Search Documents

By Tony P. Suckling

This paper describes an investigation into the bleeding behaviour of bentonite slurry observed on a trial diaphragm wall panel. The bleeding is thought to be due to the bentonite experiencing a chemical reaction leading to settlement of the solids within the fluid, possibly as a self-weight consolidation process. The trial panel was constructed in a busy airport environment where many different chemical products are used for de-icing the aeroplanes, runways, apron areas, vehicle access and pedestrian routes. The relationships between slurry contamination, bleeding, bentonite hydration time and filter loss behaviour were examined as no relevant published literature could be found. The results show that the amount of bleed strongly depends on both the degree of contamination and the hydration time. It is concluded that bentonite fluids should be allowed to sit in the storage tank for at least 24 hours after mixing, and that the filter loss test is a quick and effective method to determine the potential for bleeding of contaminated slurries.

Jan 1, 2011

By S. Tan

In this paper, several commonly used computer truck dispatching criteria are evaluated. A computer-oriented truck dispatching and production simulator was developed to provide data for comprehensive cross comparison among the dispatching criteria. The definitions, primary considerations, characteristics, and performances of these dispatching criteria were investigated. From the simulation results, it was concluded that, in general, no one criterion can dominate all others. All basic dispatching criteria including minimizing truck waiting time, minimizing shovel waiting time, minimizing truck saturation, maximizing truck momentary productivity, or truck routes optimization provide a local optimal solution. To obtain a direct global optimization solution for this complex stochastic process does not appear to be likely. Therefore, the search for an optimal dispatching criterion that will fit all conditions may not be realistic. However, based on the simulation results of the mine operation, several dispatching criteria which have good potential to increase performance can be selected. It may be necessary to search for the best combination of these truck dispatching criteria for a given situation. For example, a truck flow measurement such as the truck clustering factor at shovels can be used as a switch parameter to change from one criterion to another. The values for the switch parameter at which actions should be taken to change the criterion can be established through simulation programs.

Jan 1, 1992

By Paul J. Sabatini, Yazen A. Khasawneh

"A Demag CC1800 crawler crane was partially erected on crane mats adjacent to a seawall when settlements near a corner of the crane mat area were observed to be slightly larger than previously assessed. A ground improvement program including installation of dry soil cement mix (DSM) piers was implemented to improve soil bearing capacity. Due to near-surface obstructions, only 75 percent of the DSM piers were installed to the design depth. Because of the partial installation of the DSM piers, an evaluation of the crane pad stability and the effect of the crane loading on the stability of an adjacent 10-ft high concrete seawall, which was believed to have limited (if any) reserve capacity, was required. A two-dimensional finite element model was developed to evaluate the responses of the partially improved ground and the sea wall to the loads imposed by the crane. Geotechnical site investigation and laboratory testing programs were performed to better define the subsurface conditions near the area where settlements occurred and to provide the required mechanical parameters for the soil constitutive model. Analysis results indicate that total and differential settlements of the crane pad and the increase in load on the seawall were tolerable provided limited excavation and replacement of weak dredged soils outside the DSM area would be implemented.INTRODUCTION & BACKGROUNDA Demag CC1800 was erected on 8 ft × 16 ft crane lattice mats at about 12 ft from an existing seawall. Approximately 3.5 in. of subsidence was observed at one corner of the crane mats, while the crane was partially erected and stationary. The approximate location of the crane mats with respect to the existing seawall when the subsidence occurred is shown on Fig. 1.The seawall consists of a reinforced concrete wall connected by reinforced concrete bents to a composite section of sheet pile wall; the total depth of the seawall is about 29 ft. The bents are spaced at about 20’4” and supported by five piles at each bent location. The composite sheet pile consists of concrete and a sheet pile section with a reinforced concrete wale section. The retaining wall is about 10 ft in height and is supported at three levels. The first support level comprises a 2-½” diameter steel rod near the top of the wall spaced at 40’8” the second and third level supports comprise 1-½” diameter steel rods spaced at about 5’6”. The second level support is inclined at about 10 degrees below horizontal and the third level support is oriented horizontally through the wall footing. A schematic of the seawall section is shown on Fig. 2.A geotechnical site investigation was implemented soon after the subsidence was observed. The program included advancing four borings to a depth ranging from 16 ft below ground surface (bgs) to about 30 ft bgs. In general, the investigation showed sandy material (likely fill that was used behind the retaining wall) from the ground surface in two borings located immediately behind the retaining wall. The other two borings furthest from the retaining wall showed very soft to soft clay (possibly dredged material) from the ground surface to a depth of about 10 ft bgs. Based on this information, the ultimate bearing capacity of the subsoils was estimated to range from 1,200 to 2,000 pounds per square feet (psf). From the anticipated crane loading (weight of the crane and loading lifts), a minimum allowable bearing capacity of about 1,500 psf would be required for safe operation. To achieve the required bearing capacity a ground improvement program was selected and implemented."

