Search Documents

A Novel Diagnosis and Evaluation Procedure for Flotation Plants

Sep 13, 2010

By O. G. Olvera, E. Asselin, D. Rival

Particle concentration distributions in a leaching tank have been estimated using a novel experimental approach that takes advantage of the galvanic interactions that occur between pyrite (FeS2) particles and a Pt electrode. The collision of FeS2 particles with Pt changes the open circuit potential measured with the electrode due to galvanic interactions. To discern particle collisions with the Pt electrode from experimental noise a simple analytical procedure was first adopted although the use of techniques involving frequency domain analysis is also briefly presented and discussed. Although this method is still under development, it is simple to implement and can yield valuable information regarding the hydrodynamic behavior of solid particles in stirred tanks in very short times. Finally, the advantages and drawbacks of the technique are discussed.

Jan 1, 2014

By J R. Ruiseco, D La Rosa, L Julian, W Hunt

The DeGrussa copper-gold deposit is located 900 km North of Perth. Copper-gold bearing massive sulfide lenses occur in lower greenschist facies meta-sedimentary and mafic volcanics of the Bryah Basin. Regional folding, faulting, and tilting of the stratigraphy primarily occurred during the Capricorn Orogen (Johnson, 2013). The Shiraz Fault and Merlot Fault are regional oblique-sinistral faults that offset the DeGrussa massive sulfides lenses into three fault blocks by ~350 m and ~120 m, respectively. A network of deposit-scale brittle-ductile faults splay from, and in one example are cut by, the Shiraz and Merlot faults. This results in localised ore displacement, selvage alteration and degradation of the rock mass integrity. Historically, only the Shiraz and Merlot Faults were modelled and validated during mining and grade control. The requirement for a comprehensive structural model became more relevant as mining became advanced and confining stresses on local rock mass became more complicated. The DeGrussa Structural Model has been developed to delineate areas of structural complexity and is an important tool in mitigating rockfall risk through well informed technical design. During this process, every accessible excavation was walked and structurally mapped. New workflows in Leapfrog Geo and new technology, including an app that runs on mobile phones streamlined the validation process. Drill hole orientation was a limiting factor during validation. At the time of writing this submission, the DeGrussa Structural Model consists of 34 faults, and is now an important tool for the Technical Service team when developing mine plans and schedules. Applied structural geology is often seen as exclusive to those with a PhD in the field. Faults at DeGrussa have been modelled and reconciled by a Mine Geologist and Geotechnical Engineer, using first principles geological characterisation. This is a simple process that demonstrates any geologist can contribute to a structural model, provided they understand the fundamentals of unbiased structural measurements and consistent record of observation

Mar 22, 2022

By L. Zhou, D. Bahrami

Mine ventilation is one of the most important aspects of mining operations in underground mines. It is critical to maintain and deliver required fresh air to the active areas to reduce the risk of overexposure to hazardous contaminants or explosive atmospheres. An unexpected or unknown event such as roof collapse, unexpected mine door closure/opening, a fire/explosion, or fan malfunction could adversely alter the airflow distribution within the mine ventilation network that could lead to a hazardous underground environment. Knowing the occurrence and location of such an incident is of critical importance. In this study, the authors developed a novel methodology to assist mine operators in quickly identifying the location of any abnormal airflow change within the network using the airflow changes at monitored airways. The concept is based on a direct derivative method developed by the authors. This paper provides the details of the developed method as well as numerical verification examples. The application of this method can benefit mine operators and safety personnel in making better decisions during a mine emergency response operation to mitigate hazardous conditions arising from an unexpected airflow disturbance

Mar 2, 2022

By Z. Jing, L. Qihou, C. Jun, L. Hui, Z. Yumeng

Three phases of Bi2O3 were first synthesized by extraction-stripping precipitation and post decomposition from BiCl3 leaching solution. The as-prepared Bi2O3 were characterized by X-ray powder diffraction (XRD), Fourier transform infrared spectra (FT-IR), scanning and transmission electron microscopy (SEM, TEM), UV-vis diffuse reflectance spectroscopy (UV-vis DRS), Brunauer-Emmett-Teller (BET) and X-ray photoelectron spectroscopy (XPS). The photocatalytic performances of the oxides were investigated by decomposing rhodamine B (RB) under visible irradiation. It shows that the Bi2O3 with different crystal structures and morphology were obtained under different decomposition temperature. The band gaps of as-prepared samples were 2.36, 2.41, and 2.78 eV for b-Bi2O3, a-Bi2O3, and d-Bi2O3, respectively, and the photocatalytic activities followed the order: b-Bi2O3 > a-Bi2O3 > d-Bi2O3, which was in good accordance with the photoluminescence spectra measurement results. The b-Bi2O3 exhibited the best photocatalytic performance which can effectively degrade 99.23% RB within 240 min.

