain the greatest ultimate recovery from the pool. Bush1 states: Gas being the most efficient aid in moving the oil, it is important to prevent more of it from escaping than is necessary to remove the maximum amount of oil from the sands. The conservation of this energy is far more important to the producer of oil than his returns from sales of gas to distributing companies. The flowing life of the well is the most profitable period, and keeping the gas-oil ratio low, or keeping the

Jan 1, 1928

By L. D. van Dyk

The extraction of iron and lead from their oxides with a volatile organic ligand such as acetylacetone in the gas phase offers potential advantages of lower energy consumption, recycling of the extractant, recovery of pure metals, and a reduced environmental impact compared with conventional extraction processes. The influence of reaction temperature, ligand flow rate, and metal oxide levels on the extraction and rates of reaction of iron and lead from single metal oxide (synthetic haematite (Fe2O3) and synthetic massicot (PbO)) systems in a fluidized bed was studied. It was found that at the investigated acetylacetone flow rates, the influence of mass transfer was limited, but that the reaction suffered from reactant starvation. When the metal load increased the effect of starvation on the rate of reaction also increased. The reaction kinetics increased with an increase in temperature for both systems. At low metal oxide concentrations more that 80 per cent of the iron and lead could be extracted from their respective metal oxides after only four hours.

Jan 1, 2012

By L. D. van Dyk

The extraction of iron and lead from their oxides with a volatile organic ligand such as acetylacetone in the gas phase offers potential advantages of lower energy consumption, recycling of the extractant, recovery of pure metals, and a reduced environmental impact compared with conventional extraction processes. The influence of reaction temperature, ligand flow rate, and metal oxide levels on the extraction and rates of reaction of iron and lead from single metal oxide (synthetic haematite (Fe2O3) and synthetic massicot (PbO)) systems in a fluidized bed was studied. It was found that at the investigated acetylacetone flow rates, the influence of mass transfer was limited, but that the reaction suffered from reactant starvation. When the metal load increased the effect of starvation on the rate of reaction also increased. The reaction kinetics increased with an increase in temperature for both systems. At low metal oxide concentrations more that 80 per cent of the iron and lead could be extracted from their respective metal oxides after only four hours.

Jan 1, 2012

By A. D. Pienaar

The aqueous chemistry of niobium and tantalum compounds with hydrofluoric acid is a mature field of investigation. In contrast, very little attention has been paid to reactions of these compounds in non-aqueous environments. Similarly, reactions of elemental fluorine with niobium and tantalum compounds have received little more than cursory attention in literature. This work discusses the isothermal reaction kinetics derived from thermogravimetry, using a less redundant approach than is currently the standard. We also discuss the most likely kinetic models for this reaction.

Jan 1, 2012

By L. -C. Lai

A series of LaNi5-based alloys, with partial substitution of Ni by Al, Co, or V, were prepared The gas-phase hydrogen absorption kinetics and pressure-composition-temperature curves were measured The activation became easier and the plateau pressure was reduced as Ni was partially substituted by Al Substitution with Co reduced the hysteresis as well as the hydrogenation capacity, but enhanced the absorption kinetics Vanadium is often considered as a hydride former, but when it was added to LaNi5, it was found that V occupied the B site. A small amount of substitution of Ni with V led to a higher hydrogenation capacity and faster activation rate Based on these properties, an alloys LaNia 25CO0.5V0.1Al0. 15 was fabricated as an electrode. Compared with LaNi4.85Al0.15, it was found to exhibit faster activation, higher discharge capacity, and longer cycle life. The variation of the hydrogenation characteristics is discussed based on the physical and chemical properties of the alloying elements.

Jan 1, 1997

By Samuel S. Wyer

THE installation of the gas-producer power-plant in America has been so unusual that all engineers have viewed it with in¬terest; a large majority, however, regard it with a lack of con-fidence and many with positive distrust. Despite the fact that European engineers have usually been less inclined to take the initiative along experimental lines than are Americans, they have, nevertheless, developed the gas-producer plant to a very high state of efficiency to which they were forced by the neces¬sity of economy in fuel-consumption. The gas-producer power-plant is so common in Europe that engineers as well as the general public regard it with the same degree of confidence that is now universally placed in steam¬plants. Gas-engines, both small and large, are in general use there, and central stations, aggregating several thousand horse¬power, are quite numerous. The fact that gas-producer power-plants have received so little attention in America may be attributed to five conditions:-1', ignorance and prejudice; 2, newness of work; 3, in-

Mar 1, 1905

By Tateo Usui

In the course of carbonization of coal under a rising temperature condition, volatile matter (V.M.) is released. The kind and amount of V.M. released depend on the kind of coal. Components of V.M. are tar, hydrocarbons (CH4, C2H4, C2H6, C3H8), CO, CO2 and H2, which are released in this order as a function of carbonization temperature. When the carbonization of coal under a rising temperature condition is interrupted at a certain temperature, TC, max, semi-coal-char with residual V.M. is obtained. If some optimum interruption-temperature is chosen, small but most suitable amount of V.M., namely H2, is retained. When the semi-coal-char thus obtained is heated again under the same rising temperature conditions but up to more than TC, max (1), the residual V.M. is released from just around TC, max (1). We propose novel iron ore agglomerate bearing such semi-coal-char with some strength. While simple iron ore agglomerate bearing coal char will start the reduction reaction as solid-solid reaction at somewhat higher temperature, the proposed one will start the reduction reaction as gas-solid reaction at somewhat lower temperature but a little higher than TC, max. Samples of semi-coal-char and novel iron ore agglomerate bearing such semi-coal-char have been prepared and evaluated.