Jan 1, 2017

By J. D. Miller, C. L. Lin

Appropriate software and hardware necessary to adapt a x-ray CT analyzer for determination of coal washability has recently been developed and sucessfully tested for well characterized samples under laboratory conditions. Evaluation of the CT-based analyzer under simulated on-line conditions is also presented to verify the on-line capabilities of the newly developed x-ray CT analyzer for the control of coarse coal cleaning circuits. The investigation shows that the data obtained from CT washability analyses compare favorably with experimental sink-float data. Further, image frequency was considered to evaluate the CT-Based coal washability analyzer for simulated on-line conditions. Specifically the number of observations (image spacing) needed for accurate sampling and the total time required to perform the calculations for a representative data set were determined.

Jan 1, 2001

By Grady B. V O, Cavell K. J, Ault A. R, Newman O. M G, Malcolm J. McPhersqn

Cyclic voltammetry (CV) has been evaluated as a technique for monitoring the quality of an industrial zinc sulphate electrolyte. The basis of the method involves measuring a change in the polarisation of the zinc nucleation reaction at an aluminium surface and relating this to the impurity content and/or the overall quality of the electrolyte. Specifically, the technique aims to be able to indicate and quantify detrimental synergism between impurity elements, something which traditional analytical techniques are incapable of providing. The technique has found some success with regard to monitoring glue additions in a range of metal electrolytes. It has been found that investigations by a number of workers over the past 15 years have produced variable and often misleading results due to the inadvertent use of commercial purity aluminium working electrodes. It has been shown that impurity elements in the working electrode can give rise to a range of responses that are not obtained when pure aluminium is used and that the response is variable due to the lack of surface homogeneity of commercial purity aluminium electrodes. Furthermore, it was demonstrated that previous detection limits reported in the literature were based on the presence of additional peaks in the cathodic scan and not polarisation effects. The results of this study have shown that when a pure aluminium working electrode was used, the method was incapable of detecting any change in polarisation for an electrolyte containing three common impurities (Co, Ni and Ge), at concentrations that would significantly reduce optimum electrolytic performance. A range of methods was tried to sensitise the technique, including raising the temperature and acidity, and adding antimony in order to induce some synergism. In all cases the polarisation response was unchanged. Consequently, apart from the commercialised application for monitoring additions of antimony and levelling agents such as glue, CV has very limited application as an electrolyte screening technique.

Jan 1, 1993

By M. A. Trevits, J. E. Urosek, A. C. Smith, M. P. Valoski

The National Institute for Occupational Safety and Health (NIOSH), in partnership with the Mine Safety and Health Administration (MSHA), is conducting research to test, evaluate, improve or modify coal mine fire-fighting strategies and methodologies through large-scale tests. Since wood is the second most abundant fuel available during a coal mine fire, it was decided that series of large-scale wood crib fire tests were needed to measure the products of combustion and to observe the capability of commonly available direct application fire suppression equipment, namely, fire extinguishers, water and gas-enhanced foam. This paper discusses the wood crib fire tests, provides insight into the products of combustion and describes observations made during the application of the fire suppression agents.

By M. A. Trevits

The National Institute for Occupational Safety and Health (NIOSH), in partnership with the Mine Safety and Health Administration (MSHA), is conducting research to test, evaluate, improve or modify coal mine fire-fighting strategies and methodologies through large-scale tests. Since wood is the second most abundant fuel available during a coal mine fire, it was decided that series of large-scale wood crib fire tests were needed to measure the products of combustion and to observe the capability of commonly available direct application fire suppression equipment, namely, fire extinguishers, water and gas-enhanced foam. This paper discusses the wood crib fire tests, provides insight into the products of combustion and describes observations made during the application of the fire suppression agents.