Mar 1, 2018

By S M. Iveson, K P. Galvin, D Kumar

Dry separation of iron ore fines and other heavy minerals has previously been achieved using one of two main approaches. The first is an inclined table with an upward airflow via small holes to help form an autogenous dense medium. The second is based on fluidised beds comprising a dense medium formed by fine particles suspended in an upward flow of air. In either case, vibration can be introduced. This paper describes recent findings using a novel system referred to as the Sink-Hole Fluidiser, which utilises elements of both these two former approaches. This device consists of a conventional gas-fluidised bed of fine medium with a 1 mm aperture mesh located at the surface. This mesh contains relatively large holes that act as sink-holes. The fluidised media flows upwards through the sink-holes and then falls back into the fluidised bed via the fine apertures in the mesh. The particles being separated, which are much larger than the fine media, pass over these sink-holes, where they either sink or float. The sink-holes offer a more precise balance of forces, applied on a single particle basis, resulting in robust density separation.Experiments have been performed using 2.0–4.0 mm tracer particles of density varying from 2.4 to 4.8 relative densities (RD) separated in a 200 mm diameter Sink-Hole Fluidiser with a single 13 mm diameter centrally-located sink-hole. In this preliminary semi-batch work, it was found that the Sink-Hole Fluidiser was able to achieve sharp separations (Ep as low as 0.20). This work underpins the development of a new continuous steady-state Sink-Hole Fluidiser, applicable to the dry separation of iron ore fines.CITATION:Kumar, D, Iveson, S M and Galvin, K P, 2017. A novel sink-hole fluidisation method for dry separation of iron ore fines, in Proceedings Iron Ore 2017, pp 221–226 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By B Muller

The disposal of tailings has become a greater issue due to the changing economics of mineral extraction. The processing of lower grade deposits and tougher environmental regulations has led to the selection process for tailings disposal options becoming more complicated. Current selection methods are too time consuming or too easily manipulated for inexperienced users to use successfully. This paper examines a different method for the initial selection of a tailings disposal system, using a numerical system that was introduced into the mining method selection field. The numerical method system was compiled by reviewing previous work done on the positive and negative aspects of the tailings disposal methods used by the coal and metallurgical mining industries. Assessing the common trends and design aspects of each of the methods was undertaken and a ranking was designed to explain how well suited the tailings disposal methods are to a situation. The tool successfully analysed sites using common data to indicate methods for disposal that would have provided minimal technical problems, low environmental risk and been practically possible. The tool also proved successful in identifying critical areas that would need further investigation. This new system was tested on some disaster case studies from around the world in order to show that it could have successfully selected a different method for tailings disposal that would have prevented the disaster.

Sep 26, 2011

By Gang Mei, Nengxiong Xu, Yanlin Zhang

After open-pit mining finishes, an iron mine with steeply inclined ore-bodies will generally transform to underground mining. Non-pillar sublevel caving method, with horizontal slice mining from up to down, is commonly used for mining deep ore-bodies under the open-pit bottom. As horizontal slice mining proceeds, a gradually enlarging goaf will be formed under the open-pit bottom, the rocks surrounding the handing and heading sides of the goaf will collapse continuously, and then these results in rock-mass failure with large deformation and displacement in the open-pit slope. Based on FLAC3D, a modeling approach to predict pit slope deformation and failure induced by transitioning open-pit to underground mining is proposed in this paper. This method mainly consists of three procedures of modeling, i.e., mining modeling, landslide modeling, and filling modeling, of which landslide modeling is the core of the proposed approach. In the procedures of modeling with FLAC3D, iteration non-convergence is taken as a local failure criterion of pit slope. When iteration calculation cannot converge, the sliding modeling will start by deleting some elements with large displacements, and finish until convergence. Before modeling landslide, several displacement contours of rock-masses in the pit slope are searched out, and each contour is an approximate possible sliding surface of the open-pit slope. From these contours, the most proper one is selected as the slope sliding surface by using the iteration calculation convergence and minimum element deletion as the judgment condition. Landslide modeling is then realized by removing the elements outside the slope sliding surface. Finally, to demonstrate the effectiveness, the proposed approach is used to simulate the process of open-pit to underground mining at Yanqianshan Iron Mine, and to predict the deformation and failure characteristics of open-pit slope during underground mining. The case study results show that: the prediction of the slope stability determined by using our method is consistent with that calculated by using the limit equilibrium methods.