Jan 1, 2006

By Clinton M. Young

(Pittsburg Meeting, March, 1910.) I. INTRODUCTION. THE experiments herein. described were carried on in 1908-9 . by the State Geological Survey of Kansas. Some months before taking up work on black powder the Survey had resumed work on an interrupted investigation of explosions in coal-mines, a subject which is engaging the attention. of numerous investigators. An unusual number of serious disasters has directed to. the subject a study which discloses the disquieting fact that, in the. United States, the ratio of lives lost per ton of coal mined has been on the increase. Methods of coal-mining have changed to some extent with the great increase of output, attained in, comparatively recent years. These changes involve the working of very extensive mines, with increased difficulty of ventilation, increased accumulation of coal-dust, and. a very great increase in the amount of explosive used.. . This last point assumes truly startling proportions when it is carefully observed. In the fields of the Middle. West it is not now uncommon for a miner to use six ,kegs (150 lb.) of black powder in a "pay" of two weeks, while within the memory. of men still active, one keg (25 .lb.) would last two men for a " pay." So. great has . the use of explosives become in some fields that the skilled coal-miner is hard to find, and the coal is not mined, but blasted. A preliminary study of the subject. of explosions in coal-mines has. led to the belief . that the use of, large -quantities of explosives, in some cases by slightly-trained men, had not been * Associate Professor- of Mining Engineering, University of Kansas, Lawrence, Ran.

Aug 1, 1910

By T. A. Larssen

The efficiency in production of manganese ferroalloys is dependent on the gaseous reduction of the higher manganese oxides in the ores used as raw materials. The materials, descending in the furnace, will meet the furnace gas that contains significant amounts of CO(g) and reduce in subsequent steps, the last step being reduction of Mn3O4 to MnO. This step may to varying extent occur at temperatures exceeding 800 °C, i.e. in the active region of the Boudouard reaction. The gas reduction of Assmang and Comilog manganese ores were investigated in CO-CO2-atmosphere at temperatures up to 1000 °C. It was seen that decreasing ore size correlates to a lower reduction temperature and increasing reduction rate. Similar effect was observed with increasing CO-content in the gas atmosphere. Further, it was found that Comilog ore obtained a complete prereduction at 600 °C, whereas reduction of Assmang ore was not complete at 800 °C for the majority of the experiments.

By N. A. Ziegler

THE present publication is a continuation of the work on gas analysis, described in a paper presented before the Institute of Metals Division a year ago.1 While that paper was largely descriptive in character, dealing with the various parts of the apparatus and method of operations, the present one gives numerical data obtained as a result of a series of experiments with iron-carbon alloys. The apparatus and the methods applied are essentially the same as previously described, changes being only in minor details. Attention should be called to the fact that in the present work we are dealing with the gaseous mixtures obtained as a result of vacuum melting of various ferrous alloys. It should be understood that when the terms "degasified sample" and "products of degasification" are used, they refer to the sample remaining after the vacuum fusion of the alloy and the gaseous products removed therefrom, respectively. The writer does not wish to create the impression that the metallic products of this process are absolutely free from any gaseous elements, nor that the gases obtained are present as such in the original sample. These two points are not yet definitely known and are subjects for future investigation. The point, however, which has been established beyond doubt, is that all the gases dealt with come from the metallic charge and are present either in the charge as such, or are produced as a result of chemical reactions going on within the charge.. The suggestion that the gases are due to the reactions between the metallic charge and the refractory materials has no valid basis.

Jan 1, 1929

By N. A. Ziegler

THE present publication is a continuation of the work on gas analysis, described in a paper presented before the Institute of Metals Division a year ago.1 While that paper was largely descriptive in character, dealing with the various parts of the apparatus and method of operations, the present one gives numerical data obtained as a result of a series of experiments with iron-carbon alloys. The apparatus and the methods applied are essentially the same as previously described, changes being only in minor details. Attention should be called to the fact that in the present work we are dealing with the gaseous mixtures obtained as a result of vacuum melting of various ferrous alloys. It should be understood that when the terms "degasified sample" and "products of degasification" are used, they refer to the sample remaining after the vacuum fusion of the alloy and the gaseous products removed therefrom, respectively. The writer does not wish to create the impression that the metallic products of this process are absolutely free from any gaseous elements, nor that the gases obtained are present as such in the original sample. These two points are not yet definitely known and are subjects for future investigation. The point, however, which has been established beyond doubt, is that all the gases dealt with come from the metallic charge and are present either in the charge as such, or are produced as a result of chemical reactions going on within the charge. The suggestion that the gases are due to the reactions between the metallic charge and the refractory materials has no valid basis.

Jan 1, 1929

By Paul D. Merica

DURING the Dark Ages, when metallurgy was practiced by the alchemists, any unusual or disturbing variation in metallurgical operations was ascribed to the, presence, in the metals or ores, of an evil spirit, and it was necessary to exorcise and drive it out "by suitable incantations. In this day of science and of engineering, things still incomprehensibly go wrong in the metallurgist's work shop. The metallurgist is even now not unwilling to lay the blame for many such experiences at the door of something which intellectually- much resembles an evil spirit, "gas in the metal." The presence of gases in his metal, he knows, occasions him many very definite troubles which he can clearly distinguish and diagnose-why may it not be also responsible for those which he cannot so well understand?

Jan 1, 1931