Jan 1, 2009

By David E. Thompson, Andrew F. McKown, Herbert H. Einstein, Amr S. Azzouz

INTRODUCTION Design of supports for underground chambers in rock has undergone considerable development. This becomes evident when comparing support dimensions of subway station caverns built in the U.S. over the past fifteen years. The Porter Square Station cavern, which is a part of the Massachusetts Bay Transportation Authority (MBTA) Red Line extension, is the latest in this series. It is approximately 168 m (550 ft) long, 21 m (70 ft) wide, and 14 m (45 ft) high, and has a permanent support of light steel ribs imbedded in a 0.4 m nominal (15 in) shotcrete lining. An extensive construction control instrumentation program made it possible to evaluate the performance of the cavern and its support. This evaluation, which is presented in this paper, was the objective of a research project sponsored by the Urban Mass Transportation Administration (UMTA) and jointly conducted by Haley and Aldrich, and MIT. The actually used design procedure was compared with other approaches, notably procedures based on Finite Element analyses and empirical rock mass classification methods. Support dimensions predicted with all these approaches were compared to the actual support and its performance.

Jan 1, 1983

By V. Yahorava

Ion exchange is considered to be an effective technology for the removal of various impurities from cobalt advance electrolytes. With the correct choice of resin, ion exchange can consistently remove the required impurities to the levels for the production of high-grade cobalt metal. Although ion exchange was in the past used primarily for nickel removal, more recently it has been also considered for the removal of copper, zinc, and cadmium. Generally, granular ion exchange products are used, but Mintek is currently evaluating ion exchange fibres for a number of applications, including the removal of copper from cobalt advance electrolytes. Fibrous ion exchangers have major advantages compared to granular resins in that they have significantly higher reaction rates, and wash water volumes could be limited. Granular and fibrous ion exchangers were evaluated and compared for the removal of copper from cobalt advance electrolyte. A synthetic electrolyte containing 50 g/L cobalt and 50 mg/L copper was used for the test work. Equilibrium isotherms, mini-column tests, and split elution tests were done. The results were used to size a full-scale operation to treat 100 m3/h of electrolyte. The potential cobalt losses or recycle requirements were estimated, and data to calculate indicative operating costs for each adsorbent was generated. This information was used for a techno-economic comparison of granular and fibrous ion exchange systems for the removal of copper from cobalt advance electrolyte.

Jan 1, 2014

By Éder Domingos Oliveira, Carlos Antonio Morais, Ruberlan Gomes Silva

The objective of this study is to assess the impact of different reagents, such as limestone, lime, magnesium oxide, and sodium hydroxide, in experiments carried out in the single purification step and in two consecutive purification steps by raising the pH of a rare earth sulfuric liquor with the aim to remove or reduce the impurity concentrations in the rare earth sulfuric liquor. The choice for the best purification condition was made based on the minimum loss of rare earth elements (REEs), reagent consumption, and residue generation. The exploratory experiments show that it takes place in the two consecutive purification steps, the first one consists in dosing the limestone pulp until it reaches a pH of 3.5 followed by an addition of a lime pulp reaching a pH of 5.0. Under this condition, the results were a total removal of Fe3+, PO4 3− , and Th4+ ions and a reduction of 99%, 87%, and 37% w/w in the Al3+, UO2 2+, and SO4 2− concentrations, respectively, in the purified rare earth liquor. Furthermore, the lowest REE losses (8.3% w/w) and reagent consumption (4.3 kg/m3 ) and also a low residue generation (7.5 kg/m3 ) were observed in this condition. Despite reaching similar results regarding impurity removal, the experiments done with the addition of limestone, lime, magnesium oxide pulps, and sodium hydroxide solution in the single purification step, where the pH was raised to 5.0, presented higher REE losses (64.9%, 42.5%, 44.8%, and 60.9% w/w, respectively) and a higher residue generation (43.2, 25.1, 11.1, and 13.6 kg/m3 , respectively). This occurred due to the co-precipitation of salts containing rare earth elements in their composition. The experiments conducted with limestone, lime, and MgO resulted in a higher consumption of reagents, while the same result was observed when NaOH was used (4.3 kg/m3 ). In the experiments carried out with the addition of magnesium oxide and sodium hydroxide, the respective purified rare earth liquors presented a high concentration of magnesium, sulfate, or sodium, which could impact the quality of the marketable rare earth salts, whereas the salts obtained under the best condition observed in this study seem to be amenable for use as raw material in an attempt to obtain rare earth products with an acceptable chemical quality.