Jan 1, 2015

By Dale S. Preece

The computer program. DMC Qistinct Motion &de), which w&s developed for simulating the rock motion associated with blasting, has been used to study the intluence of row delay timing On rock mOtiOn. The munerical simulations correspond with field observations in that vmy short delays (< 5Oms) and vety long delays(> 3oOms) produce a lower percent-cast thao a medium delay (100 to ZOO ms). The DMC predicted relatio&lp between row delay timing and percent-cast is more complex than expected with a dip in the auve where the optimum timing might be expected. More study is required to gain a full undasranding of this phenomenoo.

Jan 1, 1994

By Ana E. Bohé, Georgina De Micco, Juan P. Gaviría, FEDERICO J. POMIRO, Gastón G. Fouga

Chlorination and carbochlorination processes have industrial applications in metallurgical activity for extraction and purification of uncommon metals such as rare earth elements (REE). This study reviews the chlorination and carbochlorination reactions of light REE (LREE) oxides with chlorine considering the thermodynamic, stoichiometric, and kinetic aspects of the reactions. Lanthanides between lanthanum to gadolinium were considered as LREE, in agreement with previous literature, and the results were detailed in this review. LREE were analyzed taking into account their oxidation states and were divided into three groups accordingly. The results presented show that, although the LREE are chemically similar, their behaviors during the reactions with Cl2 and Cl2–C, and the different LREE-O–Cl compounds formed, have particularities. It was observed that gadolinium, in both thermodynamic calculations and experimental results, presents some differences, and it can be considered intermediate between light and heavy REE; i.e., reactions between LREE2O3 and Cl2(g) begin at approximately 250 °C, except for Gd2O3 that begins at 327 °C. The present work will contribute to a better understanding of the chemistry of LREE oxides and Cl2 under different conditions and the products obtained in the LREE–O––Cl2(g) and LREE–O–C–Cl2(g) systems.

Oct 15, 2021

By Morgan M. Sears, Gamal Rashed, Michael M. Murphy, Brent Slaker

In this study, a parametric study was conducted using FLAC3D numerical models to examine the impact of oblique loading, generated from seam dip, on the strength and the failure propagation pattern of a stone pillar using two simplified geometry types. In type 1, the sidewalls of the pillars were assumed to be perpendicular to the roof and the floor, while in type 2, the sidewalls of pillars were assumed to be vertical. The complex pillar geometry in dipping mines was frequently modeled using these two geometries. To capture a complete picture of the effect of seam dip on pillar stability, the modeled width-to-height (W/H) ratio of the pillars, in situ stress field, and pillars roof/floor interfaces were systematically varied to account for the potential distribution of values for these parameters across the underground stone mines in USA. Results from the numerical modeling indicate that dipping pillars have reduced strength compared with horizontal pillars. Also, an asymmetric failure propagation pattern could be obtained depending on an interaction between the W/H ratio, seam dip, in situ stresses, and pillar geometry.

Feb 5, 2021

By Morgan M. Sears, Gamal Rashed, Michael M. Murphy, Brent Slaker

A parametric study was conducted using FLAC3D numerical models to examine the impact of oblique loading on the strength and yield pattern of a stone pillar using two simplified geometry types. In type-1 the side walls of the pillars were assumed to be perpendicular to the roof and the floor, while in type-2 the side walls were assumed to be vertical. These two geometries are frequently used to simplify/model the creation of pillars in dipping mines. Results from the numerical modeling indicate that dipping pillars have reduced strength compared to horizontal pillars, and they are at an elevated risk of failure. Also, an asymmetric failure propagation pattern could be obtained depending on the interaction between the pillar width/height (W/H) ratio, seam dip, in situ stresses and pillar geometry.