By Éder Domingos Oliveira, Carlos Antonio Morais, Ruberlan Gomes Silva

The objective of this study is to assess the impact of different reagents, such as limestone, lime, magnesium oxide, and sodium hydroxide, in experiments carried out in the single purification step and in two consecutive purification steps by raising the pH of a rare earth sulfuric liquor with the aim to remove or reduce the impurity concentrations in the rare earth sulfuric liquor. The choice for the best purification condition was made based on the minimum loss of rare earth elements (REEs), reagent consumption, and residue generation. The exploratory experiments show that it takes place in the two consecutive purification steps, the first one consists in dosing the limestone pulp until it reaches a pH of 3.5 followed by an addition of a lime pulp reaching a pH of 5.0. Under this condition, the results were a total removal of Fe3+, PO4 3− , and Th4+ ions and a reduction of 99%, 87%, and 37% w/w in the Al3+, UO2 2+, and SO4 2− concentrations, respectively, in the purified rare earth liquor. Furthermore, the lowest REE losses (8.3% w/w) and reagent consumption (4.3 kg/m3 ) and also a low residue generation (7.5 kg/m3 ) were observed in this condition. Despite reaching similar results regarding impurity removal, the experiments done with the addition of limestone, lime, magnesium oxide pulps, and sodium hydroxide solution in the single purification step, where the pH was raised to 5.0, presented higher REE losses (64.9%, 42.5%, 44.8%, and 60.9% w/w, respectively) and a higher residue generation (43.2, 25.1, 11.1, and 13.6 kg/m3 , respectively). This occurred due to the co-precipitation of salts containing rare earth elements in their composition. The experiments conducted with limestone, lime, and MgO resulted in a higher consumption of reagents, while the same result was observed when NaOH was used (4.3 kg/m3 ). In the experiments carried out with the addition of magnesium oxide and sodium hydroxide, the respective purified rare earth liquors presented a high concentration of magnesium, sulfate, or sodium, which could impact the quality of the marketable rare earth salts, whereas the salts obtained under the best condition observed in this study seem to be amenable for use as raw material in an attempt to obtain rare earth products with an acceptable chemical quality.

By T. W. Beck

Overexposure to respirable dust remains a widespread health hazard to roof bolter occupations in underground coal mines. Recently implemented mist drilling technology was evaluated for its effectiveness in controlling respirable dust exposures for roof bolting personnel. This work presents the findings from NIOSH field and laboratory studies comparing respirable dust levels on mist drilling roof bolter machines to dust levels measured on machines using a conventional vacuum drilling system. Gravimetric and instantaneous respirable dust samples were collected for multiple drilling cycles. These dust measurements were used to assess the potential dust control capabilities relative to conventional drilling. Controlled laboratory tests found 0.3 mg/m3 more respirable dust with mist drilling than with the conventional vacuum method. A separate field investigation of the two techniques observed higher dust levels around the mist bolting machine.

Jan 1, 2008

By E. Gaucher, M. St-Amant

"Among the electromagnetic surveys performed by SOQUEM in the last three years, a certain number of the more instructive cases have been chosen to illustrate the theory of electromagnetism by field examples of: (a) The depth penetration of the TURAM as compared to the SLINGRAM (Ronka) method. (b) The limitations of the TURAM as compared to the SLINGRAM method when a conductor dips the wrong way, or when it is small in size. (c) The expression of a shallow-dipping conductor in a SLINGRAM survey. (d) The effect on the SLINGRAM survey of deep ditches or reef structures.(e) A comparison between the CRONE and the SLING-RAM method in the Abitibi clay belt, by means of field and model studies, indicating a usually better signal-to-noise ratio for the SLINGRAM method. From the above and from other experiments, different electromagnetic methods are now being used by SOQUEM, depending on field conditions."

Jan 1, 1970

By B. Soundara, A. Suganya, S. Selvakumar

"Expansive soils have a potential for shrinkage or swelling under changing moisture content. Attempts were made to reduce the swelling potential of expansive soils with conventional additives such as lime, cement, etc. and non-conventional additives such as industrial wastes. In this research an attempt is made to study the feasibility of using granulated waste expanded polystyrene (EPS) as an additive to expansive soil to control swelling. To investigate the effect of mixing waste EPS granules with expansive clays, three expansive soils with different plasticity index were manufactured in the laboratory by mixing sand with sodium bentonite of various proportions. A series of standard proctor test, California bearing ratio (CBR) test, one dimensional free swell and swell pressure tests were performed on these soils. Test results show that the inclusion of EPS granules significantly reduces the percent swell and swelling pressure when subjected to one-dimensional free swell conditions. The dry density and CBR values decrease with increase in EPS content and increased plasticity of the soil.INTRODUCTIONExpansive soils cover an area of about 257 Million hectares on the earth’s surface (Dudal et al. 1965). In India, the area covered by expansive soils is nearly 20 percent of the total area (Mohan et al. 1961). Movement is usually in an uneven pattern and of such a magnitude as to cause extensive damage to various structures, especially lightly loaded structures or pavements (Chen 1975). Stabilization is one of the methods of treating the expansive soils to make them fit for civil engineering purposes. The variety of stabilizers may be broadly divided into three groups (Petry et al. 2002): (a) traditional stabilizers (lime, cement etc.), (b) by-product stabilizers (fly ash, quarry dust, phosphor-gypsum, slag etc.) and (c) non-traditional stabilizers (sulfonated oils, potassium compounds, polymer, enzymes, ammonium chlorides etc.). Apart from these, a number of other ground improvement techniques such as sand cushion technique (Satyanarayana 1966); cohesive nonswelling (CNS) layer technique (Katti 1978) were adopted for the stabilization of expansive soils. Expanded polystyrene (EPS) is a polymeric foam normally available in white colour and is a wellknown packaging material. The geotechnical specialists recognize EPS as the most commonly used geofoam material, a type of cellular geosynthetic which has been in consistent use in geotechnical applications since the early 1960s (Horvath 1995). EPS has very low thermal conductivity and nearly 98% of the volume is air (Lye et al. 2002). EPS has many exceptional properties such as being lightweight, thermal insulating, shock-absorbing and having low-water pick-up, etc. EPS find its applications in geotechnical engineering as light weight fills in the form of blocks (Refsdal 1985, Karpurapu et al. 1992, Zou 2001, Ikizler et al. 2008). EPS can be used as compressible inclusion and as a vibration damper (Horvath, 1994&1995). EPS is also used in lightweight concrete owing to its lightweight, excellent heat preservation and sound insulation properties (Ravindrarajah et al. 1994; Miledet al. 2004 and Babu et al. 2005). Waste EPS granules have been used in with horticultural soils to improve a number of soil characteristics like improving drainage, lightening heavy soils and improving water uptake capacity of soils (Scheirs 1998). Furthermore, it was also used as sub-base materials for pavements and railway track beds (Hanna 1978; Duskov1996), construction materials for floating marine structures and fenders in offshore oil platforms (Bagon et al. 1976), sea beds and sea fences; as an energy absorbing material for buried military structures, (Perry et al. 1991)."

Jan 1, 2017

By J. Dong

"Xanthate is a sulfide collector that has been widely used in flotation for almost a century. It is inexpensive, easy to synthesize and apply, and produces good metallurgy in the right applications. However, a major drawback of xanthate is that it decomposes easily and generates CS2 gas in transportation, storage and operation, which can be harmful to human health. Also, excessive xanthate in tailings pond leads to toxicity of the process water and potential damages to aqua-life systems. New regulations in Ontario require that the TWA (time-weighted-average) value of CS2 in the work place is below 1 ppm, which is 1/10 of the previous limit. The stringent regulation may eventually sweep other regions of Canada with the increased awareness of healthy working conditions and environment protection. Therefore, it becomes very important to find xanthate replacements which will be “green”, i.e., environmentally friendly.In this research work, a systematic procedure is used for collector evaluation using the Sudbury nickel sulfide ores from Vale’s Ontario operations, starting with the collector properties (MSDS) evaluation, followed by batch flotation tests, miniplant tests, plant trials and economic evaluation. It is found that the most promising xanthate replacement is dithiocarbamate.INTRODUCTIONSulfide mineral flotation has been practiced since the early 20th century. Its industrial importance is well recognized as mineral concentrates from flotation can be economically smelted and refined to provide primary metals. Collectors play a vital role in froth flotation. There are reagents possessing both a polar group that binds them to the mineral surface and a nonpolar group that is oriented away from the surface to attach air bubbles. The introduction of xanthate as a sulfide collector in 1925 was a remarkable development in froth flotation (Keller, 1925). It is low cost, easy to synthesize, water soluble, simple to control in application. Most importantly, it has strong capability and usually good selectivity for sulfide mineral flotation, which have been keeping its application prominent for almost a century."