By K. C. Naidoo

There are two main types of densifying cyclones currently available in the market, namely polyeurethane (PU) and ceramic. The PU densifying cyclones are currently used throughout the Grootegeluk complex and coal beneficiation in general. It has been identified that PU densifiers wear relatively fast depending on the operating pressure and need to be replaced frequently as a result. The motivation for this paper is to achieve an increase in the densifying cyclone lifetime through less wear and an increase in efficiency resulting in the ability to build higher relative densities (RD) more quickly. This will allow for a reduction in downtimes due to replacing densifying cyclones as well as building RD and a reduction in the operating costs associated with replacing worn densifying cyclones. Some of the major findings of the study indicated that the ceramic cyclone theoretically undergoes less wear than the PU cyclone, but since wear is application-specific and was evaluated, the wear on the polyurethane cyclone was found to be minimal. The RD differential is higher on the PU cyclones than the ceramic cyclones, showing that the PU cyclones perform better in a densifying application. This is the first test conducted on this application and type of cyclones. It should therefore be noted that having the PU cyclone significantly outperform the ceramic cyclone was not expected, due to the only change being the material of construction. This is an indication to take the material of construction into account when selecting cyclones as it can have a significant impact on the cyclone performance in specific applications. Keywords: Ceramic, cyclone, densifying, density, dense medium, polyurethane, wear

Jan 1, 2020

By T R. Stacey

South Africa has a long history of rockbursts, some 100 years. During this time much research and many developments have taken place in the country to limit the occurrence of rockbursts, and to mitigate their effects. In this paper I shall present a personal view of what I consider to be important achievements, and contributions made. Some of these are: planning of stope layouts, and the use of strike barrier pillars; recognition of energy as a key factor, the use of the energy release rate ERR as a layout planning criterion, and development of MINSIM for calculation of ERR and stope planning; sequential grid stope layouts; use of backfill for stope support; and, development yielding support elements, and dynamic testing of stope and tunnel supports. The record shows the establishment of a rock engineering research powerhouse over a 40 to 50 year period and, unfortunately, the complete breakdown of this capability in the subsequent 10 years. CITATION:Stacey, T R, 2018. A personal review of South African rockburst research, experience and lessons learnt, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 5–16 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By K. Richardson

Although the De Beers group has a long history of placer mining on land, the group only became actively involved in deep water marine diamond exploration and mining in 1983 with the formation of DeBeers Marine. Full-scale commercial mining commenced around1991. Since then, the group marine mining capability has grown into a formidable fleet of 8 large deep water (>70 m) mining vessels, as well as other special purpose geosurvey platforms. Marine diamond production by the group is expected to be just short of 1 million carats in 2006. De Beers operates across the entire value-chain spectrum from geology and geosurvey, through sampling to mining, and finally ore processing into high value concentrate. Supporting these operations involves significant service activities such as maintenance, security, logistics and environmental management. Specific challenges exist in terms of developing or acquiring appropriate technology for marine mining. These challenges have resulted in De Beers operating extensive in-house R&D and projects departments, as well as drawing extensively from technology partners. An array of computational and test facilities is also available to support R&D and projects activities. Hydrotransport in various guises is key to the current approaches to marine mining and ore processing. Use is made of airlift and centrifugal pumping for hydraulic hoisting of very coarse gravel, while splitters, launders, dewatering, elutriators, jet pumps, centrifugal pumps, dense medium circuits, pipeline systems, and instrumentation for coarse abrasive particles are used extensively in the ore processing plant.

Jan 1, 2007

By C. Musingwini

The South African mining industry continues to be a major source of employment at a time when at least 25 per cent of the working age population is unemployed. At the same time the industry faces a skills shortage in many of the disciplines necessary for its future health. The University of the Witwatersrand, University of Pretoria, University of Johannesburg, and University of South Africa have historically produced mining graduates for the South African industry, with any shortfall being met by the recruitment of overseas graduates. More recently the global shortage of engineers and other mining industry professionals has seen a reversal of this trend and a very significant emigration of well-educated and highly skilled personnel. The traditional career path for mining graduates is in production and mine management. However, there is the parallel and possibly more pressing need for specialized skills in such fields as ventilation, rock engineering, mine planning, mineral resource evaluation, and mineral asset valuation. It is in these essential areas that chronic shortages continue to hamper the development of the industry and may well frustrate its ambitions to be safe, healthy, and profitable into the future. The permeability of skills across sectorial boundaries within the mining industry requires that skills shortages in the platinum sector are not looked at in isolation, but within the context of the entire industry. This paper reviews the efforts being made by the universities at both undergraduate and postgraduate levels to meet the needs of the South African mining industry, in terms of the required numbers and the range of specialized skills.