Jan 1, 2011

By M. A. Trevits, A. Ozmet, A. C. Smith, J. B. Walsh, T. P. Mucho

Improvements in remote fire fighting technology are needed to reduce miner exposure to the dangers of fires and possibly save the lives of those who may become trapped. The National Institute for Occupational Safety and Health, in cooperation with U.S. Foam Technologies, Inc1., conducted a series of experiments at the NIOSH Lake Lynn Experimental Mine to study the stability, transport, control and fire extinguishing effectiveness of nitrogen-enhanced foam technology. This paper presents a description of the mine test configurations and experimental results

By Descour Jozef, Suguru Shirasagi, Takuji Yamamoto, Koji Murakami

For TBM tunneling no visual inspection of excavated ground is possible. This may hinder the high-speed excavation, particularly in complex ground conditions. The TBM Excavation Control System was developed for better prediction of geological conditions ahead of the tunnel face during excavation. The seismic reflector tracing produces volumetric images of anomalies in the ground in “near-real time.” These images are verified using logging data from pilot boring and TBM driving data, to improve reliability and precision of ground mapping. Also good correlation was obtained between the rock strength index computed from TBM data, and one derived from volumetric seismic images.

Jan 1, 2007

By Wilson D, Kirkland J

Compressed air energy storage (CAES) uses low cost off-peak energy to compress air and pump it into pressurised underground storage. Expanding the air through a modified form of gas turbine generates electrical energy when required. While generating power, a CAES station consumes approximately one-third of the gas required for the equivalent installed capacity of a conventional gas turbine. Air can be stored in underground rock caverns, caverns in salt domes, or in aquifers. Existing CAES power stations use caverns mined out of salt domes. Aquifer storage for CAES has been proposed, but not yet implemented. The groundwater in the aquifer would be displaced during air injection and when required the air would be extracted using the natural hydro-static pressure. Victoria has no salt domes, but has aquifers onshore in the Gippsland Basin with geological dome structures of suitable depth, discovery pressure, porosity, permeability and caprock for CAES development. Field tests costing several million dollars would be required to prove the suitability. The most suitable aquifer is near Seaspray, where several dome structures exist. The aquifer, comprising of coarse sands capped by coal and mudstone, is some 600 metres deep with a hydrostatic pressure of 6.3 MPa. Computer simulation of injection and extraction of air from the aquifer under various combinations of horizontal and vertical wells, permeability and tubing head pressures indicated the largest aquifer structure had the capacity to sustain a 300 MW station. A well field comprising of 24 directionally driven wells with a horizontal exposure to the aquifer would achieve the air flow rates required. Using plant similar to that recently installed at McIntosh Alabama USA, would mean high capital costs compared to standard gas turbine plant. However, a review of modem gas turbines indicated that they could be easily and economically adaptated to CAES duty. Adapting a 120 MW gas turbine would give 344 MW output. A separate air compression plant would be used. Economic evaluations indicate that, for gas prices above $1.95 per GJ, a 344 MW CAES plant is more economic for intermediate/reserve load duty than simple cycle gas turbines.

Jan 1, 1992

Evaluation of Grinding Medium Wear in Stirred Mills The standard fine grinding machines in the minerals industry are stirred mills whose performance largely depends on the competency of the grinding medium. Medium wear in stirred mills is one of the key parameters for medium selection. A wear evaluation methodology is developed and applied in this paper to measure the wear rate of river sand using a laboratory batch stirred mill. The procedure is demonstrated by testing the sand medium in a 0.55 kW batch stirred media detritor (SMD). The sand wear rate determined in the laboratory batch mill is successfully scaled up to that determined on a full-scale Metso 355 kW SMD mill.

Sep 13, 2010

By Ali Kahriman, Abdulkadir Karadogan, Deniz Adiquzel, Umit Ozer, Suat Bicer, Mehmet Aksoy

This paper presents the analysis and measurements of blast-induced ground vibrations during the construction of Istanbul Kagithane – Piyalepasa – Dolapdere – Dolmabahçe highway tunnels. These tunnels known as T1 and T2 are being constructed by a joint venture group. Within the scope of the study, the particle velocities and frequencies associated with 126 shots during the advancement of the tunnels were monitored and analyzed by vibration monitors at the test site. During the statistical analysis, three different predictor equations widely used in the literature were used to predict peak particle velocity (PPV) and the results and comparison of the predictor equations are presented in this paper. Finally, the particle velocities and frequency values of all blast events were evaluated according to USBM and German DIN 4150 Norms in order to determine the damage risks of the neighboring buildings and structures.

Jan 1, 2008