Jan 1, 2012

Falls of ground (FOG) still account for around 35 per cent of all fatalities in underground southern African mines. To help reduce FOG, appropriate support technology needs to be implemented, and a mindset and cultural change are required to make a significant change. Discipline plays a major role and needs attention, whilst appropriate first-world support technology is available to assist in the reduction of injuries and the improvement of productivity. Section 54 mine stoppages due to FOG are costly. Appropriate support should reduce these unnecessary stoppages. Coal mining has adapted leading support technologies over the years. Platinum and chrome mines have shown significant moves towards adopting leading and appropriate support technologies, seeing noteworthy changes in injury statistics for the better. In typical conventional underground mining operations, the use of temporary support components offers some protection to workers while the permanent and generally more elaborate support systems are installed or constructed. Nonetheless, FOG continue and still result in injuries to people. The author wishes to explore the options and practicality of making use of new-generation support products and technology to provide not only safer support operations, but to also enhance productivity at the working faces. This paper will examine the use of appropriate support technology as a means to making the working stope or development end a safer and more productive workplace.

Jan 1, 2012

By Descarreaux. Jean

"The Abitibi volcanic belt was sampled along a cross section extending from Matagami to a point east of Rouyn. A few samples were also collected in Louvicourt township, Quebec. The major elements were determined for 344 samples, and rock names were defined using normative minerals. The analytical data were studied by means of variation diagrams. The Abitibi volcanic belt is characterized by rocks belonging to both the tholeiitic and calc-alkaline magmatic series, but they show some differences as compared to some typical reference series, particularly those from Japan. Basalt is the predominant rock type and accounts for 44 per cent of the sampled outcrops. The volcanic rocks are relatively poor in K2O and TiO2. Regionally, the volcanogenic copper-zinc mineralization is associated with the calc-alkaline volcanic sequences. Locally, within such sequences, some types of abnormal deviations from the averages are recognized only in association with the copper-zinc mineralization. The anomalies are ascribed to hydrothermal alteration consisting of the introduction of MgO and removal of N a20; enrichment in K20 is also observed where zinc mineralization predominates. Examples of such anomalous zones show that, in places, this alteration phenomenon can be quite extensive. Petrochemical characteristics can be used as geochemical ore guides in exploration programs."

Jan 1, 1973

By G B. Arehart, J L. Mauk

Quartz veins from the Martha Hill epithermal gold-silver deposit, Waihi, commonly exhibit crustiform banded textures. Visual differences observed between bands are primarily the result of a 1 to 1500 ¦m variation in quartz grain size. Quartz band textures are dominated by anhedral interlocking quartz mosaics, commonly associated with minor adularia and sulphide phases; these textures are interpreted to be products of amorphous silica crystallisation. The occurrence of rhombic adularia suggests that prolonged boiling influenced parent fluids. In contrast, the presence of coarsely crystalline bands, made up of subhedral to euhedral quartz grains, infers primary crystal growth from solution; evidenced by the occurrence of growth-zoned quartz within these bands. There is a narrow range of 3.3ë in d18Oquartz between maximum and minimum isotopic values for the deposit. Significant overlap in d18Oquartz values are observed between the Martha and Welcome lodes. However, statistically significant and commonly systematic differences do occur between individual bands analysed in most samples. Temperature fluctuations may be the dominant factor responsible for observed inter-band variation.

Jan 1, 1995

The relationship between the maceral composition of coal and the strength of the coke produced from that coal has received a great deal of attention in recent years.Studies using two Bulli Seam coals, and blends of Bulli and Wongawilli Seam coals, from the IIIawarra Measures of the Southern Coalfield of New South Wales were carried out.The optimum range of vitrinite was found to lie between 45 per cent and 60 per cent (mineral matter free).Above and below this vitrinite range coke strength deteriorated. Coke strength indices increased with rank, and the optimum vitrinite content increased with an increase in rank. These changes require confirmation as trends by testing a third level of rank. It was noted that vitrinite content decreased with an increase in the specific gravity of separation of the coal.Use of petrographic analyses will increase confidence in choosing coals for coking, provided the coals are well known. Such analyses offer the possibility of greater flexibility in coal purchases and the possibility of producing a marketable blend from coals, which have limited market potential. Critical base coals for blends can be conserved.Significantly more work is required before coal reserves can be utilized to optimum advantage. This work would require extension of the studies discussed in this paper and, in particular, the testing of a wider range of rank.

Jan 1, 1971